summaryrefslogtreecommitdiff
path: root/net
AgeCommit message (Collapse)Author
2018-09-24ip_tunnel: be careful when accessing the inner headerPaolo Abeni
Cong noted that we need the same checks introduced by commit 76c0ddd8c3a6 ("ip6_tunnel: be careful when accessing the inner header") even for ipv4 tunnels. Fixes: c54419321455 ("GRE: Refactor GRE tunneling code.") Suggested-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-24mpls: allow routes on ip6gre devicesSaif Hasan
Summary: This appears to be necessary and sufficient change to enable `MPLS` on `ip6gre` tunnels (RFC4023). This diff allows IP6GRE devices to be recognized by MPLS kernel module and hence user can configure interface to accept packets with mpls headers as well setup mpls routes on them. Test Plan: Test plan consists of multiple containers connected via GRE-V6 tunnel. Then carrying out testing steps as below. - Carry out necessary sysctl settings on all containers ``` sysctl -w net.mpls.platform_labels=65536 sysctl -w net.mpls.ip_ttl_propagate=1 sysctl -w net.mpls.conf.lo.input=1 ``` - Establish IP6GRE tunnels ``` ip -6 tunnel add name if_1_2_1 mode ip6gre \ local 2401:db00:21:6048:feed:0::1 \ remote 2401:db00:21:6048:feed:0::2 key 1 ip link set dev if_1_2_1 up sysctl -w net.mpls.conf.if_1_2_1.input=1 ip -4 addr add 169.254.0.2/31 dev if_1_2_1 scope link ip -6 tunnel add name if_1_3_1 mode ip6gre \ local 2401:db00:21:6048:feed:0::1 \ remote 2401:db00:21:6048:feed:0::3 key 1 ip link set dev if_1_3_1 up sysctl -w net.mpls.conf.if_1_3_1.input=1 ip -4 addr add 169.254.0.4/31 dev if_1_3_1 scope link ``` - Install MPLS encap rules on node-1 towards node-2 ``` ip route add 192.168.0.11/32 nexthop encap mpls 32/64 \ via inet 169.254.0.3 dev if_1_2_1 ``` - Install MPLS forwarding rules on node-2 and node-3 ``` // node2 ip -f mpls route add 32 via inet 169.254.0.7 dev if_2_4_1 // node3 ip -f mpls route add 64 via inet 169.254.0.12 dev if_4_3_1 ``` - Ping 192.168.0.11 (node4) from 192.168.0.1 (node1) (where routing towards 192.168.0.1 is via IP route directly towards node1 from node4) ``` ping 192.168.0.11 ``` - tcpdump on interface to capture ping packets wrapped within MPLS header which inturn wrapped within IP6GRE header ``` 16:43:41.121073 IP6 2401:db00:21:6048:feed::1 > 2401:db00:21:6048:feed::2: DSTOPT GREv0, key=0x1, length 100: MPLS (label 32, exp 0, ttl 255) (label 64, exp 0, [S], ttl 255) IP 192.168.0.1 > 192.168.0.11: ICMP echo request, id 1208, seq 45, length 64 0x0000: 6000 2cdb 006c 3c3f 2401 db00 0021 6048 `.,..l<?$....!`H 0x0010: feed 0000 0000 0001 2401 db00 0021 6048 ........$....!`H 0x0020: feed 0000 0000 0002 2f00 0401 0401 0100 ......../....... 0x0030: 2000 8847 0000 0001 0002 00ff 0004 01ff ...G............ 0x0040: 4500 0054 3280 4000 ff01 c7cb c0a8 0001 E..T2.@......... 0x0050: c0a8 000b 0800 a8d7 04b8 002d 2d3c a05b ...........--<.[ 0x0060: 0000 0000 bcd8 0100 0000 0000 1011 1213 ................ 0x0070: 1415 1617 1819 1a1b 1c1d 1e1f 2021 2223 .............!"# 0x0080: 2425 2627 2829 2a2b 2c2d 2e2f 3031 3233 $%&'()*+,-./0123 0x0090: 3435 3637 4567 ``` Signed-off-by: Saif Hasan <has@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-23netpoll: make ndo_poll_controller() optionalEric Dumazet
As diagnosed by Song Liu, ndo_poll_controller() can be very dangerous on loaded hosts, since the cpu calling ndo_poll_controller() might steal all NAPI contexts (for all RX/TX queues of the NIC). This capture can last for unlimited amount of time, since one cpu is generally not able to drain all the queues under load. It seems that all networking drivers that do use NAPI for their TX completions, should not provide a ndo_poll_controller(). NAPI drivers have netpoll support already handled in core networking stack, since netpoll_poll_dev() uses poll_napi(dev) to iterate through registered NAPI contexts for a device. This patch allows netpoll_poll_dev() to process NAPI contexts even for drivers not providing ndo_poll_controller(), allowing for following patches in NAPI drivers. Also we export netpoll_poll_dev() so that it can be called by bonding/team drivers in following patches. Reported-by: Song Liu <songliubraving@fb.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Tested-by: Song Liu <songliubraving@fb.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-23rds: Fix build regression.David S. Miller
Use DECLARE_* not DEFINE_* Fixes: 8360ed6745df ("RDS: IB: Use DEFINE_PER_CPU_SHARED_ALIGNED for rds_ib_stats") Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-22net-ethtool: ETHTOOL_GUFO did not and should not require CAP_NET_ADMINMaciej Żenczykowski
So it should not fail with EPERM even though it is no longer implemented... This is a fix for: (userns)$ egrep ^Cap /proc/self/status CapInh: 0000003fffffffff CapPrm: 0000003fffffffff CapEff: 0000003fffffffff CapBnd: 0000003fffffffff CapAmb: 0000003fffffffff (userns)$ tcpdump -i usb_rndis0 tcpdump: WARNING: usb_rndis0: SIOCETHTOOL(ETHTOOL_GUFO) ioctl failed: Operation not permitted Warning: Kernel filter failed: Bad file descriptor tcpdump: can't remove kernel filter: Bad file descriptor With this change it returns EOPNOTSUPP instead of EPERM. See also https://github.com/the-tcpdump-group/libpcap/issues/689 Fixes: 08a00fea6de2 "net: Remove references to NETIF_F_UFO from ethtool." Cc: David S. Miller <davem@davemloft.net> Signed-off-by: Maciej Żenczykowski <maze@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-21RDS: IB: Use DEFINE_PER_CPU_SHARED_ALIGNED for rds_ib_statsNathan Chancellor
Clang warns when two declarations' section attributes don't match. net/rds/ib_stats.c:40:1: warning: section does not match previous declaration [-Wsection] DEFINE_PER_CPU_SHARED_ALIGNED(struct rds_ib_statistics, rds_ib_stats); ^ ./include/linux/percpu-defs.h:142:2: note: expanded from macro 'DEFINE_PER_CPU_SHARED_ALIGNED' DEFINE_PER_CPU_SECTION(type, name, PER_CPU_SHARED_ALIGNED_SECTION) \ ^ ./include/linux/percpu-defs.h:93:9: note: expanded from macro 'DEFINE_PER_CPU_SECTION' extern __PCPU_ATTRS(sec) __typeof__(type) name; \ ^ ./include/linux/percpu-defs.h:49:26: note: expanded from macro '__PCPU_ATTRS' __percpu __attribute__((section(PER_CPU_BASE_SECTION sec))) \ ^ net/rds/ib.h:446:1: note: previous attribute is here DECLARE_PER_CPU(struct rds_ib_statistics, rds_ib_stats); ^ ./include/linux/percpu-defs.h:111:2: note: expanded from macro 'DECLARE_PER_CPU' DECLARE_PER_CPU_SECTION(type, name, "") ^ ./include/linux/percpu-defs.h:87:9: note: expanded from macro 'DECLARE_PER_CPU_SECTION' extern __PCPU_ATTRS(sec) __typeof__(type) name ^ ./include/linux/percpu-defs.h:49:26: note: expanded from macro '__PCPU_ATTRS' __percpu __attribute__((section(PER_CPU_BASE_SECTION sec))) \ ^ 1 warning generated. The initial definition was added in commit ec16227e1414 ("RDS/IB: Infiniband transport") and the cache aligned definition was added in commit e6babe4cc4ce ("RDS/IB: Stats and sysctls") right after. The definition probably should have been updated in net/rds/ib.h, which is what this patch does. Link: https://github.com/ClangBuiltLinux/linux/issues/114 Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-21devlink: double free in devlink_resource_fill()Dan Carpenter
Smatch reports that devlink_dpipe_send_and_alloc_skb() frees the skb on error so this is a double free. We fixed a bunch of these bugs in commit 7fe4d6dcbcb4 ("devlink: Remove redundant free on error path") but we accidentally overlooked this one. Fixes: d9f9b9a4d05f ("devlink: Add support for resource abstraction") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-21net/ipv6: Display all addresses in output of /proc/net/if_inet6Jeff Barnhill
The backend handling for /proc/net/if_inet6 in addrconf.c doesn't properly handle starting/stopping the iteration. The problem is that at some point during the iteration, an overflow is detected and the process is subsequently stopped. The item being shown via seq_printf() when the overflow occurs is not actually shown, though. When start() is subsequently called to resume iterating, it returns the next item, and thus the item that was being processed when the overflow occurred never gets printed. Alter the meaning of the private data member "offset". Currently, when it is not 0 (which only happens at the very beginning), "offset" represents the next hlist item to be printed. After this change, "offset" always represents the current item. This is also consistent with the private data member "bucket", which represents the current bucket, and also the use of "pos" as defined in seq_file.txt: The pos passed to start() will always be either zero, or the most recent pos used in the previous session. Signed-off-by: Jeff Barnhill <0xeffeff@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-21netlabel: check for IPV4MASK in addrinfo_getSean Tranchetti
netlbl_unlabel_addrinfo_get() assumes that if it finds the NLBL_UNLABEL_A_IPV4ADDR attribute, it must also have the NLBL_UNLABEL_A_IPV4MASK attribute as well. However, this is not necessarily the case as the current checks in netlbl_unlabel_staticadd() and friends are not sufficent to enforce this. If passed a netlink message with NLBL_UNLABEL_A_IPV4ADDR, NLBL_UNLABEL_A_IPV6ADDR, and NLBL_UNLABEL_A_IPV6MASK attributes, these functions will all call netlbl_unlabel_addrinfo_get() which will then attempt dereference NULL when fetching the non-existent NLBL_UNLABEL_A_IPV4MASK attribute: Unable to handle kernel NULL pointer dereference at virtual address 0 Process unlab (pid: 31762, stack limit = 0xffffff80502d8000) Call trace: netlbl_unlabel_addrinfo_get+0x44/0xd8 netlbl_unlabel_staticremovedef+0x98/0xe0 genl_rcv_msg+0x354/0x388 netlink_rcv_skb+0xac/0x118 genl_rcv+0x34/0x48 netlink_unicast+0x158/0x1f0 netlink_sendmsg+0x32c/0x338 sock_sendmsg+0x44/0x60 ___sys_sendmsg+0x1d0/0x2a8 __sys_sendmsg+0x64/0xb4 SyS_sendmsg+0x34/0x4c el0_svc_naked+0x34/0x38 Code: 51001149 7100113f 540000a0 f9401508 (79400108) ---[ end trace f6438a488e737143 ]--- Kernel panic - not syncing: Fatal exception Signed-off-by: Sean Tranchetti <stranche@codeaurora.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-20sctp: update dst pmtu with the correct daddrXin Long
When processing pmtu update from an icmp packet, it calls .update_pmtu with sk instead of skb in sctp_transport_update_pmtu. However for sctp, the daddr in the transport might be different from inet_sock->inet_daddr or sk->sk_v6_daddr, which is used to update or create the route cache. The incorrect daddr will cause a different route cache created for the path. So before calling .update_pmtu, inet_sock->inet_daddr/sk->sk_v6_daddr should be updated with the daddr in the transport, and update it back after it's done. The issue has existed since route exceptions introduction. Fixes: 4895c771c7f0 ("ipv4: Add FIB nexthop exceptions.") Reported-by: ian.periam@dialogic.com Signed-off-by: Xin Long <lucien.xin@gmail.com> Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-20smc: generic netlink family should be __ro_after_initJohannes Berg
The generic netlink family is only initialized during module init, so it should be __ro_after_init like all other generic netlink families. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-19ip6_tunnel: be careful when accessing the inner headerPaolo Abeni
the ip6 tunnel xmit ndo assumes that the processed skb always contains an ip[v6] header, but syzbot has found a way to send frames that fall short of this assumption, leading to the following splat: BUG: KMSAN: uninit-value in ip6ip6_tnl_xmit net/ipv6/ip6_tunnel.c:1307 [inline] BUG: KMSAN: uninit-value in ip6_tnl_start_xmit+0x7d2/0x1ef0 net/ipv6/ip6_tunnel.c:1390 CPU: 0 PID: 4504 Comm: syz-executor558 Not tainted 4.16.0+ #87 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011 Call Trace: __dump_stack lib/dump_stack.c:17 [inline] dump_stack+0x185/0x1d0 lib/dump_stack.c:53 kmsan_report+0x142/0x240 mm/kmsan/kmsan.c:1067 __msan_warning_32+0x6c/0xb0 mm/kmsan/kmsan_instr.c:683 ip6ip6_tnl_xmit net/ipv6/ip6_tunnel.c:1307 [inline] ip6_tnl_start_xmit+0x7d2/0x1ef0 net/ipv6/ip6_tunnel.c:1390 __netdev_start_xmit include/linux/netdevice.h:4066 [inline] netdev_start_xmit include/linux/netdevice.h:4075 [inline] xmit_one net/core/dev.c:3026 [inline] dev_hard_start_xmit+0x5f1/0xc70 net/core/dev.c:3042 __dev_queue_xmit+0x27ee/0x3520 net/core/dev.c:3557 dev_queue_xmit+0x4b/0x60 net/core/dev.c:3590 packet_snd net/packet/af_packet.c:2944 [inline] packet_sendmsg+0x7c70/0x8a30 net/packet/af_packet.c:2969 sock_sendmsg_nosec net/socket.c:630 [inline] sock_sendmsg net/socket.c:640 [inline] ___sys_sendmsg+0xec0/0x1310 net/socket.c:2046 __sys_sendmmsg+0x42d/0x800 net/socket.c:2136 SYSC_sendmmsg+0xc4/0x110 net/socket.c:2167 SyS_sendmmsg+0x63/0x90 net/socket.c:2162 do_syscall_64+0x309/0x430 arch/x86/entry/common.c:287 entry_SYSCALL_64_after_hwframe+0x3d/0xa2 RIP: 0033:0x441819 RSP: 002b:00007ffe58ee8268 EFLAGS: 00000213 ORIG_RAX: 0000000000000133 RAX: ffffffffffffffda RBX: 0000000000000003 RCX: 0000000000441819 RDX: 0000000000000002 RSI: 0000000020000100 RDI: 0000000000000003 RBP: 00000000006cd018 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000213 R12: 0000000000402510 R13: 00000000004025a0 R14: 0000000000000000 R15: 0000000000000000 Uninit was created at: kmsan_save_stack_with_flags mm/kmsan/kmsan.c:278 [inline] kmsan_internal_poison_shadow+0xb8/0x1b0 mm/kmsan/kmsan.c:188 kmsan_kmalloc+0x94/0x100 mm/kmsan/kmsan.c:314 kmsan_slab_alloc+0x11/0x20 mm/kmsan/kmsan.c:321 slab_post_alloc_hook mm/slab.h:445 [inline] slab_alloc_node mm/slub.c:2737 [inline] __kmalloc_node_track_caller+0xaed/0x11c0 mm/slub.c:4369 __kmalloc_reserve net/core/skbuff.c:138 [inline] __alloc_skb+0x2cf/0x9f0 net/core/skbuff.c:206 alloc_skb include/linux/skbuff.h:984 [inline] alloc_skb_with_frags+0x1d4/0xb20 net/core/skbuff.c:5234 sock_alloc_send_pskb+0xb56/0x1190 net/core/sock.c:2085 packet_alloc_skb net/packet/af_packet.c:2803 [inline] packet_snd net/packet/af_packet.c:2894 [inline] packet_sendmsg+0x6454/0x8a30 net/packet/af_packet.c:2969 sock_sendmsg_nosec net/socket.c:630 [inline] sock_sendmsg net/socket.c:640 [inline] ___sys_sendmsg+0xec0/0x1310 net/socket.c:2046 __sys_sendmmsg+0x42d/0x800 net/socket.c:2136 SYSC_sendmmsg+0xc4/0x110 net/socket.c:2167 SyS_sendmmsg+0x63/0x90 net/socket.c:2162 do_syscall_64+0x309/0x430 arch/x86/entry/common.c:287 entry_SYSCALL_64_after_hwframe+0x3d/0xa2 This change addresses the issue adding the needed check before accessing the inner header. The ipv4 side of the issue is apparently there since the ipv4 over ipv6 initial support, and the ipv6 side predates git history. Fixes: c4d3efafcc93 ("[IPV6] IP6TUNNEL: Add support to IPv4 over IPv6 tunnel.") Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Reported-by: syzbot+3fde91d4d394747d6db4@syzkaller.appspotmail.com Tested-by: Alexander Potapenko <glider@google.com> Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-19Merge tag 'batadv-net-for-davem-20180919' of git://git.open-mesh.org/linux-mergeDavid S. Miller
Simon Wunderlich says: ==================== pull request for net: batman-adv 2018-09-19 here are some bugfixes which we would like to see integrated into net. We forgot to bump the version number in the last round for net-next, so the belated patch to do that is included - we hope you can adopt it. This will most likely create a merge conflict later when merging into net-next with this rounds net-next patchset, but net-next should keep the 2018.4 version[1]. [1] resolution: --- a/net/batman-adv/main.h +++ b/net/batman-adv/main.h @@ -25,11 +25,7 @@ #define BATADV_DRIVER_DEVICE "batman-adv" #ifndef BATADV_SOURCE_VERSION -<<<<<<< -#define BATADV_SOURCE_VERSION "2018.3" -======= #define BATADV_SOURCE_VERSION "2018.4" ->>>>>>> #endif /* B.A.T.M.A.N. parameters */ Please pull or let me know of any problem! Here are some batman-adv bugfixes: - Avoid ELP information leak, by Sven Eckelmann - Fix sysfs segfault issues, by Sven Eckelmann (2 patches) - Fix locking when adding entries in various lists, by Sven Eckelmann (5 patches) - Fix refcount if queue_work() fails, by Marek Lindner (2 patches) - Fixup forgotten version bump, by Sven Eckelmann ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-18ipv6: fix memory leak on dst->_metricsWei Wang
When dst->_metrics and f6i->fib6_metrics share the same memory, both take reference count on the dst_metrics structure. However, when dst is destroyed, ip6_dst_destroy() only invokes dst_destroy_metrics_generic() which does not take care of READONLY metrics and does not release refcnt. This causes memory leak. Similar to ipv4 logic, the fix is to properly release refcnt and free the memory space pointed by dst->_metrics if refcnt becomes 0. Fixes: 93531c674315 ("net/ipv6: separate handling of FIB entries from dst based routes") Reported-by: Sabrina Dubroca <sd@queasysnail.net> Signed-off-by: Wei Wang <weiwan@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-18Revert "ipv6: fix double refcount of fib6_metrics"Wei Wang
This reverts commit e70a3aad44cc8b24986687ffc98c4a4f6ecf25ea. This change causes use-after-free on dst->_metrics. The crash trace looks like this: [ 97.763269] BUG: KASAN: use-after-free in ip6_mtu+0x116/0x140 [ 97.769038] Read of size 4 at addr ffff881781d2cf84 by task svw_NetThreadEv/8801 [ 97.777954] CPU: 76 PID: 8801 Comm: svw_NetThreadEv Not tainted 4.15.0-smp-DEV #11 [ 97.777956] Hardware name: Default string Default string/Indus_QC_02, BIOS 5.46.4 03/29/2018 [ 97.777957] Call Trace: [ 97.777971] [<ffffffff895709db>] dump_stack+0x4d/0x72 [ 97.777985] [<ffffffff881651df>] print_address_description+0x6f/0x260 [ 97.777997] [<ffffffff88165747>] kasan_report+0x257/0x370 [ 97.778001] [<ffffffff894488e6>] ? ip6_mtu+0x116/0x140 [ 97.778004] [<ffffffff881658b9>] __asan_report_load4_noabort+0x19/0x20 [ 97.778008] [<ffffffff894488e6>] ip6_mtu+0x116/0x140 [ 97.778013] [<ffffffff892bb91e>] tcp_current_mss+0x12e/0x280 [ 97.778016] [<ffffffff892bb7f0>] ? tcp_mtu_to_mss+0x2d0/0x2d0 [ 97.778022] [<ffffffff887b45b8>] ? depot_save_stack+0x138/0x4a0 [ 97.778037] [<ffffffff87c38985>] ? __mmdrop+0x145/0x1f0 [ 97.778040] [<ffffffff881643b1>] ? save_stack+0xb1/0xd0 [ 97.778046] [<ffffffff89264c82>] tcp_send_mss+0x22/0x220 [ 97.778059] [<ffffffff89273a49>] tcp_sendmsg_locked+0x4f9/0x39f0 [ 97.778062] [<ffffffff881642b4>] ? kasan_check_write+0x14/0x20 [ 97.778066] [<ffffffff89273550>] ? tcp_sendpage+0x60/0x60 [ 97.778070] [<ffffffff881cb359>] ? rw_copy_check_uvector+0x69/0x280 [ 97.778075] [<ffffffff8873c65f>] ? import_iovec+0x9f/0x430 [ 97.778078] [<ffffffff88164be7>] ? kasan_slab_free+0x87/0xc0 [ 97.778082] [<ffffffff8873c5c0>] ? memzero_page+0x140/0x140 [ 97.778085] [<ffffffff881642b4>] ? kasan_check_write+0x14/0x20 [ 97.778088] [<ffffffff89276f6c>] tcp_sendmsg+0x2c/0x50 [ 97.778092] [<ffffffff89276f6c>] ? tcp_sendmsg+0x2c/0x50 [ 97.778098] [<ffffffff89352d43>] inet_sendmsg+0x103/0x480 [ 97.778102] [<ffffffff89352c40>] ? inet_gso_segment+0x15b0/0x15b0 [ 97.778105] [<ffffffff890294da>] sock_sendmsg+0xba/0xf0 [ 97.778108] [<ffffffff8902ab6a>] ___sys_sendmsg+0x6ca/0x8e0 [ 97.778113] [<ffffffff87dccac1>] ? hrtimer_try_to_cancel+0x71/0x3b0 [ 97.778116] [<ffffffff8902a4a0>] ? copy_msghdr_from_user+0x3d0/0x3d0 [ 97.778119] [<ffffffff881646d1>] ? memset+0x31/0x40 [ 97.778123] [<ffffffff87a0cff5>] ? schedule_hrtimeout_range_clock+0x165/0x380 [ 97.778127] [<ffffffff87a0ce90>] ? hrtimer_nanosleep_restart+0x250/0x250 [ 97.778130] [<ffffffff87dcc700>] ? __hrtimer_init+0x180/0x180 [ 97.778133] [<ffffffff87dd1f82>] ? ktime_get_ts64+0x172/0x200 [ 97.778137] [<ffffffff8822b8ec>] ? __fget_light+0x8c/0x2f0 [ 97.778141] [<ffffffff8902d5c6>] __sys_sendmsg+0xe6/0x190 [ 97.778144] [<ffffffff8902d5c6>] ? __sys_sendmsg+0xe6/0x190 [ 97.778147] [<ffffffff8902d4e0>] ? SyS_shutdown+0x20/0x20 [ 97.778152] [<ffffffff87cd4370>] ? wake_up_q+0xe0/0xe0 [ 97.778155] [<ffffffff8902d670>] ? __sys_sendmsg+0x190/0x190 [ 97.778158] [<ffffffff8902d683>] SyS_sendmsg+0x13/0x20 [ 97.778162] [<ffffffff87a1600c>] do_syscall_64+0x2ac/0x430 [ 97.778166] [<ffffffff87c17515>] ? do_page_fault+0x35/0x3d0 [ 97.778171] [<ffffffff8960131f>] ? page_fault+0x2f/0x50 [ 97.778174] [<ffffffff89600071>] entry_SYSCALL_64_after_hwframe+0x3d/0xa2 [ 97.778177] RIP: 0033:0x7f83fa36000d [ 97.778178] RSP: 002b:00007f83ef9229e0 EFLAGS: 00000293 ORIG_RAX: 000000000000002e [ 97.778180] RAX: ffffffffffffffda RBX: 0000000000000001 RCX: 00007f83fa36000d [ 97.778182] RDX: 0000000000004000 RSI: 00007f83ef922f00 RDI: 0000000000000036 [ 97.778183] RBP: 00007f83ef923040 R08: 00007f83ef9231f8 R09: 00007f83ef923168 [ 97.778184] R10: 0000000000000000 R11: 0000000000000293 R12: 00007f83f69c5b40 [ 97.778185] R13: 000000000000001c R14: 0000000000000001 R15: 0000000000004000 [ 97.779684] Allocated by task 5919: [ 97.783185] save_stack+0x46/0xd0 [ 97.783187] kasan_kmalloc+0xad/0xe0 [ 97.783189] kmem_cache_alloc_trace+0xdf/0x580 [ 97.783190] ip6_convert_metrics.isra.79+0x7e/0x190 [ 97.783192] ip6_route_info_create+0x60a/0x2480 [ 97.783193] ip6_route_add+0x1d/0x80 [ 97.783195] inet6_rtm_newroute+0xdd/0xf0 [ 97.783198] rtnetlink_rcv_msg+0x641/0xb10 [ 97.783200] netlink_rcv_skb+0x27b/0x3e0 [ 97.783202] rtnetlink_rcv+0x15/0x20 [ 97.783203] netlink_unicast+0x4be/0x720 [ 97.783204] netlink_sendmsg+0x7bc/0xbf0 [ 97.783205] sock_sendmsg+0xba/0xf0 [ 97.783207] ___sys_sendmsg+0x6ca/0x8e0 [ 97.783208] __sys_sendmsg+0xe6/0x190 [ 97.783209] SyS_sendmsg+0x13/0x20 [ 97.783211] do_syscall_64+0x2ac/0x430 [ 97.783213] entry_SYSCALL_64_after_hwframe+0x3d/0xa2 [ 97.784709] Freed by task 0: [ 97.785056] knetbase: Error: /proc/sys/net/core/txcs_enable does not exist [ 97.794497] save_stack+0x46/0xd0 [ 97.794499] kasan_slab_free+0x71/0xc0 [ 97.794500] kfree+0x7c/0xf0 [ 97.794501] fib6_info_destroy_rcu+0x24f/0x310 [ 97.794504] rcu_process_callbacks+0x38b/0x1730 [ 97.794506] __do_softirq+0x1c8/0x5d0 Reported-by: John Sperbeck <jsperbeck@google.com> Signed-off-by: Wei Wang <weiwan@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-18net/smc: fix sizeof to int comparisonYueHaibing
Comparing an int to a size, which is unsigned, causes the int to become unsigned, giving the wrong result. kernel_sendmsg can return a negative error code. Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-18net/smc: no urgent data check for listen socketsKarsten Graul
Don't check a listen socket for pending urgent data in smc_poll(). Signed-off-by: Karsten Graul <kgraul@linux.ibm.com> Signed-off-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-18net/smc: enable fallback for connection abort in state INITUrsula Braun
If a linkgroup is terminated abnormally already due to failing LLC CONFIRM LINK or LLC ADD LINK, fallback to TCP is still possible. In this case do not switch to state SMC_PEERABORTWAIT and do not set sk_err. Signed-off-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-18net/smc: remove duplicate mutex_unlockUrsula Braun
For a failing smc_listen_rdma_finish() smc_listen_decline() is called. If fallback is possible, the new socket is already enqueued to be accepted in smc_listen_decline(). Avoid enqueuing a second time afterwards in this case, otherwise the smc_create_lgr_pending lock is released twice: [ 373.463976] WARNING: bad unlock balance detected! [ 373.463978] 4.18.0-rc7+ #123 Tainted: G O [ 373.463979] ------------------------------------- [ 373.463980] kworker/1:1/30 is trying to release lock (smc_create_lgr_pending) at: [ 373.463990] [<000003ff801205fc>] smc_listen_work+0x22c/0x5d0 [smc] [ 373.463991] but there are no more locks to release! [ 373.463991] other info that might help us debug this: [ 373.463993] 2 locks held by kworker/1:1/30: [ 373.463994] #0: 00000000772cbaed ((wq_completion)"events"){+.+.}, at: process_one_work+0x1ec/0x6b0 [ 373.464000] #1: 000000003ad0894a ((work_completion)(&new_smc->smc_listen_work)){+.+.}, at: process_one_work+0x1ec/0x6b0 [ 373.464003] stack backtrace: [ 373.464005] CPU: 1 PID: 30 Comm: kworker/1:1 Kdump: loaded Tainted: G O 4.18.0-rc7uschi+ #123 [ 373.464007] Hardware name: IBM 2827 H43 738 (LPAR) [ 373.464010] Workqueue: events smc_listen_work [smc] [ 373.464011] Call Trace: [ 373.464015] ([<0000000000114100>] show_stack+0x60/0xd8) [ 373.464019] [<0000000000a8c9bc>] dump_stack+0x9c/0xd8 [ 373.464021] [<00000000001dcaf8>] print_unlock_imbalance_bug+0xf8/0x108 [ 373.464022] [<00000000001e045c>] lock_release+0x114/0x4f8 [ 373.464025] [<0000000000aa87fa>] __mutex_unlock_slowpath+0x4a/0x300 [ 373.464027] [<000003ff801205fc>] smc_listen_work+0x22c/0x5d0 [smc] [ 373.464029] [<0000000000197a68>] process_one_work+0x2a8/0x6b0 [ 373.464030] [<0000000000197ec2>] worker_thread+0x52/0x410 [ 373.464033] [<000000000019fd0e>] kthread+0x15e/0x178 [ 373.464035] [<0000000000aaf58a>] kernel_thread_starter+0x6/0xc [ 373.464052] [<0000000000aaf584>] kernel_thread_starter+0x0/0xc [ 373.464054] INFO: lockdep is turned off. Signed-off-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-18net/smc: fix non-blocking connect problemUrsula Braun
In state SMC_INIT smc_poll() delegates polling to the internal CLC socket. This means, once the connect worker has finished its kernel_connect() step, the poll wake-up may occur. This is not intended. The wake-up should occur from the wake up call in smc_connect_work() after __smc_connect() has finished. Thus in state SMC_INIT this patch now calls sock_poll_wait() on the main SMC socket. Signed-off-by: Ursula Braun <ubraun@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-18NFC: Fix possible memory corruption when handling SHDLC I-Frame commandsSuren Baghdasaryan
When handling SHDLC I-Frame commands "pipe" field used for indexing into an array should be checked before usage. If left unchecked it might access memory outside of the array of size NFC_HCI_MAX_PIPES(127). Malformed NFC HCI frames could be injected by a malicious NFC device communicating with the device being attacked (remote attack vector), or even by an attacker with physical access to the I2C bus such that they could influence the data transfers on that bus (local attack vector). skb->data is controlled by the attacker and has only been sanitized in the most trivial ways (CRC check), therefore we can consider the create_info struct and all of its members to tainted. 'create_info->pipe' with max value of 255 (uint8) is used to take an offset of the hdev->pipes array of 127 elements which can lead to OOB write. Cc: Samuel Ortiz <sameo@linux.intel.com> Cc: Allen Pais <allen.pais@oracle.com> Cc: "David S. Miller" <davem@davemloft.net> Suggested-by: Kevin Deus <kdeus@google.com> Signed-off-by: Suren Baghdasaryan <surenb@google.com> Acked-by: Kees Cook <keescook@chromium.org> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-17net/ipv6: do not copy dst flags on rt initPeter Oskolkov
DST_NOCOUNT in dst_entry::flags tracks whether the entry counts toward route cache size (net->ipv6.sysctl.ip6_rt_max_size). If the flag is NOT set, dst_ops::pcpuc_entries counter is incremented in dist_init() and decremented in dst_destroy(). This flag is tied to allocation/deallocation of dst_entry and should not be copied from another dst/route. Otherwise it can happen that dst_ops::pcpuc_entries counter grows until no new routes can be allocated because the counter reached ip6_rt_max_size due to DST_NOCOUNT not set and thus no counter decrements on gc-ed routes. Fixes: 3b6761d18bc1 ("net/ipv6: Move dst flags to booleans in fib entries") Cc: David Ahern <dsahern@gmail.com> Acked-by: Wei Wang <weiwan@google.com> Signed-off-by: Peter Oskolkov <posk@google.com> Reviewed-by: David Ahern <dsahern@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-17Revert "kcm: remove any offset before parsing messages"David S. Miller
This reverts commit 072222b488bc55cce92ff246bdc10115fd57d3ab. I just read that this causes regressions. Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-17kcm: remove any offset before parsing messagesDominique Martinet
The current code assumes kcm users know they need to look for the strparser offset within their bpf program, which is not documented anywhere and examples laying around do not do. The actual recv function does handle the offset well, so we can create a temporary clone of the skb and pull that one up as required for parsing. The pull itself has a cost if we are pulling beyond the head data, measured to 2-3% latency in a noisy VM with a local client stressing that path. The clone's impact seemed too small to measure. This bug can be exhibited easily by implementing a "trivial" kcm parser taking the first bytes as size, and on the client sending at least two such packets in a single write(). Note that bpf sockmap has the same problem, both for parse and for recv, so it would pulling twice or a real pull within the strparser logic if anyone cares about that. Signed-off-by: Dominique Martinet <asmadeus@codewreck.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-17tls: fix currently broken MSG_PEEK behaviorDaniel Borkmann
In kTLS MSG_PEEK behavior is currently failing, strace example: [pid 2430] socket(AF_INET, SOCK_STREAM, IPPROTO_IP) = 3 [pid 2430] socket(AF_INET, SOCK_STREAM, IPPROTO_IP) = 4 [pid 2430] bind(4, {sa_family=AF_INET, sin_port=htons(0), sin_addr=inet_addr("0.0.0.0")}, 16) = 0 [pid 2430] listen(4, 10) = 0 [pid 2430] getsockname(4, {sa_family=AF_INET, sin_port=htons(38855), sin_addr=inet_addr("0.0.0.0")}, [16]) = 0 [pid 2430] connect(3, {sa_family=AF_INET, sin_port=htons(38855), sin_addr=inet_addr("0.0.0.0")}, 16) = 0 [pid 2430] setsockopt(3, SOL_TCP, 0x1f /* TCP_??? */, [7564404], 4) = 0 [pid 2430] setsockopt(3, 0x11a /* SOL_?? */, 1, "\3\0033\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0"..., 40) = 0 [pid 2430] accept(4, {sa_family=AF_INET, sin_port=htons(49636), sin_addr=inet_addr("127.0.0.1")}, [16]) = 5 [pid 2430] setsockopt(5, SOL_TCP, 0x1f /* TCP_??? */, [7564404], 4) = 0 [pid 2430] setsockopt(5, 0x11a /* SOL_?? */, 2, "\3\0033\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0"..., 40) = 0 [pid 2430] close(4) = 0 [pid 2430] sendto(3, "test_read_peek", 14, 0, NULL, 0) = 14 [pid 2430] sendto(3, "_mult_recs\0", 11, 0, NULL, 0) = 11 [pid 2430] recvfrom(5, "test_read_peektest_read_peektest"..., 64, MSG_PEEK, NULL, NULL) = 64 As can be seen from strace, there are two TLS records sent, i) 'test_read_peek' and ii) '_mult_recs\0' where we end up peeking 'test_read_peektest_read_peektest'. This is clearly wrong, and what happens is that given peek cannot call into tls_sw_advance_skb() to unpause strparser and proceed with the next skb, we end up looping over the current one, copying the 'test_read_peek' over and over into the user provided buffer. Here, we can only peek into the currently held skb (current, full TLS record) as otherwise we would end up having to hold all the original skb(s) (depending on the peek depth) in a separate queue when unpausing strparser to process next records, minimally intrusive is to return only up to the current record's size (which likely was what c46234ebb4d1 ("tls: RX path for ktls") originally intended as well). Thus, after patch we properly peek the first record: [pid 2046] wait4(2075, <unfinished ...> [pid 2075] socket(AF_INET, SOCK_STREAM, IPPROTO_IP) = 3 [pid 2075] socket(AF_INET, SOCK_STREAM, IPPROTO_IP) = 4 [pid 2075] bind(4, {sa_family=AF_INET, sin_port=htons(0), sin_addr=inet_addr("0.0.0.0")}, 16) = 0 [pid 2075] listen(4, 10) = 0 [pid 2075] getsockname(4, {sa_family=AF_INET, sin_port=htons(55115), sin_addr=inet_addr("0.0.0.0")}, [16]) = 0 [pid 2075] connect(3, {sa_family=AF_INET, sin_port=htons(55115), sin_addr=inet_addr("0.0.0.0")}, 16) = 0 [pid 2075] setsockopt(3, SOL_TCP, 0x1f /* TCP_??? */, [7564404], 4) = 0 [pid 2075] setsockopt(3, 0x11a /* SOL_?? */, 1, "\3\0033\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0"..., 40) = 0 [pid 2075] accept(4, {sa_family=AF_INET, sin_port=htons(45732), sin_addr=inet_addr("127.0.0.1")}, [16]) = 5 [pid 2075] setsockopt(5, SOL_TCP, 0x1f /* TCP_??? */, [7564404], 4) = 0 [pid 2075] setsockopt(5, 0x11a /* SOL_?? */, 2, "\3\0033\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0\0"..., 40) = 0 [pid 2075] close(4) = 0 [pid 2075] sendto(3, "test_read_peek", 14, 0, NULL, 0) = 14 [pid 2075] sendto(3, "_mult_recs\0", 11, 0, NULL, 0) = 11 [pid 2075] recvfrom(5, "test_read_peek", 64, MSG_PEEK, NULL, NULL) = 14 Fixes: c46234ebb4d1 ("tls: RX path for ktls") Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-17ipv6: fix possible use-after-free in ip6_xmit()Eric Dumazet
In the unlikely case ip6_xmit() has to call skb_realloc_headroom(), we need to call skb_set_owner_w() before consuming original skb, otherwise we risk a use-after-free. Bring IPv6 in line with what we do in IPv4 to fix this. Fixes: 1da177e4c3f41 ("Linux-2.6.12-rc2") Signed-off-by: Eric Dumazet <edumazet@google.com> Reported-by: syzbot <syzkaller@googlegroups.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-16Merge git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpfDavid S. Miller
Daniel Borkmann says: ==================== pull-request: bpf 2018-09-16 The following pull-request contains BPF updates for your *net* tree. The main changes are: 1) Fix end boundary calculation in BTF for the type section, from Martin. 2) Fix and revert subtraction of pointers that was accidentally allowed for unprivileged programs, from Alexei. 3) Fix bpf_msg_pull_data() helper by using __GFP_COMP in order to avoid a warning in linearizing sg pages into a single one for large allocs, from Tushar. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-16udp6: add missing checks on edumux packet processingPaolo Abeni
Currently the UDPv6 early demux rx code path lacks some mandatory checks, already implemented into the normal RX code path - namely the checksum conversion and no_check6_rx check. Similar to the previous commit, we move the common processing to an UDPv6 specific helper and call it from both edemux code path and normal code path. In respect to the UDPv4, we need to add an explicit check for non zero csum according to no_check6_rx value. Reported-by: Jianlin Shi <jishi@redhat.com> Suggested-by: Xin Long <lucien.xin@gmail.com> Fixes: c9f2c1ae123a ("udp6: fix socket leak on early demux") Fixes: 2abb7cdc0dc8 ("udp: Add support for doing checksum unnecessary conversion") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-16udp4: fix IP_CMSG_CHECKSUM for connected socketsPaolo Abeni
commit 2abb7cdc0dc8 ("udp: Add support for doing checksum unnecessary conversion") left out the early demux path for connected sockets. As a result IP_CMSG_CHECKSUM gives wrong values for such socket when GRO is not enabled/available. This change addresses the issue by moving the csum conversion to a common helper and using such helper in both the default and the early demux rx path. Fixes: 2abb7cdc0dc8 ("udp: Add support for doing checksum unnecessary conversion") Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-14batman-adv: Increase version number to 2018.3Sven Eckelmann
Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
2018-09-14net/sched: act_sample: fix NULL dereference in the data pathDavide Caratti
Matteo reported the following splat, testing the datapath of TC 'sample': BUG: KASAN: null-ptr-deref in tcf_sample_act+0xc4/0x310 Read of size 8 at addr 0000000000000000 by task nc/433 CPU: 0 PID: 433 Comm: nc Not tainted 4.19.0-rc3-kvm #17 Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS ?-20180531_142017-buildhw-08.phx2.fedoraproject.org-1.fc28 04/01/2014 Call Trace: kasan_report.cold.6+0x6c/0x2fa tcf_sample_act+0xc4/0x310 ? dev_hard_start_xmit+0x117/0x180 tcf_action_exec+0xa3/0x160 tcf_classify+0xdd/0x1d0 htb_enqueue+0x18e/0x6b0 ? deref_stack_reg+0x7a/0xb0 ? htb_delete+0x4b0/0x4b0 ? unwind_next_frame+0x819/0x8f0 ? entry_SYSCALL_64_after_hwframe+0x44/0xa9 __dev_queue_xmit+0x722/0xca0 ? unwind_get_return_address_ptr+0x50/0x50 ? netdev_pick_tx+0xe0/0xe0 ? save_stack+0x8c/0xb0 ? kasan_kmalloc+0xbe/0xd0 ? __kmalloc_track_caller+0xe4/0x1c0 ? __kmalloc_reserve.isra.45+0x24/0x70 ? __alloc_skb+0xdd/0x2e0 ? sk_stream_alloc_skb+0x91/0x3b0 ? tcp_sendmsg_locked+0x71b/0x15a0 ? tcp_sendmsg+0x22/0x40 ? __sys_sendto+0x1b0/0x250 ? __x64_sys_sendto+0x6f/0x80 ? do_syscall_64+0x5d/0x150 ? entry_SYSCALL_64_after_hwframe+0x44/0xa9 ? __sys_sendto+0x1b0/0x250 ? __x64_sys_sendto+0x6f/0x80 ? do_syscall_64+0x5d/0x150 ? entry_SYSCALL_64_after_hwframe+0x44/0xa9 ip_finish_output2+0x495/0x590 ? ip_copy_metadata+0x2e0/0x2e0 ? skb_gso_validate_network_len+0x6f/0x110 ? ip_finish_output+0x174/0x280 __tcp_transmit_skb+0xb17/0x12b0 ? __tcp_select_window+0x380/0x380 tcp_write_xmit+0x913/0x1de0 ? __sk_mem_schedule+0x50/0x80 tcp_sendmsg_locked+0x49d/0x15a0 ? tcp_rcv_established+0x8da/0xa30 ? tcp_set_state+0x220/0x220 ? clear_user+0x1f/0x50 ? iov_iter_zero+0x1ae/0x590 ? __fget_light+0xa0/0xe0 tcp_sendmsg+0x22/0x40 __sys_sendto+0x1b0/0x250 ? __ia32_sys_getpeername+0x40/0x40 ? _copy_to_user+0x58/0x70 ? poll_select_copy_remaining+0x176/0x200 ? __pollwait+0x1c0/0x1c0 ? ktime_get_ts64+0x11f/0x140 ? kern_select+0x108/0x150 ? core_sys_select+0x360/0x360 ? vfs_read+0x127/0x150 ? kernel_write+0x90/0x90 __x64_sys_sendto+0x6f/0x80 do_syscall_64+0x5d/0x150 entry_SYSCALL_64_after_hwframe+0x44/0xa9 RIP: 0033:0x7fefef2b129d Code: ff ff ff ff eb b6 0f 1f 80 00 00 00 00 48 8d 05 51 37 0c 00 41 89 ca 8b 00 85 c0 75 20 45 31 c9 45 31 c0 b8 2c 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 6b f3 c3 66 0f 1f 84 00 00 00 00 00 41 56 41 RSP: 002b:00007fff2f5350c8 EFLAGS: 00000246 ORIG_RAX: 000000000000002c RAX: ffffffffffffffda RBX: 000056118d60c120 RCX: 00007fefef2b129d RDX: 0000000000002000 RSI: 000056118d629320 RDI: 0000000000000003 RBP: 000056118d530370 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000002000 R13: 000056118d5c2a10 R14: 000056118d5c2a10 R15: 000056118d5303b8 tcf_sample_act() tried to update its per-cpu stats, but tcf_sample_init() forgot to allocate them, because tcf_idr_create() was called with a wrong value of 'cpustats'. Setting it to true proved to fix the reported crash. Reported-by: Matteo Croce <mcroce@redhat.com> Fixes: 65a206c01e8e ("net/sched: Change act_api and act_xxx modules to use IDR") Fixes: 5c5670fae430 ("net/sched: Introduce sample tc action") Tested-by: Matteo Croce <mcroce@redhat.com> Signed-off-by: Davide Caratti <dcaratti@redhat.com> Acked-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-13socket: fix struct ifreq size in compat ioctlJohannes Berg
As reported by Reobert O'Callahan, since Viro's commit to kill dev_ifsioc() we attempt to copy too much data in compat mode, which may lead to EFAULT when the 32-bit version of struct ifreq sits at/near the end of a page boundary, and the next page isn't mapped. Fix this by passing the approprate compat/non-compat size to copy and using that, as before the dev_ifsioc() removal. This works because only the embedded "struct ifmap" has different size, and this is only used in SIOCGIFMAP/SIOCSIFMAP which has a different handler. All other parts of the union are naturally compatible. This fixes https://bugzilla.kernel.org/show_bug.cgi?id=199469. Fixes: bf4405737f9f ("kill dev_ifsioc()") Reported-by: Robert O'Callahan <robert@ocallahan.org> Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-13gso_segment: Reset skb->mac_len after modifying network headerToke Høiland-Jørgensen
When splitting a GSO segment that consists of encapsulated packets, the skb->mac_len of the segments can end up being set wrong, causing packet drops in particular when using act_mirred and ifb interfaces in combination with a qdisc that splits GSO packets. This happens because at the time skb_segment() is called, network_header will point to the inner header, throwing off the calculation in skb_reset_mac_len(). The network_header is subsequently adjust by the outer IP gso_segment handlers, but they don't set the mac_len. Fix this by adding skb_reset_mac_len() calls to both the IPv4 and IPv6 gso_segment handlers, after they modify the network_header. Many thanks to Eric Dumazet for his help in identifying the cause of the bug. Acked-by: Dave Taht <dave.taht@gmail.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-13Merge branch 'for-upstream' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth Johan Hedberg says: ==================== pull request: bluetooth 2018-09-13 A few Bluetooth fixes for the 4.19-rc series: - Fixed rw_semaphore leak in hci_ldisc - Fixed local Out-of-Band pairing data handling Let me know if there are any issues pulling. Thanks. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-13tls: clear key material from kernel memory when do_tls_setsockopt_conf failsSabrina Dubroca
Fixes: 3c4d7559159b ("tls: kernel TLS support") Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-13tls: zero the crypto information from tls_context before freeingSabrina Dubroca
This contains key material in crypto_send_aes_gcm_128 and crypto_recv_aes_gcm_128. Introduce union tls_crypto_context, and replace the two identical unions directly embedded in struct tls_context with it. We can then use this union to clean up the memory in the new tls_ctx_free() function. Fixes: 3c4d7559159b ("tls: kernel TLS support") Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-13tls: don't copy the key out of tls12_crypto_info_aes_gcm_128Sabrina Dubroca
There's no need to copy the key to an on-stack buffer before calling crypto_aead_setkey(). Fixes: 3c4d7559159b ("tls: kernel TLS support") Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-13neighbour: confirm neigh entries when ARP packet is receivedVasily Khoruzhick
Update 'confirmed' timestamp when ARP packet is received. It shouldn't affect locktime logic and anyway entry can be confirmed by any higher-layer protocol. Thus it makes sense to confirm it when ARP packet is received. Fixes: 77d7123342dc ("neighbour: update neigh timestamps iff update is effective") Signed-off-by: Vasily Khoruzhick <vasilykh@arista.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-13net: rtnl_configure_link: fix dev flags changes arg to __dev_notify_flagsRoopa Prabhu
This fix addresses https://bugzilla.kernel.org/show_bug.cgi?id=201071 Commit 5025f7f7d506 wrongly relied on __dev_change_flags to notify users of dev flag changes in the case when dev->rtnl_link_state = RTNL_LINK_INITIALIZED. Fix it by indicating flag changes explicitly to __dev_notify_flags. Fixes: 5025f7f7d506 ("rtnetlink: add rtnl_link_state check in rtnl_configure_link") Reported-By: Liam mcbirnie <liam.mcbirnie@boeing.com> Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-13net_sched: notify filter deletion when deleting a chainCong Wang
When we delete a chain of filters, we need to notify user-space we are deleting each filters in this chain too. Fixes: 32a4f5ecd738 ("net: sched: introduce chain object to uapi") Cc: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-13ipv6: use rt6_info members when dst is set in rt6_fill_nodeXin Long
In inet6_rtm_getroute, since Commit 93531c674315 ("net/ipv6: separate handling of FIB entries from dst based routes"), it has used rt->from to dump route info instead of rt. However for some route like cache, some of its information like flags or gateway is not the same as that of the 'from' one. It caused 'ip route get' to dump the wrong route information. In Jianlin's testing, the output information even lost the expiration time for a pmtu route cache due to the wrong fib6_flags. So change to use rt6_info members for dst addr, src addr, flags and gateway when it tries to dump a route entry without fibmatch set. v1->v2: - not use rt6i_prefsrc. - also fix the gw dump issue. Fixes: 93531c674315 ("net/ipv6: separate handling of FIB entries from dst based routes") Reported-by: Jianlin Shi <jishi@redhat.com> Signed-off-by: Xin Long <lucien.xin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-12bpf: use __GFP_COMP while allocating pageTushar Dave
Helper bpg_msg_pull_data() can allocate multiple pages while linearizing multiple scatterlist elements into one shared page. However, if the shared page has size > PAGE_SIZE, using copy_page_to_iter() causes below warning. e.g. [ 6367.019832] WARNING: CPU: 2 PID: 7410 at lib/iov_iter.c:825 page_copy_sane.part.8+0x0/0x8 To avoid above warning, use __GFP_COMP while allocating multiple contiguous pages. Fixes: 015632bb30da ("bpf: sk_msg program helper bpf_sk_msg_pull_data") Signed-off-by: Tushar Dave <tushar.n.dave@oracle.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
2018-09-12tipc: check return value of __tipc_dump_start()Cong Wang
When __tipc_dump_start() fails with running out of memory, we have no reason to continue, especially we should avoid calling tipc_dump_done(). Fixes: 8f5c5fcf3533 ("tipc: call start and done ops directly in __tipc_nl_compat_dumpit()") Reported-and-tested-by: syzbot+3f8324abccfbf8c74a9f@syzkaller.appspotmail.com Cc: Jon Maloy <jon.maloy@ericsson.com> Cc: Ying Xue <ying.xue@windriver.com> Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Acked-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-12rds: fix two RCU related problemsCong Wang
When a rds sock is bound, it is inserted into the bind_hash_table which is protected by RCU. But when releasing rds sock, after it is removed from this hash table, it is freed immediately without respecting RCU grace period. This could cause some use-after-free as reported by syzbot. Mark the rds sock with SOCK_RCU_FREE before inserting it into the bind_hash_table, so that it would be always freed after a RCU grace period. The other problem is in rds_find_bound(), the rds sock could be freed in between rhashtable_lookup_fast() and rds_sock_addref(), so we need to extend RCU read lock protection in rds_find_bound() to close this race condition. Reported-and-tested-by: syzbot+8967084bcac563795dc6@syzkaller.appspotmail.com Reported-by: syzbot+93a5839deb355537440f@syzkaller.appspotmail.com Cc: Sowmini Varadhan <sowmini.varadhan@oracle.com> Cc: Santosh Shilimkar <santosh.shilimkar@oracle.com> Cc: rds-devel@oss.oracle.com Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com> Acked-by: Santosh Shilimkar <santosh.shilimkar@oarcle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-11erspan: fix error handling for erspan tunnelHaishuang Yan
When processing icmp unreachable message for erspan tunnel, tunnel id should be erspan_net_id instead of ipgre_net_id. Fixes: 84e54fe0a5ea ("gre: introduce native tunnel support for ERSPAN") Cc: William Tu <u9012063@gmail.com> Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com> Acked-by: William Tu <u9012063@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-11erspan: return PACKET_REJECT when the appropriate tunnel is not foundHaishuang Yan
If erspan tunnel hasn't been established, we'd better send icmp port unreachable message after receive erspan packets. Fixes: 84e54fe0a5ea ("gre: introduce native tunnel support for ERSPAN") Cc: William Tu <u9012063@gmail.com> Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com> Acked-by: William Tu <u9012063@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-11tcp: rate limit synflood warnings furtherWillem de Bruijn
Convert pr_info to net_info_ratelimited to limit the total number of synflood warnings. Commit 946cedccbd73 ("tcp: Change possible SYN flooding messages") rate limits synflood warnings to one per listener. Workloads that open many listener sockets can still see a high rate of log messages. Syzkaller is one frequent example. Signed-off-by: Willem de Bruijn <willemb@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-11Merge git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nfDavid S. Miller
Pablo Neira Ayuso says: ==================== Netfilter fixes for net The following patchset contains Netfilter fixes for you net tree: 1) Remove duplicated include at the end of UDP conntrack, from Yue Haibing. 2) Restore conntrack dependency on xt_cluster, from Martin Willi. 3) Fix splat with GSO skbs from the checksum target, from Florian Westphal. 4) Rework ct timeout support, the template strategy to attach custom timeouts is not correct since it will not work in conjunction with conntrack zones and we have a possible free after use when removing the rule due to missing refcounting. To fix these problems, do not use conntrack template at all and set custom timeout on the already valid conntrack object. This fix comes with a preparation patch to simplify timeout adjustment by initializating the first position of the timeout array for all of the existing trackers. Patchset from Florian Westphal. 5) Fix missing dependency on from IPv4 chain NAT type, from Florian. 6) Release chain reference counter from the flush path, from Taehee Yoo. 7) After flushing an iptables ruleset, conntrack hooks are unregistered and entries are left stale to be cleaned up by the timeout garbage collector. No TCP tracking is done on established flows by this time. If ruleset is reloaded, then hooks are registered again and TCP tracking is restored, which considers packets to be invalid. Clear window tracking to exercise TCP flow pickup from the middle given that history is lost for us. Again from Florian. 8) Fix crash from netlink interface with CONFIG_NF_CONNTRACK_TIMEOUT=y and CONFIG_NF_CT_NETLINK_TIMEOUT=n. 9) Broken CT target due to returning incorrect type from ctnl_timeout_find_get(). 10) Solve conntrack clash on NF_REPEAT verdicts too, from Michal Vaner. 11) Missing conversion of hashlimit sysctl interface to new API, from Cong Wang. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-11Bluetooth: Use correct tfm to generate OOB dataMatias Karhumaa
In case local OOB data was generated and other device initiated pairing claiming that it has got OOB data, following crash occurred: [ 222.847853] general protection fault: 0000 [#1] SMP PTI [ 222.848025] CPU: 1 PID: 42 Comm: kworker/u5:0 Tainted: G C 4.18.0-custom #4 [ 222.848158] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006 [ 222.848307] Workqueue: hci0 hci_rx_work [bluetooth] [ 222.848416] RIP: 0010:compute_ecdh_secret+0x5a/0x270 [bluetooth] [ 222.848540] Code: 0c af f5 48 8b 3d 46 de f0 f6 ba 40 00 00 00 be c0 00 60 00 e8 b7 7b c5 f5 48 85 c0 0f 84 ea 01 00 00 48 89 c3 e8 16 0c af f5 <49> 8b 47 38 be c0 00 60 00 8b 78 f8 48 83 c7 48 e8 51 84 c5 f5 48 [ 222.848914] RSP: 0018:ffffb1664087fbc0 EFLAGS: 00010293 [ 222.849021] RAX: ffff8a5750d7dc00 RBX: ffff8a5671096780 RCX: ffffffffc08bc32a [ 222.849111] RDX: 0000000000000000 RSI: 00000000006000c0 RDI: ffff8a5752003800 [ 222.849192] RBP: ffffb1664087fc60 R08: ffff8a57525280a0 R09: ffff8a5752003800 [ 222.849269] R10: ffffb1664087fc70 R11: 0000000000000093 R12: ffff8a5674396e00 [ 222.849350] R13: ffff8a574c2e79aa R14: ffff8a574c2e796a R15: 020e0e100d010101 [ 222.849429] FS: 0000000000000000(0000) GS:ffff8a5752500000(0000) knlGS:0000000000000000 [ 222.849518] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 222.849586] CR2: 000055856016a038 CR3: 0000000110d2c005 CR4: 00000000000606e0 [ 222.849671] Call Trace: [ 222.849745] ? sc_send_public_key+0x110/0x2a0 [bluetooth] [ 222.849825] ? sc_send_public_key+0x115/0x2a0 [bluetooth] [ 222.849925] smp_recv_cb+0x959/0x2490 [bluetooth] [ 222.850023] ? _cond_resched+0x19/0x40 [ 222.850105] ? mutex_lock+0x12/0x40 [ 222.850202] l2cap_recv_frame+0x109d/0x3420 [bluetooth] [ 222.850315] ? l2cap_recv_frame+0x109d/0x3420 [bluetooth] [ 222.850426] ? __switch_to_asm+0x34/0x70 [ 222.850515] ? __switch_to_asm+0x40/0x70 [ 222.850625] ? __switch_to_asm+0x34/0x70 [ 222.850724] ? __switch_to_asm+0x40/0x70 [ 222.850786] ? __switch_to_asm+0x34/0x70 [ 222.850846] ? __switch_to_asm+0x40/0x70 [ 222.852581] ? __switch_to_asm+0x34/0x70 [ 222.854976] ? __switch_to_asm+0x40/0x70 [ 222.857475] ? __switch_to_asm+0x40/0x70 [ 222.859775] ? __switch_to_asm+0x34/0x70 [ 222.861218] ? __switch_to_asm+0x40/0x70 [ 222.862327] ? __switch_to_asm+0x34/0x70 [ 222.863758] l2cap_recv_acldata+0x266/0x3c0 [bluetooth] [ 222.865122] hci_rx_work+0x1c9/0x430 [bluetooth] [ 222.867144] process_one_work+0x210/0x4c0 [ 222.868248] worker_thread+0x41/0x4d0 [ 222.869420] kthread+0x141/0x160 [ 222.870694] ? process_one_work+0x4c0/0x4c0 [ 222.871668] ? kthread_create_worker_on_cpu+0x90/0x90 [ 222.872896] ret_from_fork+0x35/0x40 [ 222.874132] Modules linked in: algif_hash algif_skcipher af_alg rfcomm bnep btusb btrtl btbcm btintel snd_intel8x0 cmac intel_rapl_perf vboxvideo(C) snd_ac97_codec bluetooth ac97_bus joydev ttm snd_pcm ecdh_generic drm_kms_helper snd_timer snd input_leds drm serio_raw fb_sys_fops soundcore syscopyarea sysfillrect sysimgblt mac_hid sch_fq_codel ib_iser rdma_cm iw_cm ib_cm ib_core iscsi_tcp libiscsi_tcp libiscsi scsi_transport_iscsi ip_tables x_tables autofs4 btrfs zstd_compress raid10 raid456 async_raid6_recov async_memcpy async_pq async_xor async_tx xor raid6_pq libcrc32c raid1 raid0 multipath linear hid_generic usbhid hid crct10dif_pclmul crc32_pclmul ghash_clmulni_intel pcbc aesni_intel aes_x86_64 crypto_simd cryptd glue_helper ahci psmouse libahci i2c_piix4 video e1000 pata_acpi [ 222.883153] fbcon_switch: detected unhandled fb_set_par error, error code -16 [ 222.886774] fbcon_switch: detected unhandled fb_set_par error, error code -16 [ 222.890503] ---[ end trace 6504aa7a777b5316 ]--- [ 222.890541] RIP: 0010:compute_ecdh_secret+0x5a/0x270 [bluetooth] [ 222.890551] Code: 0c af f5 48 8b 3d 46 de f0 f6 ba 40 00 00 00 be c0 00 60 00 e8 b7 7b c5 f5 48 85 c0 0f 84 ea 01 00 00 48 89 c3 e8 16 0c af f5 <49> 8b 47 38 be c0 00 60 00 8b 78 f8 48 83 c7 48 e8 51 84 c5 f5 48 [ 222.890555] RSP: 0018:ffffb1664087fbc0 EFLAGS: 00010293 [ 222.890561] RAX: ffff8a5750d7dc00 RBX: ffff8a5671096780 RCX: ffffffffc08bc32a [ 222.890565] RDX: 0000000000000000 RSI: 00000000006000c0 RDI: ffff8a5752003800 [ 222.890571] RBP: ffffb1664087fc60 R08: ffff8a57525280a0 R09: ffff8a5752003800 [ 222.890576] R10: ffffb1664087fc70 R11: 0000000000000093 R12: ffff8a5674396e00 [ 222.890581] R13: ffff8a574c2e79aa R14: ffff8a574c2e796a R15: 020e0e100d010101 [ 222.890586] FS: 0000000000000000(0000) GS:ffff8a5752500000(0000) knlGS:0000000000000000 [ 222.890591] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 222.890594] CR2: 000055856016a038 CR3: 0000000110d2c005 CR4: 00000000000606e0 This commit fixes a bug where invalid pointer to crypto tfm was used for SMP SC ECDH calculation when OOB was in use. Solution is to use same crypto tfm than when generating OOB material on generate_oob() function. This bug was introduced in commit c0153b0b901a ("Bluetooth: let the crypto subsystem generate the ecc privkey"). Bug was found by fuzzing kernel SMP implementation using Synopsys Defensics. Signed-off-by: Matias Karhumaa <matias.karhumaa@gmail.com> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-09-11Bluetooth: SMP: Fix trying to use non-existent local OOB dataJohan Hedberg
A remote device may claim that it has received our OOB data, even though we never geneated it. Add a new flag to track whether we actually have OOB data, and ignore the remote peer's flag if haven't generated OOB data. Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-12 11:38:58 +0000