| Age | Commit message (Collapse) | Author |
|---|
|
Pull ceph fixes from Ilya Dryomov:
"Three important fixes tagged for stable (an indefinite hang, a crash
on an assert and a NULL pointer dereference) plus a small series from
Luis fixing instances of vfree() under spinlock"
* tag 'ceph-for-5.3-rc6' of git://github.com/ceph/ceph-client:
libceph: fix PG split vs OSD (re)connect race
ceph: don't try fill file_lock on unsuccessful GETFILELOCK reply
ceph: clear page dirty before invalidate page
ceph: fix buffer free while holding i_ceph_lock in fill_inode()
ceph: fix buffer free while holding i_ceph_lock in __ceph_build_xattrs_blob()
ceph: fix buffer free while holding i_ceph_lock in __ceph_setxattr()
libceph: allow ceph_buffer_put() to receive a NULL ceph_buffer
|
|
We can't rely on ->peer_features in calc_target() because it may be
called both when the OSD session is established and open and when it's
not. ->peer_features is not valid unless the OSD session is open. If
this happens on a PG split (pg_num increase), that could mean we don't
resend a request that should have been resent, hanging the client
indefinitely.
In userspace this was fixed by looking at require_osd_release and
get_xinfo[osd].features fields of the osdmap. However these fields
belong to the OSD section of the osdmap, which the kernel doesn't
decode (only the client section is decoded).
Instead, let's drop this feature check. It effectively checks for
luminous, so only pre-luminous OSDs would be affected in that on a PG
split the kernel might resend a request that should not have been
resent. Duplicates can occur in other scenarios, so both sides should
already be prepared for them: see dup/replay logic on the OSD side and
retry_attempt check on the client side.
Cc: stable@vger.kernel.org
Fixes: 7de030d6b10a ("libceph: resend on PG splits if OSD has RESEND_ON_SPLIT")
Link: https://tracker.ceph.com/issues/41162
Reported-by: Jerry Lee <leisurelysw24@gmail.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Tested-by: Jerry Lee <leisurelysw24@gmail.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
|
|
This patch adds initial support for offloading basechains using the
priority range from 1 to 65535. This is restricting the netfilter
priority range to 16-bit integer since this is what most drivers assume
so far from tc. It should be possible to extend this range of supported
priorities later on once drivers are updated to support for 32-bit
integer priorities.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth
Johan Hedberg says:
====================
pull request: bluetooth 2019-08-17
Here's a set of Bluetooth fixes for the 5.3-rc series:
- Multiple fixes for Qualcomm (btqca & hci_qca) drivers
- Minimum encryption key size debugfs setting (this is required for
Bluetooth Qualification)
- Fix hidp_send_message() to have a meaningful return value
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For testing and qualification purposes it is useful to allow changing
the minimum encryption key size value that the host stack is going to
enforce. This adds a new debugfs setting min_encrypt_key_size to achieve
this functionality.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
This commit eliminates the use of the link 'stale_limit' & 'prev_from'
(besides the already removed - 'stale_cnt') variables in the detection
of repeated retransmit failures as there is no proper way to initialize
them to avoid a false detection, i.e. it is not really a retransmission
failure but due to a garbage values in the variables.
Instead, a jiffies variable will be added to individual skbs (like the
way we restrict the skb retransmissions) in order to mark the first skb
retransmit time. Later on, at the next retransmissions, the timestamp
will be checked to see if the skb in the link transmq is "too stale",
that is, the link tolerance time has passed, so that a link reset will
be ordered. Note, just checking on the first skb in the queue is fine
enough since it must be the oldest one.
A counter is also added to keep track the actual skb retransmissions'
number for later checking when the failure happens.
The downside of this approach is that the skb->cb[] buffer is about to
be exhausted, however it is always able to allocate another memory area
and keep a reference to it when needed.
Fixes: 77cf8edbc0e7 ("tipc: simplify stale link failure criteria")
Reported-by: Hoang Le <hoang.h.le@dektech.com.au>
Acked-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
David Howells says:
====================
rxrpc: Fix local endpoint handling
Here's a pair of patches that fix two issues in the handling of local
endpoints (rxrpc_local structs):
(1) Use list_replace_init() rather than list_replace() if we're going to
unconditionally delete the replaced item later, lest the list get
corrupted.
(2) Don't access the rxrpc_local object after passing our ref to the
workqueue, not even to illuminate tracepoints, as the work function
may cause the object to be freed. We have to cache the information
beforehand.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
This patchset contains Netfilter fixes for net:
1) Extend selftest to cover flowtable with ipsec, from Florian Westphal.
2) Fix interaction of ipsec with flowtable, also from Florian.
3) User-after-free with bound set to rule that fails to load.
4) Adjust state and timeout for flows that expire.
5) Timeout update race with flows in teardown state.
6) Ensure conntrack id hash calculation use invariants as input,
from Dirk Morris.
7) Do not push flows into flowtable for TCP fin/rst packets.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
packet_sendmsg() checks tx_ring.pg_vec to decide
if it must call tpacket_snd().
Problem is that the check is lockless, meaning another thread
can issue a concurrent setsockopt(PACKET_TX_RING ) to flip
tx_ring.pg_vec back to NULL.
Given that tpacket_snd() grabs pg_vec_lock mutex, we can
perform the check again to solve the race.
syzbot reported :
kasan: CONFIG_KASAN_INLINE enabled
kasan: GPF could be caused by NULL-ptr deref or user memory access
general protection fault: 0000 [#1] PREEMPT SMP KASAN
CPU: 1 PID: 11429 Comm: syz-executor394 Not tainted 5.3.0-rc4+ #101
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:packet_lookup_frame+0x8d/0x270 net/packet/af_packet.c:474
Code: c1 ee 03 f7 73 0c 80 3c 0e 00 0f 85 cb 01 00 00 48 8b 0b 89 c0 4c 8d 24 c1 48 b8 00 00 00 00 00 fc ff df 4c 89 e1 48 c1 e9 03 <80> 3c 01 00 0f 85 94 01 00 00 48 8d 7b 10 4d 8b 3c 24 48 b8 00 00
RSP: 0018:ffff88809f82f7b8 EFLAGS: 00010246
RAX: dffffc0000000000 RBX: ffff8880a45c7030 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 1ffff110148b8e06 RDI: ffff8880a45c703c
RBP: ffff88809f82f7e8 R08: ffff888087aea200 R09: fffffbfff134ae50
R10: fffffbfff134ae4f R11: ffffffff89a5727f R12: 0000000000000000
R13: 0000000000000001 R14: ffff8880a45c6ac0 R15: 0000000000000000
FS: 00007fa04716f700(0000) GS:ffff8880ae900000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007fa04716edb8 CR3: 0000000091eb4000 CR4: 00000000001406e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
packet_current_frame net/packet/af_packet.c:487 [inline]
tpacket_snd net/packet/af_packet.c:2667 [inline]
packet_sendmsg+0x590/0x6250 net/packet/af_packet.c:2975
sock_sendmsg_nosec net/socket.c:637 [inline]
sock_sendmsg+0xd7/0x130 net/socket.c:657
___sys_sendmsg+0x3e2/0x920 net/socket.c:2311
__sys_sendmmsg+0x1bf/0x4d0 net/socket.c:2413
__do_sys_sendmmsg net/socket.c:2442 [inline]
__se_sys_sendmmsg net/socket.c:2439 [inline]
__x64_sys_sendmmsg+0x9d/0x100 net/socket.c:2439
do_syscall_64+0xfd/0x6a0 arch/x86/entry/common.c:296
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Fixes: 69e3c75f4d54 ("net: TX_RING and packet mmap")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ctx->sk_write_space pointer is only set when TLS tx mode is enabled.
When running without TX mode its a null pointer but we still set the
sk sk_write_space pointer on close().
Fix the close path to only overwrite sk->sk_write_space when the current
pointer is to the tls_write_space function indicating the tls module should
clean it up properly as well.
Reported-by: Hillf Danton <hdanton@sina.com>
Cc: Ying Xue <ying.xue@windriver.com>
Cc: Andrey Konovalov <andreyknvl@google.com>
Fixes: 57c722e932cfb ("net/tls: swap sk_write_space on close")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
rxrpc_queue_local() attempts to queue the local endpoint it is given and
then, if successful, prints a trace line. The trace line includes the
current usage count - but we're not allowed to look at the local endpoint
at this point as we passed our ref on it to the workqueue.
Fix this by reading the usage count before queuing the work item.
Also fix the reading of local->debug_id for trace lines, which must be done
with the same consideration as reading the usage count.
Fixes: 09d2bf595db4 ("rxrpc: Add a tracepoint to track rxrpc_local refcounting")
Reported-by: syzbot+78e71c5bab4f76a6a719@syzkaller.appspotmail.com
Signed-off-by: David Howells <dhowells@redhat.com>
|
|
When a local endpoint (struct rxrpc_local) ceases to be in use by any
AF_RXRPC sockets, it starts the process of being destroyed, but this
doesn't cause it to be removed from the namespace endpoint list immediately
as tearing it down isn't trivial and can't be done in softirq context, so
it gets deferred.
If a new socket comes along that wants to bind to the same endpoint, a new
rxrpc_local object will be allocated and rxrpc_lookup_local() will use
list_replace() to substitute the new one for the old.
Then, when the dying object gets to rxrpc_local_destroyer(), it is removed
unconditionally from whatever list it is on by calling list_del_init().
However, list_replace() doesn't reset the pointers in the replaced
list_head and so the list_del_init() will likely corrupt the local
endpoints list.
Fix this by using list_replace_init() instead.
Fixes: 730c5fd42c1e ("rxrpc: Fix local endpoint refcounting")
Reported-by: syzbot+193e29e9387ea5837f1d@syzkaller.appspotmail.com
Signed-off-by: David Howells <dhowells@redhat.com>
|
|
TCP rst and fin packets do not qualify to place a flow into the
flowtable. Most likely there will be no more packets after connection
closure. Without this patch, this flow entry expires and connection
tracking picks up the entry in ESTABLISHED state using the fixup
timeout, which makes this look inconsistent to the user for a connection
that is actually already closed.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
If the stream outq is not empty, need to kfree nstr_list.
Fixes: d570a59c5b5f ("sctp: only allow the out stream reset when the stream outq is empty")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
|
|
As the annotation says in sctp_do_8_2_transport_strike():
"If the transport error count is greater than the pf_retrans
threshold, and less than pathmaxrtx ..."
It should be transport->error_count checked with pathmaxrxt,
instead of asoc->pf_retrans.
Fixes: 5aa93bcf66f4 ("sctp: Implement quick failover draft from tsvwg")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
|
|
Change ct id hash calculation to only use invariants.
Currently the ct id hash calculation is based on some fields that can
change in the lifetime on a conntrack entry in some corner cases. The
current hash uses the whole tuple which contains an hlist pointer which
will change when the conntrack is placed on the dying list resulting in
a ct id change.
This patch also removes the reply-side tuple and extension pointer from
the hash calculation so that the ct id will will not change from
initialization until confirmation.
Fixes: 3c79107631db1f7 ("netfilter: ctnetlink: don't use conntrack/expect object addresses as id")
Signed-off-by: Dirk Morris <dmorris@metaloft.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Let hidp_send_message return the number of successfully queued bytes
instead of an unconditional 0.
With the return value fixed to 0, other drivers relying on hidp, such as
hidraw, can not return meaningful values from their respective
implementations of write(). In particular, with the current behavior, a
hidraw device's write() will have different return values depending on
whether the device is connected via USB or Bluetooth, which makes it
harder to abstract away the transport layer.
Signed-off-by: Fabian Henneke <fabian.henneke@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
We set the field 'addr_trial_end' to 'jiffies', instead of the current
value 0, at the moment the node address is initialized. This guarantees
we don't inadvertently enter an address trial period when the node
address is explicitly set by the user.
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The dsa framework has optional .port_mdb_{prepare,add,del} callback fields
for drivers to handle multicast database entries. When adding an entry, the
framework goes through a prepare phase, then a commit phase. Drivers not
providing these callbacks should be detected in the prepare phase.
DSA core may still bypass the bridge layer and call the dsa_port_mdb_add
function directly with no prepare phase or no switchdev trans object,
and the framework ends up calling an undefined .port_mdb_add callback.
This results in a NULL pointer dereference, as shown in the log below.
The other functions seem to be properly guarded. Do the same for
.port_mdb_add in dsa_switch_mdb_add_bitmap() as well.
8<--- cut here ---
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = (ptrval)
[00000000] *pgd=00000000
Internal error: Oops: 80000005 [#1] SMP ARM
Modules linked in: rtl8xxxu rtl8192cu rtl_usb rtl8192c_common rtlwifi mac80211 cfg80211
CPU: 1 PID: 134 Comm: kworker/1:2 Not tainted 5.3.0-rc1-00247-gd3519030752a #1
Hardware name: Allwinner sun7i (A20) Family
Workqueue: events switchdev_deferred_process_work
PC is at 0x0
LR is at dsa_switch_event+0x570/0x620
pc : [<00000000>] lr : [<c08533ec>] psr: 80070013
sp : ee871db8 ip : 00000000 fp : ee98d0a4
r10: 0000000c r9 : 00000008 r8 : ee89f710
r7 : ee98d040 r6 : ee98d088 r5 : c0f04c48 r4 : ee98d04c
r3 : 00000000 r2 : ee89f710 r1 : 00000008 r0 : ee98d040
Flags: Nzcv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
Control: 10c5387d Table: 6deb406a DAC: 00000051
Process kworker/1:2 (pid: 134, stack limit = 0x(ptrval))
Stack: (0xee871db8 to 0xee872000)
1da0: ee871e14 103ace2d
1dc0: 00000000 ffffffff 00000000 ee871e14 00000005 00000000 c08524a0 00000000
1de0: ffffe000 c014bdfc c0f04c48 ee871e98 c0f04c48 ee9e5000 c0851120 c014bef0
1e00: 00000000 b643aea2 ee9b4068 c08509a8 ee2bf940 ee89f710 ee871ecb 00000000
1e20: 00000008 103ace2d 00000000 c087e248 ee29c868 103ace2d 00000001 ffffffff
1e40: 00000000 ee871e98 00000006 00000000 c0fb2a50 c087e2d0 ffffffff c08523c4
1e60: ffffffff c014bdfc 00000006 c0fad2d0 ee871e98 ee89f710 00000000 c014c500
1e80: 00000000 ee89f3c0 c0f04c48 00000000 ee9e5000 c087dfb4 ee9e5000 00000000
1ea0: ee89f710 ee871ecb 00000001 103ace2d 00000000 c0f04c48 00000000 c087e0a8
1ec0: 00000000 efd9a3e0 0089f3c0 103ace2d ee89f700 ee89f710 ee9e5000 00000122
1ee0: 00000100 c087e130 ee89f700 c0fad2c8 c1003ef0 c087de4c 2e928000 c0fad2ec
1f00: c0fad2ec ee839580 ef7a62c0 ef7a9400 00000000 c087def8 c0fad2ec c01447dc
1f20: ef315640 ef7a62c0 00000008 ee839580 ee839594 ef7a62c0 00000008 c0f03d00
1f40: ef7a62d8 ef7a62c0 ffffe000 c0145b84 ffffe000 c0fb2420 c0bfaa8c 00000000
1f60: ffffe000 ee84b600 ee84b5c0 00000000 ee870000 ee839580 c0145b40 ef0e5ea4
1f80: ee84b61c c014a6f8 00000001 ee84b5c0 c014a5b0 00000000 00000000 00000000
1fa0: 00000000 00000000 00000000 c01010e8 00000000 00000000 00000000 00000000
1fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1fe0: 00000000 00000000 00000000 00000000 00000013 00000000 00000000 00000000
[<c08533ec>] (dsa_switch_event) from [<c014bdfc>] (notifier_call_chain+0x48/0x84)
[<c014bdfc>] (notifier_call_chain) from [<c014bef0>] (raw_notifier_call_chain+0x18/0x20)
[<c014bef0>] (raw_notifier_call_chain) from [<c08509a8>] (dsa_port_mdb_add+0x48/0x74)
[<c08509a8>] (dsa_port_mdb_add) from [<c087e248>] (__switchdev_handle_port_obj_add+0x54/0xd4)
[<c087e248>] (__switchdev_handle_port_obj_add) from [<c087e2d0>] (switchdev_handle_port_obj_add+0x8/0x14)
[<c087e2d0>] (switchdev_handle_port_obj_add) from [<c08523c4>] (dsa_slave_switchdev_blocking_event+0x94/0xa4)
[<c08523c4>] (dsa_slave_switchdev_blocking_event) from [<c014bdfc>] (notifier_call_chain+0x48/0x84)
[<c014bdfc>] (notifier_call_chain) from [<c014c500>] (blocking_notifier_call_chain+0x50/0x68)
[<c014c500>] (blocking_notifier_call_chain) from [<c087dfb4>] (switchdev_port_obj_notify+0x44/0xa8)
[<c087dfb4>] (switchdev_port_obj_notify) from [<c087e0a8>] (switchdev_port_obj_add_now+0x90/0x104)
[<c087e0a8>] (switchdev_port_obj_add_now) from [<c087e130>] (switchdev_port_obj_add_deferred+0x14/0x5c)
[<c087e130>] (switchdev_port_obj_add_deferred) from [<c087de4c>] (switchdev_deferred_process+0x64/0x104)
[<c087de4c>] (switchdev_deferred_process) from [<c087def8>] (switchdev_deferred_process_work+0xc/0x14)
[<c087def8>] (switchdev_deferred_process_work) from [<c01447dc>] (process_one_work+0x218/0x50c)
[<c01447dc>] (process_one_work) from [<c0145b84>] (worker_thread+0x44/0x5bc)
[<c0145b84>] (worker_thread) from [<c014a6f8>] (kthread+0x148/0x150)
[<c014a6f8>] (kthread) from [<c01010e8>] (ret_from_fork+0x14/0x2c)
Exception stack(0xee871fb0 to 0xee871ff8)
1fa0: 00000000 00000000 00000000 00000000
1fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
1fe0: 00000000 00000000 00000000 00000000 00000013 00000000
Code: bad PC value
---[ end trace 1292c61abd17b130 ]---
[<c08533ec>] (dsa_switch_event) from [<c014bdfc>] (notifier_call_chain+0x48/0x84)
corresponds to
$ arm-linux-gnueabihf-addr2line -C -i -e vmlinux c08533ec
linux/net/dsa/switch.c:156
linux/net/dsa/switch.c:178
linux/net/dsa/switch.c:328
Fixes: e6db98db8a95 ("net: dsa: add switch mdb bitmap functions")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix rxrpc_unuse_local() to handle a NULL local pointer as it can be called
on an unbound socket on which rx->local is not yet set.
The following reproduced (includes omitted):
int main(void)
{
socket(AF_RXRPC, SOCK_DGRAM, AF_INET);
return 0;
}
causes the following oops to occur:
BUG: kernel NULL pointer dereference, address: 0000000000000010
...
RIP: 0010:rxrpc_unuse_local+0x8/0x1b
...
Call Trace:
rxrpc_release+0x2b5/0x338
__sock_release+0x37/0xa1
sock_close+0x14/0x17
__fput+0x115/0x1e9
task_work_run+0x72/0x98
do_exit+0x51b/0xa7a
? __context_tracking_exit+0x4e/0x10e
do_group_exit+0xab/0xab
__x64_sys_exit_group+0x14/0x17
do_syscall_64+0x89/0x1d4
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Reported-by: syzbot+20dee719a2e090427b5f@syzkaller.appspotmail.com
Fixes: 730c5fd42c1e ("rxrpc: Fix local endpoint refcounting")
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Jeffrey Altman <jaltman@auristor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that we swap the original proto and clear the ULP pointer
on close we have to make sure no callback will try to access
the freed state. sk_write_space is not part of sk_prot, remember
to swap it.
Reported-by: syzbot+dcdc9deefaec44785f32@syzkaller.appspotmail.com
Fixes: 95fa145479fb ("bpf: sockmap/tls, close can race with map free")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Generating and retrieving socket cookies are a useful feature that is
exposed to BPF for various program types through bpf_get_socket_cookie()
helper.
The fact that the cookie counter is per netns is quite a limitation
for BPF in practice in particular for programs in host namespace that
use socket cookies as part of a map lookup key since they will be
causing socket cookie collisions e.g. when attached to BPF cgroup hooks
or cls_bpf on tc egress in host namespace handling container traffic
from veth or ipvlan devices with peer in different netns. Change the
counter to be global instead.
Socket cookie consumers must assume the value as opqaue in any case.
Not every socket must have a cookie generated and knowledge of the
counter value itself does not provide much value either way hence
conversion to global is fine.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Martynas Pumputis <m@lambda.lt>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Don't bother generating maxSkew in the ACK packet as it has been obsolete
since AFS 3.1.
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Jeffrey Altman <jaltman@auristor.com>
|
|
The object lifetime management on the rxrpc_local struct is broken in that
the rxrpc_local_processor() function is expected to clean up and remove an
object - but it may get requeued by packets coming in on the backing UDP
socket once it starts running.
This may result in the assertion in rxrpc_local_rcu() firing because the
memory has been scheduled for RCU destruction whilst still queued:
rxrpc: Assertion failed
------------[ cut here ]------------
kernel BUG at net/rxrpc/local_object.c:468!
Note that if the processor comes around before the RCU free function, it
will just do nothing because ->dead is true.
Fix this by adding a separate refcount to count active users of the
endpoint that causes the endpoint to be destroyed when it reaches 0.
The original refcount can then be used to refcount objects through the work
processor and cause the memory to be rcu freed when that reaches 0.
Fixes: 4f95dd78a77e ("rxrpc: Rework local endpoint management")
Reported-by: syzbot+1e0edc4b8b7494c28450@syzkaller.appspotmail.com
Signed-off-by: David Howells <dhowells@redhat.com>
|
|
Flows that are in teardown state (due to RST / FIN TCP packet) still
have their offload flag set on. Hence, the conntrack garbage collector
may race to undo the timeout adjustment that the fixup routine performs,
leaving the conntrack entry in place with the internal offload timeout
(one day).
Update teardown flow state to ESTABLISHED and set tracking to liberal,
then once the offload bit is cleared, adjust timeout if it is more than
the default fixup timeout (conntrack might already have set a lower
timeout from the packet path).
Fixes: da5984e51063 ("netfilter: nf_flow_table: add support for sending flows back to the slow path")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Update conntrack entry to pick up expired flows, otherwise the conntrack
entry gets stuck with the internal offload timeout (one day). The TCP
state also needs to be adjusted to ESTABLISHED state and tracking is set
to liberal mode in order to give conntrack a chance to pick up the
expired flow.
Fixes: ac2a66665e23 ("netfilter: add generic flow table infrastructure")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
If a rule that has already a bound anonymous set fails to be added, the
preparation phase releases the rule and the bound set. However, the
transaction object from the abort path still has a reference to the set
object that is stale, leading to a use-after-free when checking for the
set->bound field. Add a new field to the transaction that specifies if
the set is bound, so the abort path can skip releasing it since the rule
command owns it and it takes care of releasing it. After this update,
the set->bound field is removed.
[ 24.649883] Unable to handle kernel paging request at virtual address 0000000000040434
[ 24.657858] Mem abort info:
[ 24.660686] ESR = 0x96000004
[ 24.663769] Exception class = DABT (current EL), IL = 32 bits
[ 24.669725] SET = 0, FnV = 0
[ 24.672804] EA = 0, S1PTW = 0
[ 24.675975] Data abort info:
[ 24.678880] ISV = 0, ISS = 0x00000004
[ 24.682743] CM = 0, WnR = 0
[ 24.685723] user pgtable: 4k pages, 48-bit VAs, pgdp=0000000428952000
[ 24.692207] [0000000000040434] pgd=0000000000000000
[ 24.697119] Internal error: Oops: 96000004 [#1] SMP
[...]
[ 24.889414] Call trace:
[ 24.891870] __nf_tables_abort+0x3f0/0x7a0
[ 24.895984] nf_tables_abort+0x20/0x40
[ 24.899750] nfnetlink_rcv_batch+0x17c/0x588
[ 24.904037] nfnetlink_rcv+0x13c/0x190
[ 24.907803] netlink_unicast+0x18c/0x208
[ 24.911742] netlink_sendmsg+0x1b0/0x350
[ 24.915682] sock_sendmsg+0x4c/0x68
[ 24.919185] ___sys_sendmsg+0x288/0x2c8
[ 24.923037] __sys_sendmsg+0x7c/0xd0
[ 24.926628] __arm64_sys_sendmsg+0x2c/0x38
[ 24.930744] el0_svc_common.constprop.0+0x94/0x158
[ 24.935556] el0_svc_handler+0x34/0x90
[ 24.939322] el0_svc+0x8/0xc
[ 24.942216] Code: 37280300 f9404023 91014262 aa1703e0 (f9401863)
[ 24.948336] ---[ end trace cebbb9dcbed3b56f ]---
Fixes: f6ac85858976 ("netfilter: nf_tables: unbind set in rule from commit path")
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
sk_validate_xmit_skb() and drivers depend on the sk member of
struct sk_buff to identify segments requiring encryption.
Any operation which removes or does not preserve the original TLS
socket such as skb_orphan() or skb_clone() will cause clear text
leaks.
Make the TCP socket underlying an offloaded TLS connection
mark all skbs as decrypted, if TLS TX is in offload mode.
Then in sk_validate_xmit_skb() catch skbs which have no socket
(or a socket with no validation) and decrypted flag set.
Note that CONFIG_SOCK_VALIDATE_XMIT, CONFIG_TLS_DEVICE and
sk->sk_validate_xmit_skb are slightly interchangeable right now,
they all imply TLS offload. The new checks are guarded by
CONFIG_TLS_DEVICE because that's the option guarding the
sk_buff->decrypted member.
Second, smaller issue with orphaning is that it breaks
the guarantee that packets will be delivered to device
queues in-order. All TLS offload drivers depend on that
scheduling property. This means skb_orphan_partial()'s
trick of preserving partial socket references will cause
issues in the drivers. We need a full orphan, and as a
result netem delay/throttling will cause all TLS offload
skbs to be dropped.
Reusing the sk_buff->decrypted flag also protects from
leaking clear text when incoming, decrypted skb is redirected
(e.g. by TC).
See commit 0608c69c9a80 ("bpf: sk_msg, sock{map|hash} redirect
through ULP") for justification why the internal flag is safe.
The only location which could leak the flag in is tcp_bpf_sendmsg(),
which is taken care of by clearing the previously unused bit.
v2:
- remove superfluous decrypted mark copy (Willem);
- remove the stale doc entry (Boris);
- rely entirely on EOR marking to prevent coalescing (Boris);
- use an internal sendpages flag instead of marking the socket
(Boris).
v3 (Willem):
- reorganize the can_skb_orphan_partial() condition;
- fix the flag leak-in through tcp_bpf_sendmsg.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add get_fill_size() routine used to calculate the action size
when building a batch of events.
Fixes: ca9b0e27e ("pkt_action: add new action skbedit")
Signed-off-by: Roman Mashak <mrv@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In error case, all entries should be freed from the sched list
before deleting it. For simplicity use rcu way.
Fixes: 5a781ccbd19e46 ("tc: Add support for configuring the taprio scheduler")
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Before commit d4289fcc9b16 ("net: IP6 defrag: use rbtrees for IPv6
defrag"), a netperf UDP_STREAM test[0] using big IPv6 datagrams (thus
generating many fragments) and running over an IPsec tunnel, reported
more than 6Gbps throughput. After that patch, the same test gets only
9Mbps when receiving on a be2net nic (driver can make a big difference
here, for example, ixgbe doesn't seem to be affected).
By reusing the IPv4 defragmentation code, IPv6 lost fragment coalescing
(IPv4 fragment coalescing was dropped by commit 14fe22e33462 ("Revert
"ipv4: use skb coalescing in defragmentation"")).
Without fragment coalescing, be2net runs out of Rx ring entries and
starts to drop frames (ethtool reports rx_drops_no_frags errors). Since
the netperf traffic is only composed of UDP fragments, any lost packet
prevents reassembly of the full datagram. Therefore, fragments which
have no possibility to ever get reassembled pile up in the reassembly
queue, until the memory accounting exeeds the threshold. At that point
no fragment is accepted anymore, which effectively discards all
netperf traffic.
When reassembly timeout expires, some stale fragments are removed from
the reassembly queue, so a few packets can be received, reassembled
and delivered to the netperf receiver. But the nic still drops frames
and soon the reassembly queue gets filled again with stale fragments.
These long time frames where no datagram can be received explain why
the performance drop is so significant.
Re-introducing fragment coalescing is enough to get the initial
performances again (6.6Gbps with be2net): driver doesn't drop frames
anymore (no more rx_drops_no_frags errors) and the reassembly engine
works at full speed.
This patch is quite conservative and only coalesces skbs for local
IPv4 and IPv6 delivery (in order to avoid changing skb geometry when
forwarding). Coalescing could be extended in the future if need be, as
more scenarios would probably benefit from it.
[0]: Test configuration
Sender:
ip xfrm policy flush
ip xfrm state flush
ip xfrm state add src fc00:1::1 dst fc00:2::1 proto esp spi 0x1000 aead 'rfc4106(gcm(aes))' 0x0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b 96 mode transport sel src fc00:1::1 dst fc00:2::1
ip xfrm policy add src fc00:1::1 dst fc00:2::1 dir in tmpl src fc00:1::1 dst fc00:2::1 proto esp mode transport action allow
ip xfrm state add src fc00:2::1 dst fc00:1::1 proto esp spi 0x1001 aead 'rfc4106(gcm(aes))' 0x0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b 96 mode transport sel src fc00:2::1 dst fc00:1::1
ip xfrm policy add src fc00:2::1 dst fc00:1::1 dir out tmpl src fc00:2::1 dst fc00:1::1 proto esp mode transport action allow
netserver -D -L fc00:2::1
Receiver:
ip xfrm policy flush
ip xfrm state flush
ip xfrm state add src fc00:2::1 dst fc00:1::1 proto esp spi 0x1001 aead 'rfc4106(gcm(aes))' 0x0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b 96 mode transport sel src fc00:2::1 dst fc00:1::1
ip xfrm policy add src fc00:2::1 dst fc00:1::1 dir in tmpl src fc00:2::1 dst fc00:1::1 proto esp mode transport action allow
ip xfrm state add src fc00:1::1 dst fc00:2::1 proto esp spi 0x1000 aead 'rfc4106(gcm(aes))' 0x0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b 96 mode transport sel src fc00:1::1 dst fc00:2::1
ip xfrm policy add src fc00:1::1 dst fc00:2::1 dir out tmpl src fc00:1::1 dst fc00:2::1 proto esp mode transport action allow
netperf -H fc00:2::1 -f k -P 0 -L fc00:1::1 -l 60 -t UDP_STREAM -I 99,5 -i 5,5 -T5,5 -6
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Simon Wunderlich says:
====================
Here are some batman-adv bugfixes:
- Fix netlink dumping of all mcast_flags buckets, by Sven Eckelmann
- Fix deletion of RTR(4|6) mcast list entries, by Sven Eckelmann
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When RX timestamping is enabled and two link-local (non-meta) frames are
received in a row, this constitutes an error.
The tagger is always caching the last link-local frame, in an attempt to
merge it with the meta follow-up frame when that arrives. To recover
from the above error condition, the initial cached link-local frame is
dropped and the second frame in a row is cached (in expectance of the
second meta frame).
However, when dropping the initial link-local frame, its backing memory
was being leaked.
Fixes: f3097be21bf1 ("net: dsa: sja1105: Add a state machine for RX timestamping")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After a meta frame is received, it is associated with the cached
sp->data->stampable_skb from the DSA tagger private structure.
Cached means its refcount is incremented with skb_get() in order for
dsa_switch_rcv() to not free it when the tagger .rcv returns NULL.
The mistake is that skb_unref() is not the correct function to use. It
will correctly decrement the refcount (which will go back to zero) but
the skb memory will not be freed. That is the job of kfree_skb(), which
also calls skb_unref().
But it turns out that freeing the cached stampable_skb is in fact not
necessary. It is still a perfectly valid skb, and now it is even
annotated with the partial RX timestamp. So remove the skb_copy()
altogether and simply pass the stampable_skb with a refcount of 1
(incremented by us, decremented by dsa_switch_rcv) up the stack.
Fixes: f3097be21bf1 ("net: dsa: sja1105: Add a state machine for RX timestamping")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add get_fill_size() routine used to calculate the action size
when building a batch of events.
Fixes: c7e2b9689 ("sched: introduce vlan action")
Signed-off-by: Roman Mashak <mrv@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Most of the bridge device's vlan init bugs come from the fact that its
default pvid is created at the wrong time, way too early in ndo_init()
before the device is even assigned an ifindex. It introduces a bug when the
bridge's dev_addr is added as fdb during the initial default pvid creation
the notification has ifindex/NDA_MASTER both equal to 0 (see example below)
which really makes no sense for user-space[0] and is wrong.
Usually user-space software would ignore such entries, but they are
actually valid and will eventually have all necessary attributes.
It makes much more sense to send a notification *after* the device has
registered and has a proper ifindex allocated rather than before when
there's a chance that the registration might still fail or to receive
it with ifindex/NDA_MASTER == 0. Note that we can remove the fdb flush
from br_vlan_flush() since that case can no longer happen. At
NETDEV_REGISTER br->default_pvid is always == 1 as it's initialized by
br_vlan_init() before that and at NETDEV_UNREGISTER it can be anything
depending why it was called (if called due to NETDEV_REGISTER error
it'll still be == 1, otherwise it could be any value changed during the
device life time).
For the demonstration below a small change to iproute2 for printing all fdb
notifications is added, because it contained a workaround not to show
entries with ifindex == 0.
Command executed while monitoring: $ ip l add br0 type bridge
Before (both ifindex and master == 0):
$ bridge monitor fdb
36:7e:8a:b3:56:ba dev * vlan 1 master * permanent
After (proper br0 ifindex):
$ bridge monitor fdb
e6:2a:ae:7a:b7:48 dev br0 vlan 1 master br0 permanent
v4: move only the default pvid init/deinit to NETDEV_REGISTER/UNREGISTER
v3: send the correct v2 patch with all changes (stub should return 0)
v2: on error in br_vlan_init set br->vlgrp to NULL and return 0 in
the br_vlan_bridge_event stub when bridge vlans are disabled
[0] https://bugzilla.kernel.org/show_bug.cgi?id=204389
Reported-by: michael-dev <michael-dev@fami-braun.de>
Fixes: 5be5a2df40f0 ("bridge: Add filtering support for default_pvid")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
FASTOPEN is not possible with SMC. sendmsg() with msg_flag MSG_FASTOPEN
triggers a fallback to TCP if the socket is in state SMC_INIT.
But if a nonblocking connect is already started, fallback to TCP
is no longer possible, even though the socket may still be in state
SMC_INIT.
And if a nonblocking connect is already started, a listen() call
does not make sense.
Reported-by: syzbot+bd8cc73d665590a1fcad@syzkaller.appspotmail.com
Fixes: 50717a37db032 ("net/smc: nonblocking connect rework")
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The setsockopts options TCP_NODELAY and TCP_CORK may schedule the
tx worker. Make sure the socket is not yet moved into SMC_CLOSED
state (for instance by a shutdown SHUT_RDWR call).
Reported-by: syzbot+92209502e7aab127c75f@syzkaller.appspotmail.com
Reported-by: syzbot+b972214bb803a343f4fe@syzkaller.appspotmail.com
Fixes: 01d2f7e2cdd31 ("net/smc: sockopts TCP_NODELAY and TCP_CORK")
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The nexthop path in rt6_update_exception_stamp_rt needs to call
rcu_read_unlock if it fails to find a fib6_nh match rather than
just returning.
Fixes: e659ba31d806 ("ipv6: Handle all fib6_nh in a nexthop in exception handling")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Looks like we were slightly overzealous with the shutdown()
cleanup. Even though the sock->sk_state can reach CLOSED again,
socket->state will not got back to SS_UNCONNECTED once
connections is ESTABLISHED. Meaning we will see EISCONN if
we try to reconnect, and EINVAL if we try to listen.
Only listen sockets can be shutdown() and reused, but since
ESTABLISHED sockets can never be re-connected() or used for
listen() we don't need to try to clean up the ULP state early.
Fixes: 32857cf57f92 ("net/tls: fix transition through disconnect with close")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When generic-XDP was moved to a later processing step by commit
458bf2f224f0 ("net: core: support XDP generic on stacked devices.")
a regression was introduced when using bpf_xdp_adjust_head.
The issue is that after this commit the skb->network_header is now
changed prior to calling generic XDP and not after. Thus, if the header
is changed by XDP (via bpf_xdp_adjust_head), then skb->network_header
also need to be updated again. Fix by calling skb_reset_network_header().
Fixes: 458bf2f224f0 ("net: core: support XDP generic on stacked devices.")
Reported-by: Brandon Cazander <brandon.cazander@multapplied.net>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently init call of all actions (except ipt) init their 'parm'
structure as a direct pointer to nla data in skb. This leads to race
condition when some of the filter actions were initialized successfully
(and were assigned with idr action index that was written directly
into nla data), but then were deleted and retried (due to following
action module missing or classifier-initiated retry), in which case
action init code tries to insert action to idr with index that was
assigned on previous iteration. During retry the index can be reused
by another action that was inserted concurrently, which causes
unintended action sharing between filters.
To fix described race condition, save action idr index to temporary
stack-allocated variable instead on nla data.
Fixes: 0190c1d452a9 ("net: sched: atomically check-allocate action")
Signed-off-by: Dmytro Linkin <dmitrolin@mellanox.com>
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This makes the previously added 'encap test' pass.
Because its possible that the xfrm dst entry becomes stale while such
a flow is offloaded, we need to call dst_check() -- the notifier that
handles this for non-tunneled traffic isn't sufficient, because SA or
or policies might have changed.
If dst becomes stale the flow offload entry will be tagged for teardown
and packets will be passed to 'classic' forwarding path.
Removing the entry right away is problematic, as this would
introduce a race condition with the gc worker.
In case flow is long-lived, it could eventually be offloaded again
once the gc worker removes the entry from the flow table.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
There is a race condition for an established connection that is being closed
by the guest: the refcnt is 4 at the end of hvs_release() (Note: here the
'remove_sock' is false):
1 for the initial value;
1 for the sk being in the bound list;
1 for the sk being in the connected list;
1 for the delayed close_work.
After hvs_release() finishes, __vsock_release() -> sock_put(sk) *may*
decrease the refcnt to 3.
Concurrently, hvs_close_connection() runs in another thread:
calls vsock_remove_sock() to decrease the refcnt by 2;
call sock_put() to decrease the refcnt to 0, and free the sk;
next, the "release_sock(sk)" may hang due to use-after-free.
In the above, after hvs_release() finishes, if hvs_close_connection() runs
faster than "__vsock_release() -> sock_put(sk)", then there is not any issue,
because at the beginning of hvs_close_connection(), the refcnt is still 4.
The issue can be resolved if an extra reference is taken when the
connection is established.
Fixes: a9eeb998c28d ("hv_sock: Add support for delayed close")
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Reviewed-by: Sunil Muthuswamy <sunilmut@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 2753ca5d9009 ("tipc: fix uninit-value in tipc_nl_compat_doit")
broke older tipc tools that use compat interface (e.g. tipc-config from
tipcutils package):
% tipc-config -p
operation not supported
The commit started to reject TIPC netlink compat messages that do not
have attributes. It is too restrictive because some of such messages are
valid (they don't need any arguments):
% grep 'tx none' include/uapi/linux/tipc_config.h
#define TIPC_CMD_NOOP 0x0000 /* tx none, rx none */
#define TIPC_CMD_GET_MEDIA_NAMES 0x0002 /* tx none, rx media_name(s) */
#define TIPC_CMD_GET_BEARER_NAMES 0x0003 /* tx none, rx bearer_name(s) */
#define TIPC_CMD_SHOW_PORTS 0x0006 /* tx none, rx ultra_string */
#define TIPC_CMD_GET_REMOTE_MNG 0x4003 /* tx none, rx unsigned */
#define TIPC_CMD_GET_MAX_PORTS 0x4004 /* tx none, rx unsigned */
#define TIPC_CMD_GET_NETID 0x400B /* tx none, rx unsigned */
#define TIPC_CMD_NOT_NET_ADMIN 0xC001 /* tx none, rx none */
This patch relaxes the original fix and rejects messages without
arguments only if such arguments are expected by a command (reg_type is
non zero).
Fixes: 2753ca5d9009 ("tipc: fix uninit-value in tipc_nl_compat_doit")
Cc: stable@vger.kernel.org
Signed-off-by: Taras Kondratiuk <takondra@cisco.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When permanent entries were introduced by the commit below, they were
exempt from timing out and thus igmp leave wouldn't affect them unless
fast leave was enabled on the port which was added before permanent
entries existed. It shouldn't matter if fast leave is enabled or not
if the user added a permanent entry it shouldn't be deleted on igmp
leave.
Before:
$ echo 1 > /sys/class/net/eth4/brport/multicast_fast_leave
$ bridge mdb add dev br0 port eth4 grp 229.1.1.1 permanent
$ bridge mdb show
dev br0 port eth4 grp 229.1.1.1 permanent
< join and leave 229.1.1.1 on eth4 >
$ bridge mdb show
$
After:
$ echo 1 > /sys/class/net/eth4/brport/multicast_fast_leave
$ bridge mdb add dev br0 port eth4 grp 229.1.1.1 permanent
$ bridge mdb show
dev br0 port eth4 grp 229.1.1.1 permanent
< join and leave 229.1.1.1 on eth4 >
$ bridge mdb show
dev br0 port eth4 grp 229.1.1.1 permanent
Fixes: ccb1c31a7a87 ("bridge: add flags to distinguish permanent mdb entires")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Just a few fixes:
* revert NETIF_F_LLTX usage as it caused problems
* avoid warning on WMM parameters from AP that are too short
* fix possible null-ptr dereference in hwsim
* fix interface combinations with 4-addr and crypto control
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pablo Neira Ayuso says:
====================
netfilter fixes for net
The following patchset contains Netfilter fixes for your net tree:
1) memleak in ebtables from the error path for the 32/64 compat layer,
from Florian Westphal.
2) Fix inverted meta ifname/ifidx matching when no interface is set
on either from the input/output path, from Phil Sutter.
3) Remove goto label in nft_meta_bridge, also from Phil.
4) Missing include guard in xt_connlabel, from Masahiro Yamada.
5) Two patch to fix ipset destination MAC matching coming from
Stephano Brivio, via Jozsef Kadlecsik.
6) Fix set rename and listing concurrency problem, from Shijie Luo.
Patch also coming via Jozsef Kadlecsik.
7) ebtables 32/64 compat missing base chain policy in rule count,
from Florian Westphal.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Support for handling the PPPOEIOCSFWD ioctl in compat mode was added in
linux-2.5.69 along with hundreds of other commands, but was always broken
sincen only the structure is compatible, but the command number is not,
due to the size being sizeof(size_t), or at first sizeof(sizeof((struct
sockaddr_pppox)), which is different on 64-bit architectures.
Guillaume Nault adds:
And the implementation was broken until 2016 (see 29e73269aa4d ("pppoe:
fix reference counting in PPPoE proxy")), and nobody ever noticed. I
should probably have removed this ioctl entirely instead of fixing it.
Clearly, it has never been used.
Fix it by adding a compat_ioctl handler for all pppoe variants that
translates the command number and then calls the regular ioctl function.
All other ioctl commands handled by pppoe are compatible between 32-bit
and 64-bit, and require compat_ptr() conversion.
This should apply to all stable kernels.
Acked-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Our test suite somtimes provokes the following crash:
Description of problem:
[ 1092.597234] BUG: unable to handle kernel NULL pointer dereference at 00000000000000e8
[ 1092.605072] PGD 0 P4D 0
[ 1092.607620] Oops: 0000 [#1] SMP PTI
[ 1092.611118] CPU: 37 PID: 0 Comm: swapper/37 Kdump: loaded Not tainted 4.18.0-122.el8.x86_64 #1
[ 1092.619724] Hardware name: Dell Inc. PowerEdge R740/08D89F, BIOS 1.3.7 02/08/2018
[ 1092.627215] RIP: 0010:tipc_mcast_filter_msg+0x93/0x2d0 [tipc]
[ 1092.632955] Code: 0f 84 aa 01 00 00 89 cf 4d 01 ca 4c 8b 26 c1 ef 19 83 e7 0f 83 ff 0c 4d 0f 45 d1 41 8b 6a 10 0f cd 4c 39 e6 0f 84 81 01 00 00 <4d> 8b 9c 24 e8 00 00 00 45 8b 13 41 0f ca 44 89 d7 c1 ef 13 83 e7
[ 1092.651703] RSP: 0018:ffff929e5fa83a18 EFLAGS: 00010282
[ 1092.656927] RAX: ffff929e3fb38100 RBX: 00000000069f29ee RCX: 00000000416c0045
[ 1092.664058] RDX: ffff929e5fa83a88 RSI: ffff929e31a28420 RDI: 0000000000000000
[ 1092.671209] RBP: 0000000029b11821 R08: 0000000000000000 R09: ffff929e39b4407a
[ 1092.678343] R10: ffff929e39b4407a R11: 0000000000000007 R12: 0000000000000000
[ 1092.685475] R13: 0000000000000001 R14: ffff929e3fb38100 R15: ffff929e39b4407a
[ 1092.692614] FS: 0000000000000000(0000) GS:ffff929e5fa80000(0000) knlGS:0000000000000000
[ 1092.700702] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 1092.706447] CR2: 00000000000000e8 CR3: 000000031300a004 CR4: 00000000007606e0
[ 1092.713579] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 1092.720712] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 1092.727843] PKRU: 55555554
[ 1092.730556] Call Trace:
[ 1092.733010] <IRQ>
[ 1092.735034] tipc_sk_filter_rcv+0x7ca/0xb80 [tipc]
[ 1092.739828] ? __kmalloc_node_track_caller+0x1cb/0x290
[ 1092.744974] ? dev_hard_start_xmit+0xa5/0x210
[ 1092.749332] tipc_sk_rcv+0x389/0x640 [tipc]
[ 1092.753519] tipc_sk_mcast_rcv+0x23c/0x3a0 [tipc]
[ 1092.758224] tipc_rcv+0x57a/0xf20 [tipc]
[ 1092.762154] ? ktime_get_real_ts64+0x40/0xe0
[ 1092.766432] ? tpacket_rcv+0x50/0x9f0
[ 1092.770098] tipc_l2_rcv_msg+0x4a/0x70 [tipc]
[ 1092.774452] __netif_receive_skb_core+0xb62/0xbd0
[ 1092.779164] ? enqueue_entity+0xf6/0x630
[ 1092.783084] ? kmem_cache_alloc+0x158/0x1c0
[ 1092.787272] ? __build_skb+0x25/0xd0
[ 1092.790849] netif_receive_skb_internal+0x42/0xf0
[ 1092.795557] napi_gro_receive+0xba/0xe0
[ 1092.799417] mlx5e_handle_rx_cqe+0x83/0xd0 [mlx5_core]
[ 1092.804564] mlx5e_poll_rx_cq+0xd5/0x920 [mlx5_core]
[ 1092.809536] mlx5e_napi_poll+0xb2/0xce0 [mlx5_core]
[ 1092.814415] ? __wake_up_common_lock+0x89/0xc0
[ 1092.818861] net_rx_action+0x149/0x3b0
[ 1092.822616] __do_softirq+0xe3/0x30a
[ 1092.826193] irq_exit+0x100/0x110
[ 1092.829512] do_IRQ+0x85/0xd0
[ 1092.832483] common_interrupt+0xf/0xf
[ 1092.836147] </IRQ>
[ 1092.838255] RIP: 0010:cpuidle_enter_state+0xb7/0x2a0
[ 1092.843221] Code: e8 3e 79 a5 ff 80 7c 24 03 00 74 17 9c 58 0f 1f 44 00 00 f6 c4 02 0f 85 d7 01 00 00 31 ff e8 a0 6b ab ff fb 66 0f 1f 44 00 00 <48> b8 ff ff ff ff f3 01 00 00 4c 29 f3 ba ff ff ff 7f 48 39 c3 7f
[ 1092.861967] RSP: 0018:ffffaa5ec6533e98 EFLAGS: 00000246 ORIG_RAX: ffffffffffffffdd
[ 1092.869530] RAX: ffff929e5faa3100 RBX: 000000fe63dd2092 RCX: 000000000000001f
[ 1092.876665] RDX: 000000fe63dd2092 RSI: 000000003a518aaa RDI: 0000000000000000
[ 1092.883795] RBP: 0000000000000003 R08: 0000000000000004 R09: 0000000000022940
[ 1092.890929] R10: 0000040cb0666b56 R11: ffff929e5faa20a8 R12: ffff929e5faade78
[ 1092.898060] R13: ffffffffb59258f8 R14: 000000fe60f3228d R15: 0000000000000000
[ 1092.905196] ? cpuidle_enter_state+0x92/0x2a0
[ 1092.909555] do_idle+0x236/0x280
[ 1092.912785] cpu_startup_entry+0x6f/0x80
[ 1092.916715] start_secondary+0x1a7/0x200
[ 1092.920642] secondary_startup_64+0xb7/0xc0
[...]
The reason is that the skb list tipc_socket::mc_method.deferredq only
is initialized for connectionless sockets, while nothing stops arriving
multicast messages from being filtered by connection oriented sockets,
with subsequent access to the said list.
We fix this by initializing the list unconditionally at socket creation.
This eliminates the crash, while the message still is dropped further
down in tipc_sk_filter_rcv() as it should be.
Reported-by: Li Shuang <shuali@redhat.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
