| Age | Commit message (Collapse) | Author |
|---|
|
Current R-Car sound SSI PIO/DMA mode are using interrupt.
it is no longer "xxx_pio_xxx", rename it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
L/R channel will be switched if under/over flow error happen on
Renesas R-Car sound device by the HW bugs. Then, HW restart is required
for salvage. This patch add salvage support for SSI.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Return the error code we got from clk_get() and check to make sure that
clk_prepare_enable() worked.
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The volume blocks have an step of 0.375dB, but TLV uses 0.01dB for
units. Only use the resolution supported, ignoring the LSB of the
volume register. This results in half the steps and 0.75dB per step,
but reports accurate levels through TLV. Update the masks to reflect
that these are registers have the LSB ignored.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
SSI component isn't unregistered if fsl_ssi_debugfs_create() fails
in probe phase.
To fix it, this commit replaces label error_asoc_register with
error_irq.
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Trying to remove the snd-soc-fsl-ssi module leads to the following warning:
[ 31.515336] ------------[ cut here ]------------
[ 31.520091] WARNING: CPU: 2 PID: 434 at fs/proc/generic.c:521 remove_proc_entry+0x14c/0x16c()
[ 31.528708] remove_proc_entry: removing non-empty directory 'irq/79', leaking at least '202c000.ss'
[ 31.537911] Modules linked in: snd_soc_wm8962 snd_soc_imx_wm8962 snd_soc_fsl_ssi(-) evbug
[ 31.546249] CPU: 2 PID: 434 Comm: rmmod Not tainted 3.18.0-rc6-00028-g3314bf6-dirty #1
[ 31.554235] Backtrace:
[ 31.556816] [<80011ea8>] (dump_backtrace) from [<80012044>] (show_stack+0x18/0x1c)
[ 31.564416] r6:80142c88 r5:00000000 r4:00000000 r3:00000000
[ 31.570267] [<8001202c>] (show_stack) from [<806980ec>] (dump_stack+0x88/0xa4)
[ 31.577588] [<80698064>] (dump_stack) from [<80029d78>] (warn_slowpath_common+0x70/0x94)
[ 31.585711] r5:00000009 r4:bb61fd90
[ 31.589423] [<80029d08>] (warn_slowpath_common) from [<80029e40>] (warn_slowpath_fmt+0x38/0x40)
[ 31.598187] r8:bb61fdfe r7:be05d76d r6:be05d9a8 r5:00000002 r4:be05d700
[ 31.605054] [<80029e0c>] (warn_slowpath_fmt) from [<80142c88>] (remove_proc_entry+0x14c/0x16c)
[ 31.613709] r3:806a79c0 r2:808229a0
[ 31.617371] [<80142b3c>] (remove_proc_entry) from [<80070380>] (unregister_irq_proc+0x94/0xb8)
[ 31.625989] r10:00000000 r8:8000ede4 r7:80955f2c r6:0000004f r5:8118e738 r4:be00af00
[ 31.633952] [<800702ec>] (unregister_irq_proc) from [<80069dac>] (free_desc+0x2c/0x64)
[ 31.641898] r6:0000004f r5:80955f38 r4:be00af00
[ 31.646604] [<80069d80>] (free_desc) from [<80069e68>] (irq_free_descs+0x4c/0x8c)
[ 31.654092] r7:00000081 r6:00000001 r5:0000004f r4:00000001
[ 31.659863] [<80069e1c>] (irq_free_descs) from [<8006fc3c>] (irq_dispose_mapping+0x40/0x5c)
[ 31.668247] r6:be17b844 r5:be17b800 r4:0000004f r3:802c5ec0
[ 31.673998] [<8006fbfc>] (irq_dispose_mapping) from [<7f004ea4>] (fsl_ssi_remove+0x58/0x70 [snd_so)
[ 31.683948] r4:bb5bba10 r3:00000001
[ 31.687618] [<7f004e4c>] (fsl_ssi_remove [snd_soc_fsl_ssi]) from [<803720a0>] (platform_drv_remove)
[ 31.697564] r5:7f0064f8 r4:be17b810
[ 31.701195] [<80372080>] (platform_drv_remove) from [<80370494>] (__device_release_driver+0x78/0xc)
[ 31.710361] r5:7f0064f8 r4:be17b810
[ 31.713987] [<8037041c>] (__device_release_driver) from [<80370d20>] (driver_detach+0xbc/0xc0)
[ 31.722631] r5:7f0064f8 r4:be17b810
[ 31.726259] [<80370c64>] (driver_detach) from [<80370304>] (bus_remove_driver+0x54/0x98)
[ 31.734382] r6:00000800 r5:00000000 r4:7f0064f8 r3:bb67f500
[ 31.740149] [<803702b0>] (bus_remove_driver) from [<80371398>] (driver_unregister+0x30/0x50)
[ 31.748617] r4:7f0064f8 r3:bd9f7080
[ 31.752245] [<80371368>] (driver_unregister) from [<80371f3c>] (platform_driver_unregister+0x14/0x)
[ 31.761498] r4:7f00655c r3:7f005a70
[ 31.765130] [<80371f28>] (platform_driver_unregister) from [<7f005a84>] (fsl_ssi_driver_exit+0x14/)
[ 31.776147] [<7f005a70>] (fsl_ssi_driver_exit [snd_soc_fsl_ssi]) from [<8008ed80>] (SyS_delete_mod)
[ 31.786553] [<8008ec64>] (SyS_delete_module) from [<8000ec20>] (ret_fast_syscall+0x0/0x48)
[ 31.794824] r6:00c46d18 r5:00000800 r4:00c46d18
[ 31.799530] ---[ end trace 954e8a3a15379e52 ]---
The cause of problem and solution are well explained by Lars-Peter:
"The driver creates the mapping by calling irq_of_parse_and_map(), so it also
has to dispose the mapping. But the easy way out is to simply use
platform_get_irq() instead of irq_of_parse_map(). In this case the mapping is
not managed by the device but by the of core, so the device has not to dispose
the mapping."
Tested on a imx6q-sabresd board.
Reported-by: Jiada Wang <jiada_wang@mentor.com>
Suggested-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Do not free BE hw if it's still used by other FE during dpcm runtime
shutdown. Otherwise the BE runtime state will be STATE_HW_FREE and
won't be updated to STATE_CLOSE when shutdown ends, because BE dai
shutdown function won't close pcm when detecting BE is still under
use. With STATE_HW_FREE, BE can't be triggered start again.
This corner case can easily appear when one BE is used by two FE,
without this patch "ASoC: dpcm: Fix race between FE/BE updates and
trigger"(ea9d0d771fcd32cd56070819749477d511ec9117). One FE tries to
shutdown but it's raced against xrun on another FE. It improves the
be dai hw_free logic.
Signed-off-by: Qiao Zhou <zhouqiao@marvell.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
If a snd_soc_card has any DAPM routes when it calls
snd_soc_of_parse_audio_routing, those are clobbered without this change.
Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
rsnd_src_start/stop() requests struct rsnd_dai as parameter.
but, it is not used, and become more complex in L/R error handling.
Let's remove it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Basically, SSI starting method is same between PIO/DMA mode.
Let's share it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Current src.c sets SRC_ROUTE_MODE0 on rsnd_src_start(), but, set it in
rsnd_src_set_convert_rate() is natural.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Current src initialize SRC on rsnd_src_set_convert_rate()
but, it should be done on rsnd_src_init().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
using many rsnd_src_convert_rate() is not readable.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Avoid NULL pointer access
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Current DVC is using snd_kcontrol_new functions, but, SRC will need
same method. Move common functions to core.c
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
master clock rate is useful information for debug.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Current SSI start/stop sequence is different between PIO/DMA mode,
but, almost all are same. this patch synchronize it.
It will be shared in the future.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Let's clear SSI status when HW start
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Current SSI is careing SSIWSR which controls WS continue mode when
DMA mode, but, it should be cared when PIO mode too.
This patch fixup it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Current SSI doesn't care interrupt "disable" method. And, it is used
when PIO mode only at this point. SSI interrupt will be used for
sound R/L issue workaround when DMA mode too.
This patch tidyup SSI interrupt enable/disable method.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Current ssi.c has .cr_etc which is used for SSICR's
etc settings. but, it is used as PIO/DMA switching purpose now.
This patch tidyup this method. This is prepare for
under/over run issue handling
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
rsnd_src_ssiu_stop() is used to stop SSIU,
but it shouldn't depend on whether it is using SSIU.
This patch stops SSIU compulsorily.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
R-Car sound can use SSI/SRC/DVC modules, and these are controlled as
rsnd_mod in rsnd driver. These rsnd_mod has each own function as
callback. Basically these callback function has pair like probe/remove,
start/stop, etc. And, these functions are called by order to each stage
like below.
1. src->probe
2. ssi->probe
3. dvc->probe
4. src->start
5. ssi->start
6. dvc->start
7. src->stop
8. ssi->stop
9. dvc->stop
10. src->remove
11. ssi->remove
12. dvc->remove
But, current rsnd driver doesn't care about its status which indicates
which function is called.
For example, if 5) returns error, 6) is not called. In such case,
9) should not be called. This patch care about each modules status.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Current R-Car sound has PIO fallback support if it couldn't use DMA.
This fallback is done in .remove callback, but, it should have
.fallback callback. Otherwise, normal .remove callback will have
strange behavior. This patch adds .fallback callback.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
"of_node_put"
The of_node_put() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The clk_disable() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Prepare for the introduction of device-tree support by re-ordering some
of the allocations and using devm_iomap_resource to simplify IO mapping.
Signed-off-by: Andrew Jackson <Andrew.Jackson@arm.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Now that the driver snd-soc-afeb9260.c is deleted, remove its Kconfig option.
Reported-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
During the removal of all AT91 !DT boards, we removed the AFEB9260. This driver
is !DT and was only used by this board, so we delete it as well.
Reported-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Removes omap-hdmi DAI driver, omap-hdmi-card driver, the related
Kconfig options, and Makefile entries. The HDMI DAI drivers has been
integrated directly to OMAP4+ HDMI drivers and simple-card driver is
used instead of omap-hdmi-card driver.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
The platform device should only be registered from OMAPDSS HDMI
driver. The platform driver registers and unregisters all ASoC
components needed for OMAP HDMI audio.
The hdmi audio driver implements cpu-dai component using the callbacks
provided by OMAPDSS and registers the component under DSS HDMI
device. Omap-pcm is registered for platform component also under DSS
HDMI device. Dummy codec is used as as codec component. The hdmi audio
driver implements also the card and registers it under its own
platform device.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
Move capture PCM pin from PCM4 to PCM0 for Broadwell/Haswell.
This will allow us to integrate with pulseaudio better for
usually default device is set to 0.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The xmax volume should be corrected to ARRAY_SIZE(volume_map)-1, otherwise,
the xmax value will be mapped to 0 wrongly.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
According to the sgtl5000 datasheet the MCLK frequency range restriction of
8 to 27 MHz only applies when the PLL is used - synchronous SYS_MCLK input mode.
mxs-sgtl5000 machine sets the codec as slave, and mx28 generates MCLK in the
range of 256*fs, 384*fs or 512*fs, which is called asynchronous SYS_MCLK
input.
In asynchronous SYS_MCLK we cannot have the 8 to 27 MHz check because if we
want to play a 8KHz sample rate track, with a MCLK of 8k * 512 = 4.096MHz the
current check would return -EINVAL, which is not correct.
Remove the 8 to 27MHz frequency check, since this only applies to the
synchronous SYS_MCLK input case.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When trying to play a 8kHz file with codec in slave mode we get the following
error on a mx28evk:
$ aplay -Dhw:0,0 stereo_8k.wav
Playing WAVE 'stereo_8k.wav' : Signed 16 bit Little Endian, Rate 8000 Hz, Stereo
[ 21.218647] sgtl5000 0-000a: PLL not supported in slave mode
[ 21.224559] sgtl5000 0-000a: 128 ratio is not supported. SYS_MCLK needs to be 256, 384 or 512 * fs
[ 21.233687] sgtl5000 0-000a: ASoC: can't set sgtl5000 hw params: -22
aplay: set_params:1123: Unable to install hw params:
This error happens because we are using 'sys_fs' instead of 'frame_rate' in the
valid ratio check.
Use the real'frame_rate' so that the ratio is correctly calculated and the
playback can run.
sgtl5000 codec manual states that in 'Synchronous SYS_MCLK input' mode that the
following SYS_CLK frequencies are allowed: 256*fs, 384*fs, 512*fs.
, where fs is the sampling frequency, which can be in the range of:
8, 11.025, 16, 22.5, 32, 44.1, 48, 96 kHz.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
According to the sgtl5000 datasheet the MCLK frequency range restriction of
8 to 27 MHz only applies when the PLL is used - synchronous SYS_MCLK input mode.
When running the codec as slave, the master should generate MCLK in the range of
256*fs, 384*fs or 512*fs, which is called asynchronous SYS_MCLK input mode.
In asynchronous SYS_MCLK we cannot have the 8 to 27 MHz check because if we
want to play a 8KHz sample rate track, with a MCLK of 8k * 512 = 4.096MHz the
current check would return -EINVAL, which is not correct.
Remove the 8 to 27MHz frequency check, since this only applies to the
synchronous SYS_MCLK input case.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Set the CODEC driver's suspend_bias_off flag rather than manually going to
SND_SOC_BIAS_OFF in suspend and SND_SOC_BIAS_STANDBY in resume. This makes
the code a bit shorter and cleaner.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Remove the manual transition back to SND_SOC_BIAS_STANDBY in resume. This
is already be automatically handled by the ASoC core.
Since the ASoC core now takes care of setting the bias level to
SND_SOC_BIAS_OFF when removing the CODEC there is no need to do it manually
anymore either.
The manual transition to SND_SOC_BIAS_STANDBY at the end of CODEC probe()
can also be removed as the core will automatically do this after the CODEC
has been probed. While we are at it also remove the unused codec field from
the cq93vc struct so the whole probe function can be removed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
While two of the fields in the cq93vc driver state struct are initialized
none of them are ever acutally read again. So remove the whole struct.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
On Broadwell, the ADSP FW don't support loopback record volume tuning,
so here remove this control.
Signed-off-by: Jie Yang <yang.jie@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The "changed" variable should be set to false at the start.
Fixes: a35daac77a03 ('ASoC: sigmadsp: Add support for fw v2')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
|
|
We must ensure that the clocking configuration is valid as rapidly as possible.
And do software reset before the others registers updates, or the registers
will be reset to the default state.
Signed-off-by: Zidan Wang <b50113@freescale.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
