| Age | Commit message (Collapse) | Author |
|---|
|
For some chips/drivers, e.g., QCA6174 with ath10k, the decryption is
done by the hardware, and the Protected bit in the Frame Control field
is cleared in the lower level driver before the frame is passed to
mac80211. In such cases, the condition for ieee80211_has_protected() is
not met in ieee80211_rx_h_defragment() of mac80211 and the new security
validation steps are not executed.
Extend mac80211 to cover the case where the Protected bit has been
cleared, but the frame is indicated as having been decrypted by the
hardware. This extends protection against mixed key and fragment cache
attack for additional drivers/chips. This fixes CVE-2020-24586 and
CVE-2020-24587 for such cases.
Tested-on: QCA6174 hw3.2 PCI WLAN.RM.4.4.1-00110-QCARMSWP-1
Cc: stable@vger.kernel.org
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Link: https://lore.kernel.org/r/20210511200110.037aa5ca0390.I7bb888e2965a0db02a67075fcb5deb50eb7408aa@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
EAPOL frames are used for authentication and key management between the
AP and each individual STA associated in the BSS. Those frames are not
supposed to be sent by one associated STA to another associated STA
(either unicast for broadcast/multicast).
Similarly, in 802.11 they're supposed to be sent to the authenticator
(AP) address.
Since it is possible for unexpected EAPOL frames to result in misbehavior
in supplicant implementations, it is better for the AP to not allow such
cases to be forwarded to other clients either directly, or indirectly if
the AP interface is part of a bridge.
Accept EAPOL (control port) frames only if they're transmitted to the
own address, or, due to interoperability concerns, to the PAE group
address.
Disable forwarding of EAPOL (or well, the configured control port
protocol) frames back to wireless medium in all cases. Previously, these
frames were accepted from fully authenticated and authorized stations
and also from unauthenticated stations for one of the cases.
Additionally, to avoid forwarding by the bridge, rewrite the PAE group
address case to the local MAC address.
Cc: stable@vger.kernel.org
Co-developed-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Link: https://lore.kernel.org/r/20210511200110.cb327ed0cabe.Ib7dcffa2a31f0913d660de65ba3c8aca75b1d10f@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Similar to the issues fixed in previous patches, TKIP and WEP
should be protected even if for TKIP we have the Michael MIC
protecting it, and WEP is broken anyway.
However, this also somewhat protects potential other algorithms
that drivers might implement.
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210511200110.430e8c202313.Ia37e4e5b6b3eaab1a5ae050e015f6c92859dbe27@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
As pointed out by Mathy Vanhoef, we implement the RX PN check
on fragmented frames incorrectly - we check against the last
received PN prior to the new frame, rather than to the one in
this frame itself.
Prior patches addressed the security issue here, but in order
to be able to reason better about the code, fix it to really
compare against the current frame's PN, not the last stored
one.
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210511200110.bfbc340ff071.Id0b690e581da7d03d76df90bb0e3fd55930bc8a0@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Prior patches protected against fragmentation cache attacks
by coloring keys, but this shows that it can lead to issues
when multiple stations use the same sequence number. Add a
fragment cache to struct sta_info (in addition to the one in
the interface) to separate fragments for different stations
properly.
This then automatically clear most of the fragment cache when a
station disconnects (or reassociates) from an AP, or when client
interfaces disconnect from the network, etc.
On the way, also fix the comment there since this brings us in line
with the recommendation in 802.11-2016 ("An AP should support ...").
Additionally, remove a useless condition (since there's no problem
purging an already empty list).
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210511200110.fc35046b0d52.I1ef101e3784d13e8f6600d83de7ec9a3a45bcd52@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
With old ciphers (WEP and TKIP) we shouldn't be using A-MSDUs
since A-MSDUs are only supported if we know that they are, and
the only practical way for that is HT support which doesn't
support old ciphers.
However, we would normally accept them anyway. Since we check
the MMIC before deaggregating A-MSDUs, and the A-MSDU bit in
the QoS header is not protected in TKIP (or WEP), this enables
attacks similar to CVE-2020-24588. To prevent that, drop A-MSDUs
completely with old ciphers.
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20210511200110.076543300172.I548e6e71f1ee9cad4b9a37bf212ae7db723587aa@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Properly parse A-MSDUs whose first 6 bytes happen to equal a rfc1042
header. This can occur in practice when the destination MAC address
equals AA:AA:03:00:00:00. More importantly, this simplifies the next
patch to mitigate A-MSDU injection attacks.
Cc: stable@vger.kernel.org
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@kuleuven.be>
Link: https://lore.kernel.org/r/20210511200110.0b2b886492f0.I23dd5d685fe16d3b0ec8106e8f01b59f499dffed@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Simultaneously prevent mixed key attacks (CVE-2020-24587) and fragment
cache attacks (CVE-2020-24586). This is accomplished by assigning a
unique color to every key (per interface) and using this to track which
key was used to decrypt a fragment. When reassembling frames, it is
now checked whether all fragments were decrypted using the same key.
To assure that fragment cache attacks are also prevented, the ID that is
assigned to keys is unique even over (re)associations and (re)connects.
This means fragments separated by a (re)association or (re)connect will
not be reassembled. Because mac80211 now also prevents the reassembly of
mixed encrypted and plaintext fragments, all cache attacks are prevented.
Cc: stable@vger.kernel.org
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@kuleuven.be>
Link: https://lore.kernel.org/r/20210511200110.3f8290e59823.I622a67769ed39257327a362cfc09c812320eb979@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Do not mix plaintext and encrypted fragments in protected Wi-Fi
networks. This fixes CVE-2020-26147.
Previously, an attacker was able to first forward a legitimate encrypted
fragment towards a victim, followed by a plaintext fragment. The
encrypted and plaintext fragment would then be reassembled. For further
details see Section 6.3 and Appendix D in the paper "Fragment and Forge:
Breaking Wi-Fi Through Frame Aggregation and Fragmentation".
Because of this change there are now two equivalent conditions in the
code to determine if a received fragment requires sequential PNs, so we
also move this test to a separate function to make the code easier to
maintain.
Cc: stable@vger.kernel.org
Signed-off-by: Mathy Vanhoef <Mathy.Vanhoef@kuleuven.be>
Link: https://lore.kernel.org/r/20210511200110.30c4394bb835.I5acfdb552cc1d20c339c262315950b3eac491397@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core:
- bpf:
- allow bpf programs calling kernel functions (initially to
reuse TCP congestion control implementations)
- enable task local storage for tracing programs - remove the
need to store per-task state in hash maps, and allow tracing
programs access to task local storage previously added for
BPF_LSM
- add bpf_for_each_map_elem() helper, allowing programs to walk
all map elements in a more robust and easier to verify fashion
- sockmap: support UDP and cross-protocol BPF_SK_SKB_VERDICT
redirection
- lpm: add support for batched ops in LPM trie
- add BTF_KIND_FLOAT support - mostly to allow use of BTF on
s390 which has floats in its headers files
- improve BPF syscall documentation and extend the use of kdoc
parsing scripts we already employ for bpf-helpers
- libbpf, bpftool: support static linking of BPF ELF files
- improve support for encapsulation of L2 packets
- xdp: restructure redirect actions to avoid a runtime lookup,
improving performance by 4-8% in microbenchmarks
- xsk: build skb by page (aka generic zerocopy xmit) - improve
performance of software AF_XDP path by 33% for devices which don't
need headers in the linear skb part (e.g. virtio)
- nexthop: resilient next-hop groups - improve path stability on
next-hops group changes (incl. offload for mlxsw)
- ipv6: segment routing: add support for IPv4 decapsulation
- icmp: add support for RFC 8335 extended PROBE messages
- inet: use bigger hash table for IP ID generation
- tcp: deal better with delayed TX completions - make sure we don't
give up on fast TCP retransmissions only because driver is slow in
reporting that it completed transmitting the original
- tcp: reorder tcp_congestion_ops for better cache locality
- mptcp:
- add sockopt support for common TCP options
- add support for common TCP msg flags
- include multiple address ids in RM_ADDR
- add reset option support for resetting one subflow
- udp: GRO L4 improvements - improve 'forward' / 'frag_list'
co-existence with UDP tunnel GRO, allowing the first to take place
correctly even for encapsulated UDP traffic
- micro-optimize dev_gro_receive() and flow dissection, avoid
retpoline overhead on VLAN and TEB GRO
- use less memory for sysctls, add a new sysctl type, to allow using
u8 instead of "int" and "long" and shrink networking sysctls
- veth: allow GRO without XDP - this allows aggregating UDP packets
before handing them off to routing, bridge, OvS, etc.
- allow specifing ifindex when device is moved to another namespace
- netfilter:
- nft_socket: add support for cgroupsv2
- nftables: add catch-all set element - special element used to
define a default action in case normal lookup missed
- use net_generic infra in many modules to avoid allocating
per-ns memory unnecessarily
- xps: improve the xps handling to avoid potential out-of-bound
accesses and use-after-free when XPS change race with other
re-configuration under traffic
- add a config knob to turn off per-cpu netdev refcnt to catch
underflows in testing
Device APIs:
- add WWAN subsystem to organize the WWAN interfaces better and
hopefully start driving towards more unified and vendor-
independent APIs
- ethtool:
- add interface for reading IEEE MIB stats (incl. mlx5 and bnxt
support)
- allow network drivers to dump arbitrary SFP EEPROM data,
current offset+length API was a poor fit for modern SFP which
define EEPROM in terms of pages (incl. mlx5 support)
- act_police, flow_offload: add support for packet-per-second
policing (incl. offload for nfp)
- psample: add additional metadata attributes like transit delay for
packets sampled from switch HW (and corresponding egress and
policy-based sampling in the mlxsw driver)
- dsa: improve support for sandwiched LAGs with bridge and DSA
- netfilter:
- flowtable: use direct xmit in topologies with IP forwarding,
bridging, vlans etc.
- nftables: counter hardware offload support
- Bluetooth:
- improvements for firmware download w/ Intel devices
- add support for reading AOSP vendor capabilities
- add support for virtio transport driver
- mac80211:
- allow concurrent monitor iface and ethernet rx decap
- set priority and queue mapping for injected frames
- phy: add support for Clause-45 PHY Loopback
- pci/iov: add sysfs MSI-X vector assignment interface to distribute
MSI-X resources to VFs (incl. mlx5 support)
New hardware/drivers:
- dsa: mv88e6xxx: add support for Marvell mv88e6393x - 11-port
Ethernet switch with 8x 1-Gigabit Ethernet and 3x 10-Gigabit
interfaces.
- dsa: support for legacy Broadcom tags used on BCM5325, BCM5365 and
BCM63xx switches
- Microchip KSZ8863 and KSZ8873; 3x 10/100Mbps Ethernet switches
- ath11k: support for QCN9074 a 802.11ax device
- Bluetooth: Broadcom BCM4330 and BMC4334
- phy: Marvell 88X2222 transceiver support
- mdio: add BCM6368 MDIO mux bus controller
- r8152: support RTL8153 and RTL8156 (USB Ethernet) chips
- mana: driver for Microsoft Azure Network Adapter (MANA)
- Actions Semi Owl Ethernet MAC
- can: driver for ETAS ES58X CAN/USB interfaces
Pure driver changes:
- add XDP support to: enetc, igc, stmmac
- add AF_XDP support to: stmmac
- virtio:
- page_to_skb() use build_skb when there's sufficient tailroom
(21% improvement for 1000B UDP frames)
- support XDP even without dedicated Tx queues - share the Tx
queues with the stack when necessary
- mlx5:
- flow rules: add support for mirroring with conntrack, matching
on ICMP, GTP, flex filters and more
- support packet sampling with flow offloads
- persist uplink representor netdev across eswitch mode changes
- allow coexistence of CQE compression and HW time-stamping
- add ethtool extended link error state reporting
- ice, iavf: support flow filters, UDP Segmentation Offload
- dpaa2-switch:
- move the driver out of staging
- add spanning tree (STP) support
- add rx copybreak support
- add tc flower hardware offload on ingress traffic
- ionic:
- implement Rx page reuse
- support HW PTP time-stamping
- octeon: support TC hardware offloads - flower matching on ingress
and egress ratelimitting.
- stmmac:
- add RX frame steering based on VLAN priority in tc flower
- support frame preemption (FPE)
- intel: add cross time-stamping freq difference adjustment
- ocelot:
- support forwarding of MRP frames in HW
- support multiple bridges
- support PTP Sync one-step timestamping
- dsa: mv88e6xxx, dpaa2-switch: offload bridge port flags like
learning, flooding etc.
- ipa: add IPA v4.5, v4.9 and v4.11 support (Qualcomm SDX55, SM8350,
SC7280 SoCs)
- mt7601u: enable TDLS support
- mt76:
- add support for 802.3 rx frames (mt7915/mt7615)
- mt7915 flash pre-calibration support
- mt7921/mt7663 runtime power management fixes"
* tag 'net-next-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2451 commits)
net: selftest: fix build issue if INET is disabled
net: netrom: nr_in: Remove redundant assignment to ns
net: tun: Remove redundant assignment to ret
net: phy: marvell: add downshift support for M88E1240
net: dsa: ksz: Make reg_mib_cnt a u8 as it never exceeds 255
net/sched: act_ct: Remove redundant ct get and check
icmp: standardize naming of RFC 8335 PROBE constants
bpf, selftests: Update array map tests for per-cpu batched ops
bpf: Add batched ops support for percpu array
bpf: Implement formatted output helpers with bstr_printf
seq_file: Add a seq_bprintf function
sfc: adjust efx->xdp_tx_queue_count with the real number of initialized queues
net:nfc:digital: Fix a double free in digital_tg_recv_dep_req
net: fix a concurrency bug in l2tp_tunnel_register()
net/smc: Remove redundant assignment to rc
mpls: Remove redundant assignment to err
llc2: Remove redundant assignment to rc
net/tls: Remove redundant initialization of record
rds: Remove redundant assignment to nr_sig
dt-bindings: net: mdio-gpio: add compatible for microchip,mdio-smi0
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Another set of updates, all over the map:
* set sk_pacing_shift for 802.3->802.11 encap offload
* some monitor support for 802.11->802.3 decap offload
* HE (802.11ax) spec updates
* userspace API for TDLS HE support
* along with various other small features, cleanups and
fixups
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
In the HE capabilities, spell A-MSDU correctly, not "A-MDSU".
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210409123755.9e6ff1af1181.If6868bc6902ccd9a95c74c78f716c4b41473ef14@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The A-MPDU length exponent extension is defined differently in
802.11ax D6.1, align with that.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210409123755.c2a257d3e2df.I3455245d388c52c61dace7e7958dbed7e807cfb6@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Some names were changed, align that with the spec as of
802.11ax-D6.1.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210409123755.b1e5fbab0d8c.I3eb6076cb0714ec6aec6b8f9dee613ce4a05d825@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Don't bother keeping the link in that case. It is way
too complicated to keep the connection.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210409123755.a126c8833398.I677bdac314dd50d90474a90593902c17f9410cc4@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
In case the frequency is invalid, ieee80211_parse_ch_switch_ie
will fail and we may not even reach the check in
ieee80211_sta_process_chanswitch. Drop the connection
in case ieee80211_parse_ch_switch_ie failed, but still
take into account the CSA mode to remember not to send
a deauth frame in case if it is forbidden to.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210409123755.34712ef96a0a.I75d7ad7f1d654e8b0aa01cd7189ff00a510512b3@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This will allow the low level driver to get the wdev during
the add_interface flow.
In order to do that, remove a few checks from there and do
not return NULL for vifs that were not yet added to the
driver. Note that all the current callers of this helper
function assume that the vif already exists:
- The callers from the drivers already have a vif pointer.
Before this change, ieee80211_vif_to_wdev would return NULL
in some cases, but those callers don't even check they
get a non-NULL pointer from ieee80211_vif_to_wdev.
- The callers from net/mac80211/cfg.c assume the vif is
already added to the driver as well.
So, this change has no impact on existing callers of this
helper function.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210409123755.6078d3517095.I1907a45f267a62dab052bcc44428aa7a2005ffc9@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
As crypto_shash_setkey() can fail, we should check the return value.
Addresses-Coverity-ID: 1401813 ("Unchecked return value")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210409123755.533ff7acf1d2.I034bafa201c4a6823333f8410aeaa60cca5ee9e0@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The increment of idx is indented one level too deeply, clean up the
code by removing the extraneous tab.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210416095137.2033469-1-colin.king@canonical.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
My previous commit to not apply flow control to management frames
that are going over TXQs (which is currently only the case for
iwlwifi, I think) broke things, with iwlwifi firmware crashing on
certain frames. As it turns out, that was due to the frame being
too short: space for the MIC wasn't added at the end of encrypted
management frames.
Clearly, this is due to using the 'frags' queue - this is meant
only for frames that have already been processed for TX, and the
code in ieee80211_tx_dequeue() just returns them. This caused all
management frames to now not get any TX processing.
To fix this, use IEEE80211_TX_INTCFL_NEED_TXPROCESSING (which is
currently used only in other circumstances) to indicate that the
frames need processing, and clear it immediately after so that,
at least in theory, MMPDUs can be fragmented.
Fixes: 73bc9e0af594 ("mac80211: don't apply flow control on management frames")
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20210416134702.ef8486a64293.If0a9025b39c71bb91b11dd6ac45547aba682df34@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Conflicts:
MAINTAINERS
- keep Chandrasekar
drivers/net/ethernet/mellanox/mlx5/core/en_main.c
- simple fix + trust the code re-added to param.c in -next is fine
include/linux/bpf.h
- trivial
include/linux/ethtool.h
- trivial, fix kdoc while at it
include/linux/skmsg.h
- move to relevant place in tcp.c, comment re-wrapped
net/core/skmsg.c
- add the sk = sk // sk = NULL around calls
net/tipc/crypto.c
- trivial
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If any of the cipher schemes specified by the driver are invalid, bail
out and fail the registration rather than just warning. Otherwise, we
might later crash when we try to use the invalid cipher scheme, e.g.
if the hdr_len is (significantly) less than the pn_offs + pn_len, we'd
have an out-of-bounds access in RX validation.
Fixes: 2475b1cc0d52 ("mac80211: add generic cipher scheme support")
Link: https://lore.kernel.org/r/20210408143149.38a3a13a1b19.I6b7f5790fa0958ed8049cf02ac2a535c61e9bc96@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
After channel switch, we should consider any beacon with a
CSA IE as a new switch. If the CSA IE is a leftover from
before the switch that the AP forgot to remove, we'll get
a CSA-to-Self.
This caused issues in iwlwifi where the firmware saw a beacon
with a CSA-to-Self with mode = 1 on the new channel after a
switch. The firmware considered this a new switch and closed
its queues. Since the beacon didn't change between before and
after the switch, we wouldn't handle it (the CRC is the same)
and we wouldn't let the firmware open its queues again or
disconnect if the CSA IE stays for too long.
Clear the CRC valid state after we switch to make sure that
we handle the beacon and handle the CSA IE as required.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://lore.kernel.org/r/20210408143124.b9e68aa98304.I465afb55ca2c7d59f7bf610c6046a1fd732b4c28@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Some drivers, for example mt76, use the skb priority field, and
expects that to be consistent with the skb queue mapping. On some
frame injection code paths that was not true, and it broke frame
injection. Now the skb queue mapping is set according to the skb
priority value when the frame is injected. The skb priority value
is also derived from the frame data for all frame types, as it
was done prior to commit dbd50a851c50 (only allocate one queue
when using iTXQs). Fixes frame injection with the mt76 driver on
MT7610E chipset.
Signed-off-by: Johan Almbladh <johan.almbladh@anyfinetworks.com>
Link: https://lore.kernel.org/r/20210401164455.978245-1-johan.almbladh@anyfinetworks.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Some HW/driver can support passing ethernet rx decap frames and
raw 802.11 frames for the monitor interface concurrently and
via separate RX calls to mac80211. Packets going to the monitor
interface(s) would be in 802.11 format and thus not have the
RX_FLAG_8023 set, and 802.11 format monitoring frames should have
RX_FLAG_ONLY_MONITOR set.
Drivers doing such can enable the SUPPORTS_CONC_MON_RX_DECAP to
allow using ethernet decap offload while a monitor interface is
active, currently RX decapsulation offload gets disabled when a
monitor interface is added.
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Link: https://lore.kernel.org/r/1617068116-32253-1-git-send-email-srirrama@codeaurora.org
[add proper documentation, rewrite commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Similar to 802.11 txpath, set socket sk_pacing_shift for 802.3 tx path.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/7230abc48dcf940657838546cdaef7dce691ecdd.1615240733.git.lorenzo@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
In some cases (depending on the driver, but it's true e.g. for
iwlwifi) we're using an internal TXQ for management packets,
mostly to simplify the code and to have a place to queue them.
However, it appears that in certain cases we can confuse the
code and management frames are dropped, which is certainly not
what we want.
Short-circuit the processing of management frames. To keep the
impact minimal, only put them on the frags queue and check the
tid == management only for doing that and to skip the airtime
fairness checks, if applicable.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20210319232800.0e876c800866.Id2b66eb5a17f3869b776c39b5ca713272ea09d5d@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The variable result is being assigned a value that is never
read and it is being updated later with a new value. The
initialization is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210328213729.65819-1-colin.king@canonical.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
minstrel_ht_next_jump_rate()
GCC reports the following warning with W=1:
net/mac80211/rc80211_minstrel_ht.c:871:34: warning:
variable 'mg' set but not used [-Wunused-but-set-variable]
871 | struct minstrel_mcs_group_data *mg;
| ^~
This variable is not used in function , this commit
remove it to fix the warning.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Link: https://lore.kernel.org/r/20210326024843.987941-1-weiyongjun1@huawei.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The incorrect timeout check caused probing to happen when it did
not need to happen. This in turn caused tx performance drop
for around 5 seconds in ath10k-ct driver. Possibly that tx drop
is due to a secondary issue, but fixing the probe to not happen
when traffic is running fixes the symptom.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Fixes: 9abf4e49830d ("mac80211: optimize station connection monitor")
Acked-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20210330230749.14097-1-greearb@candelatech.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Normally, TXQs have
txq->tid = tid;
txq->ac = ieee80211_ac_from_tid(tid);
However, the special management TXQ actually has
txq->tid = IEEE80211_NUM_TIDS; // 16
txq->ac = IEEE80211_AC_VO;
This makes sense, but ieee80211_ac_from_tid(16) is the same
as ieee80211_ac_from_tid(0) which is just IEEE80211_AC_BE.
Now, normally this is fine. However, if the netdev queues
were stopped, then the code in ieee80211_tx_dequeue() will
propagate the stop from the interface (vif->txqs_stopped[])
if the AC 2 (ieee80211_ac_from_tid(txq->tid)) is marked as
stopped. On wake, however, __ieee80211_wake_txqs() will wake
the TXQ if AC 0 (txq->ac) is woken up.
If a driver stops all queues with ieee80211_stop_tx_queues()
and then wakes them again with ieee80211_wake_tx_queues(),
the ieee80211_wake_txqs() tasklet will run to resync queue
and TXQ state. If all queues were woken, then what'll happen
is that _ieee80211_wake_txqs() will run in order of HW queues
0-3, typically (and certainly for iwlwifi) corresponding to
ACs 0-3, so it'll call __ieee80211_wake_txqs() for each AC in
order 0-3.
When __ieee80211_wake_txqs() is called for AC 0 (VO) that'll
wake up the management TXQ (remember its tid is 16), and the
driver's wake_tx_queue() will be called. That tries to get a
frame, which will immediately *stop* the TXQ again, because
now we check against AC 2, and AC 2 hasn't yet been marked as
woken up again in sdata->vif.txqs_stopped[] since we're only
in the __ieee80211_wake_txqs() call for AC 0.
Thus, the management TXQ will never be started again.
Fix this by checking txq->ac directly instead of calculating
the AC as ieee80211_ac_from_tid(txq->tid).
Fixes: adf8ed01e4fd ("mac80211: add an optional TXQ for other PS-buffered frames")
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20210323210500.bf4d50afea4a.I136ffde910486301f8818f5442e3c9bf8670a9c4@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
In some race conditions, with more clients and traffic configuration,
below crash is seen when making the interface down. sta->fast_rx wasn't
cleared when STA gets removed from 4-addr AP_VLAN interface. The crash is
due to try accessing 4-addr AP_VLAN interface's net_device (fast_rx->dev)
which has been deleted already.
Resolve this by clearing sta->fast_rx pointer when STA removes
from a 4-addr VLAN.
[ 239.449529] Unable to handle kernel NULL pointer dereference at virtual address 00000004
[ 239.449531] pgd = 80204000
...
[ 239.481496] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 4.4.60 #227
[ 239.481591] Hardware name: Generic DT based system
[ 239.487665] task: be05b700 ti: be08e000 task.ti: be08e000
[ 239.492360] PC is at get_rps_cpu+0x2d4/0x31c
[ 239.497823] LR is at 0xbe08fc54
...
[ 239.778574] [<80739740>] (get_rps_cpu) from [<8073cb10>] (netif_receive_skb_internal+0x8c/0xac)
[ 239.786722] [<8073cb10>] (netif_receive_skb_internal) from [<8073d578>] (napi_gro_receive+0x48/0xc4)
[ 239.795267] [<8073d578>] (napi_gro_receive) from [<c7b83e8c>] (ieee80211_mark_rx_ba_filtered_frames+0xbcc/0x12d4 [mac80211])
[ 239.804776] [<c7b83e8c>] (ieee80211_mark_rx_ba_filtered_frames [mac80211]) from [<c7b84d4c>] (ieee80211_rx_napi+0x7b8/0x8c8 [mac8
0211])
[ 239.815857] [<c7b84d4c>] (ieee80211_rx_napi [mac80211]) from [<c7f63d7c>] (ath11k_dp_process_rx+0x7bc/0x8c8 [ath11k])
[ 239.827757] [<c7f63d7c>] (ath11k_dp_process_rx [ath11k]) from [<c7f5b6c4>] (ath11k_dp_service_srng+0x2c0/0x2e0 [ath11k])
[ 239.838484] [<c7f5b6c4>] (ath11k_dp_service_srng [ath11k]) from [<7f55b7dc>] (ath11k_ahb_ext_grp_napi_poll+0x20/0x84 [ath11k_ahb]
)
[ 239.849419] [<7f55b7dc>] (ath11k_ahb_ext_grp_napi_poll [ath11k_ahb]) from [<8073ce1c>] (net_rx_action+0xe0/0x28c)
[ 239.860945] [<8073ce1c>] (net_rx_action) from [<80324868>] (__do_softirq+0xe4/0x228)
[ 239.871269] [<80324868>] (__do_softirq) from [<80324c48>] (irq_exit+0x98/0x108)
[ 239.879080] [<80324c48>] (irq_exit) from [<8035c59c>] (__handle_domain_irq+0x90/0xb4)
[ 239.886114] [<8035c59c>] (__handle_domain_irq) from [<8030137c>] (gic_handle_irq+0x50/0x94)
[ 239.894100] [<8030137c>] (gic_handle_irq) from [<803024c0>] (__irq_svc+0x40/0x74)
Signed-off-by: Seevalamuthu Mariappan <seevalam@codeaurora.org>
Link: https://lore.kernel.org/r/1616163532-3881-1-git-send-email-seevalam@codeaurora.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
s/assocaited/associated/
Signed-off-by: Bhaskar Chowdhury <unixbhaskar@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Even if the first channel from sband channel list is invalid
or disabled mac80211 ends up choosing it as the default channel
for monitor interfaces, making them not usable.
Fix this by assigning the first available valid or enabled
channel instead.
Signed-off-by: Karthikeyan Kathirvel <kathirve@codeaurora.org>
Link: https://lore.kernel.org/r/1615440547-7661-1-git-send-email-kathirve@codeaurora.org
[reword commit message, comment, code cleanups]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
crypto_aead_encrypt returns <0 on error, so if these calls are not checked,
execution may continue with failed encrypts. It also seems that these two
crypto_aead_encrypt calls are the only instances in the codebase that are
not checked for errors.
Signed-off-by: Daniel Phan <daniel.phan36@gmail.com>
Link: https://lore.kernel.org/r/20210309204137.823268-1-daniel.phan36@gmail.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
We observed some Cisco APs sending the following HE Operation IE in
associate response:
ff 0a 24 f4 3f 00 01 fc ff 00 00 00
Its HE operation parameter is 0x003ff4, so the expected total length is
7 which does not match the actual length = 10. This causes association
failing with "HE AP is missing HE Capability/operation."
According to P802.11ax_D4 Table9-94, HE operation is extensible, and
according to 802.11-2016 10.27.8, STA should discard the part beyond
the maximum length and parse the truncated element.
Allow HE operation element to be longer than expected to handle this
case and future extensions.
Fixes: e4d005b80dee ("mac80211: refactor extended element parsing")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Yen-lin Lai <yenlinlai@chromium.org>
Link: https://lore.kernel.org/r/20210223051926.2653301-1-yenlinlai@chromium.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This probably came in through some refactoring and what is
now a call to minstrel_ht_group_min_rate_offset(), remove
the unused variable.
Reported-by: kernel test robot <lkp@intel.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20210219105744.f2538a80f6cf.I3d53554c158d5b896ac07ea546bceac67372ec28@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Clear beacon ie pointer and ie length after free
in order to prevent double free.
==================================================================
BUG: KASAN: double-free or invalid-free \
in ieee80211_ibss_leave+0x83/0xe0 net/mac80211/ibss.c:1876
CPU: 0 PID: 8472 Comm: syz-executor100 Not tainted 5.11.0-rc6-syzkaller #0
Call Trace:
__dump_stack lib/dump_stack.c:79 [inline]
dump_stack+0x107/0x163 lib/dump_stack.c:120
print_address_description.constprop.0.cold+0x5b/0x2c6 mm/kasan/report.c:230
kasan_report_invalid_free+0x51/0x80 mm/kasan/report.c:355
____kasan_slab_free+0xcc/0xe0 mm/kasan/common.c:341
kasan_slab_free include/linux/kasan.h:192 [inline]
__cache_free mm/slab.c:3424 [inline]
kfree+0xed/0x270 mm/slab.c:3760
ieee80211_ibss_leave+0x83/0xe0 net/mac80211/ibss.c:1876
rdev_leave_ibss net/wireless/rdev-ops.h:545 [inline]
__cfg80211_leave_ibss+0x19a/0x4c0 net/wireless/ibss.c:212
__cfg80211_leave+0x327/0x430 net/wireless/core.c:1172
cfg80211_leave net/wireless/core.c:1221 [inline]
cfg80211_netdev_notifier_call+0x9e8/0x12c0 net/wireless/core.c:1335
notifier_call_chain+0xb5/0x200 kernel/notifier.c:83
call_netdevice_notifiers_info+0xb5/0x130 net/core/dev.c:2040
call_netdevice_notifiers_extack net/core/dev.c:2052 [inline]
call_netdevice_notifiers net/core/dev.c:2066 [inline]
__dev_close_many+0xee/0x2e0 net/core/dev.c:1586
__dev_close net/core/dev.c:1624 [inline]
__dev_change_flags+0x2cb/0x730 net/core/dev.c:8476
dev_change_flags+0x8a/0x160 net/core/dev.c:8549
dev_ifsioc+0x210/0xa70 net/core/dev_ioctl.c:265
dev_ioctl+0x1b1/0xc40 net/core/dev_ioctl.c:511
sock_do_ioctl+0x148/0x2d0 net/socket.c:1060
sock_ioctl+0x477/0x6a0 net/socket.c:1177
vfs_ioctl fs/ioctl.c:48 [inline]
__do_sys_ioctl fs/ioctl.c:753 [inline]
__se_sys_ioctl fs/ioctl.c:739 [inline]
__x64_sys_ioctl+0x193/0x200 fs/ioctl.c:739
do_syscall_64+0x2d/0x70 arch/x86/entry/common.c:46
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Reported-by: syzbot+93976391bf299d425f44@syzkaller.appspotmail.com
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Link: https://lore.kernel.org/r/20210213133653.367130-1-markus.theil@tu-ilmenau.de
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Coverity reported the strange "if (~...)" condition that's
always true. It suggested that ! was intended instead of ~,
but upon further analysis I'm convinced that what really was
intended was a comparison to 0xff/0xffff (in HT/VHT cases
respectively), since this indicates that all of the rates
are enabled.
Change the comparison accordingly.
I'm guessing this never really mattered because a reset to
not having a rate mask is basically equivalent to having a
mask that enables all rates.
Reported-by: Colin Ian King <colin.king@canonical.com>
Fixes: 2ffbe6d33366 ("mac80211: fix and optimize MCS mask handling")
Fixes: b119ad6e726c ("mac80211: add rate mask logic for vht rates")
Reviewed-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210212112213.36b38078f569.I8546a20c80bc1669058eb453e213630b846e107b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The recent addition of in_serving_softirq() to kconv.h results in
compile failure on PREEMPT_RT because it requires
task_struct::softirq_disable_cnt. This is not available if kconv.h is
included from sched.h.
It is not needed to include kconv.h from sched.h. All but the net/ user
already include the kconv header file.
Move the include of the kconv.h header from sched.h it its users.
Additionally include sched.h from kconv.h to ensure that everything
task_struct related is available.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Andrey Konovalov <andreyknvl@google.com>
Link: https://lkml.kernel.org/r/20210218173124.iy5iyqv3a4oia4vv@linutronix.de
|
|
Allow user to disable HE mode, similar to how VHT and HT
can be disabled. Useful for testing.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Link: https://lore.kernel.org/r/20210204144610.25971-1-greearb@candelatech.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This patch adds support for STBC encoding to the radiotap tx parse
function. Prior to this change adding the STBC flag to the radiotap
header did not encode frames with STBC.
Signed-off-by: Philipp Borgers <borgers@mi.fu-berlin.de>
Link: https://lore.kernel.org/r/20210125150744.83065-1-borgers@mi.fu-berlin.de
[use u8_get_bits/u32_encode_bits instead of manually shifting]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This was added to mitigate the effects of too much sampling on devices that
use a static global fallback table instead of configurable multi-rate retry.
Now that the sampling algorithm is improved, this code path no longer performs
any better than the standard probing on affected devices.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20210127055735.78599-6-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This makes it easier to see what rates are going to be tested next
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20210127055735.78599-5-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The biggest flaw in current minstrel_ht is the fact that it needs way too
many probing packets to be able to quickly find the best rate.
Depending on the wifi hardware and operating mode, this can significantly
reduce throughput when not operating at the highest available data rate.
In order to be able to significantly reduce the amount of rate sampling,
we need a much smarter selection of probing rates.
The new approach introduced by this patch maintains a limited set of
available rates to be tested during a statistics window.
They are split into distinct categories:
- MINSTREL_SAMPLE_TYPE_INC - incremental rate upgrade:
Pick the next rate group and find the first rate that is faster than
the current max. throughput rate
- MINSTREL_SAMPLE_TYPE_JUMP - random testing of higher rates:
Pick a random rate from the next group that is faster than the current
max throughput rate. This allows faster adaptation when the link changes
significantly
- MINSTREL_SAMPLE_TYPE_SLOW - test a rate between max_prob, max_tp2 and
max_tp in order to reduce the gap between them
In order to prioritize sampling, every 6 attempts are split into 3x INC,
2x JUMP, 1x SLOW.
Available rates are checked and refilled on every stats window update.
With this approach, we finally get a very small delta in throughput when
comparing setting the optimal data rate as a fixed rate vs normal rate
control operation.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20210127055735.78599-4-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
In order to more gracefully be able to fall back to lower rates without too
much throughput fluctuations, initialize all untested rates below tested ones
to the maximum probabilty of higher rates.
Usually this leads to untested lower rates getting initialized with a
probability value of 100%, making them better candidates for fallback without
having to rely on random probing
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20210127055735.78599-3-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Keep the update in one place and prepare for further rework
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20210127055735.78599-2-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Get rid of a lot of divisions and modulo operations
Reduces code size and improves performance
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20210127055735.78599-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The multiplication of the u32 variables tx_time and estimated_retx is
performed using a 32 bit multiplication and the result is stored in
a u64 result. This has a potential u32 overflow issue, so avoid this
by casting tx_time to a u64 to force a 64 bit multiply.
Addresses-Coverity: ("Unintentional integer overflow")
Fixes: 050ac52cbe1f ("mac80211: code for on-demand Hybrid Wireless Mesh Protocol")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210205175352.208841-1-colin.king@canonical.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
