| Age | Commit message (Collapse) | Author |
|---|
|
Be sure that packet.sklist initialized in net_init hook was return
to initial state.
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Vasily Averin <vvs@virtuozzo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
DSA now uses one of the symbols exported by the bridge,
br_vlan_enabled(). This has a stub, if the bridge is not
enabled. However, if the bridge is enabled, we cannot have DSA built
in and the bridge as a module, otherwise we get undefined symbols at
link time:
net/dsa/port.o: In function `dsa_port_vlan_add':
net/dsa/port.c:255: undefined reference to `br_vlan_enabled'
net/dsa/port.o: In function `dsa_port_vlan_del':
net/dsa/port.c:270: undefined reference to `br_vlan_enabled'
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch is to remove some useless codes of redirect and fix some
indents on ip4ip6 and ip6ip6's err_handlers.
Note that redirect icmp packet is already processed in ip6_tnl_err,
the old redirect codes in ip4ip6_err actually never worked even
before this patch. Besides, there's no need to send redirect to
user's sk, it's for lower dst, so just remove it in this patch.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The same improvement in "ip6_gre: process toobig in a better way"
is needed by ip4ip6 and ip6ip6 as well.
Note that ip4ip6 and ip6ip6 will also update sk dst pmtu in their
err_handlers. Like I said before, gre6 could not do this as it's
inner proto is not certain. But for all of them, sk dst pmtu will
be updated in tx path if in need.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The same process for redirect in "ip6_gre: add the process for redirect
in ip6gre_err" is needed by ip4ip6 and ip6ip6 as well.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now ip6gre processes toobig icmp packet by setting gre dev's mtu in
ip6gre_err, which would cause few things not good:
- It couldn't set mtu with dev_set_mtu due to it's not in user context,
which causes route cache and idev->cnf.mtu6 not to be updated.
- It has to update sk dst pmtu in tx path according to gredev->mtu for
ip6gre, while it updates pmtu again according to lower dst pmtu in
ip6_tnl_xmit.
- To change dev->mtu by toobig icmp packet is not a good idea, it should
only work on pmtu.
This patch is to process toobig by updating the lower dst's pmtu, as later
sk dst pmtu will be updated in ip6_tnl_xmit, the same way as in ip4gre.
Note that gre dev's mtu will not be updated any more, it doesn't make any
sense to change dev's mtu after receiving a toobig packet.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch is to add redirect icmp packet process for ip6gre by
calling ip6_redirect() in ip6gre_err(), as in vti6_err.
Prior to this patch, there's even no route cache generated after
receiving redirect.
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sameo/nfc-next
Samuel Ortiz says:
====================
NFC 4.15 pull request
This is the NFC pull request for 4.15. We have:
- A new netlink command for explicitly deactivating NFC targets
- i2c constification for all NFC drivers
- One NFC device allocation error path fix
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implements OVS kernel meter action support.
Signed-off-by: Andy Zhou <azhou@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
OVS kernel datapath so far does not support Openflow meter action.
This is the first stab at adding kernel datapath meter support.
This implementation supports only drop band type.
Signed-off-by: Andy Zhou <azhou@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Later patches will invoke get_dp() outside of datapath.c. Export it.
Signed-off-by: Andy Zhou <azhou@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a new type: DSA_TAG_PROTO_PREPEND which allows us to support for the
4-bytes Broadcom tag that we already support, but in a format where it
is pre-pended to the packet instead of located between the MAC SA and
the Ethertyper (DSA_TAG_PROTO_BRCM).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation for supporting the same Broadcom tag format, but instead
of inserted between the MAC SA and EtherType, prepended to the Ethernet
frame, restructure the code a little bit to make that possible and take
an offset parameter.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A number of drivers want to check whether the configured CPU port is a
possible configuration for enabling tagging, pass down the CPU port
number so they verify that.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
gcc-4.4.4 (at lest) has issues with initializers and anonymous unions:
net/sched/sch_red.c: In function 'red_dump_offload':
net/sched/sch_red.c:282: error: unknown field 'stats' specified in initializer
net/sched/sch_red.c:282: warning: initialization makes integer from pointer without a cast
net/sched/sch_red.c:283: error: unknown field 'stats' specified in initializer
net/sched/sch_red.c:283: warning: initialization makes integer from pointer without a cast
net/sched/sch_red.c: In function 'red_dump_stats':
net/sched/sch_red.c:352: error: unknown field 'xstats' specified in initializer
net/sched/sch_red.c:352: warning: initialization makes integer from pointer without a cast
Work around this.
Fixes: 602f3baf2218 ("net_sch: red: Add offload ability to RED qdisc")
Cc: Nogah Frankel <nogahf@mellanox.com>
Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Simon Horman <simon.horman@netronome.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The way people generally use netlink_dump is that they fill in the skb
as much as possible, breaking when nla_put returns an error. Then, they
get called again and start filling out the next skb, and again, and so
forth. The mechanism at work here is the ability for the iterative
dumping function to detect when the skb is filled up and not fill it
past the brim, waiting for a fresh skb for the rest of the data.
However, if the attributes are small and nicely packed, it is possible
that a dump callback function successfully fills in attributes until the
skb is of size 4080 (libmnl's default page-sized receive buffer size).
The dump function completes, satisfied, and then, if it happens to be
that this is actually the last skb, and no further ones are to be sent,
then netlink_dump will add on the NLMSG_DONE part:
nlh = nlmsg_put_answer(skb, cb, NLMSG_DONE, sizeof(len), NLM_F_MULTI);
It is very important that netlink_dump does this, of course. However, in
this example, that call to nlmsg_put_answer will fail, because the
previous filling by the dump function did not leave it enough room. And
how could it possibly have done so? All of the nla_put variety of
functions simply check to see if the skb has enough tailroom,
independent of the context it is in.
In order to keep the important assumptions of all netlink dump users, it
is therefore important to give them an skb that has this end part of the
tail already reserved, so that the call to nlmsg_put_answer does not
fail. Otherwise, library authors are forced to find some bizarre sized
receive buffer that has a large modulo relative to the common sizes of
messages received, which is ugly and buggy.
This patch thus saves the NLMSG_DONE for an additional message, for the
case that things are dangerously close to the brim. This requires
keeping track of the errno from ->dump() across calls.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Slotting is a crude approximation of the behaviors of shared media such
as cable, wifi, and LTE, which gather up a bunch of packets within a
varying delay window and deliver them, relative to that, nearly all at
once.
It works within the existing loss, duplication, jitter and delay
parameters of netem. Some amount of inherent latency must be specified,
regardless.
The new "slot" parameter specifies a minimum and maximum delay between
transmission attempts.
The "bytes" and "packets" parameters can be used to limit the amount of
information transferred per slot.
Examples of use:
tc qdisc add dev eth0 root netem delay 200us \
slot 800us 10ms bytes 64k packets 42
A more correct example, using stacked netem instances and a packet limit
to emulate a tail drop wifi queue with slots and variable packet
delivery, with a 200Mbit isochronous underlying rate, and 20ms path
delay:
tc qdisc add dev eth0 root handle 1: netem delay 20ms rate 200mbit \
limit 10000
tc qdisc add dev eth0 parent 1:1 handle 10:1 netem delay 200us \
slot 800us 10ms bytes 64k packets 42 limit 512
Signed-off-by: Dave Taht <dave.taht@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
netem userspace has long relied on a horrible /proc/net/psched hack
to translate the current notion of "ticks" to nanoseconds.
Expressing latency and jitter instead, in well defined nanoseconds,
increases the dynamic range of emulated delays and jitter in netem.
It will also ease a transition where reducing a tick to nsec
equivalence would constrain the max delay in prior versions of
netem to only 4.3 seconds.
Signed-off-by: Dave Taht <dave.taht@gmail.com>
Suggested-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Upgrade the internal netem scheduler to use nanoseconds rather than
ticks throughout.
Convert to and from the std "ticks" userspace api automatically,
while allowing for finer grained scheduling to take place.
Signed-off-by: Dave Taht <dave.taht@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Avoid traversing the list of mr6_tables (which requires the
rtnl_lock) in ip6mr_sk_done(), when we know in advance that
a match will not be found.
This can happen when rawv6_close()/ip6mr_sk_done() is invoked
on non-mroute6 sockets.
This patch helps reduce rtnl_lock contention when destroying
a large number of net namespaces, each having a non-mroute6
raw socket.
v2: same patch, only fixed subject line and expanded comment.
Signed-off-by: Francesco Ruggeri <fruggeri@arista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
ip6_frag_id was only used by UFO, which has been removed.
ipv6_proxy_select_ident() only existed to set ip6_frag_id and has no
in-tree callers.
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The last user of .tunnel_sock is pppol2tp_connect() which defensively
uses it to verify internal data consistency.
This check isn't necessary: l2tp_session_get() guarantees that the
returned session belongs to the tunnel passed as parameter. And
.tunnel_sock is never updated, so checking that it still points to
the parent tunnel socket is useless; that test can never fail.
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Sessions don't need to use l2tp_sock_to_tunnel(xxx->tunnel_sock) for
accessing their parent tunnel. They have the .tunnel field in the
l2tp_session structure for that. Furthermore, in all these cases, the
session is registered, so we're guaranteed that .tunnel isn't NULL and
that the session properly holds a reference on the tunnel.
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This field has never been used.
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that IGMP packets no longer is flooded in HW, we want the SW bridge to
forward packets based on bridge configuration. To make that happen,
IGMP packets must have skb->offload_fwd_mark = 0.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After refcnt reaches zero, vlan_vid_del() could free
dev->vlan_info via RCU:
RCU_INIT_POINTER(dev->vlan_info, NULL);
call_rcu(&vlan_info->rcu, vlan_info_rcu_free);
However, the pointer 'grp' still points to that memory
since it is set before vlan_vid_del():
vlan_info = rtnl_dereference(dev->vlan_info);
if (!vlan_info)
goto out;
grp = &vlan_info->grp;
Depends on when that RCU callback is scheduled, we could
trigger a use-after-free in vlan_group_for_each_dev()
right following this vlan_vid_del().
Fix it by moving vlan_vid_del() before setting grp. This
is also symmetric to the vlan_vid_add() we call in
vlan_device_event().
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Fixes: efc73f4bbc23 ("net: Fix memory leak - vlan_info struct")
Cc: Alexander Duyck <alexander.duyck@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Girish Moodalbail <girish.moodalbail@oracle.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: Girish Moodalbail <girish.moodalbail@oracle.com>
Tested-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The software bridge needs to know if a packet has already been bridged
by hardware offload to ports in the same hardware offload, in order
that it does not re-flood them, causing duplicates. This is
particularly true for broadcast and multicast traffic which the host
has requested.
By setting offload_fwd_mark in the skb the bridge will only flood to
ports in other offloads and other netifs. Set this flag in the DSA and
EDSA tag driver.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
SWITCHDEV_ATTR_ID_PORT_PARENT_ID is used by the software bridge when
determining which ports to flood a packet out. If the packet
originated from a switch, it assumes the switch has already flooded
the packet out the switches ports, so the bridge should not flood the
packet itself out switch ports. Ports on the same switch are expected
to return the same parent ID when SWITCHDEV_ATTR_ID_PORT_PARENT_ID is
called.
DSA gets this wrong with clusters of switches. As far as the software
bridge is concerned, the cluster is all one switch. A packet from any
switch in the cluster can be assumed to have been flooded as needed
out of all ports of the cluster, not just the switch it originated
from. Hence all ports of a cluster should return the same parent. The
old implementation did not, each switch in the cluster had its own ID.
Also wrong was that the ID was not unique if multiple DSA instances
are in operation.
Use the tree ID as the parent ID, which is the same for all switches
in a cluster and unique across switch clusters.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The per-cpu counter for init_net is prepared in core_initcall.
The patch 7d720c3e ("percpu: add __percpu sparse annotations to net")
and d6d9ca0fe ("net: this_cpu_xxx conversions") optimize the
routines. Then remove the old counter.
Cc: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Tonghao Zhang <zhangtonghao@didichuxing.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 115106
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Sessions are already removed by the proto ->destroy() handlers, and
since commit f3c66d4e144a ("l2tp: prevent creation of sessions on terminated tunnels"),
we're guaranteed that no new session can be created afterwards.
Furthermore, l2tp_tunnel_closeall() can sleep when there are sessions
left to close. So we really shouldn't call it in a ->sk_destruct()
handler, as it can be used from atomic context.
Signed-off-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace the reordering distance measurement in packet unit with
sequence based approach. Previously it trackes the number of "packets"
toward the forward ACK (i.e. highest sacked sequence)in a state
variable "fackets_out".
Precisely measuring reordering degree on packet distance has not much
benefit, as the degree constantly changes by factors like path, load,
and congestion window. It is also complicated and prone to arcane bugs.
This patch replaces with sequence-based approach that's much simpler.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Soheil Hassas Yeganeh <soheil@google.com>
Reviewed-by: Priyaranjan Jha <priyarjha@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
FACK loss detection has been disabled by default and the
successor RACK subsumed FACK and can handle reordering better.
This patch removes FACK to simplify TCP loss recovery.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Soheil Hassas Yeganeh <soheil@google.com>
Reviewed-by: Priyaranjan Jha <priyarjha@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current code does not return after successfully preparing the VLAN
addition on every ports member of a it. Fix this.
Fixes: 1ca4aa9cd4cc ("net: dsa: check VLAN capability of every switch")
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current code does not return after successfully preparing the MDB
addition on every ports member of a multicast group. Fix this.
Fixes: a1a6b7ea7f2d ("net: dsa: add cross-chip multicast support")
Reported-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, the TIPC RPS dissector is based only on the incoming packets'
source node address, hence steering all traffic from a node to the same
core. We have seen that this makes the links vulnerable to starvation
and unnecessary resets when we turn down the link tolerance to very low
values.
To reduce the risk of this happening, we exempt probe and probe replies
packets from the convergence to one core per source node. Instead, we do
the opposite, - we try to diverge those packets across as many cores as
possible, by randomizing the flow selector key.
To make such packets identifiable to the dissector, we add a new
'is_keepalive' bit to word 0 of the LINK_PROTOCOL header. This bit is
set both for PROBE and PROBE_REPLY messages, and only for those.
It should be noted that these packets are not part of any flow anyway,
and only constitute a minuscule fraction of all packets sent across a
link. Hence, there is no risk that this will affect overall performance.
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a per-device sysctl to specify the default traffic class to use for
kernel originated IPv6 Neighbour Discovery packets.
Currently this includes:
- Router Solicitation (ICMPv6 type 133)
ndisc_send_rs() -> ndisc_send_skb() -> ip6_nd_hdr()
- Neighbour Solicitation (ICMPv6 type 135)
ndisc_send_ns() -> ndisc_send_skb() -> ip6_nd_hdr()
- Neighbour Advertisement (ICMPv6 type 136)
ndisc_send_na() -> ndisc_send_skb() -> ip6_nd_hdr()
- Redirect (ICMPv6 type 137)
ndisc_send_redirect() -> ndisc_send_skb() -> ip6_nd_hdr()
and if the kernel ever gets around to generating RA's,
it would presumably also include:
- Router Advertisement (ICMPv6 type 134)
(radvd daemon could pick up on the kernel setting and use it)
Interface drivers may examine the Traffic Class value and translate
the DiffServ Code Point into a link-layer appropriate traffic
prioritization scheme. An example of mapping IETF DSCP values to
IEEE 802.11 User Priority values can be found here:
https://tools.ietf.org/html/draft-ietf-tsvwg-ieee-802-11
The expected primary use case is to properly prioritize ND over wifi.
Testing:
jzem22:~# cat /proc/sys/net/ipv6/conf/eth0/ndisc_tclass
0
jzem22:~# echo -1 > /proc/sys/net/ipv6/conf/eth0/ndisc_tclass
-bash: echo: write error: Invalid argument
jzem22:~# echo 256 > /proc/sys/net/ipv6/conf/eth0/ndisc_tclass
-bash: echo: write error: Invalid argument
jzem22:~# echo 0 > /proc/sys/net/ipv6/conf/eth0/ndisc_tclass
jzem22:~# echo 255 > /proc/sys/net/ipv6/conf/eth0/ndisc_tclass
jzem22:~# cat /proc/sys/net/ipv6/conf/eth0/ndisc_tclass
255
jzem22:~# echo 34 > /proc/sys/net/ipv6/conf/eth0/ndisc_tclass
jzem22:~# cat /proc/sys/net/ipv6/conf/eth0/ndisc_tclass
34
jzem22:~# echo $[0xDC] > /proc/sys/net/ipv6/conf/eth0/ndisc_tclass
jzem22:~# tcpdump -v -i eth0 icmp6 and src host jzem22.pgc and dst host fe80::1
tcpdump: listening on eth0, link-type EN10MB (Ethernet), capture size 262144 bytes
IP6 (class 0xdc, hlim 255, next-header ICMPv6 (58) payload length: 24)
jzem22.pgc > fe80::1: [icmp6 sum ok] ICMP6, neighbor advertisement,
length 24, tgt is jzem22.pgc, Flags [solicited]
(based on original change written by Erik Kline, with minor changes)
v2: fix 'suspicious rcu_dereference_check() usage'
by explicitly grabbing the rcu_read_lock.
Cc: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: Erik Kline <ek@google.com>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Several response handlers return EBUSY if the data corresponding to the
command/response pair is already set. There is no reason to return an
error here; the channel is advertising something as enabled because we
told it to enable it, and it's possible that the feature has been
enabled previously.
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The NCSI driver is mostly silent which becomes a headache when trying to
determine what has occurred on the NCSI connection. This adds additional
logging in a few key areas such as state transitions and calling out
certain errors more visibly.
Signed-off-by: Samuel Mendoza-Jonas <sam@mendozajonas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes the cause of an WARNING indicatng TCP has pending
retransmission in Open state in tcp_fastretrans_alert().
The root cause is a bad interaction between path mtu probing,
if enabled, and the RACK loss detection. Upong receiving a SACK
above the sequence of the MTU probing packet, RACK could mark the
probe packet lost in tcp_fastretrans_alert(), prior to calling
tcp_simple_retransmit().
tcp_simple_retransmit() only enters Loss state if it newly marks
the probe packet lost. If the probe packet is already identified as
lost by RACK, the sender remains in Open state with some packets
marked lost and retransmitted. Then the next SACK would trigger
the warning. The likely scenario is that the probe packet was
lost due to its size or network congestion. The actual impact of
this warning is small by potentially entering fast recovery an
ACK later.
The simple fix is always entering recovery (Loss) state if some
packet is marked lost during path MTU probing.
Fixes: a0370b3f3f2c ("tcp: enable RACK loss detection to trigger recovery")
Reported-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Reported-by: Alexei Starovoitov <alexei.starovoitov@gmail.com>
Reported-by: Roman Gushchin <guro@fb.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a GSO skb of truesize O is segmented into 2 new skbs of truesize N1
and N2, we want to transfer socket ownership to the new fresh skbs.
In order to avoid expensive atomic operations on a cache line subject to
cache bouncing, we replace the sequence :
refcount_add(N1, &sk->sk_wmem_alloc);
refcount_add(N2, &sk->sk_wmem_alloc); // repeated by number of segments
refcount_sub(O, &sk->sk_wmem_alloc);
by a single
refcount_add(sum_of(N) - O, &sk->sk_wmem_alloc);
Problem is :
In some pathological cases, sum(N) - O might be a negative number, and
syzkaller bot was apparently able to trigger this trace [1]
atomic_t was ok with this construct, but we need to take care of the
negative delta with refcount_t
[1]
refcount_t: saturated; leaking memory.
------------[ cut here ]------------
WARNING: CPU: 0 PID: 8404 at lib/refcount.c:77 refcount_add_not_zero+0x198/0x200 lib/refcount.c:77
Kernel panic - not syncing: panic_on_warn set ...
CPU: 0 PID: 8404 Comm: syz-executor2 Not tainted 4.14.0-rc5-mm1+ #20
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:16 [inline]
dump_stack+0x194/0x257 lib/dump_stack.c:52
panic+0x1e4/0x41c kernel/panic.c:183
__warn+0x1c4/0x1e0 kernel/panic.c:546
report_bug+0x211/0x2d0 lib/bug.c:183
fixup_bug+0x40/0x90 arch/x86/kernel/traps.c:177
do_trap_no_signal arch/x86/kernel/traps.c:211 [inline]
do_trap+0x260/0x390 arch/x86/kernel/traps.c:260
do_error_trap+0x120/0x390 arch/x86/kernel/traps.c:297
do_invalid_op+0x1b/0x20 arch/x86/kernel/traps.c:310
invalid_op+0x18/0x20 arch/x86/entry/entry_64.S:905
RIP: 0010:refcount_add_not_zero+0x198/0x200 lib/refcount.c:77
RSP: 0018:ffff8801c606e3a0 EFLAGS: 00010282
RAX: 0000000000000026 RBX: 0000000000001401 RCX: 0000000000000000
RDX: 0000000000000026 RSI: ffffc900036fc000 RDI: ffffed0038c0dc68
RBP: ffff8801c606e430 R08: 0000000000000001 R09: 0000000000000000
R10: ffff8801d97f5eba R11: 0000000000000000 R12: ffff8801d5acf73c
R13: 1ffff10038c0dc75 R14: 00000000ffffffff R15: 00000000fffff72f
refcount_add+0x1b/0x60 lib/refcount.c:101
tcp_gso_segment+0x10d0/0x16b0 net/ipv4/tcp_offload.c:155
tcp4_gso_segment+0xd4/0x310 net/ipv4/tcp_offload.c:51
inet_gso_segment+0x60c/0x11c0 net/ipv4/af_inet.c:1271
skb_mac_gso_segment+0x33f/0x660 net/core/dev.c:2749
__skb_gso_segment+0x35f/0x7f0 net/core/dev.c:2821
skb_gso_segment include/linux/netdevice.h:3971 [inline]
validate_xmit_skb+0x4ba/0xb20 net/core/dev.c:3074
__dev_queue_xmit+0xe49/0x2070 net/core/dev.c:3497
dev_queue_xmit+0x17/0x20 net/core/dev.c:3538
neigh_hh_output include/net/neighbour.h:471 [inline]
neigh_output include/net/neighbour.h:479 [inline]
ip_finish_output2+0xece/0x1460 net/ipv4/ip_output.c:229
ip_finish_output+0x85e/0xd10 net/ipv4/ip_output.c:317
NF_HOOK_COND include/linux/netfilter.h:238 [inline]
ip_output+0x1cc/0x860 net/ipv4/ip_output.c:405
dst_output include/net/dst.h:459 [inline]
ip_local_out+0x95/0x160 net/ipv4/ip_output.c:124
ip_queue_xmit+0x8c6/0x18e0 net/ipv4/ip_output.c:504
tcp_transmit_skb+0x1ab7/0x3840 net/ipv4/tcp_output.c:1137
tcp_write_xmit+0x663/0x4de0 net/ipv4/tcp_output.c:2341
__tcp_push_pending_frames+0xa0/0x250 net/ipv4/tcp_output.c:2513
tcp_push_pending_frames include/net/tcp.h:1722 [inline]
tcp_data_snd_check net/ipv4/tcp_input.c:5050 [inline]
tcp_rcv_established+0x8c7/0x18a0 net/ipv4/tcp_input.c:5497
tcp_v4_do_rcv+0x2ab/0x7d0 net/ipv4/tcp_ipv4.c:1460
sk_backlog_rcv include/net/sock.h:909 [inline]
__release_sock+0x124/0x360 net/core/sock.c:2264
release_sock+0xa4/0x2a0 net/core/sock.c:2776
tcp_sendmsg+0x3a/0x50 net/ipv4/tcp.c:1462
inet_sendmsg+0x11f/0x5e0 net/ipv4/af_inet.c:763
sock_sendmsg_nosec net/socket.c:632 [inline]
sock_sendmsg+0xca/0x110 net/socket.c:642
___sys_sendmsg+0x31c/0x890 net/socket.c:2048
__sys_sendmmsg+0x1e6/0x5f0 net/socket.c:2138
Fixes: 14afee4b6092 ("net: convert sock.sk_wmem_alloc from atomic_t to refcount_t")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Using a spinlock in the VLAN action causes performance issues when the VLAN
action is used on multiple cores. Rewrote the VLAN action to use RCU read
locking for reads and updates instead.
All functions now use an RCU dereferenced pointer to access the VLAN action
context. Modified helper functions used by other modules, to use the RCU as
opposed to directly accessing the structure.
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Manish Kurup <manish.kurup@verizon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The VLAN action maintains one set of stats across all cores, and uses a
spinlock to synchronize updates to it from the same. Changed this to use a
per-CPU stats context instead.
This change will result in better performance.
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Manish Kurup <manish.kurup@verizon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
rds_ib_recv_refill() is a function that refills an IB receive
queue. It can be called from both the CQE handler (tasklet) and a
worker thread.
Just after the call to ib_post_recv(), a debug message is printed with
rdsdebug():
ret = ib_post_recv(ic->i_cm_id->qp, &recv->r_wr, &failed_wr);
rdsdebug("recv %p ibinc %p page %p addr %lu ret %d\n", recv,
recv->r_ibinc, sg_page(&recv->r_frag->f_sg),
(long) ib_sg_dma_address(
ic->i_cm_id->device,
&recv->r_frag->f_sg),
ret);
Now consider an invocation of rds_ib_recv_refill() from the worker
thread, which is preemptible. Further, assume that the worker thread
is preempted between the ib_post_recv() and rdsdebug() statements.
Then, if the preemption is due to a receive CQE event, the
rds_ib_recv_cqe_handler() will be invoked. This function processes
receive completions, including freeing up data structures, such as the
recv->r_frag.
In this scenario, rds_ib_recv_cqe_handler() will process the receive
WR posted above. That implies, that the recv->r_frag has been freed
before the above rdsdebug() statement has been executed. When it is
later executed, we will have a NULL pointer dereference:
[ 4088.068008] BUG: unable to handle kernel NULL pointer dereference at 0000000000000020
[ 4088.076754] IP: rds_ib_recv_refill+0x87/0x620 [rds_rdma]
[ 4088.082686] PGD 0 P4D 0
[ 4088.085515] Oops: 0000 [#1] SMP
[ 4088.089015] Modules linked in: rds_rdma(OE) rds(OE) rpcsec_gss_krb5(E) nfsv4(E) dns_resolver(E) nfs(E) fscache(E) mlx4_ib(E) ib_ipoib(E) rdma_ucm(E) ib_ucm(E) ib_uverbs(E) ib_umad(E) rdma_cm(E) ib_cm(E) iw_cm(E) ib_core(E) binfmt_misc(E) sb_edac(E) intel_powerclamp(E) coretemp(E) kvm_intel(E) kvm(E) irqbypass(E) crct10dif_pclmul(E) crc32_pclmul(E) ghash_clmulni_intel(E) pcbc(E) aesni_intel(E) crypto_simd(E) iTCO_wdt(E) glue_helper(E) iTCO_vendor_support(E) sg(E) cryptd(E) pcspkr(E) ipmi_si(E) ipmi_devintf(E) ipmi_msghandler(E) shpchp(E) ioatdma(E) i2c_i801(E) wmi(E) lpc_ich(E) mei_me(E) mei(E) mfd_core(E) nfsd(E) auth_rpcgss(E) nfs_acl(E) lockd(E) grace(E) sunrpc(E) ip_tables(E) ext4(E) mbcache(E) jbd2(E) fscrypto(E) mgag200(E) i2c_algo_bit(E) drm_kms_helper(E) syscopyarea(E) sysfillrect(E) sysimgblt(E)
[ 4088.168486] fb_sys_fops(E) ahci(E) ixgbe(E) libahci(E) ttm(E) mdio(E) ptp(E) pps_core(E) drm(E) sd_mod(E) libata(E) crc32c_intel(E) mlx4_core(E) i2c_core(E) dca(E) megaraid_sas(E) dm_mirror(E) dm_region_hash(E) dm_log(E) dm_mod(E) [last unloaded: rds]
[ 4088.193442] CPU: 20 PID: 1244 Comm: kworker/20:2 Tainted: G OE 4.14.0-rc7.master.20171105.ol7.x86_64 #1
[ 4088.205097] Hardware name: Oracle Corporation ORACLE SERVER X5-2L/ASM,MOBO TRAY,2U, BIOS 31110000 03/03/2017
[ 4088.216074] Workqueue: ib_cm cm_work_handler [ib_cm]
[ 4088.221614] task: ffff885fa11d0000 task.stack: ffffc9000e598000
[ 4088.228224] RIP: 0010:rds_ib_recv_refill+0x87/0x620 [rds_rdma]
[ 4088.234736] RSP: 0018:ffffc9000e59bb68 EFLAGS: 00010286
[ 4088.240568] RAX: 0000000000000000 RBX: ffffc9002115d050 RCX: ffffc9002115d050
[ 4088.248535] RDX: ffffffffa0521380 RSI: ffffffffa0522158 RDI: ffffffffa0525580
[ 4088.256498] RBP: ffffc9000e59bbf8 R08: 0000000000000005 R09: 0000000000000000
[ 4088.264465] R10: 0000000000000339 R11: 0000000000000001 R12: 0000000000000000
[ 4088.272433] R13: ffff885f8c9d8000 R14: ffffffff81a0a060 R15: ffff884676268000
[ 4088.280397] FS: 0000000000000000(0000) GS:ffff885fbec80000(0000) knlGS:0000000000000000
[ 4088.289434] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 4088.295846] CR2: 0000000000000020 CR3: 0000000001e09005 CR4: 00000000001606e0
[ 4088.303816] Call Trace:
[ 4088.306557] rds_ib_cm_connect_complete+0xe0/0x220 [rds_rdma]
[ 4088.312982] ? __dynamic_pr_debug+0x8c/0xb0
[ 4088.317664] ? __queue_work+0x142/0x3c0
[ 4088.321944] rds_rdma_cm_event_handler+0x19e/0x250 [rds_rdma]
[ 4088.328370] cma_ib_handler+0xcd/0x280 [rdma_cm]
[ 4088.333522] cm_process_work+0x25/0x120 [ib_cm]
[ 4088.338580] cm_work_handler+0xd6b/0x17aa [ib_cm]
[ 4088.343832] process_one_work+0x149/0x360
[ 4088.348307] worker_thread+0x4d/0x3e0
[ 4088.352397] kthread+0x109/0x140
[ 4088.355996] ? rescuer_thread+0x380/0x380
[ 4088.360467] ? kthread_park+0x60/0x60
[ 4088.364563] ret_from_fork+0x25/0x30
[ 4088.368548] Code: 48 89 45 90 48 89 45 98 eb 4d 0f 1f 44 00 00 48 8b 43 08 48 89 d9 48 c7 c2 80 13 52 a0 48 c7 c6 58 21 52 a0 48 c7 c7 80 55 52 a0 <4c> 8b 48 20 44 89 64 24 08 48 8b 40 30 49 83 e1 fc 48 89 04 24
[ 4088.389612] RIP: rds_ib_recv_refill+0x87/0x620 [rds_rdma] RSP: ffffc9000e59bb68
[ 4088.397772] CR2: 0000000000000020
[ 4088.401505] ---[ end trace fe922e6ccf004431 ]---
This bug was provoked by compiling rds out-of-tree with
EXTRA_CFLAGS="-DRDS_DEBUG -DDEBUG" and inserting an artificial delay
between the rdsdebug() and ib_ib_port_recv() statements:
/* XXX when can this fail? */
ret = ib_post_recv(ic->i_cm_id->qp, &recv->r_wr, &failed_wr);
+ if (can_wait)
+ usleep_range(1000, 5000);
rdsdebug("recv %p ibinc %p page %p addr %lu ret %d\n", recv,
recv->r_ibinc, sg_page(&recv->r_frag->f_sg),
(long) ib_sg_dma_address(
The fix is simply to move the rdsdebug() statement up before the
ib_post_recv() and remove the printing of ret, which is taken care of
anyway by the non-debug code.
Signed-off-by: Håkon Bugge <haakon.bugge@oracle.com>
Reviewed-by: Knut Omang <knut.omang@oracle.com>
Reviewed-by: Wei Lin Guay <wei.lin.guay@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As patch 'ip_gre: add the support for i/o_flags update via netlink'
did for netlink, we also need to do the same job for these update
via ioctl.
This patch is to update i/o_flags and call ipgre_link_update to
recalculate these gre properties after ip_tunnel_ioctl does the
common update.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now ip_gre is using ip_tunnel_changelink to update it's properties, but
ip_tunnel_changelink in ip_tunnel doesn't update i/o_flags as a common
function.
o_flags updates would cause that tunnel->tun_hlen / hlen and dev->mtu /
needed_headroom need to be recalculated, and dev->(hw_)features need to
be updated as well.
Therefore, we can't just add the update into ip_tunnel_update called
in ip_tunnel_changelink, and it's also better not to touch ip_tunnel
codes.
This patch updates i/o_flags and calls ipgre_link_update to recalculate
these gre properties after ip_tunnel_changelink does the common update.
Note that since ipgre_link_update doesn't know the lower dev, it will
update gre->hlen, dev->mtu and dev->needed_headroom with the value of
'new tun_hlen - old tun_hlen'. In this way, we can avoid many redundant
codes, unlike ip6_gre.
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: William Tu <u9012063@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Note that when a new netns is created, it inherits its
sysctl_tcp_rmem and sysctl_tcp_wmem from initial netns.
This change is needed so that we can refine TCP rcvbuf autotuning,
to take RTT into consideration.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Wei Wang <weiwan@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As we want to gradually implement per netns sysctl_rmem and sysctl_wmem
on per protocol basis, add two new fields in struct proto,
and two new helpers : sk_get_wmem0() and sk_get_rmem0()
First user will be TCP. Then UDP and SCTP can be easily converted,
while DECNET probably wont get this support.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
