summaryrefslogtreecommitdiff
path: root/net/mac80211
AgeCommit message (Collapse)Author
2016-01-20net/mac80211/debugfs.c: prevent build failure with CONFIG_UBSAN=yAndrey Ryabinin
With upcoming CONFIG_UBSAN the following BUILD_BUG_ON in net/mac80211/debugfs.c starts to trigger: BUILD_BUG_ON(hw_flag_names[NUM_IEEE80211_HW_FLAGS] != (void *)0x1); It seems, that compiler instrumentation causes some code deoptimizations. Because of that GCC is not being able to resolve condition in BUILD_BUG_ON() at compile time. We could make size of hw_flag_names array unspecified and replace the condition in BUILD_BUG_ON() with following: ARRAY_SIZE(hw_flag_names) != NUM_IEEE80211_HW_FLAGS That will have the same effect as before (adding new flag without updating array will trigger build failure) except it doesn't fail with CONFIG_UBSAN. As a bonus this patch slightly decreases size of hw_flag_names array. Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com> Cc: Johannes Berg <johannes@sipsolutions.net> Cc: "David S. Miller" <davem@davemloft.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2015-12-17Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller
Conflicts: drivers/net/geneve.c Here we had an overlapping change, where in 'net' the extraneous stats bump was being removed whilst in 'net-next' the final argument to udp_tunnel6_xmit_skb() was being changed. Signed-off-by: David S. Miller <davem@davemloft.net>
2015-12-15mac80211: handle width changes from opmode notification IE in beaconEyal Shapira
An AP can send an operating channel width change in a beacon opmode notification IE as long as there's a change in the nss as well (See 802.11ac-2013 section 10.41). So don't limit updating to nss only from an opmode notification IE. Signed-off-by: Eyal Shapira <eyalx.shapira@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-12-15mac80211: suppress unchanged "limiting TX power" messagesJohannes Berg
When the AP is advertising limited TX power, the message can be printed over and over again. Suppress it when the power level isn't changing. This fixes https://bugzilla.kernel.org/show_bug.cgi?id=106011 Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-12-15mac80211: reprogram in interface orderJohannes Berg
During reprogramming, mac80211 currently first adds all the channel contexts, then binds them to the vifs and then goes to reconfigure all the interfaces. Drivers might, perhaps implicitly, rely on the operation order for certain things that typically happen within a single function elsewhere in mac80211. To avoid problems with that, reorder the code in mac80211's restart/reprogramming to work fully within the interface loop so that the order of operations is like in normal operation. For iwlwifi, this fixes a firmware crash when reprogramming with an AP/GO interface active. Reported-by: David Spinadel <david.spinadel@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-12-15mac80211: run scan completed work on reconfig failureJohannes Berg
When reconfiguration during resume fails while a scan is pending for completion work, that work will never run, and the scan will be stuck forever. Factor out the code to recover this and call it also in ieee80211_handle_reconfig_failure(). Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-12-07mac80211: handle HW ROC expired properlyIlan Peer
In case of HW ROC, when the driver reports that the ROC expired, it is not sufficient to purge the ROCs based on the remaining time, as it possible that the device finished the ROC session before the actual requested duration. To handle such cases, in case of ROC expired notification from the driver, complete all the ROCs which are marked with hw_begun, regardless of the remaining duration. Signed-off-by: Ilan Peer <ilan.peer@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-12-04mac80211: reject zero cookie in mgmt-tx/roc cancelJohannes Berg
When cancelling, you can cancel "any" (first in list) mgmt-tx or remain-on-channel operation by using the value 0 for the cookie along with the *opposite* operation, i.e. * cancel the first mgmt-tx by cancelling roc with 0 cookie * cancel the first roc by cancelling mgmt-tx with 0 cookie This isn't really that bad since userspace should only pass cookies that we gave it, but could lead to hard-to-debug issues so better prevent it and reject zero values since we never hand those out. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-12-04mac80211: Allow a STA to join an IBSS with 80+80 MHz channelJouni Malinen
While it was possible to create an IBSS with 80+80 MHz channel, joining such an IBSS resulted in falling back to 20 MHz channel with VHT disabled due to a missing switch case for 80+80. Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-12-04mac80211: rewrite remain-on-channel logicJohannes Berg
Jouni found a bug in the remain-on-channel logic: when a short item is queued, a long item is combined with it extending the original one, and then the long item is deleted, the timeout doesn't go back to the short one, and the short item ends up taking a long time. In this case, this showed as blocking scan when running two test cases back to back - the scan from the second was delayed even though all the remain-on-channel items should long have been gone. Fixing this with the current data structures turns out to be a bit complicated, we just remove the long item from the dependents list right now and don't recalculate the timeouts. There's a somewhat similar bug where we delete the short item and all the dependents go with it; to fix this we'd have to move them from the dependents to the real list. Instead of trying to do that, rewrite the code to not have all this complexity in the data structures: use a single list and allow more than one entry in it being marked as started. This makes the code a bit more complex, the worker needs to understand that it might need to just remove one of the started items, while keeping the device off-channel, but that's not more complicated than the nested data structures. This then fixes both issues described, and makes it easier to also limit the overall off-channel time when combining. TODO: as before, with hardware remain-on-channel, deleting an item after combining results in cancelling them all - we can keep track of the time elapsed and only cancel after that to fix this. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-12-04mac80211: simplify ack_skb handlingJohannes Berg
Since the cookie is assigned inside ieee80211_make_ack_skb() now, we no longer need to return the ack_skb as the cookie and can simplify the function's return and the callers. Also rename it to ieee80211_attach_ack_skb() to more accurately reflect its purpose. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-12-04mac80211: move off-channel/mgmt-tx code to offchannel.cJohannes Berg
This is quite a bit of code that logically depends here since it has to deal with all the remain-on-channel logic. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-12-04mac80211: fix mgmt-tx abort cookie and leakJohannes Berg
If a mgmt-tx operation is aborted before it runs, the wrong cookie is reported back to userspace, and the ack_skb gets leaked since the frame is freed directly instead of freeing it using ieee80211_free_txskb(). Fix that. Fixes: 3b79af973cf4 ("mac80211: stop using pointers as userspace cookies") Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-12-04mac80211: catch queue stop underflowJohannes Berg
If some code stops the queues more times than having started (for when refcounting is used), warn on and reset the counter to 0 to avoid blocking forever. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-12-04mac80211: properly free TX skbs when monitor TX failsJohannes Berg
We need to free all skbs here, not just the one we peeked from the list. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-12-04mac80211: properly free skb when r-o-c for TX failsJohannes Berg
When freeing the TX skb for an off-channel TX, use the correct API to also free the ACK skb that might have been allocated. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-12-04Revert "mac80211: don't advertise NL80211_FEATURE_FULL_AP_CLIENT_STATE"Johannes Berg
This reverts commit 45bb780a2147b9995f3d288c44ecb87ca8a330e2, the previous two patches fixed the functionality. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-12-04cfg80211: handle add_station auth/assoc flag quirksJohannes Berg
When a new station is added to AP/GO interfaces the default behaviour is for it to be added authenticated and associated, due to backwards compatibility. To prevent that, the driver must be able to do that (setting the NL80211_FEATURE_FULL_AP_CLIENT_STATE feature flag) and userspace must set the flag mask to auth|assoc and clear the set. Handle this quirk in the API entirely in nl80211, and always push the full flags to the drivers. NL80211_FEATURE_FULL_AP_CLIENT_STATE is still required for userspace to be allowed to set the mask including those bits, but after checking that add both flags to the mask and set in case userspace didn't set them otherwise. This obsoletes the mac80211 code handling this difference, no other driver is currently using these flags. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-12-04mac80211: Add support for aborting an ongoing scanVidyullatha Kanchanapally
This commit adds implementation for abort scan in mac80211. Reviewed-by: Jouni Malinen <jouni@qca.qualcomm.com> Signed-off-by: Vidyullatha Kanchanapally <vkanchan@qti.qualcomm.com> Signed-off-by: Sunil Dutt <usdutt@qti.qualcomm.com> [adjust to wdev change in previous patch and clean up code a bit] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-12-04mac80211: add new IEEE80211_VIF_GET_NOA_UPDATE flagJanusz.Dziedzic@tieto.com
Add new VIF flag, that will allow get NOA update notification when driver will request this, even this is not pure P2P vif (eg. STA vif). Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-12-04mac80211: add atomic uploaded keys iteratorEliad Peller
add ieee80211_iter_keys_rcu() to iterate over uploaded keys in atomic context (when rcu is locked) The station removal code removes the keys only after calling synchronize_net(), so it's not safe to iterate the keys at this point (and postponing the actual key deletion with call_rcu() might result in some badly-ordered ops calls). Add a flag to indicate a station is being removed, and skip the configured keys if it's set. Signed-off-by: Eliad Peller <eliadx.peller@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-12-04mac80211: allow the driver to send EOSP when neededEmmanuel Grumbach
This can happen when the driver needs to send less frames than expected and then needs to close the SP. Mac80211 still needs to set the more_data properly based on its buffer state (ps_tx_buffer and buffered frames on other TIDs). To that end, refactor the code that delivers frames upon uAPSD trigger frames to be able to get only the more_data bit without actually delivering those frames in case the driver is just asking to set a NDP with EOSP and MORE_DATA bit properly set. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-12-04mac80211: remove string from unaligned packet warningJohannes Berg
This really should never happen except very early in the process of bringing up a new driver, at which point you'll have to add more debugging in the driver and this string isn't useful. Remove it and save some size (when it's even compiled in.) Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-12-04mac80211: mesh: print MAC address instead of pointerJohannes Berg
There's no point in printing the mpath pointer since it can't be used for anything - print the MAC address instead (like in the forwarding case.) Signed-off-by: Johannes Berg <johannes.berg@intel.com> Acked-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-12-04mac80211: allow driver to prevent two stations w/ same addressJohannes Berg
Some devices or drivers cannot deal with having the same station address for different virtual interfaces, say as a client to two virtual AP interfaces. Rather than requiring each driver with a limitation like that to enforce it, add a hardware flag for it. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-12-02mac80211: fix off-channel mgmt-tx uninitialized variable usageJohannes Berg
In the last change here, I neglected to update the cookie in one code path: when a mgmt-tx has no real cookie sent to userspace as it doesn't wait for a response, but is off-channel. The original code used the SKB pointer as the cookie and always assigned the cookie to the TX SKB in ieee80211_start_roc_work(), but my change turned this around and made the code rely on a valid cookie being passed in. Unfortunately, the off-channel no-wait TX path wasn't assigning one at all, resulting in an uninitialized stack value being used. This wasn't handed back to userspace as a cookie (since in the no-wait case there isn't a cookie), but it was tested for non-zero to distinguish between mgmt-tx and off-channel. Fix this by assigning a dummy non-zero cookie unconditionally, and get rid of a misleading comment and some dead code while at it. I'll clean up the ACK SKB handling separately later. Fixes: 3b79af973cf4 ("mac80211: stop using pointers as userspace cookies") Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-12-02mac80211: do not actively scan DFS channelsAntonio Quartulli
DFS channels should not be actively scanned as we can't be sure if we are allowed or not. If the current channel is in the DFS band, active scan might be performed after CSA, but we have no guarantee about other channels, therefore it is safer to prevent active scanning at all. Cc: stable@vger.kernel.org Signed-off-by: Antonio Quartulli <antonio@open-mesh.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-12-02mac80211: don't teardown sdata on sdata stopEliad Peller
Interfaces are being initialized (setup) on addition, and torn down on removal. However, p2p device is being torn down when stopped, resulting in the next p2p start operation being done on uninitialized interface. Solve it by calling ieee80211_teardown_sdata() only on interface removal (for the non-netdev case). Signed-off-by: Eliad Peller <eliadx.peller@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> [squashed in fix to call teardown after unregister] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-11-20mac80211: always set the buf_size in AddBA req to 64Gregory Greenman
Advertising reordering window in ADDBA less than 64 can crash some APs, an example is LinkSys WRT120N (with FW v1.0.07 build 002 Jun 18 2012). On the other hand, a driver may need to limit Tx A-MPDU size for its own reasons, like specific HW limitations. Signed-off-by: Gregory Greenman <gregory.greenman@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-11-20mac80211: ensure we don't update tx power on a non-running sdataEmmanuel Grumbach
We can't update the Tx power on the device unless it is running. This fixes https://bugzilla.kernel.org/show_bug.cgi?id=101521. Cc: stable@vger.kernel.org Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-11-17mac80211: mesh: fix call_rcu() usageJohannes Berg
When using call_rcu(), the called function may be delayed quite significantly, and without a matching rcu_barrier() there's no way to be sure it has finished. Therefore, global state that could be gone/freed/reused should never be touched in the callback. Fix this in mesh by moving the atomic_dec() into the caller; that's not really a problem since we already unlinked the path and it will be destroyed anyway. This fixes a crash Jouni observed when running certain tests in a certain order, in which the mesh interface was torn down, the memory reused for a function pointer (work struct) and running that then crashed since the pointer had been decremented by 1, resulting in an invalid instruction byte stream. Cc: stable@vger.kernel.org Fixes: eb2b9311fd00 ("mac80211: mesh path table implementation") Reported-by: Jouni Malinen <j@w1.fi> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-11-17mac80211: don't advertise NL80211_FEATURE_FULL_AP_CLIENT_STATEJohannes Berg
For now, this feature doesn't actually work. To avoid shipping a kernel that has it enabled but where it can't be used disable it for now - we can re-enable it when it's fixed. This partially reverts 44674d9c2267 ("mac80211: advertise support for full station state in AP mode"). Cc: Ayala Beker <ayala.beker@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-11-03mac80211: document sleep requirements for channel context opsChaitanya T K
Channel context driver operations can sleep, so add might_sleep() and document this. Signed-off-by: Chaitanya T K <chaitanya.mgit@gmail.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-11-03mac80211: further improve "no supported rates" warningJohannes Berg
Allow distinguishing the non-station case from the case of a station without rates, by using -1 for the non-station case. This value cannot be reached with a station since that many legacy rates don't exist. Signed-off-by: Johannes Berg <johannes.berg@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-11-03mac80211: treat bad WMM parameters more gracefullyJohannes Berg
As WMM is required for HT/VHT operation, treat bad WMM parameters more gracefully by falling back to default parameters instead of not using WMM assocation. This makes it possible to still use HT or VHT, although potentially with reduced quality of service due to unintended WMM parameters. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-11-03mac80211: fixup AIFSN instead of disabling WMMEmmanuel Grumbach
Disabling WMM has a huge impact these days. It implies that HT and VHT will be disabled which means that the throughput will be drammatically reduced. Since the AIFSN is a transmission parameter, we can play a bit and fix it up to make it compliant with the 802.11 specification which requires it to be at least 2. Increasing it from 1 to 2 will slightly reduce the likelyhood to get a transmission opportunity compared to other clients that would accept to set AIFSN=1, but at least it will allow HT and VHT which is a huge gain. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-11-03mac80211: make enable_qos parameter to ieee80211_set_wmm_default()Johannes Berg
The function currently determines this value, for use in bss_info.qos, based on the interface type itself. Make it a parameter instead and set it with the same logic for now. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-11-03mac80211: fix crash on mesh local link ID generation with VIFsMatthias Schiffer
llid_in_use needs to be limited to stations of the same VIF, otherwise it will cause a NULL deref as the sta_info of non-mesh-VIFs don't have sta->mesh set. Steps to reproduce: modprobe mac80211_hwsim channels=2 iw phy phy0 interface add ibss0 type ibss iw phy phy0 interface add mesh0 type mp iw phy phy1 interface add ibss1 type ibss iw phy phy1 interface add mesh1 type mp ip link set ibss0 up ip link set mesh0 up ip link set ibss1 up ip link set mesh1 up iw dev ibss0 ibss join foo 2412 iw dev ibss1 ibss join foo 2412 # Ensure that ibss0 and ibss1 are actually associated; I often need to # leave and join the cell on ibss1 a second time. iw dev mesh0 mesh join bar iw dev mesh1 mesh join bar # crash Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-11-03mac80211: TDLS: add proper HT-oper IEArik Nemtsov
When 11n peers performs a TDLS connection on a legacy BSS, the HT operation IE must be specified according to IEEE802.11-2012 section 9.23.3.2. Otherwise HT-protection is compromised and the medium becomes noisy for both the TDLS and the BSS links. Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-11-03mac80211: don't reconfigure sched scan in case of wowlanEliad Peller
Scheduled scan has to be reconfigured only if wowlan wasn't configured, since otherwise it should continue to run (with the 'any' trigger) or be aborted. The current code will end up asking the driver to start a new scheduled scan without stopping the previous one, and leaking some memory (from the previous request.) Fix this by doing the abort/restart under the proper conditions. Signed-off-by: Eliad Peller <eliadx.peller@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-11-03mac80211: call drv_stop only if driver is startedEliad Peller
If drv_start() fails during hw_restart, all the running interfaces are being closed/stopped, which results in drv_stop() being called, although the driver was never started successfully. This might cause drivers to perform operations on uninitialized memory (as they assume it was initialized on drv_start) Consider the local->started flag, and call the driver's stop() op only if drv_start() succeeded before. Move drv_start() and drv_stop() to driver-ops.c, as they are no longer simple wrappers. Signed-off-by: Eliad Peller <eliadx.peller@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-11-03mac80211: Remove WARN_ON_ONCE in ieee80211_recalc_smpsAndrei Otcheretianski
The recalc_smps work can run after the station disassociates. At this stage we already released the channel, but the work will be cancelled only when the interface stops. In this scenario we can hit the warning in ieee80211_recalc_smps, so just remove it. Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-11-03mac80211: use freezable workqueue for restart workEliad Peller
Requesting hw restart during suspend might result in the restart work being executed after mac80211 and the hw are suspended. Solve the race by simply scheduling the restart work on a freezable workqueue. Note that there can be some cases of reconfiguration on resume (besides the hardware restart): * wowlan is not configured - All the interfaces removed were removed on suspend, and drv_stop() was called. At this point the driver shouldn't expect for hw_restart anyway, so we can simply cancel it (on resume). * wowlan is configured, drv_resume() == 1 There is no definitive expected behavior in this case, as each driver might have different expectations (e.g. setting some flags on suspend/restart vs. not handling spurious recovery). For now, simply let the hw_restart work run again after resume, and hope the driver will handle it well (or at least initiate another hw restart). Signed-off-by: Eliad Peller <eliadx.peller@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-11-03mac80211: Fix local deauth while associatingAndrei Otcheretianski
Local request to deauthenticate wasn't handled while associating, thus the association could continue even when the user space required to disconnect. Cc: stable@vger.kernel.org Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-11-03mac80211: allow null chandef in tracingArik Nemtsov
In TDLS channel-switch operations the chandef can sometimes be NULL. Avoid an oops in the trace code for these cases and just print a chandef full of zeros. Cc: stable@vger.kernel.org Fixes: a7a6bdd0670fe ("mac80211: introduce TDLS channel switch ops") Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-11-03mac80211: fix divide by zero when NOA updateJanusz.Dziedzic@tieto.com
In case of one shot NOA the interval can be 0, catch that instead of potentially (depending on the driver) crashing like this: divide error: 0000 [#1] SMP [...] Call Trace: <IRQ> [<ffffffffc08e891c>] ieee80211_extend_absent_time+0x6c/0xb0 [mac80211] [<ffffffffc08e8a17>] ieee80211_update_p2p_noa+0xb7/0xe0 [mac80211] [<ffffffffc069cc30>] ath9k_p2p_ps_timer+0x170/0x190 [ath9k] [<ffffffffc070adf8>] ath_gen_timer_isr+0xc8/0xf0 [ath9k_hw] [<ffffffffc0691156>] ath9k_tasklet+0x296/0x2f0 [ath9k] [<ffffffff8107ad65>] tasklet_action+0xe5/0xf0 [...] Cc: stable@vger.kernel.org [3.16+, due to d463af4a1c34 using it] Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-10-22Merge tag 'mac80211-next-for-davem-2015-10-21' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next Johannes Berg says: ==================== Here's another set of patches for the current cycle: * I merged net-next back to avoid a conflict with the * cfg80211 scheduled scan API extensions * preparations for better scan result timestamping * regulatory cleanups * mac80211 statistics cleanups * a few other small cleanups and fixes ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2015-10-21mac80211: move station statistics into sub-structsJohannes Berg
Group station statistics by where they're (mostly) updated (TX, RX and TX-status) and group them into sub-structs of the struct sta_info. Also rename the variables since the grouping now makes it obvious where they belong. This makes it easier to identify where the statistics are updated in the code, and thus easier to think about them. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-10-21mac80211: move beacon_loss_count into ifmgdJohannes Berg
There's little point in keeping (and even sending to userspace) the beacon_loss_count value per station, since it can only apply to the AP on a managed-mode connection. Move the value to ifmgd, advertise it only in managed mode, and remove it from ethtool as it's available through better interfaces. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2015-10-21mac80211: remove sta->last_ack_signalJohannes Berg
This file only feeds a debugfs file that isn't very useful, so remove it. If necessary, we can add other ways to get this information, for example in the NL80211_CMD_PROBE_CLIENT response. Signed-off-by: Johannes Berg <johannes.berg@intel.com>