| Age | Commit message (Collapse) | Author |
|---|
|
H3 ASoC supports 12Khz and 24Khz audio sample rates but the current
drivers doesn't advertise these rates properly and they cannot be used.
For example attempt to capture at 12Khz uses 11Khz (same applies to
audio playback):
Recording raw data '/tmp/testS16_LE.raw' : Signed 16 bit Little Endian, Rate 12000 Hz, Stereo
Warning: rate is not accurate (requested = 12000Hz, got = 11025Hz)
This patch fixes the audio sample rates declared and supported by the
driver according to the H3 data sheet. Specifically for audio playback:
8000, 11050, 12000, 16000, 22050, 24000, 32000, 44100, 48000, 96000, 192000
and for audio capture:
8000, 11050, 12000, 16000, 22050, 24000, 32000, 44100, 48000
Signed-off-by: Andrea Bondavalli <andrea.bondavalli74@gmail.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
32bit and 24bit audio capture formats for H3/H2+ are broken because the
RX_SAMPLE_BITS and the RX_FIFO_MODE bits of AC_ADC_FIFOC register of the audio
codec are not set to operate in 24bit mode but in 16bit mode only.
The following patch sets the H3 audio codec registers and the DMA bus width
properly when a 24/32bit capture is requested.
Signed-off-by: Andrea Bondavalli <andrea.bondavalli74@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
First of all,the address of pdev->dev is assigned to card->dev in
create_card,then the function platform_set_drvdata copies the value
the variable card to pdev->dev.driver_data, but when calling
snd_soc_register_card,the function dev_set_drvdata(card->dev, card)
will also do the same copy operation,so i think that the former copy
operation can be removed.
Signed-off-by: Peng Donglin <dolinux.peng@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Declare snd_soc_codec_driver structures as const as they are either
passed as an argument to the function snd_soc_register_codec or stored as
reference in field codec of type sun4i_codec_quirks. Both the fucntion
argument and the codec field are of type const, so declare the
structures with this property as const.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Commit a53e35db70d1 ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.
No functional changes.
Cc: Liam Girdwood <lgirdwood@gmail.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: alsa-devel@alsa-project.org
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The gpiod API checks for NULL descriptors, so there is no need to
duplicate the check in the driver.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The codec in the V3s is similar to the one found on the A31. One key
difference is the analog path controls are routed through the PRCM
block. This is supported by the sun8i-codec-analog driver, and tied
into this codec driver with the audio card's aux_dev.
In addition, the V3s does not have LINEIN, LINEOUT, MBIAS and MIC2,
MIC3, and the FIFO related registers are like H3.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The mono differential output for "Line Out" downmixes the stereo audio
from the mixer, instead of just taking the left channel.
Add a route from the "Right Mixer" to "Line Out Source Playback Route"
through the "Mono Differential" path, so DAPM doesn't shut down
everything if the left channel is muted.
Fixes: 0f909f98d7cb ("ASoC: sun4i-codec: Add support for A31 Line Out
playback")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The codec on the H3 is similar to the one found on the A31. One key
difference is the analog path controls are routed through the PRCM
block. This is supported by the sun8i-codec-analog driver, and tied
into this codec driver with the audio card's aux_dev.
In addition, the H3 has no HP (headphone) and HBIAS support, and no
MIC3 input. The FIFO related registers are slightly rearranged.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The codec in the A23 is similar to the one found on the A31. One key
difference is the analog path controls are routed through the PRCM
block. This is supported by the sun8i-codec-analog driver, and tied
into this codec driver with the audio card's aux_dev.
In addition, the A23 does not have LINEOUT, and it does not support
headset jack detection or buttons.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
sound/soc/sunxi/sun4i-codec.c:1339:2-3: Unneeded semicolon
Remove unneeded semicolon.
Generated by: scripts/coccinelle/misc/semicolon.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The later Allwinner SoCs have a dedicated reset controller, and
peripherals have dedicated reset controls which need to be deasserted
before the associated peripheral can be used.
Add support for this to the quirks structure and probe/remove functions.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The A31's internal codec capture path has a mixer in front of the ADC
for each channel, capable of selecting various inputs, including
microphones, line in, phone in, and the main output mixer.
This patch adds the various controls, widgets and routes needed for
audio capture from the already supported inputs on the A31.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The A31 SoC's codec has various inputs, outputs and microphone bias
supplies. These can be routed on the board in different ways, such as:
- HPCOM may be connected to have the headphone DC coupled.
- Microphones all use the MBIAS main microphone supply or one mic may
use the HBIAS supply, which supports headset detection and buttons.
- Line Out may be routed to an audio jack, or an onboard speaker amp
with power controls.
Add support for specifying the audio routes in the device tree.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The A31 internal codec has 3 microphone outputs, of which MIC2 and MIC3
are muxed internally. The resulting two microphone inputs have separate
gain controls and mixer inputs.
The codec also has 2 microphone bias pins. HBIAS is specifically for the
headphone jack, which also supports headphone detection and control
buttons. These extra functions are not supported yet. The other, MBIAS,
is for all other analog microphones.
There is also mention of digital microphone support, but documentation
is scarce, and no hardware with it is available.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The A31 integrated codec has a second "Line Out" output which does not
include an integrated amplifier in its path. This path does have a
separate volume control.
This patch adds support for the playback path from the DAC to the Line
Out pins.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The A31 integrated codec has a stereo "Line In" input. Add support for
it to the playback paths.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The A31 has a similar codec to the A10/A20. The PCM parts are very
similar, with different register offsets. The analog paths are very
different. There are more inputs and outputs. The ADC mux has been
replaced with a proper mixer.
This patch adds support for the basic playback path of the A31 codec,
from the DAC to the headphones. Headphone detection, microphone,
signaling, other inputs/outputs and capture will be added later.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
According to the DMA engine API documentation, maxburst denotes the
largest possible size of a single transfer, so as not to overflow
destination FIFOs as explained in this excerpt from dmaengine.h
* @src_maxburst: the maximum number of words (note: words, as in
* units of the src_addr_width member, not bytes) that can be sent
* in one burst to the device. Typically something like half the
* FIFO depth on I/O peripherals so you don't overflow it. This
* may or may not be applicable on memory sources.
* @dst_maxburst: same as src_maxburst but for destination target
* mutatis mutandis.
The TX FIFO is 64 samples deep for stereo, and the RX FIFO is 16
samples deep. So maxburst could be 32 and 8 for TX and RX respectively.
Unfortunately the sunxi DMA controller driver takes maxburst as
the requested burst size, rather than a limit, and returns an error
for unsupported values. The original value was 4, but some later
SoCs do not officially support this burst size.
This patch increases maxburst on the TX side to 8, which is supported
by all variants of the sunxi DMA controller.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The A31 has a similar codec to the A10/A20. The PCM parts are very
similar, with just different register offsets. The analog paths are
very different. There are more inputs and outputs.
The A31s, A23, and H3 have a similar PCM interface, again with register
offsets slightly rearranged. The analog path controls, while very
similar between them and the A31, have been moved a separate bus which
is accessed through a message box like interface in the PRCM address
range. This would be handled by a separate auxiliary device tied in
through the device tree in its supporting create_card function.
The quirks structure is expanded to include different register offsets
and separate callbacks for creating the ASoC card. The regmap_config,
quirks, and of_device_match tables have been moved to facilitate this.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into asoc-sunxi
|
|
This revises existing comments in the register definition macros
section, and adds a few more, so that readers can clearly identify
the types of control registers.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The audio codec on later Allwinner SoCs have a different layout and
audio path compared to the A10/A20. However the PCM parts are still
the same.
The different layout and audio paths mean we need a different
create_card function for different families, so they can create
DAPM endpoint widgets and routes.
This patch moves the regmap configs, quirks and of_device_id
structures to just before the probe function, so we can, among other
things, include a pointer for the create_card function. None of the
lines of code were changed.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In the current probe function the GPIO is acquired after the codec's
bus clock is enabled. However if it fails to acquire the GPIO due to
a deferred probe, it does not disable the bus clock before bailing out.
This would result in the clock being enabled multiple times.
Move the code that enables the bus clock after the part that gets the
GPIO, maintaining a separation between resource acquisition and device
enablement in the probe function.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When sun4i_codec_create_card fails, we do not assign a proper error
code to the return value. The return value would be 0 from the previous
function call, or we would have bailed out sooner. This would confuse
the driver core into thinking the device probe succeeded, when in fact
it didn't, leaving various devres based resources lingering.
Make the create_card function pass back a meaningful error code, and
assign it to the return value.
Fixes: 45fb6b6f2aa3 ("ASoC: sunxi: add support for the on-chip codec on
early Allwinner SoCs")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Rename "sun4i_codec_widgets" to "sun4i_codec_controls" for
consistency with the struct field name.
Signed-off-by: Danny Milosavljevic <dannym@scratchpost.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into asoc-sunxi
|
|
The A20 has a few extra registers that the A10 doesn't have.
Therefore, use different regmaps for A10 as compared to A20.
Signed-off-by: Danny Milosavljevic <dannym@scratchpost.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Some of the registers defined in the driver are only usable on the
A20. Rename these registers.
Signed-off-by: Danny Milosavljevic <dannym@scratchpost.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
codec driver and component driver has duplicated callback functions,
and codec side functions are just copied to component side when
register timing. This was quick-hack, but no longer needed.
This patch moves these functions from codec driver to component driver.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
An external amp (if any) is connected to the external outputs of the SoC
of course, rather then directly to the internal amp.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add support for PA gpio pin for controlling an external amplifier as used
on some Allwinner boards.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Rename the codec dapm widgets and routes with a _codec prefix. This is
a preparation patch for adding card dapm widgets and routes.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into asoc-sunxi
|
|
Commit 1fb34b48361e ('ASoC: sun4i: Implement MIC1 capture') added back some
code that disregards the clk_set_rate error code and always returns
-EINVAL. Fix that and return the code in order to have more clue about
what's going on.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The comment is misleading on how we should support external power amps, and
the variable is not used and generates a warning.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
One of the input path used in the Allwinner codec is the MIC1. Add support
for it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The power amplifier for the headphone output is called "the PA" and "the
headphone amplifier" in Allwinner's documentation for the A10 and A20.
sun4i-codec calls it "PA" in some places and "Pre-Amplifier" (which
isn't really accurate) in others, leading to user-visible controls with
different names referring to the same device.
When this driver implements audio input, it'll also need to expose
controls for the line and mic input preamps, so just referring to "the
Pre-Amplifier" will be ambiguous.
Change it to use "Power Amplifier" consistently for the power
amplifier's controls.
Signed-off-by: Adam Sampson <ats@offog.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Most of the boards have their headphone jack directly connected to the
matching pins of the SoCs. Since most of the time we will have the same
routing path, it makes no sense to put that in the DTS, since it will only
be some useless duplication there.
It also fixes the following warning messages that were seen so far, on
boards where we were using the bindings in the documentation example.
sun4i-codec 1c22c00.codec: ASoC: no sink widget found for Headphone Jack
sun4i-codec 1c22c00.codec: ASoC: Failed to add route HP Left -> direct -> Headphone Jack
sun4i-codec 1c22c00.codec: ASoC: no sink widget found for Headphone Jack
sun4i-codec 1c22c00.codec: ASoC: Failed to add route HP Right -> direct -> Headphone Jack
Reported-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The SND_PCM_RATE_KNOT covers all the rate settings, even though some that
we don't support, while we also list all the rate we support. Simply remove
it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The current code, disregarding the clk_set_rate error code, was always
returning -EINVAL. Fix that and return the code in order to have more clue
about what's going on.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
sound/soc/sunxi/sun4i-codec.c:708:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
CC: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The sun4i, sun5i and sun7i SoC families have a built-in codec, capable
of both audio capture and playback.
While this is called a codec by Allwinner, it really is an in-SoC
combination of a codec and a DAI, with its own DAC/ADC and amplifiers
in a single memory-mapped controller.
The capture part has been left out for now, and will be added eventually.
Signed-off-by: Emilio López <emilio@elopez.com.ar>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
