| Age | Commit message (Collapse) | Author |
|---|
|
The following warning was reported by syzbot on Oct 24. 2017:
KASAN: slab-out-of-bounds Read in tipc_nametbl_lookup_dst_nodes
This is a harmless bug, but we still want to get rid of the warning,
so we swap the two conditions in question.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In this commit, we make it possible to send connectionless unicast
messages to any member corresponding to the given member identity,
when there is more than one such member. The sender must use a
TIPC_ADDR_NAME address to achieve this effect.
We also perform load balancing between the destinations, i.e., we
primarily select one which has advertised sufficient send window
to not cause a block/EAGAIN delay, if any. This mechanism is
overlayed on the always present round-robin selection.
Anycast messages are subject to the same start synchronization
and flow control mechanism as group broadcast messages.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As a preparation for introducing flow control for multicast and datagram
messaging we need a more strictly defined framework than we have now. A
socket must be able keep track of exactly how many and which other
sockets it is allowed to communicate with at any moment, and keep the
necessary state for those.
We therefore introduce a new concept we have named Communication Group.
Sockets can join a group via a new setsockopt() call TIPC_GROUP_JOIN.
The call takes four parameters: 'type' serves as group identifier,
'instance' serves as an logical member identifier, and 'scope' indicates
the visibility of the group (node/cluster/zone). Finally, 'flags' makes
it possible to set certain properties for the member. For now, there is
only one flag, indicating if the creator of the socket wants to receive
a copy of broadcast or multicast messages it is sending via the socket,
and if wants to be eligible as destination for its own anycasts.
A group is closed, i.e., sockets which have not joined a group will
not be able to send messages to or receive messages from members of
the group, and vice versa.
Any member of a group can send multicast ('group broadcast') messages
to all group members, optionally including itself, using the primitive
send(). The messages are received via the recvmsg() primitive. A socket
can only be member of one group at a time.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We often see a need for a linked list of destination identities,
sometimes containing a port number, sometimes a node identity, and
sometimes both. The currently defined struct u32_list is not generic
enough to cover all cases, so we extend it to contain two u32 integers
and rename it to struct tipc_dest_list.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a new subscription object is inserted into name_seq->subscriptions
list, it's under name_seq->lock protection; when a subscription is
deleted from the list, it's also under the same lock protection;
similarly, when accessing a subscription by going through subscriptions
list, the entire process is also protected by the name_seq->lock.
Therefore, if subscription refcount is increased before it's inserted
into subscriptions list, and its refcount is decreased after it's
deleted from the list, it will be unnecessary to hold refcount at all
before accessing subscription object which is obtained by going through
subscriptions list under name_seq->lock protection.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As a further preparation for the upcoming 'replicast' functionality,
we add some necessary structs and functions for looking up and returning
a list of all nodes that host destinations for a given multicast message.
Reviewed-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During multicast reception we currently use a simple linked list with
push/pop semantics to store port numbers.
We now see a need for a more generic list for storing values of type
u32. We therefore make some modifications to this list, while replacing
the prefix 'tipc_plist_' with 'u32_'. We also add a couple of new
functions which will come to use in the next commits.
Acked-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make the c files less cluttered and enable netlink attributes to be
shared between files.
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Until now, struct tipc_subscriber has duplicate fields for
type, upper and lower (as member of struct tipc_name_seq) at:
1. as member seq in struct tipc_subscription
2. as member seq in struct tipc_subscr, which is contained
in struct tipc_event
The former structure contains the type, upper and lower
values in network byte order and the later contains the
intact copy of the request.
The struct tipc_subscription contains a field swap to
determine if request needs network byte order conversion.
Thus by using swap, we can convert the request when
required instead of duplicating it.
In this commit,
1. we remove the references to these elements as members of
struct tipc_subscription and replace them with elements
from struct tipc_subscr.
2. provide new functions to convert the user request into
network byte order.
Acked-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The file name_distr.c currently contains three functions,
named_cluster_distribute(), tipc_publ_subcscribe() and
tipc_publ_unsubscribe() that all directly access fields in
struct tipc_node. We want to eliminate such dependencies, so
we move those functions to the file node.c and rename them to
tipc_node_broadcast(), tipc_node_subscribe() and tipc_node_unsubscribe()
respectively.
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a topology server accepts a connection request from its client,
it allocates a connection instance and a tipc_subscriber structure
object. The former is used to communicate with client, and the latter
is often treated as a subscriber which manages all subscription events
requested from a same client. When a topology server receives a request
of subscribing name services from a client through the connection, it
creates a tipc_subscription structure instance which is seen as a
subscription recording what name services are subscribed. In order to
manage all subscriptions from a same client, topology server links
them into the subscrp_list of the subscriber. So subscriber and
subscription completely represents different meanings respectively,
but function names associated with them make us so confused that we
are unable to easily tell which function is against subscriber and
which is to subscription. So we want to eliminate the confusion by
renaming them.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
[ 28.531768] =============================================
[ 28.532322] [ INFO: possible recursive locking detected ]
[ 28.532322] 3.19.0+ #194 Not tainted
[ 28.532322] ---------------------------------------------
[ 28.532322] insmod/583 is trying to acquire lock:
[ 28.532322] (&(&nseq->lock)->rlock){+.....}, at: [<ffffffffa000d219>] tipc_nametbl_remove_publ+0x49/0x2e0 [tipc]
[ 28.532322]
[ 28.532322] but task is already holding lock:
[ 28.532322] (&(&nseq->lock)->rlock){+.....}, at: [<ffffffffa000e0dc>] tipc_nametbl_stop+0xfc/0x1f0 [tipc]
[ 28.532322]
[ 28.532322] other info that might help us debug this:
[ 28.532322] Possible unsafe locking scenario:
[ 28.532322]
[ 28.532322] CPU0
[ 28.532322] ----
[ 28.532322] lock(&(&nseq->lock)->rlock);
[ 28.532322] lock(&(&nseq->lock)->rlock);
[ 28.532322]
[ 28.532322] *** DEADLOCK ***
[ 28.532322]
[ 28.532322] May be due to missing lock nesting notation
[ 28.532322]
[ 28.532322] 3 locks held by insmod/583:
[ 28.532322] #0: (net_mutex){+.+.+.}, at: [<ffffffff8163e30f>] register_pernet_subsys+0x1f/0x50
[ 28.532322] #1: (&(&tn->nametbl_lock)->rlock){+.....}, at: [<ffffffffa000e091>] tipc_nametbl_stop+0xb1/0x1f0 [tipc]
[ 28.532322] #2: (&(&nseq->lock)->rlock){+.....}, at: [<ffffffffa000e0dc>] tipc_nametbl_stop+0xfc/0x1f0 [tipc]
[ 28.532322]
[ 28.532322] stack backtrace:
[ 28.532322] CPU: 1 PID: 583 Comm: insmod Not tainted 3.19.0+ #194
[ 28.532322] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2007
[ 28.532322] ffffffff82394460 ffff8800144cb928 ffffffff81792f3e 0000000000000007
[ 28.532322] ffffffff82394460 ffff8800144cba28 ffffffff810a8080 ffff8800144cb998
[ 28.532322] ffffffff810a4df3 ffff880013e9cb10 ffffffff82b0d330 ffff880013e9cb38
[ 28.532322] Call Trace:
[ 28.532322] [<ffffffff81792f3e>] dump_stack+0x4c/0x65
[ 28.532322] [<ffffffff810a8080>] __lock_acquire+0x740/0x1ca0
[ 28.532322] [<ffffffff810a4df3>] ? __bfs+0x23/0x270
[ 28.532322] [<ffffffff810a7506>] ? check_irq_usage+0x96/0xe0
[ 28.532322] [<ffffffff810a8a73>] ? __lock_acquire+0x1133/0x1ca0
[ 28.532322] [<ffffffffa000d219>] ? tipc_nametbl_remove_publ+0x49/0x2e0 [tipc]
[ 28.532322] [<ffffffff810a9c0c>] lock_acquire+0x9c/0x140
[ 28.532322] [<ffffffffa000d219>] ? tipc_nametbl_remove_publ+0x49/0x2e0 [tipc]
[ 28.532322] [<ffffffff8179c41f>] _raw_spin_lock_bh+0x3f/0x50
[ 28.532322] [<ffffffffa000d219>] ? tipc_nametbl_remove_publ+0x49/0x2e0 [tipc]
[ 28.532322] [<ffffffffa000d219>] tipc_nametbl_remove_publ+0x49/0x2e0 [tipc]
[ 28.532322] [<ffffffffa000e11e>] tipc_nametbl_stop+0x13e/0x1f0 [tipc]
[ 28.532322] [<ffffffffa000dfe5>] ? tipc_nametbl_stop+0x5/0x1f0 [tipc]
[ 28.532322] [<ffffffffa0004bab>] tipc_init_net+0x13b/0x150 [tipc]
[ 28.532322] [<ffffffffa0004a75>] ? tipc_init_net+0x5/0x150 [tipc]
[ 28.532322] [<ffffffff8163dece>] ops_init+0x4e/0x150
[ 28.532322] [<ffffffff810aa66d>] ? trace_hardirqs_on+0xd/0x10
[ 28.532322] [<ffffffff8163e1d3>] register_pernet_operations+0xf3/0x190
[ 28.532322] [<ffffffff8163e31e>] register_pernet_subsys+0x2e/0x50
[ 28.532322] [<ffffffffa002406a>] tipc_init+0x6a/0x1000 [tipc]
[ 28.532322] [<ffffffffa0024000>] ? 0xffffffffa0024000
[ 28.532322] [<ffffffff810002d9>] do_one_initcall+0x89/0x1c0
[ 28.532322] [<ffffffff811b7cb0>] ? kmem_cache_alloc_trace+0x50/0x1b0
[ 28.532322] [<ffffffff810e725b>] ? do_init_module+0x2b/0x200
[ 28.532322] [<ffffffff810e7294>] do_init_module+0x64/0x200
[ 28.532322] [<ffffffff810e9353>] load_module+0x12f3/0x18e0
[ 28.532322] [<ffffffff810e5890>] ? show_initstate+0x50/0x50
[ 28.532322] [<ffffffff810e9a19>] SyS_init_module+0xd9/0x110
[ 28.532322] [<ffffffff8179f3b3>] sysenter_dispatch+0x7/0x1f
Before tipc_purge_publications() calls tipc_nametbl_remove_publ() to
remove a publication with a name sequence, the name sequence's lock
is held. However, when tipc_nametbl_remove_publ() calling
tipc_nameseq_remove_publ() to remove the publication, it first tries
to query name sequence instance with the publication, and then holds
the lock of the found name sequence. But as the lock may be already
taken in tipc_purge_publications(), deadlock happens like above
scenario demonstrated. As tipc_nameseq_remove_publ() doesn't grab name
sequence's lock, the deadlock can be avoided if it's directly invoked
by tipc_purge_publications().
Fixes: 97ede29e80ee ("tipc: convert name table read-write lock to RCU")
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add TIPC_CMD_NOOP to compat layer and remove the old framework.
All legacy nl commands are now converted to the compat layer in
netlink_compat.c.
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add functionality for printing a dump header and convert
TIPC_CMD_SHOW_NAME_TABLE to compat dumpit.
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The new netlink API is no longer "v2" but rather the standard API and
the legacy API is now "nl compat". We split them into separate
start/stop and put them in different files in order to further
distinguish them.
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The structure 'tipc_port_list' is used to collect port numbers
representing multicast destination socket on a receiving node.
The list is not based on a standard linked list, and is in reality
optimized for the uncommon case that there are more than one
multicast destinations per node. This makes the list handling
unecessarily complex, and as a consequence, even the socket
multicast reception becomes more complex.
In this commit, we replace 'tipc_port_list' with a new 'struct
tipc_plist', which is based on a standard list. We give the new
list stack (push/pop) semantics, someting that simplifies
the implementation of the function tipc_sk_mcast_rcv().
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If net namespace is supported in tipc, each namespace will be treated
as a separate tipc node. Therefore, every namespace must own its
private tipc node address. This means the "tipc_own_addr" global
variable of node address must be moved to tipc_net structure to
satisfy the requirement. It's turned out that users also can assign
node address for every namespace.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Tested-by: Tero Aho <Tero.Aho@coriant.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
TIPC name table is used to store the mapping relationship between
TIPC service name and socket port ID. When tipc supports namespace,
it allows users to publish service names only owned by a certain
namespace. Therefore, every namespace must have its private name
table to prevent service names published to one namespace from being
contaminated by other service names in another namespace. Therefore,
The name table global variable (ie, nametbl) and its lock must be
moved to tipc_net structure, and a parameter of namespace must be
added for necessary functions so that they can obtain name table
variable defined in tipc_net structure.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Tested-by: Tero Aho <Tero.Aho@coriant.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
TIPC broadcast link is statically established and its relevant states
are maintained with the global variables: "bcbearer", "bclink" and
"bcl". Allowing different namespace to own different broadcast link
instances, these variables must be moved to tipc_net structure and
broadcast link instances would be allocated and initialized when
namespace is created.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Tested-by: Tero Aho <Tero.Aho@coriant.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Global variables associated with node table are below:
- node table list (node_htable)
- node hash table list (tipc_node_list)
- node table lock (node_list_lock)
- node number counter (tipc_num_nodes)
- node link number counter (tipc_num_links)
To make node table support namespace, above global variables must be
moved to tipc_net structure in order to keep secret for different
namespaces. As a consequence, these variables are allocated and
initialized when namespace is created, and deallocated when namespace
is destroyed. After the change, functions associated with these
variables have to utilize a namespace pointer to access them. So
adding namespace pointer as a parameter of these functions is the
major change made in the commit.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Tested-by: Tero Aho <Tero.Aho@coriant.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The commit fb9962f3cefe ("tipc: ensure all name sequences are properly
protected with its lock") involves below errors:
net/tipc/name_table.c:980 tipc_purge_publications() error: double lock 'spin_lock:&seq->lock'
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Convert tipc name table read-write lock to RCU. After this change,
a new spin lock is used to protect name table on write side while
RCU is applied on read side.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Tested-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a list_head variable is seen as a new entry to be added to a
list head, it's unnecessary to be initialized with INIT_LIST_HEAD().
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Tested-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When tipc name sequence is published, name table lock is released
before name sequence buffer is delivered to remote nodes through its
underlying unicast links. However, when name sequence is withdrawn,
the name table lock is held until the transmission of the removal
message of name sequence is finished. During the process, node lock
is nested in name table lock. To prevent node lock from being nested
in name table lock, while withdrawing name, we should adopt the same
locking policy of publishing name sequence: name table lock should
be released before message is sent.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Tested-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As tipc_nametbl_lock is used to protect name_table structure, the lock
must be held while all members of name_table structure are accessed.
However, the lock is not obtained while a member of name_table
structure - local_publ_count is read in tipc_nametbl_publish(), as
a consequence, an inconsistent value of local_publ_count might be got.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Tested-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
TIPC internally created a name table which is used to store name
sequences. Now there is a read-write lock - tipc_nametbl_lock to
protect the table, and each name sequence saved in the table is
protected with its private lock. When a name sequence is inserted
or removed to or from the table, its members might need to change.
Therefore, in normal case, the two locks must be held while TIPC
operates the table. However, there are still several places where
we only hold tipc_nametbl_lock without proprerly obtaining name
sequence lock, which might cause the corruption of name sequence.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Tested-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As TIPC subscriber server is terminated before name table, no user
depends on subscription list of name sequence when name table is
stopped. Therefore, all name sequences stored in name table should
be released whatever their subscriptions lists are empty or not,
otherwise, memory leak might happen.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Tested-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Name table locking policy is going to be adjusted from read-write
lock protection to RCU lock protection in the future commits. But
its essential precondition is to convert the allocation way of name
table from static to dynamic mode.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Tested-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The node subscribe infrastructure represents a virtual base class, so
its users, such as struct tipc_port and struct publication, can derive
its implemented functionalities. However, after the removal of struct
tipc_port, struct publication is left as its only single user now. So
defining an abstract infrastructure for one user becomes no longer
reasonable. If corresponding new functions associated with the
infrastructure are moved to name_table.c file, the node subscription
infrastructure can be removed as well.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix sparse warnings about non-static declaration of static functions
in the new tipc netlink API.
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add TIPC_NL_NAME_TABLE_GET command to the new tipc netlink API.
This command supports dumping the name table of all nodes.
Netlink logical layout of name table response message:
-> name table
-> publication
-> type
-> lower
-> upper
-> scope
-> node
-> ref
-> key
Signed-off-by: Richard Alpe <richard.alpe@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
TIPC name table updates are distributed asynchronously in a cluster,
entailing a risk of certain race conditions. E.g., if two nodes
simultaneously issue conflicting (overlapping) publications, this may
not be detected until both publications have reached a third node, in
which case one of the publications will be silently dropped on that
node. Hence, we end up with an inconsistent name table.
In most cases this conflict is just a temporary race, e.g., one
node is issuing a publication under the assumption that a previous,
conflicting, publication has already been withdrawn by the other node.
However, because of the (rtt related) distributed update delay, this
may not yet hold true on all nodes. The symptom of this failure is a
syslog message: "tipc: Cannot publish {%u,%u,%u}, overlap error".
In this commit we add a resiliency queue at the receiving end of
the name table distributor. When insertion of an arriving publication
fails, we retain it in this queue for a short amount of time, assuming
that another update will arrive very soon and clear the conflict. If so
happens, we insert the publication, otherwise we drop it.
The (configurable) retention value defaults to 2000 ms. Knowing from
experience that the situation described above is extremely rare, there
is no risk that the queue will accumulate any large number of items.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We move the inline functions in the file port.h to socket.c, and modify
their names accordingly.
We move struct tipc_port and some macros to socket.h.
Finally, we remove the file port.h.
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 1bb8dce57f4d15233688c68990852a10eb1cd79f ("tipc: fix memory
leak during module removal") introduced a memory leak issue: when
name table is stopped, it's forgotten that publication instances are
freed properly. Additionally the useless "continue" statement in
tipc_nametbl_stop() is removed as well.
Reported-by: Jason <huzhijiang@gmail.com>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Acked-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit a89778d8baf19cd7e728d81121a294a06cedaad1 ("tipc: add support
for link state subscriptions") introduced below possible deadlock
scenario:
CPU0 CPU1
T0: tipc_publish() link_timeout()
T1: tipc_nametbl_publish() [grab node lock]*
T2: [grab nametbl write lock]* link_state_event()
T3: named_cluster_distribute() link_activate()
T4: [grab node lock]* tipc_node_link_up()
T5: tipc_nametbl_publish()
T6: [grab nametble write lock]*
The opposite order of holding nametbl write lock and node lock on
above two different paths may result in a deadlock. If we move the
the delivery of named messages via link out of name nametbl lock,
the reverse order of holding locks will be eliminated, as a result,
the deadlock will be killed as well.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the TIPC module is removed, the tasklet handler is disabled
before all other subsystems. This will cause lingering publications
in the name table because the node_down tasklets responsible to
clean up publications from an unreachable node will never run.
When the name table is shut down, these publications are detected
and an error message is logged:
tipc: nametbl_stop(): orphaned hash chain detected
This is actually a memory leak, introduced with commit
993b858e37b3120ee76d9957a901cca22312ffaa ("tipc: correct the order
of stopping services at rmmod")
Instead of just logging an error and leaking memory, we free
the orphaned entries during nametable shutdown.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When tipc module is inserted, many tipc components are initialized
one by one. During the initialization period, if one of them is
failed, tipc_core_stop() will be called to stop all components
whatever corresponding components are created or not. To avoid to
release uncreated ones, relevant components have to add necessary
enabled flags indicating whether they are created or not.
But in the initialization stage, if one component is unsuccessfully
created, we will just destroy successfully created components before
the failed component instead of all components. All enabled flags
defined in components, in turn, become redundant. Additionally it's
also unnecessary to identify whether table.types is NULL in
tipc_nametbl_stop() because name stable has been definitely created
successfully when tipc_nametbl_stop() is called.
Cc: Jon Maloy <jon.maloy@ericsson.com>
Cc: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Reviewed-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We remove a number of unnecessary variables and branches
in TIPC. This patch is cosmetic and does not change the
operation of TIPC in any way.
Reviewed-by: Jon Maloy <jon.maloy@ericsson.com>
Reviewed-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: Wang Weidong <wangweidong1@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
No runtime code changes here. Just a realign of the function
arguments to start where the 1st one was, and fit as many args
as can be put in an 80 char line.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I'm not sure why, but the hlist for each entry iterators were conceived
list_for_each_entry(pos, head, member)
The hlist ones were greedy and wanted an extra parameter:
hlist_for_each_entry(tpos, pos, head, member)
Why did they need an extra pos parameter? I'm not quite sure. Not only
they don't really need it, it also prevents the iterator from looking
exactly like the list iterator, which is unfortunate.
Besides the semantic patch, there was some manual work required:
- Fix up the actual hlist iterators in linux/list.h
- Fix up the declaration of other iterators based on the hlist ones.
- A very small amount of places were using the 'node' parameter, this
was modified to use 'obj->member' instead.
- Coccinelle didn't handle the hlist_for_each_entry_safe iterator
properly, so those had to be fixed up manually.
The semantic patch which is mostly the work of Peter Senna Tschudin is here:
@@
iterator name hlist_for_each_entry, hlist_for_each_entry_continue, hlist_for_each_entry_from, hlist_for_each_entry_rcu, hlist_for_each_entry_rcu_bh, hlist_for_each_entry_continue_rcu_bh, for_each_busy_worker, ax25_uid_for_each, ax25_for_each, inet_bind_bucket_for_each, sctp_for_each_hentry, sk_for_each, sk_for_each_rcu, sk_for_each_from, sk_for_each_safe, sk_for_each_bound, hlist_for_each_entry_safe, hlist_for_each_entry_continue_rcu, nr_neigh_for_each, nr_neigh_for_each_safe, nr_node_for_each, nr_node_for_each_safe, for_each_gfn_indirect_valid_sp, for_each_gfn_sp, for_each_host;
type T;
expression a,c,d,e;
identifier b;
statement S;
@@
-T b;
<+... when != b
(
hlist_for_each_entry(a,
- b,
c, d) S
|
hlist_for_each_entry_continue(a,
- b,
c) S
|
hlist_for_each_entry_from(a,
- b,
c) S
|
hlist_for_each_entry_rcu(a,
- b,
c, d) S
|
hlist_for_each_entry_rcu_bh(a,
- b,
c, d) S
|
hlist_for_each_entry_continue_rcu_bh(a,
- b,
c) S
|
for_each_busy_worker(a, c,
- b,
d) S
|
ax25_uid_for_each(a,
- b,
c) S
|
ax25_for_each(a,
- b,
c) S
|
inet_bind_bucket_for_each(a,
- b,
c) S
|
sctp_for_each_hentry(a,
- b,
c) S
|
sk_for_each(a,
- b,
c) S
|
sk_for_each_rcu(a,
- b,
c) S
|
sk_for_each_from
-(a, b)
+(a)
S
+ sk_for_each_from(a) S
|
sk_for_each_safe(a,
- b,
c, d) S
|
sk_for_each_bound(a,
- b,
c) S
|
hlist_for_each_entry_safe(a,
- b,
c, d, e) S
|
hlist_for_each_entry_continue_rcu(a,
- b,
c) S
|
nr_neigh_for_each(a,
- b,
c) S
|
nr_neigh_for_each_safe(a,
- b,
c, d) S
|
nr_node_for_each(a,
- b,
c) S
|
nr_node_for_each_safe(a,
- b,
c, d) S
|
- for_each_gfn_sp(a, c, d, b) S
+ for_each_gfn_sp(a, c, d) S
|
- for_each_gfn_indirect_valid_sp(a, c, d, b) S
+ for_each_gfn_indirect_valid_sp(a, c, d) S
|
for_each_host(a,
- b,
c) S
|
for_each_host_safe(a,
- b,
c, d) S
|
for_each_mesh_entry(a,
- b,
c, d) S
)
...+>
[akpm@linux-foundation.org: drop bogus change from net/ipv4/raw.c]
[akpm@linux-foundation.org: drop bogus hunk from net/ipv6/raw.c]
[akpm@linux-foundation.org: checkpatch fixes]
[akpm@linux-foundation.org: fix warnings]
[akpm@linux-foudnation.org: redo intrusive kvm changes]
Tested-by: Peter Senna Tschudin <peter.senna@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Found by http://coccinelle.lip6.fr/
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Gets rid of the need for users to specify the maximum number of
name publications supported by TIPC. TIPC now automatically provides
support for the maximum number of name publications to 65535.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is nothing changing this variable dynamically, so change
it to a macro to make that more obvious when reading the code.
Signed-off-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The tipc_printf is renamed to tipc_snprintf, as the new name
describes more what the function actually does. It is also
changed to take a buffer and length parameter and return
number of characters written to the buffer. All callers of
this function that used to pass a print_buf are updated.
Final removal of the struct print_buf itself will be done
synchronously with the pending removal of the deprecated
logging code that also was using it.
Functions that build up a response message with a list of
ports, nametable contents etc. are changed to return the number
of characters written to the output buffer. This information
was previously hidden in a field of the print_buf struct, and
the number of chars written was fetched with a call to
tipc_printbuf_validate. This function is removed since it
is no longer referenced nor needed.
A generic max size ULTRA_STRING_MAX_LEN is defined, named
in keeping with the existing TIPC_TLV_ULTRA_STRING, and the
various definitions in port, link and nametable code that
largely duplicated this information are removed. This means
that amount of link statistics that can be returned is now
increased from 2k to 32k.
The buffer overflow check is now done just before the reply
message is passed over netlink or TIPC to a remote node and
the message indicating a truncated buffer is changed to a less
dramatic one (less CAPS), placed at the end of the message.
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
All messages should go directly to the kernel log. The TIPC
specific error, warning, info and debug trace macro's are
removed and all references replaced with pr_err, pr_warn,
pr_info and pr_debug.
Commonly used sub-strings are explicitly declared as a const
char to reduce .text size.
Note that this means the debug messages (changed to pr_debug),
are now enabled through dynamic debugging, instead of a TIPC
specific Kconfig option (TIPC_DEBUG). The latter will be
phased out completely
Signed-off-by: Erik Hugne <erik.hugne@ericsson.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
[PG: use pr_fmt as suggested by Joe Perches <joe@perches.com>]
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
With the default name table size of 1024, it is possible that
the sanity check in tipc_nametbl_stop could spam out 1024
essentially identical error messages if memory was corrupted
or similar. Limit it to issuing no more than a single message.
The actual chain number (i.e. 0 --> 1023) wouldn't provide any
useful insight if/when such an instance happened, so don't
bother printing out that value.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Fix incorrect start markers, wrapped summary lines, missing section
breaks, incorrect separators, and some name mismatches.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some of the comment blocks are floating in limbo between two
functions, or between blocks of code. Delete the extra line
feeds between any comment and its associated following block
of code, to be consistent with the majority of the rest of
the kernel. Also delete trailing newlines at EOF and fix
a couple trivial typos in existing comments.
This is a 100% cosmetic change with no runtime impact. We get
rid of over 500 lines of non-code, and being blank line deletes,
they won't even show up as noise in git blame.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Consolidates validation of scope and name sequence range values into
a single routine where it applies both to local name publications
and to name publications issued by other nodes in the network. This
change means that the scope value for non-local publications is now
validated and the name sequence range for local publications is now
validated only once. Additionally, a publication attempt that fails
validation now creates an entry in the system log file only if debugging
capabilities have been enabled; this prevents the system log from being
cluttered up with messages caused by a defective application or network
node.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
Replaces two identical chunks of code that delete an unused name
sequence structure from TIPC's name table with calls to a new routine
that performs this operation.
This change is cosmetic and doesn't impact the operation of TIPC.
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
