| Age | Commit message (Collapse) | Author |
|---|
|
For robustness protect of higher port numbers than expected to avoid
setting bits behind our port_event_mask. In case of an DEVICE_FATAL
event all ports must be checked. The IB_EVENT_GID_CHANGE event is
provided in the global event handler, so handle it there. And handle a
QP_FATAL event instead of an DEVICE_FATAL event in the qp handler.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove the shortcut that smc_lgr_free() would skip the check for
existing connections when the link group is not in the link group list.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In smc_cdc_msg_recv_action() the received cdc message is evaluated.
To reduce the number of messaged triggered by this evaluation the logic
is streamlined. For the write_blocked condition we do not need to send
a response immediately. The remaining conditions can be put together
into one if clause.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When no free transfer buffers are available then a work to call
smc_tx_work() is scheduled. Set the schedule delay to zero, because for
the out-of-buffers condition the work can start immediately and will
block in the called function smc_wr_tx_get_free_slot(), waiting for free
buffers.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move the call to smc_close_wake_tx_prepared() (which wakes up a possibly
waiting close processing that might wait for 'all data sent') to
smc_tx_sndbuf_nonempty() (which is the main function to send data).
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When an updated rx_cursor_confirmed field was sent to the peer then
reset the cons_curs_upd_req flag. And remove the duplicate reset and
cursor update in smc_tx_consumer_update().
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Number of devlink attributes has grown over 128, causing the
following warning:
../net/core/devlink.c: In function ‘devlink_nl_cmd_region_read_dumpit’:
../net/core/devlink.c:3740:1: warning: the frame size of 1064 bytes is larger than 1024 bytes [-Wframe-larger-than=]
}
^
Since the number of attributes is only going to grow allocate
the array dynamically.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We need the port to be both ethernet and have the rigth netdev,
not one or the other.
Fixes: ddb6e99e2db1 ("ethtool: add compat for devlink info")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add WARN_ON to make sure that all sub objects of a devlink device are
cleanedup before freeing the devlink device.
This helps to catch any driver bugs.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The flag offload_fwd_mark is set as the switch can forward frames by
itself.
This can be considered a fix to a problem introduced in commit
c2e866911e254067 where the port membership are not set in sync. The flag
offload_fwd_mark just needs to be set in tag_ksz.c to prevent the software
bridge from forwarding duplicate multicast frames.
Fixes: c2e866911e254067 ("microchip: break KSZ9477 DSA driver into two files")
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Modify the kernel users of the TCA_ACT_* macros to use TCA_ID_*. For
example, use TCA_ID_GACT instead of TCA_ACT_GACT. This will align with
TCA_ID_POLICE and also differentiates these identifier, used in struct
tc_action_ops type field, from other macros starting with TCA_ACT_.
To make things clearer, we name the enum defining the TCA_ID_*
identifiers and also change the "type" field of struct tc_action to
id.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move all the TC identifiers to one place, to the same enum that defines
the identifier of police action. This makes it easier choose numbers for
new actions since they are now defined in one place. We preserve the
original values for binary compatibility. New IDs should be added inside
the enum.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Function tls_sw_recvmsg() dequeues multiple records from stream parser
and decrypts them. In case the decryption is done by async accelerator,
the records may get submitted for decryption while the previous ones may
not have been decryted yet. For tls1.3, the record type is known only
after decryption. Therefore, for tls1.3, tls_sw_recvmsg() may submit
records for decryption even if it gets 'handshake' records after 'data'
records. These intermediate 'handshake' records may do a key updation.
By the time new keys are given to ktls by userspace, it is possible that
ktls has already submitted some records i(which are encrypted with new
keys) for decryption using old keys. This would lead to decrypt failure.
Therefore, async decryption of records should be disabled for tls1.3.
Fixes: 130b392c6cd6b ("net: tls: Add tls 1.3 support")
Signed-off-by: Vakul Garg <vakul.garg@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
net/core/ethtool.c:3023:19: warning: address of array
'ext_m_spec->h_dest' will always evaluate to 'true'
[-Wpointer-bool-conversion]
if (ext_m_spec->h_dest) {
~~ ~~~~~~~~~~~~^~~~~~
h_dest is an array, it can't be null so remove this check.
Fixes: eca4205f9ec3 ("ethtool: add ethtool_rx_flow_spec to flow_rule structure translator")
Link: https://github.com/ClangBuiltLinux/linux/issues/353
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
struct boo entry[];
};
size = sizeof(struct foo) + count * sizeof(struct boo);
instance = alloc(size, GFP_KERNEL)
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = alloc(struct_size(instance, entry, count), GFP_KERNEL)
Notice that, in this case, variable size is not necessary, hence it is
removed.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
struct boo entry[];
};
instance = alloc(sizeof(struct foo) + count * sizeof(struct boo));
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = alloc(struct_size(instance, entry, count));
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
struct boo entry[];
};
size = sizeof(struct foo) + count * sizeof(struct boo);
instance = alloc(size, GFP_KERNEL)
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
size = struct_size(instance, entry, count);
instance = alloc(size, GFP_KERNEL)
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
struct boo entry[];
};
size = sizeof(struct foo) + count * sizeof(struct boo);
instance = alloc(size, GFP_KERNEL)
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
size = struct_size(instance, entry, count);
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, user can do dump or get of param values right after the
devlink params are registered. However the driver may not be initialized
which is an issue. The same problem happens during notification
upon param registration. Allow driver to publish devlink params
whenever it is ready to handle get() ops. Note that this cannot
be resolved by init reordering, as the "driverinit" params have
to be available before the driver is initialized (it needs the param
values there).
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Cc: Michael Chan <michael.chan@broadcom.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
An ipvlan bug fix in 'net' conflicted with the abstraction away
of the IPV6 specific support in 'net-next'.
Similarly, a bug fix for mlx5 in 'net' conflicted with the flow
action conversion in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes from David Miller:
"This pull request is dedicated to the upcoming snowpocalypse parts 2
and 3 in the Pacific Northwest:
1) Drop profiles are broken because some drivers use dev_kfree_skb*
instead of dev_consume_skb*, from Yang Wei.
2) Fix IWLWIFI kconfig deps, from Luca Coelho.
3) Fix percpu maps updating in bpftool, from Paolo Abeni.
4) Missing station release in batman-adv, from Felix Fietkau.
5) Fix some networking compat ioctl bugs, from Johannes Berg.
6) ucc_geth must reset the BQL queue state when stopping the device,
from Mathias Thore.
7) Several XDP bug fixes in virtio_net from Toshiaki Makita.
8) TSO packets must be sent always on queue 0 in stmmac, from Jose
Abreu.
9) Fix socket refcounting bug in RDS, from Eric Dumazet.
10) Handle sparse cpu allocations in bpf selftests, from Martynas
Pumputis.
11) Make sure mgmt frames have enough tailroom in mac80211, from Felix
Feitkau.
12) Use safe list walking in sctp_sendmsg() asoc list traversal, from
Greg Kroah-Hartman.
13) Make DCCP's ccid_hc_[rt]x_parse_options always check for NULL
ccid, from Eric Dumazet.
14) Need to reload WoL password into bcmsysport device after deep
sleeps, from Florian Fainelli.
15) Remove filter from mask before freeing in cls_flower, from Petr
Machata.
16) Missing release and use after free in error paths of s390 qeth
code, from Julian Wiedmann.
17) Fix lockdep false positive in dsa code, from Marc Zyngier.
18) Fix counting of ATU violations in mv88e6xxx, from Andrew Lunn.
19) Fix EQ firmware assert in qed driver, from Manish Chopra.
20) Don't default Caivum PTP to Y in kconfig, from Bjorn Helgaas"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (116 commits)
net: dsa: b53: Fix for failure when irq is not defined in dt
sit: check if IPv6 enabled before calling ip6_err_gen_icmpv6_unreach()
geneve: should not call rt6_lookup() when ipv6 was disabled
net: Don't default Cavium PTP driver to 'y'
net: broadcom: replace dev_kfree_skb_irq by dev_consume_skb_irq for drop profiles
net: via-velocity: replace dev_kfree_skb_irq by dev_consume_skb_irq for drop profiles
net: tehuti: replace dev_kfree_skb_irq by dev_consume_skb_irq for drop profiles
net: sun: replace dev_kfree_skb_irq by dev_consume_skb_irq for drop profiles
net: fsl_ucc_hdlc: replace dev_kfree_skb_irq by dev_consume_skb_irq for drop profiles
net: fec_mpc52xx: replace dev_kfree_skb_irq by dev_consume_skb_irq for drop profiles
net: smsc: epic100: replace dev_kfree_skb_irq by dev_consume_skb_irq for drop profiles
net: dscc4: replace dev_kfree_skb_irq by dev_consume_skb_irq for drop profiles
net: tulip: de2104x: replace dev_kfree_skb_irq by dev_consume_skb_irq for drop profiles
net: defxx: replace dev_kfree_skb_irq by dev_consume_skb_irq for drop profiles
net/mlx5e: Don't overwrite pedit action when multiple pedit used
net/mlx5e: Update hw flows when encap source mac changed
qed*: Advance drivers version to 8.37.0.20
qed: Change verbosity for coalescing message.
qede: Fix system crash on configuring channels.
qed: Consider TX tcs while deriving the max num_queues for PF.
...
|
|
Commit ed75986f4aae ("net/smc: ipv6 support for smc_diag.c") changed the
value of the diag_family field. The idea was to indicate the family of
the IP address in the inet_diag_sockid field. But the change makes it
impossible to distinguish an inet_sock_diag response message from SMC
sock_diag response. This patch restores the original behaviour and sends
AF_SMC as value of the diag_family field.
Fixes: ed75986f4aae ("net/smc: ipv6 support for smc_diag.c")
Reported-by: Eugene Syromiatnikov <esyr@redhat.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The lgr field of an smc_connection is set in smc_conn_create() and
should be cleared in smc_conn_free() for consistency reasons, so move
the responsible code.
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If SMC client and server connections are both established at the same
time, smc_connect_rdma() cannot send a CLC confirm message while
smc_listen_work() is waiting for one due to lock contention. This can
result in timeouts in smc_clc_wait_msg() and failed SMC connections.
In case of SMC-R, there are two types of LGRs (client and server LGRs)
which can be protected by separate locks. So, this patch splits the LGR
pending lock into two separate locks for client and server to avoid the
locking issue for SMC-R.
Signed-off-by: Hans Wippel <hwippel@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If SMC client and server connections are both established at the same
time, smc_connect_ism() cannot send a CLC confirm message while
smc_listen_work() is waiting for one due to lock contention. This can
result in timeouts in smc_clc_wait_msg() and failed SMC connections.
In case of SMC-D, the LGR pending lock is not needed while
smc_listen_work() is waiting for the CLC confirm message. So, this patch
releases the lock earlier for SMC-D to avoid the locking issue.
Signed-off-by: Hans Wippel <hwippel@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
SMC already provides a wrapper for atomic64 calls to be
architecture independent. Use this wrapper for SMC-D as well.
Reported-by: Jens Remus <jremus@linux.ibm.com>
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
According to RFC7609 (http://www.rfc-editor.org/info/rfc7609)
first the SMC-R connection is shut down and then the normal TCP
connection FIN processing drives cleanup of the internal TCP connection.
The unconditional release of the clcsock during active socket closing
has to be postponed if the peer has not yet signalled socket closing.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If we disabled IPv6 from the kernel command line (ipv6.disable=1), we should
not call ip6_err_gen_icmpv6_unreach(). This:
ip link add sit1 type sit local 192.0.2.1 remote 192.0.2.2 ttl 1
ip link set sit1 up
ip addr add 198.51.100.1/24 dev sit1
ping 198.51.100.2
if IPv6 is disabled at boot time, will crash the kernel.
v2: there's no need to use in6_dev_get(), use __in6_dev_get() instead,
as we only need to check that idev exists and we are under
rcu_read_lock() (from netif_receive_skb_internal()).
Reported-by: Jianlin Shi <jishi@redhat.com>
Fixes: ca15a078bd90 ("sit: generate icmpv6 error when receiving icmpv4 error")
Cc: Oussama Ghorbel <ghorbel@pivasoftware.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add devlink health dump commands, in order to run an dump operation
over a specific reporter.
The supported operations are dump_get in order to get last saved
dump (if not exist, dump now) and dump_clear to clear last saved
dump.
It is expected from driver's callback for diagnose command to fill it
via the devlink fmsg API. Devlink will parse it and convert it to
netlink nla API in order to pass it to the user.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add devlink health diagnose command, in order to run a diagnose
operation over a specific reporter.
It is expected from driver's callback for diagnose command to fill it
via the devlink fmsg API. Devlink will parse it and convert it to
netlink nla API in order to pass it to the user.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add devlink health recover command to the uapi, in order to allow the user
to execute a recover operation over a specific reporter.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add devlink health set command, in order to set configuration parameters
for a specific reporter.
Supported parameters are:
- graceful_period: Time interval between auto recoveries (in msec)
- auto_recover: Determines if the devlink shall execute recover upon
receiving error for the reporter
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add devlink health get command to provide reporter/s data for user space.
Add the ability to get data per reporter or dump data from all available
reporters.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Upon error discover, every driver can report it to the devlink health
mechanism via devlink_health_report function, using the appropriate
reporter registered to it. Driver can pass error specific context which
will be delivered to it as part of the dump / recovery callbacks.
Once an error is reported, devlink health will do the following actions:
* A log is being send to the kernel trace events buffer
* Health status and statistics are being updated for the reporter instance
* Object dump is being taken and stored at the reporter instance (as long
as there is no other dump which is already stored)
* Auto recovery attempt is being done. Depends on:
- Auto Recovery configuration
- Grace period vs. Time since last recover
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Devlink health reporter is an instance for reporting, diagnosing and
recovering from run time errors discovered by the reporters.
Define it's data structure and supported operations.
In addition, expose devlink API to create and destroy a reporter.
Each devlink instance will hold it's own reporters list.
As part of the allocation, driver shall provide a set of callbacks which
will be used by devlink in order to handle health reports and user
commands related to this reporter. In addition, driver is entitled to
provide some priv pointer, which can be fetched from the reporter by
devlink_health_reporter_priv function.
For each reporter, devlink will hold a metadata of statistics,
dump msg and status.
For passing dumps and diagnose data to the user-space, it will use devlink
fmsg API.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Devlink fmsg is a mechanism to pass descriptors between drivers and
devlink, in json-like format. The API allows the driver to add nested
attributes such as object, object pair and value array, in addition to
attributes such as name and value.
Driver can use this API to fill the fmsg context in a format which will be
translated by the devlink to the netlink message later.
There is no memory allocation in advance (other than the initial list
head), and it dynamically allocates messages descriptors and add them to
the list on the fly.
When it needs to send the data using SKBs to the netlink layer, it
fragments the data between different SKBs. In order to do this
fragmentation, it uses virtual nests attributes, to avoid actual
nesting use which cannot be divided between different SKBs.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux
Santosh Shilimkar says:
====================
rds: add tos support
RDS applications make use of tos to classify database traffic.
This feature has been used in shipping products from 2.6.32 based
kernels. Its tied with RDS v4.1 protocol version and the compatibility
gets negotiated as part of connections setup.
Patchset keeps full backward compatibility using existing connection
negotiation scheme. Currently the feature is exploited by RDMA
transport and for TCP transport the user tos values are mapped to
same default class (0).
For RDMA transports, RDMA CM service type API is used to
set up different SL(service lanes) and the IB fabric is configured
for tos mapping using Subnet Manager(SL to VL mappings).
Similarly for ROCE fabric, user priority is mapped with different
DSCP code points which are associated with different switch queues
in the fabric.
The original code was developed by Bang Nguyen in downstream kernel back in
2.6.32 kernel days and it has evolved significantly over period of time.
Thanks to Yanjun for doing testing with various combinations of host like
v3.1<->v4.1, v4.1.<->v3.1, v4.1 upstream to shipping v4.1 etc etc
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Daniel Borkmann says:
====================
pull-request: bpf-next 2019-02-07
The following pull-request contains BPF updates for your *net-next* tree.
The main changes are:
1) Add a riscv64 JIT for BPF, from Björn.
2) Implement BTF deduplication algorithm for libbpf which takes BTF type
information containing duplicate per-compilation unit information and
reduces it to an equivalent set of BTF types with no duplication and
without loss of information, from Andrii.
3) Offloaded and native BPF XDP programs can coexist today, enable also
offloaded and generic ones as well, from Jakub.
4) Expose various BTF related helper functions in libbpf as API which
are in particular helpful for JITed programs, from Yonghong.
5) Fix the recently added JMP32 code emission in s390x JIT, from Heiko.
6) Fix BPF kselftests' tcp_{server,client}.py to be able to run inside
a network namespace, also add a fix for libbpf to get libbpf_print()
working, from Stanislav.
7) Fixes for bpftool documentation, from Prashant.
8) Type cleanup in BPF kselftests' test_maps.c to silence a gcc8 warning,
from Breno.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that we have a dedicated NDO for getting a port's parent ID, get rid
of SWITCHDEV_ATTR_ID_PORT_PARENT_ID and convert all callers to use the
NDO exclusively. This is a preliminary change to getting rid of
switchdev_ops eventually.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
DSA implements SWITCHDEV_ATTR_ID_PORT_PARENT_ID and we want to get rid
of switchdev_ops eventually, ease that migration by implementing a
ndo_get_port_parent_id() function which returns what
switchdev_port_attr_get() would do.
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation for getting rid of switchdev_ops, create a dedicated NDO
operation for getting the port's parent identifier. There are
essentially two classes of drivers that need to implement getting the
port's parent ID which are VF/PF drivers with a built-in switch, and
pure switchdev drivers such as mlxsw, ocelot, dsa etc.
We introduce a helper function: dev_get_port_parent_id() which supports
recursion into the lower devices to obtain the first port's parent ID.
Convert the bridge, core and ipv4 multicast routing code to check for
such ndo_get_port_parent_id() and call the helper function when valid
before falling back to switchdev_port_attr_get(). This will allow us to
convert all relevant drivers in one go instead of having to implement
both switchdev_port_attr_get() and ndo_get_port_parent_id() operations,
then get rid of switchdev_port_attr_get().
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This function can't succeed if dp->pl is NULL. It will Oops inside the
call to return phylink_ethtool_get_eee(dp->pl, e);
Fixes: 1be52e97ed3e ("dsa: slave: eee: Allow ports to use phylink")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Two and a half years ago, the client was changed to use gathered
Send for larger inline messages, in commit 655fec6987b ("xprtrdma:
Use gathered Send for large inline messages"). Several fixes were
required because there are a few in-kernel device drivers whose
max_sge is 3, and these were broken by the change.
Apparently my memory is going, because some time later, I submitted
commit 25fd86eca11c ("svcrdma: Don't overrun the SGE array in
svc_rdma_send_ctxt"), and after that, commit f3c1fd0ee294 ("svcrdma:
Reduce max_send_sges"). These too incorrectly assumed in-kernel
device drivers would have more than a few Send SGEs available.
The fix for the server side is not the same. This is because the
fundamental problem on the server is that, whether or not the client
has provisioned a chunk for the RPC reply, the server must squeeze
even the most complex RPC replies into a single RDMA Send. Failing
in the send path because of Send SGE exhaustion should never be an
option.
Therefore, instead of failing when the send path runs out of SGEs,
switch to using a bounce buffer mechanism to handle RPC replies that
are too complex for the device to send directly. That allows us to
remove the max_sge check to enable drivers with small max_sge to
work again.
Reported-by: Don Dutile <ddutile@redhat.com>
Fixes: 25fd86eca11c ("svcrdma: Don't overrun the SGE array in ...")
Cc: stable@vger.kernel.org
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
|
|
Define a tracepoint and allow user to trace messages in case of an hardware
error code for hardware associated with devlink instance.
Signed-off-by: Nir Dotan <nird@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When either "goto wait_interrupted;" or "goto wait_error;"
paths are taken, socket lock has already been released.
This patch fixes following syzbot splat :
WARNING: bad unlock balance detected!
5.0.0-rc4+ #59 Not tainted
-------------------------------------
syz-executor223/8256 is trying to release lock (sk_lock-AF_RXRPC) at:
[<ffffffff86651353>] rxrpc_recvmsg+0x6d3/0x3099 net/rxrpc/recvmsg.c:598
but there are no more locks to release!
other info that might help us debug this:
1 lock held by syz-executor223/8256:
#0: 00000000fa9ed0f4 (slock-AF_RXRPC){+...}, at: spin_lock_bh include/linux/spinlock.h:334 [inline]
#0: 00000000fa9ed0f4 (slock-AF_RXRPC){+...}, at: release_sock+0x20/0x1c0 net/core/sock.c:2798
stack backtrace:
CPU: 1 PID: 8256 Comm: syz-executor223 Not tainted 5.0.0-rc4+ #59
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x172/0x1f0 lib/dump_stack.c:113
print_unlock_imbalance_bug kernel/locking/lockdep.c:3391 [inline]
print_unlock_imbalance_bug.cold+0x114/0x123 kernel/locking/lockdep.c:3368
__lock_release kernel/locking/lockdep.c:3601 [inline]
lock_release+0x67e/0xa00 kernel/locking/lockdep.c:3860
sock_release_ownership include/net/sock.h:1471 [inline]
release_sock+0x183/0x1c0 net/core/sock.c:2808
rxrpc_recvmsg+0x6d3/0x3099 net/rxrpc/recvmsg.c:598
sock_recvmsg_nosec net/socket.c:794 [inline]
sock_recvmsg net/socket.c:801 [inline]
sock_recvmsg+0xd0/0x110 net/socket.c:797
__sys_recvfrom+0x1ff/0x350 net/socket.c:1845
__do_sys_recvfrom net/socket.c:1863 [inline]
__se_sys_recvfrom net/socket.c:1859 [inline]
__x64_sys_recvfrom+0xe1/0x1a0 net/socket.c:1859
do_syscall_64+0x103/0x610 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x446379
Code: e8 2c b3 02 00 48 83 c4 18 c3 0f 1f 80 00 00 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 2b 09 fc ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:00007fe5da89fd98 EFLAGS: 00000246 ORIG_RAX: 000000000000002d
RAX: ffffffffffffffda RBX: 00000000006dbc28 RCX: 0000000000446379
RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000003
RBP: 00000000006dbc20 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00000000006dbc2c
R13: 0000000000000000 R14: 0000000000000000 R15: 20c49ba5e353f7cf
Fixes: 248f219cb8bc ("rxrpc: Rewrite the data and ack handling code")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: David Howells <dhowells@redhat.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds a function to translate the ethtool_rx_flow_spec
structure to the flow_rule representation.
This allows us to reuse code from the driver side given that both flower
and ethtool_rx_flow interfaces use the same representation.
This patch also includes support for the flow type flags FLOW_EXT,
FLOW_MAC_EXT and FLOW_RSS.
The ethtool_rx_flow_spec_input wrapper structure is used to convey the
rss_context field, that is away from the ethtool_rx_flow_spec structure,
and the ethtool_rx_flow_spec structure.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that drivers have been converted to use the flow action
infrastructure, remove this field from the tc_cls_flower_offload
structure.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch provides the flow_stats structure that acts as container for
tc_cls_flower_offload, then we can use to restore the statistics on the
existing TC actions. Hence, tcf_exts_stats_update() is not used from
drivers anymore.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch implements a new function to translate from native TC action
to the new flow_action representation. Moreover, this patch also updates
cls_flower to use this new function.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This new infrastructure defines the nic actions that you can perform
from existing network drivers. This infrastructure allows us to avoid a
direct dependency with the native software TC action representation.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
