| Age | Commit message (Collapse) | Author |
|---|
|
parameter
On Fireworks board module of Echo Audio, TSB43Cx43A (IceLynx Micro, iCEM)
is used to process payload of isochronous packets. There's an public
document of this chip[1]. This document is for firmware programmers to
transfer/receive AMDTP with IEC60958 data format, however in clause 2.5,
2.6 and 2.7, we can see system design to utilize the sequence of value in
SYT field of CIP header. In clause 2.3, we can see the specification of
Audio Master Clock (MCLK) from iCEM.
Well, this clock is actually not used for sampling clock. This can be
confirmed when corresponding driver transfer random value as the sequence
of SYT field. Even if in this case, the unit generates proper sound.
Additionally, in unique command set for this board module, the format
of CIP is changed; for IEC 61883-6 mode which we use, and for Windows
Operating System. In the latter mode, the whole 32 bit field in second CIP
header from Windows driver is used to represent counter of packets (NO-DATA
code is still used for packets without data blocks). If the master clock
was physically used by DSP on the board module, the Windows driver must
have transferred correct sequence of SYT field.
Furthermore, as long as seeing capacities of AudioFire2, AudioFire4,
AudioFire8, AudioFirePre8 and AudioFire12, these models don't support
SYT-Match clock source.
Summary, we have no need to relate incoming/outgoing packets. This commit
drops reusing SYT sequence of incoming packets for outgoing packets.
[1] Using TSB43Cx43A: S/PDIF over 1394 (2003, Texus Instruments
Incorporated)
http://www.ti.com/analog/docs/litabsmultiplefilelist.tsp?literatureNumber=slla148&docCategoryId=1&familyId=361
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
When some fireworks units are connected sequentially, userspace
applications are involved at bus-reset state on IEEE 1394 bus. In the
state, any communications can be canceled. Therefore, sound card
registration should be delayed till the bus gets calm.
This commit achieves it.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Currently, model-specific quirks are detected out of information parser,
however it's natural to detect it in the parser.
This commit applies the idea.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
In IEC 61883-1, at bus-reset, applications can continue isochronous
streaming by updating connections. In ALSA fireworks driver, the
operation is executed in 'update' handler for bus driver.
The connection resources are also changed in process contexts of PCM/MIDI
applications. Therefore, bus-reset handling has race condition
against connection. Current ALSA fireworks driver has a bug for the
condition.
This commit fixes the bug, by expand critical section with mutex. As a
result, connection updating operation in bus-reset handler and connection
changing operation in process context are serialized.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The counter is incremented/decremented in critical section protected with
mutex. Therefore, no need to use atomic_t.
This commit changes the type to unsigned int.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Currently, critical section is protected by mutex in functions of
fireworks_stream.c. Callers increments/decrements substreams counter
before calling the functions. Moving mutex to the callers code allows
to change type of the substeram counter from atomic_t to unsigned int.
This commit is a preparation for obsoleting usage of atomic_t for
substream counter.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
In former commit, snd_efw_command_get_phys_meters() was added to handle
metering data. The given buffer is used to save transaction result and to
convert between endianness. But this causes sparse warnings.
fireworks_command.c:269:25: warning: incorrect type in argument 1 (different base types)
fireworks_command.c:269:25: expected unsigned int [usertype] *p
fireworks_command.c:269:25: got restricted __be32 [usertype] *
This commit fixes this bug.
Fixes: bde8a8f23bbe('ALSA: fireworks: Add transaction and some commands')
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
When committed to upstream, these four modules had wrong entries for
Makefile. This forces them to be loadable modules even if they're set
as built-in.
This commit fixes this bug.
Fixes: b5b04336015e('ALSA: fireworks: Add skelton for Fireworks based devices')
Fixes: fd6f4b0dc167('ALSA: bebob: Add skelton for BeBoB based devices')
Fixes: 1a4e39c2e5ca('ALSA: oxfw: Move to its own directory')
Fixes: 14ff6a094815('ALSA: dice: Move file to its own directory')
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This commit renames some macros just related to AM824 format. In later
commit, they're moved to AM824 layer.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Setting the format of PCM substream to AMDTP stream structure is important
to set a handler to copy actual PCM samples between buffers. The
processing should be in data block processing layer because essentially
it has no relationship to packet streaming.
This commit renames PCM format setting function to prepare for integrating
AM824 layer.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
In IEC 61883-6, MIDI messages are transferred in MIDI conformant data
channel. Essentially, packet streaming layer is not responsible for MIDI
functionality.
This commit moves MIDI trigger helper function from the layer to AM824
layer. The rest of codes related to MIDI functionality will be moved in
later commits.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
In IEC 61883-6, PCM frames are transferred in Multi Bit Linear Audio data
channel. The data channel transfers 16/20/24 bit PCM samples. Thus, PCM
substream has a constrain about it.
This commit moves codes related to the constraint from packet streaming
layer to AM824 data block processing layer.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The value of FDF field in CIP header is protocol-dependent. Thus, it's
better to allow data block processing layer to decide the value in any
timing.
In AM824 data format, the value of FDF field in CIP header indicates
N-flag and Nominal Sampling Frequency Code (sfc). The N-flag is for
switching 'Clock-based rate control mode' and 'Command-based rate control
mode'. In our implementation, 'Clock-based rate control mode' is just
supported. Therefore, When sampling transfer frequency is decided, then
the FDF can be set.
This commit replaces 'amdtp_stream_set_parameters' with
'amdtp_am824_set_parameters' to set the FDF. This is the same timing
to decide the ration between the number of data blocks and the number of
PCM frames.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This commit adds data block processing layer for AM824 format. The new
layer initializes streaming layer with its value for fmt field.
Currently, most implementation of data block processing still remains
streaming layer. In later commits, these codes will be moved to the layer.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
functional separation
In later commit, data block processing layer will be newly added. This
layer will be named as 'amdtp-am824'.
This commit renames current amdtp file to amdtp-stream, to distinguish it
from the new layer.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
In IEC 61883-6, one data block represents one event. In ALSA, the event is
one PCM frame. Therefore, when processing one data block, current
implementation counts one PCM frame.
On the other hand, Dice platform has a quirk called as 'dual wire' at
higher sampling rate. In detail, see comment of commit 6eb6c81eee2a
("ALSA: dice: Split stream functionality into a file").
Currently, to handle this quirk, AMDTP stream structure has a
'double_pcm_frames' member. When this is enabled, two PCM frames are
counted. Each driver set this flag by accessing the structure member
directly.
In future commit, some members related to AM824 data block will be moved
to specific structure, to separate packet streaming layer and data block
processing layer. The access will be limited by opaque pointer.
For this reason, this commit adds an argument into
amdtp_stream_set_parameter() to set the flag.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
detects error
Currently, amdtp_stream_set_parameters() returns no error even if wrong
arguments are given. This is not good for streaming layer because drivers
can continue processing ignoring capability of streaming layer.
This commit changes this function to return error code.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
In PCM core, when hw_params() in each driver returns error, the state of
PCM substream is kept as 'open'. In this case, current drivers for sound
units on IEEE 1394 bus doesn't decrement substream counter in hw_free()
correctly. This causes these drivers to keep streams even if not
required.
This commit fixes this bug. When snd_pcm_lib_alloc_vmalloc_buffer()
fails, hw_params function in each driver returns without incrementing the
counter.
Reported-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Fireworks uses TSB43CB43(IceLynx-Micro) as its IEC 61883-1/6 interface.
This chip includes ARM7 core, and loads and runs program. The firmware
is stored in on-board memory and loaded every powering-on from it.
Echo Audio ships several versions of firmwares for each model. These
firmwares have each quirk and the quirk changes a sequence of packets.
As long as I investigated, AudioFire2/AudioFire4/AudioFirePre8 have a
quirk to transfer a first packet with 0x02 in its dbc field. This causes
ALSA Fireworks driver to detect discontinuity. In this case, firmware
version 5.7.0, 5.7.3 and 5.8.0 are used.
Payload CIP CIP
quadlets header1 header2
02 00050002 90ffffff <-
42 0005000a 90013000
42 00050012 90014400
42 0005001a 90015800
02 0005001a 90ffffff
42 00050022 90019000
42 0005002a 9001a400
42 00050032 9001b800
02 00050032 90ffffff
42 0005003a 9001d000
42 00050042 9001e400
42 0005004a 9001f800
02 0005004a 90ffffff
(AudioFire2 with firmware version 5.7.)
$ dmesg
snd-fireworks fw1.0: Detect discontinuity of CIP: 00 02
These models, AudioFire8 (since Jul 2009 ) and Gibson Robot Interface
Pack series uses the same ARM binary as their firmware. Thus, this
quirk may be observed among them.
This commit adds a new member for AMDTP structure. This member represents
the value of dbc field in a first AMDTP packet. Drivers can set it with
a preferred value according to model's quirk.
Tested-by: Johannes Oertei <johannes.oertel@uni-due.de>
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This reverts commit 9c6893e0be38b6ca9a56a854226e51dee0a16a5a.
The fix is superseded by the next commit as a better implementation
for supporting AudioFire2/AudioFire4/AudioFirePre8 quirks.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Fireworks uses TSB43CB43(IceLynx-Micro) as its IEC 61883-1/6 interface.
This chip includes ARM7 core, and loads and runs program. The firmware
is stored in on-board memory and loaded every powering-on.
Echo Audio ships several versions of firmwares for each model. These
firmwares have each quirk and the quirk changes a sequence of packets.
AudioFire2 has a quirk to transfer a first packet with non-zero in
its dbc field. This causes ALSA Fireworks driver to detect discontinuity.
As long as I investigated, firmware 5.7, 5.7.6 and 5.8 have this quirk.
This commit adds a support for the quirk to handle AudioFire2 packets.
For safe, CIP_SKIP_INIT_DBC_CHECK is applied to all versions of
AudioFire2's firmwares.
02 00050002 90ffffff <-
42 0005000a 90013000
42 00050012 90014400
42 0005001a 90015800
02 0005001a 90ffffff
42 00050022 90019000
42 0005002a 9001a400
42 00050032 9001b800
02 00050032 90ffffff
42 0005003a 9001d000
42 00050042 9001e400
42 0005004a 9001f800
02 0005004a 90ffffff
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Change 'propper' to 'proper'
Change 'paramters' to 'parameters'
Change 'SYT_INTEVAL' to 'SYT_INTERVAL'
Change 'aligh'/'alighed' to 'align'/'aligned'
Signed-off-by: Yannick Guerrini <yguerrini@tomshardware.fr>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
A part of these drivers, especially BeBoB driver, are programmed to wait
some events. Thus the drivers should not destroy any data in .remove()
context.
This commit moves some destructors from 'struct fw_driver.remove()' to
'struct snd_card.private_free()' to shutdown safely.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Cc: <stable@vger.kernel.org> # 3.19+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Currently stream destructor in each driver has a problem to be called in
a context in which sound card object is released, because the destructors
call amdtp_stream_pcm_abort() and touch PCM runtime data.
The PCM runtime data is destroyed in application's context with
snd_pcm_close(), on the other hand PCM substream data is destroyed after
sound card object is released, in most case after all of ALSA character
devices are released. When PCM runtime is destroyed and PCM substream is
remained, amdtp_stream_pcm_abort() touches PCM runtime data and causes
Null-pointer-dereference.
This commit changes stream destructors and allows each driver to call
it after releasing runtime.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Cc: <stable@vger.kernel.org> # 3.19+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Fireworks and Dice drivers try to touch instances of FireWire unit after
sound card object is released, while references to the unit is decremented
in .remove(). When unplugging during streaming, sound card object is
released after .remove(), thus Fireworks and Dice drivers causes GPF or
Null-pointer-dereferencing to application processes because an instance of
FireWire unit was already released.
This commit adds reference-counting for FireWire unit in drivers to allow
them to touch an instance of FireWire unit after .remove(). In most case,
any operations after .remove() may be failed safely.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Cc: <stable@vger.kernel.org> # 3.19+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
There are several devices that expect to receive MIDI data only in the
first eight data blocks of a packet. If the driver restricts the data
rate to the allowed rate (as mandated by the specification, but not yet
implemented by this driver), this happens naturally. Therefore, there
is no reason to ever try to use more data packets with any device.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Tested-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Although the 't->length' is a big-endian value, it's used without any
conversion. This means that the driver always uses 'length' parameter.
Fixes: 555e8a8f7f14("ALSA: fireworks: Add command/response functionality into hwdep interface")
Reported-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Use %d for loop counter and %X for device capabilities. This is a
supplemental patch for Hans Wennborg's patch.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Signed-off-by: Hans Wennborg <hans@hanshq.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Currently mutex_destroy() is called in module's cleanup function. But after
cleaned up, this mutex is automatically released. So this function call
is meaningless.
[fixed a typo in changelog by tiwai]
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The constants of enum snd_efw_grp_type is for struct snd_efw_phys_grp.type.
But this member is 1 byte. Although the value is between 0x00-0xff, a constant
has 0x10000. This constant is meaningless.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
It includes descriptions to cause misreading.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
To reverse a pointer for the ring buffer, subtraction by buffer
size is better than assignment to the beginning of the buffer.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
All assignment for local variables in these functions are not related to
critical section.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
There was a typo here so we return directly instead of freeing "hwinfo".
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewd-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Tested-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
We checked "err" earlier. These things seem to be left over code.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewd-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Tested-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
According to coding rule.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This commit adds suffix to register values of each device, to supress 'sparse'
warnings. Additionally, this commit changes offset values with integer literal.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The second argument of snd_efw_command_get_sampling_rate() means sampling
rate and its type is 'unsigned int'. But 'int' variable is passed as parameter.
It's better to apply the same type for the variable as its argument.
Similally, the type of variable for snd_efw_command_get_clock_source() and
avc_bridgeco_get_plug_type() should be the same type as each argument.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Originally, I intent to this argument given with 'struct snd_pcm_runtime.rate'
or params_rate(). They return value of 'unsigned int'. So 'unsigned int' is
better for the type of this argument.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
There are two modes for Fireworks, IEC 61883 compliant or Windows.
So it's better to use enum type instead of int to express the intension,
even if C language specification defines to handle enum variables as usual
integer.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The return value of memdup_user() should be passed to return correct error.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This commit adds two functionality for hwdep interface, adds two parameters for
this driver, add a node for proc interface.
To receive responses from devices, this driver already allocate own callback
into initial memory space in host controller. This means no one can allocate
its own callback to the address. So this driver must give a way for user
applications to receive responses.
This commit adds a functionality to receive responses via hwdep interface. The
application can receive responses to read from this interface. To achieve this,
this commit adds a buffer to queue responses. The default size of this buffer is
1024 bytes. This size can be changed to give preferrable size to
'resp_buf_size' parameter for this driver. The application should notice rest
of space in this buffer because this driver don't push responses when this
buffer has no space.
Additionaly, this commit adds a functionality to transmit commands via hwdep
interface. The application can transmit commands to write into this interface.
I note that the application can transmit one command at once, but can receive
as many responses as possible untill the user-buffer is full.
When using these interfaces, the application must keep maximum number of
sequence number in command within the number in firewire.h because this driver
uses this number to distinguish the response is against the command by the
application or this driver.
Usually responses against commands which the application transmits are pushed
into this buffer. But to enable 'resp_buf_debug' parameter for this driver, all
responses are pushed into the buffer. When using this mode, I reccomend to
expand the size of buffer.
Finally this commit adds a new node into proc interface to output status of the
buffer.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This interface is designed for mixer/control application. To use hwdep
interface, the application can get information about firewire node, can
lock/unlock kernel streaming and can get notification at starting/stopping
kernel streaming.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This commit adds a functionality to capture/playback PCM samples.
When AMDTP stream is already running for PCM or the source of clock is not
internal, available sampling rate is limited at current one.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Fireworks has a quirk to ignore MIDI messages in data blocks more than 8.
This commit adds a flag for this quirk and codes to skip 8 or more data
blocks to transfer MIDI messages.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This commit adds a functionality to capture/playback MIDI messages.
When no AMDTP streams are running, this driver starts AMDTP stream for MIDI
stream at current sampling rate.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This commit adds proc interface to output infomation for debugging.
- firmware information
- sampling rate and clock source
- physical metering (linear value)
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
reset
Fireworks has a quirk to reset data block counter at bus reset.
This commit adds a flag of CIP_SKIP_DBC_ZERO_CHECK. This flag has an effect
to skip checking dbc continuity when dbc is zero.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Fireworks firmware version 5.5 reports fix interval for dbc in each packet.
For example, AudioFire4:
CIP0 CIP1 Payload
00070000 900484FF 72
00070008 9004A8FF 72
00070008 90FFFFFF 02
00070010 9004D0FF 72
00070018 9004C4FF 72
00070020 9004E8FF 72
00070020 90FFFFFF 02
00070028 900410FE 72
The interval of each dbc should be 16 except for empty packet but it's still 8.
This commit adds a flag for this quirk and codes to refer to a fixed value.
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
