summaryrefslogtreecommitdiff
path: root/net
AgeCommit message (Collapse)Author
2013-02-04cfg80211: refactor hidden SSID findingJohannes Berg
Instead of duplicating the rbtree functions, pass an argument to the compare function. This removes the code duplication for the two searches. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-02-04cfg80211: expand per-station byte counters to 64bitVladimir Kondratiev
In per-station statistics, present 32bit counters are too small for practical purposes - with gigabit speeds, it get overlapped every few seconds. Expand counters in the struct station_info to be 64-bit. Driver can still fill only 32-bit and indicate in @filled only bits like STATION_INFO_[TR]X_BYTES; in case driver provides full 64-bit counter, it should also set in @filled bit STATION_INFO_[TR]RX_BYTES64 Netlink sends both 32-bit and 64-bit counters, if present, to not break userspace. Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com> [change to also have 32-bit counters if driver advertises 64-bit] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-02-04mac80211: always allow calling ieee80211_connection_loss()Johannes Berg
With multi-channel, there's a corner case where a driver doesn't receive a beacon soon enough to be able to sync its timers with the AP. In this case, the only recovery (after trying again) is to disconnect from the AP. Allow calling ieee80211_connection_loss() for such cases. To make that possible, modify the work function to not rely on the IEEE80211_HW_CONNECTION_MONITOR flag but use new state kept in the interface instead. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-02-04mac80211: send deauth when connection is lostJohannes Berg
If the driver determines the connection is lost, send a deauth frame to the AP anyway just in case it still considers the connection alive. The frame might not go through, but at least we've tried. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-01-31mac80211: improve latency and throughput while software scanningStanislaw Gruszka
Patch vastly improve latency while scanning. Slight throughput improvements were observed as well. Is intended for improve performance of voice and video applications, when scan is periodically requested by user space (i.e. default NetworkManager behaviour). Patch remove latency requirement based on PM_QOS_NETWORK_LATENCY, this value is 2000 seconds by default (i.e. approximately 0.5 hour !?!). Also remove listen interval requirement, which based on beaconing and depending on BSS parameters. It can make we stay off-channel for a second or more. Instead try to offer the best latency that we could, i.e. be off-channel no longer than PASSIVE channel scan time: 125 ms. That mean we will scan two ACTIVE channels and go back to on-channel, and one PASSIVE channel, and go back to on-channel. Patch also decrease PASSIVE channel scan time to about 110 ms. As drawback patch increase overall scan time. On my tests, when scanning both 2GHz and 5GHz bands, scanning time increase from 5 seconds up to 10 seconds. Since that increase happen only when we are associated, I think it can be acceptable. If eventually better scan time is needed for situations when we lose signal and quickly need to decide to which AP roam, additional scan flag or parameter can be introduced. I tested patch by doing: while true; do iw dev wlan0 scan; sleep 3; done > /dev/null and ping -i0.2 -c 1000 HOST on remote and local machine, results are as below: * Ping from local periodically scanning machine to AP: Unpatched: rtt min/avg/max/mdev = 0.928/24.946/182.135/36.873 ms Patched: rtt min/avg/max/mdev = 0.928/19.678/150.845/33.130 ms * Ping from remote machine to periodically scanning machine: Unpatched: rtt min/avg/max/mdev = 1.637/120.683/709.139/164.337 ms Patched: rtt min/avg/max/mdev = 1.807/26.893/201.435/40.284 ms Throughput measured by scp show following results. * Upload to periodically scanning machine: Unpatched: 3.9MB/s 03:15 Patched: 4.3MB/s 02:58 * Download from periodically scanning machine: Unpatched: 5.5MB/s 02:17 Patched: 6.2MB/s 02:02 Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-01-31mac80211: start auth/assoc timeout on frame statusJohannes Berg
When sending authentication/association frames they might take a bit of time to go out because we may have to synchronise with the AP, in particular in the case where it's really a P2P GO. In this case the 200ms fixed timeout could potentially be too short if the beacon interval is relatively large. For drivers that report TX status we can do better. Instead of starting the timeout directly, start it only when the frame status arrives. Since then the frame was out on the air, we can wait shorter (the typical response time is supposed to be 30ms, wait 100ms.) Also, if the frame failed to be transmitted try again right away instead of waiting. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-01-31cfg80211: remove free_priv BSS APIJohannes Berg
Now that mac80211 no longer uses this API, remove it completely. If anyone needs it again, we can revert this patch of course, but mac80211 was the only user right now. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-01-31mac80211: remove unused mesh data from bssJohannes Berg
These pointers/values are never used, remove them. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-01-31mac80211: remove last_probe_resp from bssJohannes Berg
We track this, but never use it, so we can just remove it. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-01-31mac80211: inform the driver about update of dtim_periodEmmanuel Grumbach
Currently, when the driver requires the DTIM period, mac80211 will wait to hear a beacon before association. This behavior is suboptimal since some drivers may be able to deal with knowing the DTIM period after the association, if they get it at all. To address this, notify the drivers with bss_info_changed with the new BSS_CHANGED_DTIM_PERIOD flag when the DTIM becomes known. This might be when changing to associated, or later when the entire association was done with only probe response information. Rename the hardware flag for the current behaviour to IEEE80211_HW_NEED_DTIM_BEFORE_ASSOC to more accurately reflect its behaviour. IEEE80211_HW_NEED_DTIM_PERIOD is no longer accurate as all drivers get the DTIM period now, just not before association. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-01-31mac80211: remove assoc data "sent_assoc"Johannes Berg
The field is never used, so remove it. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-01-31cfg80211/mac80211: support reporting wakeup reasonJohannes Berg
When waking up from WoWLAN, it is useful to know what triggered the wakeup. Support reporting the wakeup reason(s) in cfg80211 (and a pass-through in mac80211) to allow userspace to know. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-01-29mac80211: dynamic short slot time for MBSSsThomas Pedersen
The standard mandates mesh STAs to set the ERP Short Slot Time capability info bit in beacons to 0. Even though this is their way of disallowing short slot time for mesh STAs, there should be no harm in enabling it if we determine all STAs in the current MBSS support ERP rates. Increases throughput about 20% for legacy rates when enabled. Signed-off-by: Thomas Pedersen <thomas@cozybit.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-01-29cfg80211: add SME state to warning in __cfg80211_mlme_disassocJohannes Berg
The warning here occasionally triggers but we haven't found the cause yet. It's a valid warning since if it triggers the SME state got confused, so add the SME state to it to help narrow it down in the future. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-01-29mac80211: remove IEEE80211_HW_TEARDOWN_AGGR_ON_BAR_FAILStanislaw Gruszka
This is basically a revert of: commit 5b632fe85ec82e5c43740b52e74c66df50a37db3 Author: Stanislaw Gruszka <sgruszka@redhat.com> Date: Mon Dec 3 12:56:33 2012 +0100 mac80211: introduce IEEE80211_HW_TEARDOWN_AGGR_ON_BAR_FAIL We do not need this flag any longer, rt2x00 BAR/BA problem was fixed correctly by wireless-testing commit: commit 84e9e8ebd369679a958200a8baca96aafb2393bb Author: Helmut Schaa <helmut.schaa@googlemail.com> Date: Thu Jan 17 17:34:32 2013 +0100 rt2x00: Improve TX status handling for BlockAckReq frames Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-01-29Merge remote-tracking branch 'wireless-next/master' into HEADJohannes Berg
2013-01-28Merge branch 'master' of ↵John W. Linville
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless Conflicts: drivers/net/wireless/ath/ath9k/main.c drivers/net/wireless/iwlwifi/dvm/tx.c
2013-01-28mac80211: fix mesh_sta_info_get() reshuffle damageThomas Pedersen
Before "mac80211: clean up mesh sta allocation warning" was applied, mesh_sta_info_get() was reshuffled to please sparse. As a result we neglect to initialize newly created STAs. Fix this. Signed-off-by: Thomas Pedersen <thomas@cozybit.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-01-25cfg80211/nl80211: add API for MAC address ACLsVasanthakumar Thiagarajan
Add API to enable drivers to implement MAC address based access control in AP/P2P GO mode. Capable drivers advertise this capability by setting the maximum number of MAC addresses in such a list in wiphy->max_acl_mac_addrs. An initial ACL may be given to the NL80211_CMD_START_AP command and/or changed later with NL80211_CMD_SET_MAC_ACL. Black- and whitelists are supported, but not simultaneously. Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com> [rewrite commit log, many cleanups] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-01-25mac80211: avoid a build warningArnd Bergmann
gcc cannot prove that the value of sdata->vif.type does not change between the switch() statement and the second comparison to NL80211_IFTYPE_AP, causing a harmless warning. Slightly reordering the code makes the warning go away with no functional change. Without this patch, building ARM at91sam9g45_defconfig with gcc-4.6 results in: net/mac80211/tx.c: In function 'ieee80211_subif_start_xmit': net/mac80211/tx.c:1797:22: warning: 'chanctx_conf' may be used uninitialized in this function [-Wuninitialized] Signed-off-by: Arnd Bergmann <arnd@arndb.de> Cc: Johannes Berg <johannes@sipsolutions.net> Cc: "John W. Linville" <linville@tuxdriver.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: linux-wireless@vger.kernel.org Cc: netdev@vger.kernel.org Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-01-24mac80211: remove redundant checkJohannes Berg
There's no need to have two checks for "associated" in ieee80211_sta_restart(), make the first one locked to not race (unlikely at this point during resume) and remove the second check. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-01-24cfg80211: fix channel check in cfg80211_can_use_iftype_chanSimon Wunderlich
In commit "cfg80211: check radar interface combinations" a regression was introduced which might lead to NULL dereference if the argument chan = NULL, which might happen in IBSS/wext case (and probably others). Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-01-24mac80211: support mesh rate updatesThomas Pedersen
An existing mesh station entry may change its rate capabilities, so call rate_control_rate_update() to notify the rate control. Signed-off-by: Thomas Pedersen <thomas@cozybit.com> [fix compilation] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-01-24mac80211: clean up mesh sta allocation warningThomas Pedersen
This refactoring fixes a "scheduling while atomic" warning when allocating a mesh station entry while holding the RCU read lock. Fix this by creating a new function mesh_sta_info_get(), which correctly handles the locking and returns under RCU. Also move some unnecessarily #ifdefed mesh station init code from sta_info_alloc() to __mesh_sta_info_alloc(). Signed-off-by: Thomas Pedersen <thomas@cozybit.com> [change code flow to make sparse happy] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-01-24mac80211: fix aggregation state with current driversJohannes Berg
For drivers that don't actually flush their queues when aggregation stop with the IEEE80211_AMPDU_TX_STOP_FLUSH or IEEE80211_AMPDU_TX_STOP_FLUSH_CONT reasons is done, like iwlwifi or iwlegacy, mac80211 can then transmit on a TID that the driver still considers busy. This happens in the following way: - IEEE80211_AMPDU_TX_STOP_FLUSH requested - driver marks TID as emptying - mac80211 removes tid_tx data, this can copy packets to the TX pending queues and also let new packets through to the driver - driver gets unexpected TX as it wasn't completely converted to the new API In iwlwifi, this lead to the following warning: WARNING: at drivers/net/wireless/iwlwifi/dvm/tx.c:442 iwlagn_tx_skb+0xc47/0xce0 Tx while agg.state = 4 Modules linked in: [...] Pid: 0, comm: kworker/0:0 Tainted: G W 3.1.0 #1 Call Trace: [<c1046e42>] warn_slowpath_common+0x72/0xa0 [<c1046f13>] warn_slowpath_fmt+0x33/0x40 [<fddffa17>] iwlagn_tx_skb+0xc47/0xce0 [iwldvm] [<fddfcaa3>] iwlagn_mac_tx+0x23/0x40 [iwldvm] [<fd8c98b6>] __ieee80211_tx+0xf6/0x3c0 [mac80211] [<fd8cbe00>] ieee80211_tx+0xd0/0x100 [mac80211] [<fd8cc176>] ieee80211_xmit+0x96/0xe0 [mac80211] [<fd8cc578>] ieee80211_subif_start_xmit+0x348/0xc80 [mac80211] [<c1445207>] dev_hard_start_xmit+0x337/0x6d0 [<c145eee9>] sch_direct_xmit+0xa9/0x210 [<c14462c0>] dev_queue_xmit+0x1b0/0x8e0 Fortunately, solving this problem is easy as the station is being destroyed, so such transmit packets can only happen due to races. Instead of trying to close the race just let the race not reach the drivers by making two changes: 1) remove the explicit aggregation session teardown in the managed mode code, the same thing will be done when the station is removed, in __sta_info_destroy. 2) When aggregation stop with AGG_STOP_DESTROY_STA is requested, leave the tid_tx data around as stopped. It will be cleared and freed in cleanup_single_sta later, but until then any racy packets will be put onto the tid_tx pending queue instead of transmitted which is fine since the station is being removed. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-01-24mac80211: provide the vif in rssi_callbackEmmanuel Grumbach
Since drivers can support several BSS / P2P Client interfaces, the rssi callback needs to inform the driver about the interface teh rssi event relates to. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-01-22Merge branch 'for-john' of ↵John W. Linville
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
2013-01-22Merge branch 'for-john' of ↵John W. Linville
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
2013-01-18mac80211: allow drivers to access IPv6 informationJohannes Berg
To be able to implement NS response offloading (in regular operation or while in WoWLAN) drivers need to know the IPv6 addresses assigned to interfaces. Implement an IPv6 notifier in mac80211 to call the driver when addresses change. Unlike for IPv4, implement it as a callback rather than as a list in the BSS configuration, that is more flexible. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-01-18mac80211: improve aggregation debug messagesJohannes Berg
A lot of the aggregation messages don't indicate the station so they're hard to understand if there are multiple sessions in progress. Make that easier by adding the MAC address to most messages. Also add the TID if it wasn't already there. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-01-18mac80211: remove ARP filter enable/disable logicJohannes Berg
Depending on the driver, having ARP filtering for some addresses may be possible. Remove the logic that tracks whether ARP filter is enabled or not and give the driver the total number of addresses instead of the length of the list so it can make its own decision. Reviewed-by: Luciano Coelho <coelho@ti.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-01-18mac80211: add op to configure default key idYoni Divinsky
There are hardwares which support offload of data packets for example when auto ARP is enabled the hw will send the ARP response. In such cases if WEP encryption is configured the hw must know the default WEP key in order to encrypt the packets correctly. When hw_accel is enabled and encryption type is set to WEP, the driver should get the default key index from mac80211. Signed-off-by: Yoni Divinsky <yoni.divinsky@ti.com> [cleanups, fixes, documentation] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-01-16mac80211: split out chandef tracing macrosJohannes Berg
Some new APIs will require tracing a chandef without it being part of a channel context, so separate out the tracing macros for that. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-01-16cfg80211: check radar interface combinationsSimon Wunderlich
To ease further DFS development regarding interface combinations, use the interface combinations structure to test for radar capabilities. Drivers can specify which channel widths they support, and in which modes. Right now only a single AP interface is allowed, but as the DFS code evolves other combinations can be enabled. Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-01-16cfg80211: Allow use_mfp to be specified with the connect commandJouni Malinen
The NL80211_ATTR_USE_MFP attribute was originally added for NL80211_CMD_ASSOCIATE, but it is actually as useful (if not even more useful) with NL80211_CMD_CONNECT, so process that attribute with the connect command, too. Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-01-16mac80211: add encrypt headroom to PERR framesBob Copeland
Mesh PERR action frames are robust and thus may be encrypted, so add proper head/tailroom to allow this. Fixes this warning when operating a Mesh STA on ath5k: WARNING: at net/mac80211/wpa.c:427 ccmp_encrypt_skb.isra.5+0x7b/0x1a0 [mac80211]() Call Trace: [<c011c5e7>] warn_slowpath_common+0x63/0x78 [<c011c60b>] warn_slowpath_null+0xf/0x13 [<e090621d>] ccmp_encrypt_skb.isra.5+0x7b/0x1a0 [mac80211] [<e090685c>] ieee80211_crypto_ccmp_encrypt+0x1f/0x37 [mac80211] [<e0917113>] invoke_tx_handlers+0xcad/0x10bd [mac80211] [<e0917665>] ieee80211_tx+0x87/0xb3 [mac80211] [<e0918932>] ieee80211_tx_pending+0xcc/0x170 [mac80211] [<c0121c43>] tasklet_action+0x3e/0x65 Signed-off-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-01-16mac80211: set NEED_TXPROCESSING for PERR framesBob Copeland
A user reported warnings in ath5k due to transmitting frames with no rates set up. The frames were Mesh PERR frames, and some debugging showed an empty control block with just the vif pointer: > [ 562.522682] XXX txinfo: 00000000: 00 00 00 00 00 00 00 00 00 00 00 > 00 00 00 00 00 ................ > [ 562.522688] XXX txinfo: 00000010: 00 00 00 00 00 00 00 00 54 b8 f2 > db 00 00 00 00 ........T....... > [ 562.522693] XXX txinfo: 00000020: 00 00 00 00 00 00 00 00 00 00 00 > 00 00 00 00 00 ................ Set the IEEE80211_TX_INTFL_NEED_TXPROCESSING flag to ensure that rate control gets run before the frame is sent. Signed-off-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-01-16nl80211: allow user-space to set address for P2P_DEVICEArend van Spriel
As per email discussion Jouni Malinen pointed out that: "P2P message exchanges can be executed on the current operating channel of any operation (both P2P and non-P2P station). These can be on 5 GHz and even on 60 GHz (so yes, you _can_ do GO Negotiation on 60 GHz). As an example, it would be possible to receive a GO Negotiation Request frame on a 5 GHz only radio and then to complete GO Negotiation on that band. This can happen both when connected to a P2P group (through client discoverability mechanism) and when connected to a legacy AP (assuming the station receive Probe Request frame from full scan in the beginning of P2P device discovery)." This means that P2P messages can be sent over different radio devices. However, these should use the same P2P device address so it should be able to provision this from user-space. This patch adds a parameter for this to struct vif_params which should only be used during creation of the P2P device interface. Cc: Jouni Malinen <j@w1.fi> Cc: Greg Goldman <ggoldman@broadcom.com> Cc: Jithu Jance <jithu@broadcom.com> Signed-off-by: Arend van Spriel <arend@broadcom.com> [add error checking] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-01-16{cfg,nl}80211: mesh power mode primitives and userspace accessMarco Porsch
Add the nl80211_mesh_power_mode enumeration which holds possible values for the mesh power mode. These modes are unknown, active, light sleep and deep sleep. Add power_mode entry to the mesh config structure to hold the user-configured default mesh power mode. This value will be used for new peer links. Add the dot11MeshAwakeWindowDuration value to the mesh config. The awake window is a duration in TU describing how long the STA will stay awake after transmitting its beacon in PS mode. Add access routines to: - get/set local link-specific power mode (STA) - get remote STA's link-specific power mode (STA) - get remote STA's non-peer power mode (STA) - get/set default mesh power mode (mesh config) - get/set mesh awake window duration (mesh config) All config changes may be done at mesh runtime and take effect immediately. Signed-off-by: Marco Porsch <marco@cozybit.com> Signed-off-by: Ivan Bezyazychnyy <ivan.bezyazychnyy@gmail.com> Signed-off-by: Mike Krinkin <krinkin.m.u@gmail.com> [fix commit message line length, error handling in set station] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-01-16{cfg,nl,mac}80211: set beacon interval and DTIM period on mesh joinMarco Porsch
Move the default mesh beacon interval and DTIM period to cfg80211 and make them accessible to nl80211. This enables setting both values when joining an MBSS. Previously the DTIM parameter was not set by mac80211 so the driver's default value was used. Signed-off-by: Marco Porsch <marco@cozybit.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-01-16mac80211: move add_tim to subfunctionMarco Porsch
This functions will be used for mesh beacons, too. Signed-off-by: Marco Porsch <marco@cozybit.com> [some formatting fixes] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-01-16mac80211: update mesh peer link counter during userspace peeringMarco Porsch
The established peer link count is indicated in mesh beacons and used for other internal tasks. Previously it was not updated when authenticated peering is performed in userspace. Signed-off-by: Marco Porsch <marco@cozybit.com> Acked-by: Thomas Pedersen <thomas@cozybit.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-01-16nl80211: add range checks to mesh parametersMarco Porsch
Ranges are taken from IEEE 802.11-2012, common sense or current implementation requirements. Signed-off-by: Marco Porsch <marco@cozybit.com> Acked-by: Thomas Pedersen <thomas@cozybit.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-01-16mac80211: allow disable power save in meshChun-Yeow Yeoh
Allow mesh interface to disable the power save which is by default turn on in certain chipset. Testing with 2 units of ZCN-1523H-5-16 featuring AR9280 chipset which have power save enabled by default. Constant reset if the average signal of the peer mesh STA is below -80 dBm and power save is enabled. Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-01-16mac80211: call restart complete at wowlan resume timeJohannes Berg
When the driver's resume function can't completely restore the configuration in the device, it returns 1 from the callback which will be treated like a HW restart request, but done directly. In this case, also call the driver's restart_complete() function so it can finish the reconfiguration there. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-01-16mac80211: fix resume from WoWLANJohannes Berg
My commit 529ba6e9313dbe60dab7e72c6fdf647a012e9f5b ("mac80211: clean up association better in suspend") introduced a bug when resuming from WoWLAN when a device reset is desired. This case must not use the suspend_bss_conf as it hasn't been stored. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-01-16mac80211: fix monitor mode injectionFelix Fietkau
Channel contexts are not always used with monitor interfaces. If no channel context is set, use the oper channel, otherwise tx fails. Signed-off-by: Felix Fietkau <nbd@openwrt.org> [check local->use_chanctx] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-01-16mac80211: synchronize scan off/on-channel and PS statesStanislaw Gruszka
Since: commit b23b025fe246f3acc2988eb6d400df34c27cb8ae Author: Ben Greear <greearb@candelatech.com> Date: Fri Feb 4 11:54:17 2011 -0800 mac80211: Optimize scans on current operating channel. we do not disable PS while going back to operational channel (on ieee80211_scan_state_suspend) and deffer that until scan finish. But since we are allowed to send frames, we can send a frame to AP without PM bit set, so disable PS on AP side. Then when we switch to off-channel (in ieee80211_scan_state_resume) we do not enable PS. Hence we are off-channel with PS disabled, frames are not buffered by AP. To fix remove offchannel_ps_disable argument and always enable PS when going off-channel and disable it when going on-channel, like it was before. Cc: stable@vger.kernel.org # 2.6.39+ Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Tested-by: Seth Forshee <seth.forshee@canonical.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-01-16mac80211: fix FT roamingJohannes Berg
During FT roaming, wpa_supplicant attempts to set the key before association. This used to be rejected, but as a side effect of my commit 66e67e418908442389d3a9e ("mac80211: redesign auth/assoc") the key was accepted causing hardware crypto to not be used for it as the station isn't added to the driver yet. It would be possible to accept the key and then add it to the driver when the station has been added. However, this may run into issues with drivers using the state- based station adding if they accept the key only after association like it used to be. For now, revert to the behaviour from before the auth and assoc change. Cc: stable@vger.kernel.org Reported-by: Cédric Debarge <cedric.debarge@acksys.fr> Tested-by: Cédric Debarge <cedric.debarge@acksys.fr> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2013-01-14Merge tag 'nfc-next-3.9-1' of ↵John W. Linville
git://git.kernel.org/pub/scm/linux/kernel/git/sameo/nfc-next Samuel Ortiz <sameo@linux.intel.com> says: "This is the first NFC patchset targeted at the 3.9 merge window. It brings the following goodies: - LLCP socket timestamping (To be used e.g with the recently released nfctool application for a more efficient skb timestamping when sniffing). - A pretty big pn533 rework from Waldemar, preparing the driver to support more flavours of pn533 based devices. - HCI changes from Eric in preparation for the microread driver support. - Some LLCP memory leak fixes, cleanups and slight improvements. - pn544 and nfcwilink move to the devm_kzalloc API. - An initial Secure Element (SE) API. - An nfc.h license change from the original author, allowing non GPL application code to safely include it." Signed-off-by: John W. Linville <linville@tuxdriver.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-05 11:45:55 +0000