summaryrefslogtreecommitdiff
path: root/net
AgeCommit message (Collapse)Author
2010-12-20mac80211: skip unnecessary pskb_expand_head callsFelix Fietkau
If the skb is not cloned and we don't need any extra headroom, there is no point in reallocating the skb head. Signed-off-by: Felix Fietkau <nbd@openwrt.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-20mac80211: fix initialization of skb->cb in ieee80211_subif_start_xmitFelix Fietkau
The change 'mac80211: Fix BUG in pskb_expand_head when transmitting shared skbs' added a check for copying the skb if it's shared, however the tx info variable still points at the cb of the old skb Signed-off-by: Felix Fietkau <nbd@openwrt.org> Acked-by: Helmut Schaa <helmut.schaa@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-20mac80211: Remove unused third address from mesh address extension header.Javier Cardona
The Mesh Control header only includes 0, 1 or 2 addresses. If there is one address, it should be interpreted as Address 4. If there are 2, they are interpreted as Addresses 5 and 6 (Address 4 being the 4th address in the 802.11 header). The address extension used to hold up to 3 addresses instead of the current 2. I'm not sure which draft version changed this, but it is very unlikely that it will change again given the state of the approval process of this draft. See section 7.1.3.6.3 in current draft (8.0). Also, note that the extra address that I'm removing was not being used, so this change has no effect on over-the-air frame formats. But I thought I better remove it before someone does start using it. Signed-off-by: Javier Cardona <javier@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-20nl80211: Export available antennasBruno Randolf
Export the information which antennas are available for configuration as TX or RX antennas via nl80211. Signed-off-by: Bruno Randolf <br1@einfach.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-20cfg80211: Separate available antennas for RX and TXBruno Randolf
As has been pointed out by Daniel Halperin some devices (e.g. Intel IWL5100) can only TX from a subset of RX antennas, so use separate availability masks for RX and TX. Signed-off-by: Bruno Randolf <br1@einfach.org> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-20mac80211: Send mesh non-HWMP path selection frames to userspaceJavier Cardona
Let path selection frames for protocols other than HWMP be sent to userspace via NL80211_CMD_REGISTER_FRAME. Also allow userspace to send and receive mesh path selection frames. Signed-off-by: Javier Cardona <javier@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-20mac80211: Let userspace enable and configure vendor specific path selection.Javier Cardona
Userspace will now be allowed to toggle between the default path selection algorithm (HWMP, implemented in the kernel), and a vendor specific alternative. Also in the same patch, allow userspace to add information elements to mesh beacons. This is accordance with the Extensible Path Selection Framework specified in version 7.0 of the 802.11s draft. Signed-off-by: Javier Cardona <javier@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-20mac80211: Rename mesh_params to mesh_config to prepare for mesh_setupJavier Cardona
Mesh parameters can be to setup a mesh or to configure it. This patch renames the ambiguous name mesh_params to mesh_config in preparation for mesh_setup. Signed-off-by: Javier Cardona <javier@cozybit.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-20ipv4: Flush per-ns routing cache more sanely.David S. Miller
Flush the routing cache only of entries that match the network namespace in which the purge event occurred. Signed-off-by: David S. Miller <davem@davemloft.net> Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
2010-12-20batman-adv: Return hna count on local buffer fillSven Eckelmann
hna_local_fill_buffer must return the number of added hna entries and not the last checked hash bucket. Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-12-20pktgen: Remove unnecessary prefix from pr_<level>Joe Perches
Remove "pktgen: " prefix string from one pr_info. pr_fmt adds it, so this is a duplicate. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-12-19net: kill unused macrosShan Wei
These macros never be used, so remove them. Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-12-19net: increase skb->users instead of skb_clone()Changli Gao
In dev_queue_xmit_nit(), we have to clone skbs as we need to mangle skbs, however, we don't need to clone skbs for all the packet_types. Except for the first packet_type, we increase skb->users instead of skb_clone(). Signed-off-by: Changli Gao <xiaosuo@gmail.com> Acked-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-12-19ipv6: Fragment locally generated tunnel-mode IPSec6 packets as needed.David Stevens
This patch modifies IPsec6 to fragment IPv6 packets that are locally generated as needed. This version of the patch only fragments in tunnel mode, so that fragment headers will not be obscured by ESP in transport mode. Signed-off-by: David L Stevens <dlstevens@us.ibm.com> Acked-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-12-18ipv6: remove duplicate neigh_ifdownstephen hemminger
When device is being set to down, neigh_ifdown was being called twice. Once from addrconf notifier and once from ndisc notifier. Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-12-18ipv6: fib6_ifdown cleanupstephen hemminger
Remove (unnecessary) casts to make code cleaner. Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-12-17Merge branch 'master' of ↵David S. Miller
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6 Conflicts: drivers/net/bnx2x/bnx2x.h drivers/net/wireless/iwlwifi/iwl-1000.c drivers/net/wireless/iwlwifi/iwl-6000.c drivers/net/wireless/iwlwifi/iwl-core.h drivers/vhost/vhost.c
2010-12-17ceph: handle partial result from get_user_pagesHenry C Chang
The get_user_pages() helper can return fewer than the requested pages. Error out in that case, and clean up the partial result. Signed-off-by: Henry C Chang <henry_c_chang@tcloudcomputing.com> Signed-off-by: Sage Weil <sage@newdream.net>
2010-12-17ceph: mark user pages dirty on direct-io readsHenry C Chang
For read operation, we have to set the argument _write_ of get_user_pages to 1 since we will write data to pages. Also, we need to SetPageDirty before releasing these pages. Signed-off-by: Henry C Chang <henry_c_chang@tcloudcomputing.com> Signed-off-by: Sage Weil <sage@newdream.net>
2010-12-16ipv6: don't flush routes when setting loopback downstephen hemminger
When loopback device is being brought down, then keep the route table entries because they are special. The entries in the local table for linklocal routes and ::1 address should not be purged. This is a sub optimal solution to the problem and should be replaced by a better fix in future. Signed-off-by: Stephen Hemminger <shemminger@vyatta.com> Acked-by: "Eric W. Biederman" <ebiederm@xmission.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-12-16sctp: fix the return value of getting the sctp partial delivery pointWei Yongjun
Get the sctp partial delivery point using SCTP_PARTIAL_DELIVERY_POINT socket option should return 0 if success, not -ENOTSUPP. Signed-off-by: Wei Yongjun <yjwei@cn.fujitsu.com> Acked-by: Vlad Yasevich <vladislav.yasevich@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-12-16net: Use skb_checksum_start_offset()Michał Mirosław
Replace skb->csum_start - skb_headroom(skb) with skb_checksum_start_offset(). Note for usb/smsc95xx: skb->data - skb->head == skb_headroom(skb). Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-12-16bridge: fix IPv6 queries for bridge multicast snoopingDavid Stevens
This patch fixes a missing ntohs() for bridge IPv6 multicast snooping. Signed-off-by: David L Stevens <dlstevens@us.ibm.com> Acked-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-12-16net: fix nulls list corruptions in sk_prot_allocOctavian Purdila
Special care is taken inside sk_port_alloc to avoid overwriting skc_node/skc_nulls_node. We should also avoid overwriting skc_bind_node/skc_portaddr_node. The patch fixes the following crash: BUG: unable to handle kernel paging request at fffffffffffffff0 IP: [<ffffffff812ec6dd>] udp4_lib_lookup2+0xad/0x370 [<ffffffff812ecc22>] __udp4_lib_lookup+0x282/0x360 [<ffffffff812ed63e>] __udp4_lib_rcv+0x31e/0x700 [<ffffffff812bba45>] ? ip_local_deliver_finish+0x65/0x190 [<ffffffff812bbbf8>] ? ip_local_deliver+0x88/0xa0 [<ffffffff812eda35>] udp_rcv+0x15/0x20 [<ffffffff812bba45>] ip_local_deliver_finish+0x65/0x190 [<ffffffff812bbbf8>] ip_local_deliver+0x88/0xa0 [<ffffffff812bb2cd>] ip_rcv_finish+0x32d/0x6f0 [<ffffffff8128c14c>] ? netif_receive_skb+0x99c/0x11c0 [<ffffffff812bb94b>] ip_rcv+0x2bb/0x350 [<ffffffff8128c14c>] netif_receive_skb+0x99c/0x11c0 Signed-off-by: Leonard Crestez <lcrestez@ixiacom.com> Signed-off-by: Octavian Purdila <opurdila@ixiacom.com> Acked-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-12-16net: factorize sync-rcu call in unregister_netdevice_manyOctavian Purdila
Add dev_close_many and dev_deactivate_many to factorize another sync-rcu operation on the netdevice unregister path. $ modprobe dummy numdummies=10000 $ ip link set dev dummy* up $ time rmmod dummy Without the patch With the patch real 0m 24.63s real 0m 5.15s user 0m 0.00s user 0m 0.00s sys 0m 6.05s sys 0m 5.14s Signed-off-by: Octavian Purdila <opurdila@ixiacom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-12-16net: Add batman-adv meshing protocolSven Eckelmann
B.A.T.M.A.N. (better approach to mobile ad-hoc networking) is a routing protocol for multi-hop ad-hoc mesh networks. The networks may be wired or wireless. See http://www.open-mesh.org/ for more information and user space tools. Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-12-16net: use NUMA_NO_NODE instead of the magic number -1Changli Gao
Signed-off-by: Changli Gao <xiaosuo@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-12-16bnx2x: Take the distribution range definition out of skb_tx_hash()Vladislav Zolotarov
Move the calcualation of the Tx hash for a given hash range into a separate function and define the skb_tx_hash(), which calculates a Tx hash for a [0; dev->real_num_tx_queues - 1] hash values range, using this function (__skb_tx_hash()). Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com> Signed-off-by: Eilon Greenstein <eilong@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-12-16ipv6: delete expired route in ip6_pmtu_deliverAndrey Vagin
The first big packets sent to a "low-MTU" client correctly triggers the creation of a temporary route containing the reduced MTU. But after the temporary route has expired, new ICMP6 "packet too big" will be sent, rt6_pmtu_discovery will find the previous EXPIRED route check that its mtu isn't bigger then in icmp packet and do nothing before the temporary route will not deleted by gc. I make the simple experiment: while :; do time ( dd if=/dev/zero bs=10K count=1 | ssh hostname dd of=/dev/null ) || break; done The "time" reports real 0m0.197s if a temporary route isn't expired, but it reports real 0m52.837s (!!!!) immediately after a temporare route has expired. Signed-off-by: Andrey Vagin <avagin@openvz.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-12-16cfg80211: fix null pointer dereference with a custom regulatory requestLuis R. Rodriguez
Once we moved the core regulatory request to the queue and let the scheduler process it last_request will have been left NULL until the schedular decides to process the first request. When this happens and we are loading a driver with a custom regulatory request like all Atheros drivers we end up with a NULL pointer dereference. We fix this by checking if the request was a custom one. BUG: unable to handle kernel NULL pointer dereference at 0000000000000004 IP: [<ffffffffa016de87>] freq_reg_info_regd.clone.2+0x27/0x130 [cfg80211] PGD 71f91067 PUD 712b2067 PMD 0 Oops: 0000 [#1] PREEMPT SMP last sysfs file: /sys/devices/pci0000:00/0000:00:1d.7/usb2/2-1/firmware/2-1/loading CPU 0 Modules linked in: ath9k_htc(+) ath9k_common ath9k_hw ath <etc> Pid: 3094, comm: insmod Tainted: G W 2.6.37-rc5-wl #16 INVALID/28427ZQ RIP: 0010:[<ffffffffa016de87>] [<ffffffffa016de87>] freq_reg_info_regd.clone.2+0x27/0x130 [cfg80211] RSP: 0018:ffff88007045db78 EFLAGS: 00010282 RAX: 0000000000000000 RBX: ffffffffa047d9a0 RCX: ffff88007045dbd0 RDX: 0000000000004e20 RSI: 000000000024cde0 RDI: ffff8800700483e0 RBP: ffff88007045db98 R08: ffffffffa02f5b40 R09: 0000000000000001 R10: 000000000000000e R11: 0000000000000001 R12: 0000000000000000 R13: ffff88007004e3b0 R14: 0000000000000000 R15: ffff880070048340 FS: 00007f635a707700(0000) GS:ffff880077400000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b CR2: 0000000000000004 CR3: 00000000708a9000 CR4: 00000000000006f0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400 Process insmod (pid: 3094, threadinfo ffff88007045c000, task ffff8800713e3ec0) Stack: ffffffffa047d9a0 0000000000000000 ffff88007004e3b0 0000000000000000 ffff88007045dc08 ffffffffa016e147 000000007045dc08 0000000000000002 ffff8800700483e0 ffffffffa02f5b40 ffff88007045dbd8 0000000000000000 Call Trace: [<ffffffffa016e147>] wiphy_apply_custom_regulatory+0x137/0x1d0 [cfg80211] [<ffffffffa047a690>] ? ath9k_reg_notifier+0x0/0x50 [ath9k_htc] [<ffffffffa02f47f7>] ath_regd_init+0x347/0x430 [ath] [<ffffffffa047b1f5>] ath9k_htc_probe_device+0x6c5/0x960 [ath9k_htc] [<ffffffffa0472a2c>] ath9k_htc_hw_init+0xc/0x30 [ath9k_htc] [<ffffffffa04747e6>] ath9k_hif_usb_probe+0x216/0x3b0 [ath9k_htc] [<ffffffffa03bb6bc>] usb_probe_interface+0x10c/0x210 [usbcore] [<ffffffff812aec26>] driver_probe_device+0x96/0x1c0 [<ffffffff812aedf3>] __driver_attach+0xa3/0xb0 [<ffffffff812aed50>] ? __driver_attach+0x0/0xb0 [<ffffffff812adaae>] bus_for_each_dev+0x5e/0x90 [<ffffffff812ae8c9>] driver_attach+0x19/0x20 [<ffffffff812ae438>] bus_add_driver+0x168/0x320 [<ffffffff812af071>] driver_register+0x71/0x140 [<ffffffff811fc4a8>] ? __raw_spin_lock_init+0x38/0x70 [<ffffffffa03ba39c>] usb_register_driver+0xdc/0x190 [usbcore] [<ffffffffa03a2000>] ? ath9k_htc_init+0x0/0x4f [ath9k_htc] [<ffffffffa047499e>] ath9k_hif_usb_init+0x1e/0x20 [ath9k_htc] [<ffffffffa03a202b>] ath9k_htc_init+0x2b/0x4f [ath9k_htc] [<ffffffff8100212f>] do_one_initcall+0x3f/0x180 [<ffffffff8109ef5b>] sys_init_module+0xbb/0x200 [<ffffffff8100bf52>] system_call_fastpath+0x16/0x1b Code: <etc, who cares> RIP [<ffffffffa016de87>] freq_reg_info_regd.clone.2+0x27/0x130 [cfg80211] RSP <ffff88007045db78> CR2: 0000000000000004 ---[ end trace 79e4193601c8b713 ]--- Reported-by: Sujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-16nl80211: Add notification for dropped Deauth/DisassocJouni Malinen
Add a new notification to indicate that a received, unprotected Deauthentication or Disassociation frame was dropped due to management frame protection being in use. This notification is needed to allow user space (e.g., wpa_supplicant) to implement SA Query procedure to recover from association state mismatch between an AP and STA. This is needed to avoid getting stuck in non-working state when MFP (IEEE 802.11w) is used and a protected Deauthentication or Disassociation frame is dropped for any reason. After that, the station would silently discard any unprotected Deauthentication or Disassociation frame that could be indicating that the AP does not have association for the STA (when the Reason Code would be 6 or 7). IEEE Std 802.11w-2009, 11.13 describes this recovery mechanism. Signed-off-by: Jouni Malinen <j@w1.fi> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-15wireless:mac80211: kill unuse macro MESH_CFG_CMP_LEN in mesh.hShan Wei
Commit 00d3f14c has removed the references of this macro, but left it only. So remove this definition. commit 00d3f14cf9f12c21428121026a5e1d5f65926447 Author: Johannes Berg <johannes@sipsolutions.net> Date: Tue Feb 10 21:26:00 2009 +0100 mac80211: use cfg80211s BSS infrastructure Remove all the code from mac80211 to keep track of BSSes and use the cfg80211-provided code completely. Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-15mac80211: Add timeout to BA session start APISujith Manoharan
Allow drivers or rate control algorithms to specify BlockAck session timeout when initiating an ADDBA transaction. This is useful in cases where maintaining persistent BA sessions does not incur any overhead. The current timeout value of 5000 TUs is retained for all non ath9k/ath9k_htc drivers. Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com> Reviewed-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-15nl80211: advertise maximum remain-on-channel durationJohannes Berg
With the upcoming hardware offload implementation, some devices will have a different maximum duration for the remain-on-channel command. Advertise the maximum duration in mac80211, and make mac80211 set it. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-15Merge branch 'master' of ↵John W. Linville
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6 Conflicts: drivers/net/wireless/iwlwifi/iwl-1000.c drivers/net/wireless/iwlwifi/iwl-6000.c drivers/net/wireless/iwlwifi/iwl-core.h
2010-12-15Merge branch 'master' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
2010-12-14Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6Linus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (75 commits) pppoe.c: Fix kernel panic caused by __pppoe_xmit WAN: Fix a TX IRQ causing BUG() in PC300 and PCI200SYN drivers. bnx2x: Advance a version number to 1.60.01-0 bnx2x: Fixed a compilation warning bnx2x: LSO code was broken on BE platforms qlge: Fix deadlock when cancelling worker. net: fix skb_defer_rx_timestamp() cxgb4vf: Ingress Queue Entry Size needs to be 64 bytes phy: add the IC+ IP1001 driver atm: correct sysfs 'device' link creation and parent relationships MAINTAINERS: remove me from tulip SCTP: Fix SCTP_SET_PEER_PRIMARY_ADDR to accpet v4mapped address enic: Bug Fix: Pass napi reference to the isr that services receive queue ipv6: fix nl group when advertising a new link connector: add module alias net: Document the kernel_recvmsg() function r8169: Fix runtime power management hso: IP checksuming doesn't work on GE0301 option cards xfrm: Fix xfrm_state_migrate leak net: Convert netpoll blocking api in bonding driver to be a counter ...
2010-12-14net: Abstract default MTU metric calculation behind an accessor.David S. Miller
Like RTAX_ADVMSS, make the default calculation go through a dst_ops method rather than caching the computation in the routing cache entries. Now dst metrics are pretty much left as-is when new entries are created, thus optimizing metric sharing becomes a real possibility. Signed-off-by: David S. Miller <davem@davemloft.net>
2010-12-14Merge branch 'for-davem' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6
2010-12-13ceph: fix msgr_init error pathSage Weil
create_workqueue() returns NULL on failure. Signed-off-by: Sage Weil <sage@newdream.net>
2010-12-13net: Abstract default ADVMSS behind an accessor.David S. Miller
Make all RTAX_ADVMSS metric accesses go through a new helper function, dst_metric_advmss(). Leave the actual default metric as "zero" in the real metric slot, and compute the actual default value dynamically via a new dst_ops AF specific callback. For stacked IPSEC routes, we use the advmss of the path which preserves existing behavior. Unlike ipv4/ipv6, DecNET ties the advmss to the mtu and thus updates advmss on pmtu updates. This inconsistency in advmss handling results in more raw metric accesses than I wish we ended up with. Signed-off-by: David S. Miller <davem@davemloft.net>
2010-12-13mac80211: support IBSS RSN with SW cryptoJohannes Berg
When software crypto is used, mac80211 will support IBSS RSN, it doesn't depend on the driver in that case. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-13mac80211 default tx_last_beacon false (congestion)Tim Harvey
The 802.11 spec states that the STA that generated the last Beacon frame shall be the STA that response to a probe request. This is important for congestion reduction when a probe request is received - only 1 node in an adhoc BSS will transmit a response. While mac80211 drivers should provide the tx_last_beacon function to report if they transmitted the last beacon many do not. As an attempt to reduce probe response congestion default this to 0 such that a node not implementing this capability does not contribute to unnecessary congestion. In a modern medium sized office environment I see upwards of 100 probe requests per second received at a given node from various hardware/OS/drivers doing zeroconf 'active probing' as opposed to passively listening for beacons. With a modest 10-node adhoc network consisting of drivers that do not implement this tx_last_beacon feature, I have seen this result in the simultaneous xmit of probe responses accumulating to 500 probe responses per second because of collisions which brings the adhoc network to its knees as well as causes needless congestion. Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-13mac80211: support separate default keysJohannes Berg
Add support for split default keys (unicast and multicast) in mac80211. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-13cfg80211/nl80211: separate unicast/multicast default TX keysJohannes Berg
Allow userspace to specify that a given key is default only for unicast and/or multicast transmissions. Only WEP keys are for both, WPA/RSN keys set here are GTKs for multicast only. For more future flexibility, allow to specify all combiations. Wireless extensions can only set both so use nl80211; WEP keys (connect keys) must be set as default for both (but 802.1X WEP is still possible). Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-13mac80211: clean up RX key checksJohannes Berg
Using the default key for "any key set" isn't quite what we should do. It works, but with the upcoming changes it makes life unnecessarily complex, so do something better here and really check for "any key". Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-13cfg80211: update information elements in cached BSS structSven Neumann
When a cached BSS struct is updated because a new beacon was received, the code replaces the cached information elements by the IEs from the new beacon. However it did not update the pub.information_elements and pub.len_information_elements fields leaving them either pointing to the old beacon IEs or in an inconsistent state where the data is replaced by the new beacon IEs but len_information_elements still has its value from the first beacon. Fix this by updating the information elements fields if they are pointing to beacon IEs. Signed-off-by: Sven Neumann <s.neumann@raumfeld.com> Reviewed-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-13cfg80211: Add antenna availability informationBruno Randolf
Add a field to wiphy for the hardware to report the availble antennas for configuration. Only if this is set to something bigger than zero, will the anntenna configuration ops be executed. Allthough this could be a simple number of antennas, I defined it as a bitmap of antennas which are available for configuration, since it's more consistent with the rest of the antenna API and there could be cases where the hardware allows only configuration of certain antennas. As it does not make much of a difference in size or normal usage, I think it's better to be able to support this, in case the need arises. The antenna configuration is now also checked against the availabe antennas and rejected if it does not match. Signed-off-by: Bruno Randolf <br1@einfach.org> -- v3: always apply available antenna mask (for "all" antennas case). v2: reject antenna configurations which don't match the available antennas Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-12-13Merge branch 'master' of ↵John W. Linville
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6 into for-davem
2010-12-13net: add limits to ip_default_ttlEric Dumazet
ip_default_ttl should be between 1 and 255 Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-15 22:32:00 +0000