| Age | Commit message (Collapse) | Author |
|---|
|
Unlike BR/EDR, for LE when we're in the BT_CONNECT state we may or may
not have already have sent the Connect Request. This means that we need
some extra tracking of the request. This patch adds an extra channel
flag to prevent the request from being sent a second time.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
When receiving fragments over an LE Connection oriented Channel they
need to be collected up and eventually merged into a single SDU. This
patch adds the necessary code for collecting up the fragment skbs to the
channel context and passing them to the recv() callback when the entire
SDU has been received.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This patch adds segmentation support for outgoing data packets. Packets
are segmented based on the MTU and MPS values. The l2cap_chan struct
already contains many helpful variables from BR/EDR Enhanced L2CAP which
can be used for this.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Setting the BT_SK_SUSPEND socket flag from the L2CAP core is causing a
dependency on the socket. So instead of doing that, use a channel
callback into the socket handling to suspend.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Since LE CoC support needs to be enabled through a module option for now
we need to reject any related signaling PDUs in addition to rejecting
the creation of LE CoC sockets (which we already do).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This patch adds the necessary discipline for reacting to LE L2CAP
Credits packets, sending those packets, and modifying the known credits
accordingly.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
We should return credits to the remote side whenever they fall below a
certain level (in our case under half of the initially given amount).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This patch adds new socket options for LE sockets since the existing
L2CAP_OPTIONS socket option is not usable for LE. For now, the new
socket options also require LE CoC support to be explicitly enabled to
leave some playroom in case something needs to be changed in a backwards
incompatible way.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Most of the values in L2CAP_OPTIONS are not applicable for LE and those
that are have different semantics. It makes therefore sense to
completely block this socket option for LE and add (in a separate patch)
a new socket option for tweaking the values that do make sense (mainly
the send and receive MTU). Legacy user space ATT code still depends on
getsockopt for L2CAP_OPTIONS though so we need to plug a hole for that
for backwards compatibility.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This patch adds tracking of L2CAP connection oriented channel local and
remote credits to struct l2cap_chan and ensures that connect requests
and responses contain the right values.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The LE connection oriented channels have their own mode with its own
data transfer rules. In order to implement this properly we need to
distinguish L2CAP channels operating in this mode from other modes.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This patch makes the error handling and return logic of l2cap_le_sig_cmd
consistent with its BR/EDR counterpart.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The normal L2CAP Disconnect request and response are also used for LE
connection oriented channels. Therefore, we can simply use the existing
handler functions for terminating LE based L2CAP channels.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Sending of the L2CAP Disconnect request should also be performed for LE
based channels. The proper thing to do is therefore to look at whether
there's a PSM specified for the channel instead of looking at the link
type.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This patch adds the necessary boiler plate code to handle receiving
L2CAP connect requests over LE and respond to them with a proper connect
response.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
We'll need to have a separate code path for LE based connection
rejection so it's cleaner to move out the response construction code
into its own function (and later a second one for LE).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This function is needed both by the smp_conn_security function as well
as upcoming code to check for the security requirements when receiving
an L2CAP connect request over LE.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This patch adds the necessary code to send an LE L2CAP Connect Request
and handle its response when user space has provided us with an LE
socket with a PSM instead of a fixed CID.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Once connection oriented L2CAP channels over LE are supported they will
need a completely separate handling from BR/EDR channels.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The LE signaling PDU length is already calculated in the
l2cap_le_sig_channel function so we can just pass the value to the
various handler functions to avoid unnecessary recalculations (byte
order conversions). Right now the only user is the connection parameter
update procedure, but as new LE signaling operations become available
(for connection oriented channels) they will also be able to make use of
the value.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
With connection oriented L2CAP channels some code paths will be shared
with BR/EDR links. It is therefore necessary to allow the
l2cap_chan_check_security function to be usable also for LE links in
addition to BR/EDR ones. This means that smp_conn_security() needs to be
called instead of hci_conn_security() in the case of an LE link.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Once connection oriented L2CAP channels become possible for LE we need
to be able to specify the link type we're interested in when looking up
L2CAP channels. Therefore, add a link_type parameter to the
l2cap_global_chan_by_psm() function which gets compared to the address
type associated with each l2cap_chan.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Along with the L2CAP Connection Oriented Channels features it is now
allowed to use both custom fixed CIDs as well as PSM based (connection
oriented connections). Since the support for this (with the subsequent
patches) is still on an experimental stage, add a module parameter to
enable it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This patch is just a trivial coding style fix to remove unnecessary
braces from a one-line if-statement.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The AES cipher is used in ECB mode by SMP and therefore doesn't use an
IV (crypto_blkcipher_ivsize returns 0) so the code trying to set the IV
was never getting called. Simply remove this code to avoid anyone from
thinking it actually makes some difference.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This function was always just making a single get_random_bytes() call
and always returning the value 0. It's simpler to just call
get_random_bytes() directly where needed.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
hci_disconn_complete_evt() logic is more complicated than what it
should be, making it hard to follow and add new features.
So this patch does some code refactoring by handling the error cases
in the beginning of the function and by moving the main flow into the
first level of function scope. No change is done in the event handling
logic itself.
Besides organizing this messy code, this patch makes easier to add
code for handling LE auto connection (which will be added in a further
patch).
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
According to b644ba336 (patch that introduced HCI_CONN_MGMT_CONNECTED
flag), the HCI_CONN_MGMT_CONNECTED flag tracks when mgmt has been
notified about the connection.
That being said, there is no point in calling mgmt_disconnect_failed()
conditionally based on this flag. mgmt_disconnect_failed() removes
pending MGMT_OP_DISCONNECT commands, it doesn't matter if that
connection was notified or not.
Moreover, if the Disconnection Complete event has status then we have
nothing else to do but call mgmt_disconnect_failed() and return.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
The send parameter has only been used for determining whether to send a
Pairing Failed PDU or not. However, the function can equally well use
the already existing reason parameter to make this choice and send the
PDU whenever a non-zero value was passed.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
We can safely remove the link type check from hci_disconn_complete_
evt() since this check in not required for mgmt_disconnect_failed()
and mgmt_device_disconnected() does it internally.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This patch adds an extra check in mgmt_device_disconnected() so we only
send the "Device Disconnected" event if it is ACL_LINK or LE_LINK link
type.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Check the address and address type in mgmt_disconnect_failed() otherwise
we may wrongly fail the MGMT_OP_DISCONNECT command.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The list of supported commands of a controller can not change during
its lifetime. So store the list just once during the setup procedure
and not every time the HCI command is executed.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
The complete list of local features are available through debugfs and
so there is no need to add a debug print here.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
The default own address type is currently set at every power on of
a controller. This overwrites the value set via debugfs. To avoid
this issue, set the default own address type only during controller
setup.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
There is an old Panasonic module with a Zeevo chip in there that is
not really operating according to Bluetooth core specification when
it comes to setting the IAC LAP for limited discoverable mode.
For reference, this is the vendor information about this module:
< HCI Command: Read Local Version Information (0x04|0x0001) plen 0
> HCI Event: Command Complete (0x0e) plen 12
Read Local Version Information (0x04|0x0001) ncmd 1
Status: Success (0x00)
HCI version: Bluetooth 1.2 (0x02) - Revision 196 (0x00c4)
LMP version: Bluetooth 1.2 (0x02) - Subversion 61 (0x003d)
Manufacturer: Zeevo, Inc. (18)
The module reports only the support for one IAC at a time. And that
is totally acceptable according to the Bluetooth core specification
since the minimum supported IAC is only one.
< HCI Command: Read Number of Supported IAC (0x03|0x0038) plen 0
> HCI Event: Command Complete (0x0e) plen 5
Read Number of Supported IAC (0x03|0x0038) ncmd 1
Status: Success (0x00)
Number of IAC: 1
The problem arises when trying to program two IAC into the module
on a controller that only supports one.
< HCI Command: Write Current IAC LAP (0x03|0x003a) plen 7
Number of IAC: 2
Access code: 0x9e8b00 (Limited Inquiry)
Access code: 0x9e8b33 (General Inquiry)
> HCI Event: Command Status (0x0f) plen 4
Write Current IAC LAP (0x03|0x003a) ncmd 1
Status: Unknown HCI Command (0x01)
While this looks strange, but according to the Bluetooth core
specification it is a legal operation. The controller has to
ignore the other values and only program as many as it supports.
This command shall clear any existing IACs and stores Num_Current_IAC
and the IAC_LAPs in to the controller. If Num_Current_IAC is greater
than Num_Support_IAC then only the first Num_Support_IAC shall be
stored in the controller, and a Command Complete event with error
code Success (0x00) shall be generated.
This specific controller has a bug here and just returns an error. So
in case the number of supported IAC is less than two and the limited
discoverable mode is requested, now only the LIAC is written to
the controller.
< HCI Command: Write Current IAC LAP (0x03|0x003a) plen 4
Number of IAC: 1
Access code: 0x9e8b00 (Limited Inquiry)
> HCI Event: Command Complete (0x0e) plen 4
Write Current IAC LAP (0x03|0x003a) ncmd 1
Status: Success (0x00)
All other controllers that only support one IAC seem to handle this
perfectly fine, but this fix will only write the LIAC for these
controllers as well.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
|
|
Drivers with hardware rate control were given
sta->rx_nss set to 0. This was because rx_nss
calculation procedure was protected by hw/sw rate
control check.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The current channel switch code has a potential deadlock:
1) * cfg80211_stop_ap acquires wdev-lock
* ieee80211_stop_ap calls cancel_work_sync for the csa_finalize_work,
which acquires the associated worker-lock
2) * ieee80211_csa_finalize_work holds the worker-lock when run
* it calls cfg80211_ch_switch_notify which will claim the wdev-lock,
and also needs to claim the sdata-lock (which is the same as the
wdev-lock) to modify the beacons.
It is sufficient to just set the channel switch active to false. If the
worker is running later, it will find the channel switch to not be
active anymore and returns immediately without changing anything.
Canceling the worker is done anyway when the interface goes down
(ieee80211_do_stop).
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The channel switch notification should be sent under the
wdev/sdata-lock, preferably in the same moment as the channel change
happens, to avoid races by other callers (e.g. start/stop_ap).
This also adds the previously missing sdata_lock protection in
csa_finalize_work.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The csa finalize worker needs to change the beacon information (for
different modes). These are normally protected under rtnl lock, but the
csa finalize worker is called by drivers and should not acquire the RTNL
lock. Therefore change access protection for beacons to sdata/wdev lock.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
[fix sdata_dereference]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
To avoid race conditions in functions which modify the beacon
information, lock these using the wdev lock. This is especially required
to avoid problems for csa handling functions which modify beacons but
can not be called under rtnl lock.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The local TSF timer is used to compute the timing offset between
mesh peers on beacon reception. However, asking the device for
the TSF is not very accurate, so we prefer to use rx->mactime
if available. In the latter case, calling drv_get_tsf() just
adds more delay into the RX path, so skip it if we can.
Signed-off-by: Bob Copeland <bob@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Change cfg80211 and mac80211 to use cfg80211_mgmt_tx_params
struct to aggregate parameters for mgmt_tx functions.
This makes the functions' signatures less clumsy and allows
less painful parameters extension.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
[fix all other drivers]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
There's a bug in tracking HT opmode changes in mac80211, it
fails to update the driver when the channel parameters don't
change.
Move the code to do the HT opmode checking independently of
the channel/bandwidth tracking.
Signed-off-by: Avri Altman <avri.altman@intel.com>
[edit commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
All interface types now properly clean up their stations
using some form of sta_info_flush() themselves, so there's
no need to try it again at teardown. Remove the call to
get rid of the extra delay from the synchronize_net() and
rcu_barrier() calls.
Reported-by: Moshe Benji <moshe.benji@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Measure TX latency and jitter statistics per station per TID.
These Measurements are disabled by default and can be enabled
via debugfs.
Features included for each station's TID:
1. Keep count of the maximum and average latency of Tx frames.
2. Keep track of many frames arrived in a specific time range
(need to enable through debugfs and configure the bins ranges)
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
nla_put_flag needs a real nl80211 attribute id, not a wiphy flag bit.
While at it, split 5 and 10 MHz capability flags in case we ever need
to support hardware that can only do one of the two.
Also move the flag settings to the split-only information so we don't
increase the space needed for old userspace.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
[change location of flag setting]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
ATM minstrel_ht does not check whether a sampling rate is supported.
Unsupported rates attempts can trigger when there are holes in bitfields
of supported MCSes belonging to the same group (e.g many devices are
MCS32 capable without MCS33->39 capable, also we systematically have a
hole for CCK rates).
Drop any attempts to sample unsupported rates, as suggested by Felix.
This is not a problem in minstrel which fills a per STA sample table
with only supported rates (though only at init).
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
