| Age | Commit message (Collapse) | Author |
|---|
|
'asoc/fix/pxa', 'asoc/fix/rcar' and 'asoc/fix/sigmadsp' into asoc-linus
|
|
|
|
Commit 432481220 (ASoC: fsl-ssi: Use regmap) removed struct ccsr_ssi.
Unfortunately, the structure is still used. This causes
mpc85xx_smp_defconfig and mpc85xx_defconfig builds to fail with
sound/soc/fsl/fsl_dma.c:926:50:
error: invalid use of undefined type 'struct ccsr_ssi'
dma->ssi_stx_phys = res.start + offsetof(struct ccsr_ssi, stx0);
ound/soc/fsl/fsl_dma.c:927:50:
error: invalid use of undefined type 'struct ccsr_ssi'
dma->ssi_srx_phys = res.start + offsetof(struct ccsr_ssi, srx0);
Fix by using constants, similar to original commit.
Cc: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Index of dma name should use -1, not +1 when capture case.
Thank you Dan.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
The calculation code does
u64 = (u32 - u32) * 100000;
The 64 bits are of no help here as the type is casted only after the
multiplication, and therefore the result may overflow, possibly causing
inoptimal or wrong clock setup in an unfortunate case (the maximum
result value of the first substraction is currently 47999).
Fix the code to cast before multiplication.
Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi>
Acked-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
We should not copy the return value into this val since it's supposed to
get the value of the register not the success result of regmap_read().
Thus fix it.
Signed-off-by: Nicolin Chen <Guangyu.Chen@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Commit c9e065c27fe9 ("ASoC: dapm: Make sure to always update the DAPM graph
in _put_volsw()") stopped updating register values in those cases where
initial after boot state of kcontrol appears to not change but where
register value still needs update because it is not in sync with the
kcontrol state.
Fix this by doing snd_soc_test_bits() unconditionally as it was before but
by using separate flags for kcontrol and register state changes. This allow
both DAPM graph to be updated when disabling auto-muted control and update
register if it is out-of-sync in respect of kcontrol state.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
When the SigmaDSP module is built-in, but the I2C core is build as a module
we'll get a undefined reference:
sound/built-in.o: In function `sigma_action_write_i2c':
:(.text+0x5d8d4): undefined reference to `i2c_master_send'
This can happen if a audio driver that is using the regmap SigmaDSP interface is
built into the kernel, but core I2C support is build as a module. To fix this
split the SigmaDSP module into three modules, one module providing the core
infrastructure and two small modules implementing the regmap and I2C interfaces.
This allows e.g. the core infrastructure and regmap support to be built into the
kernel while I2C support can still be build as a module.
Fixes: dab464b60 ("ASoC: Add ADAU1361/ADAU1761 audio CODEC support")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
From e7a94bb7fb871c73cc85712d89c1f48d0271c1be Mon Sep 17 00:00:00 2001
From: Arnd Bergmann <arnd@arndb.de>
Date: Thu, 5 Jun 2014 12:31:28 +0200
Subject: [PATCH] ASoC: MMP audio needs sram support
Building the pxa/mmp audio driver without support for the mmp
sram driver enabled results in this link error:
sound/built-in.o: In function `mmp_pcm_free_dma_buffers':
:(.text+0x3e734): undefined reference to `sram_get_gpool'
sound/built-in.o: In function `mmp_pcm_new':
:(.text+0x3e7c0): undefined reference to `sram_get_gpool'
The sram driver is cannot be manually enabled and needs to
be turned on by selecting MMP_SRAM from each module that
needs it, which is what this patch does.
Ideally, MMP should move over to the generic SRAM support, but
for the moment, we can avoid the build error.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Qiao Zhou <zhouqiao@marvell.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound into next
Pull sound updates from Takashi Iwai:
"At this time, majority of changes come from ASoC world while we got a
few new drivers in other places for FireWire and USB. There have been
lots of ASoC core cleanups / refactoring, but very little visible to
external users.
ASoC:
- Support for specifying aux CODECs in DT
- Removal of the deprecated mux and enum macros
- More moves towards full componentisation
- Removal of some unused I/O code
- Lots of cleanups, fixes and enhancements to the davinci, Freescale,
Haswell and Realtek drivers
- Several drivers exposed directly in Kconfig for use with
simple-card
- GPIO descriptor support for jacks
- More updates and fixes to the Freescale SSI, Intel and rsnd drivers
- New drivers for Cirrus CS42L56, Realtek RT5639, RT5642 and RT5651
and ST STA350, Analog Devices ADAU1361, ADAU1381, ADAU1761 and
ADAU1781, and Realtek RT5677
HD-audio:
- Clean up Dell headset quirks
- Noise fixes for Dell and Sony laptops
- Thinkpad T440 dock fix
- Realtek codec updates (ALC293,ALC233,ALC3235)
- Tegra HD-audio HDMI support
FireWire-audio:
- FireWire audio stack enhancement (AMDTP, MIDI), support for
incoming isochronous stream and duplex streams with timestamp
synchronization
- BeBoB-based devices support
- Fireworks-based device support
USB-audio:
- Behringer BCD2000 USB device support
Misc:
- Clean up of a few old drivers, atmel, fm801, etc"
* tag 'sound-3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (480 commits)
ASoC: Fix wrong argument for card remove callbacks
ASoC: free jack GPIOs before the sound card is freed
ALSA: firewire-lib: Remove a comment about restriction of asynchronous operation
ASoC: cache: Fix error code when not using ASoC level cache
ALSA: hda/realtek - Fix COEF widget NID for ALC260 replacer fixup
ALSA: hda/realtek - Correction of fixup codes for PB V7900 laptop
ALSA: firewire-lib: Use IEC 61883-6 compliant labels for Raw Audio data
ASoC: add RT5677 CODEC driver
ASoC: intel: The Baytrail/MAX98090 driver depends on I2C
ASoC: rt5640: Add the function "get_clk_info" to RL6231 shared support
ASoC: rt5640: Add the function of the PLL clock calculation to RL6231 shared support
ASoC: rt5640: Add RL6231 class device shared support for RT5640, RT5645 and RT5651
ASoC: cache: Fix possible ZERO_SIZE_PTR pointer dereferencing error.
ASoC: Add helper functions to cast from DAPM context to CODEC/platform
ALSA: bebob: sizeof() vs ARRAY_SIZE() typo
ASoC: wm9713: correct mono out PGA sources
ALSA: synth: emux: soundfont.c: Cleaning up memory leak
ASoC: fsl: Remove dependencies of boards for SND_SOC_EUKREA_TLV320
ASoC: fsl-ssi: Use regmap
ASoC: fsl-ssi: reorder and document fsl_ssi_private
...
|
|
We have in the past added 'depends on I2C' for some of the PXA boards
after hitting randconfig build bugs. I have seens a couple of new
bugs in this area during the linux-next cycle for 3.16, after it
became possible to build some more PXA machines with I2C disabled.
To shut this up for good, this adds the dependency to every board
that uses I2C as the interface to the codec. I have gone through
all board files and verified that they all either use AC97 or
I2C, and this annotates the latter. Some of these already enable
I2C from mach-pxa/Kconfig, but since that can change it's better
to be explicit here.
The link error that can result otherwise happens when CONFIG_I2C
is set to 'm' and the codec driver is built-in as a result of being
selected by the platform specific glue.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
The commit [e1d4d3c8: ASoC: free jack GPIOs before the sound card is
freed] introduced snd_soc_card remove callbacks to a few drivers, but
they are implemented with a wrong argument type. The callback should
receive snd_soc_card pointer instead of snd_soc_pcm_runtime.
Fixes: e1d4d3c854f2 ('ASoC: free jack GPIOs before the sound card is freed')
Acked-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This is the same change as commit fb6b8e71448a "ASoC: tegra: free jack
GPIOs before the sound card is freed", but applied to all other ASoC
machine drivers where code inspection indicates the same problem exists.
That commit's description is:
==========
snd_soc_jack_add_gpios() schedules a work queue item to poll the GPIO to
generate an initial jack status report. If sound card initialization
fails, that work item needs to be cancelled, so it doesn't run after the
card has been freed. Specifically, freeing the card calls
snd_jack_dev_free() which calls snd_jack_dev_disconnect() which sets
jack->input_dev = NULL, and input_dev is used by snd_jack_report(), which
is called from the work queue item.
snd_soc_jack_free_gpios() cancels the work item. The Tegra ASoC machine
drivers do call this function in the platform driver remove() callback.
However, this happens after the sound card is freed, at least when the
card is freed due to errors late during snd_soc_instantiate_card(). This
leaves a window where the work item can execute after the card is freed.
In next-20140522, sound card initialization does fail for unrelated
reasons, and hits the problem described above.
To solve this, fix the Tegra ASoC machine drivers to clean up the Jack
GPIOs during the snd_soc_card's .remove() callback, which is executed
before the overall card object is freed. also, guard the cleanup call
based on whether we actually setup up the GPIOs in the first place.
Ideally, we'd do the cleanup in a struct snd_soc_dai_link .fini/remove
function to match where the GPIOs get set up. However, there is no such
callback.
==========
Note that I have not even compile-tested this in most cases, since most
of the drivers rely on specific mach-* support I don't have enabled, and
don't support COMPILE_TEST. Testing by the relevant board maintainers
would be useful.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
into asoc-next
|
|
|
|
'asoc/topic/simple' and 'asoc/topic/sirf' into asoc-next
|
|
into asoc-next
|
|
asoc-next
|
|
'asoc/topic/max98095' into asoc-next
|
|
asoc-next
|
|
|
|
|
|
|
|
|
|
asoc-next
|
|
|
|
into asoc-linus
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc into next
Pull part one of ARM SoC updates from Olof Johansson:
"A quite large set of SoC updates this cycle. In no particular order:
- Multi-cluster power management for Samsung Exynos, adding support
for big.LITTLE CPU switching on EXYNOS5
- SMP support for Marvell Armada 375 and 38x
- SMP rework on Allwinner A31
- Xilinx Zynq support for SOC_BUS, big endian
- Marvell orion5x platform cleanup, modernizing the implementation
and moving to DT.
- _Finally_ moving Samsung Exynos over to support MULTIPLATFORM, so
that their platform can be enabled in the same kernel binary as
most of the other v7 platforms in the tree. \o/
The work isn't quite complete, there's some driver fixes still
needed, but the basics now work.
New SoC support added:
- Freescale i.MX6SX
- LSI Axxia AXM55xx SoCs
- Samsung EXYNOS 3250, 5260, 5410, 5420 and 5800
- STi STIH407
plus a large set of various smaller updates for different platforms.
I'm probably missing some important one here"
* tag 'soc-for-3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (281 commits)
ARM: exynos: don't run exynos4 l2x0 setup on other platforms
ARM: exynos: Fix "allmodconfig" build errors in mcpm and hotplug
ARM: EXYNOS: mcpm rename the power_down_finish
ARM: EXYNOS: Enable mcpm for dual-cluster exynos5800 SoC
ARM: EXYNOS: Enable multi-platform build support
ARM: EXYNOS: Consolidate Kconfig entries
ARM: EXYNOS: Add support for EXYNOS5410 SoC
ARM: EXYNOS: Support secondary CPU boot of Exynos3250
ARM: EXYNOS: Add Exynos3250 SoC ID
ARM: EXYNOS: Add 5800 SoC support
ARM: EXYNOS: initial board support for exynos5260 SoC
clk: exynos5410: register clocks using common clock framework
ARM: debug: qcom: add UART addresses to Kconfig help for APQ8084
ARM: sunxi: allow building without reset controller
Documentation: devicetree: arm: sort enable-method entries
ARM: rockchip: convert smp bringup to CPU_METHOD_OF_DECLARE
clk: exynos5250: Add missing sysmmu clocks for DISP and ISP blocks
ARM: dts: axxia: Add reset controller
power: reset: Add Axxia system reset driver
ARM: axxia: Adding defconfig for AXM55xx
...
|
|
It is not an error to have no cache so we shouldn't return an error code
and cause our callers to fail, just silently do nothing instead. Thanks
to Jarkko for identify the problematic commit.
Reported-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reported-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
This patch adds the Realtek ALC5677 codec driver.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
The patch adds the function "get_clk_info" to RL6231 shared support.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
support
The patch adds the function of the PLL clock calculation to RL6231 shared
support.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
RT5651
The patch adds the RL6231 class device shared support for RT5640, RT5645 and
RT5651. The function of the DMIC clock calculation can be shared by RL6231
shared support.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into asoc-rl6231
|
|
Since we cannot make sure the 'reg_size' will always be none zero here,
and then if 'reg_size' equals to zero, the kzalloc() will return ZERO_SIZE_PTR,
which equals to ((void *)16).
So this patch fix this with just doing the 'reg_size' zero check before calling
kzalloc().
Signed-off-by: Xiubo Li <Li.Xiubo@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into asoc-fsl-ssi
Conflicts:
sound/soc/fsl/Kconfig
|
|
The mono output PGA input only has four possible sources, so
omit the rest.
Signed-off-by: Matt Reimer <mreimer@sdgsystems.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Eukrea-i.MX51 board was converted to use DT, ie we no longer have a
MACH_EUKREA_MBIMXSD51_BASEBOARD symbol.
Transformation of other boards planned for the near future, so this
patch removes all these dependencies and restricts build of this
driver to ARCH_MXC.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
This patch replaces the ssi specific functions write_ssi, read_ssi and
write_ssi_mask by standard regmap function calls.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Tested-By: Michael Grzeschik <mgr@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Reorder all variables in struct fsl_ssi_private to have groups that make
sense together. The patch also updates the struct documentation.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Tested-By: Michael Grzeschik <mgr@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
The baudclock may be used and set by different streams.
Allow only the first stream to set the bitclock rate. Other streams have
to try to get to the correct rate without modifying the bitclock rate
using the SSI internal clock modifiers.
The variable baudclk_streams is introduced to keep track of the active
streams that are using the baudclock. This way we know if the baudclock
may be set and whether we may enable/disable the clock.
baudclock enable/disable is moved to hw_params()/hw_free(). This way we can
keep track of the baudclock in those two functions and avoid a running
clock while it is not used. As hw_params()/hw_free() may be called
multiple times for the same stream, we have to use baudclk_streams
variable to know whether we may enable/disable the clock.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Tested-By: Michael Grzeschik <mgr@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
In i2s master mode the fsl_ssi driver depends on someone calling
.set_tdm_slot correctly. In this mode though only a DC value of
2 is allowed, so set it in this case and no longer depend on
.set_tdm_slot.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Tested-By: Michael Grzeschik <mgr@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
The baudclock_locked variable is only used in functions which
are serialized anyway from the core. No need to have a lock
around the variable, so remove it.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Tested-By: Michael Grzeschik <mgr@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
The fsl_ssi driver uses the .set_sysclk callback to configure the
bitclock for master mode. This is unnecessary since the bitclock
is known in hw_params. This patch configures the bitclock from .hw_params.
.set_dai_sysclk now sets a bitclock frequency which is preferred over
the default calculated bitclock frequency.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Tested-By: Michael Grzeschik <mgr@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
The simple soundcard binding has its own way for specifying the dai
format. To be able to use this binding we have to make the fsl,mode
property optional. As the property is used in existing devicetrees
keep the option around for compatibility reasons.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Tested-By: Michael Grzeschik <mgr@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Introduce a SoC data struct which contains the differences between
the different SoCs this driver supports. This makes it easy to support
more differences without having to introduce a new switch/case each
time.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Tested-By: Michael Grzeschik <mgr@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Use card PM ops from ASoC core instead of defining custom PM ops here since
we are calling anyway common suspend/resume callbacks.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Simplify byt-rt5640.c and haswell.c machine drivers by using
devm_snd_soc_register_card(). Remove also needless dev_set_drvdata()
from byt_rt5640_probe() since snd_soc_register_card() does it too.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Cc: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
A few files contain duplicate headers. This patch removes the second entry of
duplicate in each file under question.
There is no functional changes.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Cc: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
