| Age | Commit message (Collapse) | Author |
|---|
|
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Have proper request id filled in the SCHED_SCAN_RESULTS and
SCHED_SCAN_STOPPED notifications toward user-space by having the
driver provide it through the api.
Reviewed-by: Hante Meuleman <hante.meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Reviewed-by: Franky Lin <franky.lin@broadcom.com>
Signed-off-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The issue was found when entering suspend and resume.
It triggers a warning in:
mac80211/key.c: ieee80211_enable_keys()
...
WARN_ON_ONCE(sdata->crypto_tx_tailroom_needed_cnt ||
sdata->crypto_tx_tailroom_pending_dec);
...
It points out sdata->crypto_tx_tailroom_pending_dec isn't cleaned up successfully
in a delayed_work during suspend. Add a flush_delayed_work to fix it.
Cc: stable@vger.kernel.org
Signed-off-by: Matt Chen <matt.chen@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
__ieee80211_suspend() checks early on if there's anything
to do by checking open_count, so there's no need to check
again later in the function. Remove the useless check.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Scheduled scan has to be reconfigured only if wowlan wasn't
configured, since otherwise it should continue to run (with
the 'any' trigger) or be aborted.
The current code will end up asking the driver to start a new
scheduled scan without stopping the previous one, and leaking
some memory (from the previous request.)
Fix this by doing the abort/restart under the proper conditions.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
In case of "any" wowlan trigger, there is no reason to tear down
aggregations, as we want the device to continue working normally.
Similarly, there's no reason to tear down aggregations on resume,
as they should have been torn down on suspend if needed.
However, since the reconfiguration flow is shared with HW restart,
tear down aggregations on reconfiguration when we are not resuming.
To keep things working after non-wowlan suspend, keep clearing the
WLAN_STA_BLOCK_BA flag.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
If for any reason we're in the middle of PS-polling or awake after
TX due to dynamic powersave while going to suspend, go back to save
power. This might cause a response frame to get lost, but since we
can't really wait for it while going to suspend that's still better
than not enabling powersave which would cause higher power usage
during (and possibly even after) suspend.
Note that this really only affects the very few drivers that use
the powersave implementation in mac80211.
Signed-off-by: Chaitanya T K <chaitanya.mgit@gmail.com>
[rewrite misleading commit log]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
As we're running out of hardware capability flags pretty quickly,
convert them to use the regular test_bit() style unsigned long
bitmaps.
This introduces a number of helper functions/macros to set and to
test the bits, along with new debugfs code.
The occurrences of an explicit __clear_bit() are intentional, the
drivers were never supposed to change their supported bits on the
fly. We should investigate changing this to be a per-frame flag.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
If the driver rejects WoWLAN, restart the queues before returning
to cfg80211. cfg80211 will return to mac80211, but not before it
disconnects all interfaces. If we don't start the queues, any of
the packets needed for disconnecting won't be transmitted, which
is strange. Fix that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
We check local->open_count at the top of the __ieee80211_suspend(), so
there's no need to check for it again. open_count is protected by the
rtnl, so there's no chance for it to have change between the two
calls.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Drivers can't really be expected to suspend properly while auth
or assoc is in progress since then they don't have any state
they could keep with WoWLAN, nor can they actually finish the
authentication or association. In fact, keeping this can cause
subtle issues with drivers like iwlwifi that refuse WoWLAN if
not associated, but have trouble figuring out what's going on
in the middle of association.
In any case, regardless of possible driver issues in this area,
it doesn't make sense for mac80211 to try to WoWLAN-suspend in
the middle of such operations, so stop them before.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Conflicts:
arch/arm/boot/dts/imx6sx-sdb.dts
net/sched/cls_bpf.c
Two simple sets of overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In normal cases (i.e. when we are fully associated), cfg80211 takes
care of removing all the stations before calling suspend in mac80211.
But in the corner case when we suspend during authentication or
association, mac80211 needs to roll back the station states. But we
shouldn't roll back the station states in the suspend function,
because this is taken care of in other parts of the code, except for
WDS interfaces. For AP types of interfaces, cfg80211 takes care of
disconnecting all stations before calling the driver's suspend code.
For station interfaces, this is done in the quiesce code.
For WDS interfaces we still need to do it here, so move the code into
a new switch case for WDS.
Cc: stable@kernel.org [3.15+]
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When roaming / suspending, it makes no sense to wait until
the transmit queues of the device are empty. In extreme
condition they can be starved (VO saturating the air), but
even in regular cases, it is pointless to delay the roaming
because the low level driver is trying to send packets to
an AP which is far away. We'd rather drop these packets and
let TCP retransmit if needed. This will allow to speed up
the roaming.
For suspend, the explanation is even more trivial.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Sometimes different vifs may be stopping the queues for the same
reason (e.g. when several interfaces are performing a channel switch).
Instead of using a bitmask for the reasons, use an integer that holds
a refcount instead. In order to keep it backwards compatible,
introduce a boolean in some functions that tell us whether the queue
stopping should be refcounted or not. For now, use not refcounted for
all calls to keep it functionally the same as before.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Since Stanislaw's patch removing the quiescing code, mac80211 had
a race regarding suspend vs. authentication: as cfg80211 doesn't
track authentication attempts, it can't abort them. Therefore the
attempts may be kept running while suspending, which can lead to
all kinds of issues, in at least some cases causing an error in
iwlmvm firmware.
Fix this by aborting the authentication attempt when suspending.
Cc: stable@vger.kernel.org
Fixes: 12e7f517029d ("mac80211: cleanup generic suspend/resume procedures")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
If we can assume that stations are never referenced by the
driver after sta_state returns (and this is true since the
previous iwlmvm patch and for all other drivers) then we
don't need to delay station destruction, and don't need to
play tricks with rcu_barrier() etc.
This should speed up some scenarios like hostapd shutdown.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
My commit:
commit 12e7f517029dad819c45eca9ca01fdb9ba57616b
Author: Stanislaw Gruszka <sgruszka@redhat.com>
Date: Thu Feb 28 10:55:26 2013 +0100
mac80211: cleanup generic suspend/resume procedures
removed check for deleting MONITOR and AP_VLAN when suspend. That can
cause a crash (i.e. in iwlagn_mac_remove_interface()) since we remove
interface in the driver that we did not add before.
Reference:
http://marc.info/?l=linux-kernel&m=137391815113860&w=2
Bisected-by: Ortwin Glück <odi@odi.ch>
Reported-and-tested-by: Ortwin Glück <odi@odi.ch>
Cc: stable@vger.kernel.org # 3.10
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The RCU docs used to state that rcu_barrier() included a wait
for an RCU grace period; however the comments for rcu_barrier()
as of commit f0a0e6f... "rcu: Clarify memory-ordering properties
of grace-period primitives" contradict this.
So add back synchronize_{rcu,net}() to where they once were,
but keep the rcu_barrier()s for the call_rcu() callbacks.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Bob Copeland <bob@cozybit.com>
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Since Stanislaw's patches, when suspending while connected,
cfg80211 will disconnect. This causes the AP station to be
removed, which uses call_rcu() to clean up. Due to needing
process context, this queues a work struct on the mac80211
workqueue. This will warn and fail when already suspended,
which can happen if the rcu call doesn't happen quickly.
To fix this, replace the synchronize_net() which is really
just synchronize_rcu_expedited() with rcu_barrier(), which
unlike synchronize_rcu() waits until RCU callback have run
and thus avoids this issue.
In theory, this can even happen without Stanislaw's change
to disconnect on suspend since userspace might disconnect
just before suspending, though then it's unlikely that the
call_rcu() will be delayed long enough.
Cc: stable@vger.kernel.org [3.7+]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
It has to be removed from the driver, but completely
destroying it helps handle unplug of a device during
suspend since then the channel context handling etc.
doesn't have to happen later when it's removed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
They can't really be executed while suspended and could
trigger work warnings, so abort all ROC items. When the
system resumes the notifications about this will be
delivered to userspace which can then act accordingly
(though it will assume they were canceled/finished.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Sometimes queues are flushed in the middle of
operation, which can lead to driver issues.
Stop queues temporarily, while flushing, to
avoid transmitting new packets while they are
being flushed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
There are a number of situations in which mac80211 only
really needs to flush queues for one virtual interface,
and in fact during this frames might be transmitted on
other virtual interfaces. Calculate and pass a queue
bitmap to the driver so it knows which queues to flush.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Since now we disconnect before suspend, various code which save
connection state can now be removed from suspend and resume
procedure. Cleanup on resume side is smaller as ieee80211_reconfig()
is also used for H/W restart.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
If possible that after suspend, cfg80211 will receive request to
disconnect what require action on interface that was removed during
suspend.
Problem can manifest itself by various warnings similar to below one:
WARNING: at net/mac80211/driver-ops.h:12 ieee80211_bss_info_change_notify+0x2f9/0x300 [mac80211]()
wlan0: Failed check-sdata-in-driver check, flags: 0x4
Call Trace:
[<c043e0b3>] warn_slowpath_fmt+0x33/0x40
[<f83707c9>] ieee80211_bss_info_change_notify+0x2f9/0x300 [mac80211]
[<f83a660a>] ieee80211_recalc_ps_vif+0x2a/0x30 [mac80211]
[<f83a6706>] ieee80211_set_disassoc+0xf6/0x500 [mac80211]
[<f83a9441>] ieee80211_mgd_deauth+0x1f1/0x280 [mac80211]
[<f8381b36>] ieee80211_deauth+0x16/0x20 [mac80211]
[<f8261e70>] cfg80211_mlme_down+0x70/0xc0 [cfg80211]
[<f8264de1>] __cfg80211_disconnect+0x1b1/0x1d0 [cfg80211]
To fix the problem disconnect from any associated network before
suspend. User space is responsible to establish connection again
after resume. This basically need to be done by user space anyway,
because associated stations can go away during suspend (for example
NetworkManager disconnects on suspend and connect on resume by default).
Patch also handle situation when driver refuse to suspend with wowlan
configured and try to suspend again without it.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add command to trigger radar detection in the driver/FW.
Once radar detection is started it should continuously
monitor for radars as long as the channel active.
If radar is detected usermode notified with 'radar
detected' event.
Scanning and remain on channel functionality must be disabled
while doing radar detection/scanning, and vice versa.
Based on original patch by Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When waking up from WoWLAN, it is useful to know
what triggered the wakeup. Support reporting the
wakeup reason(s) in cfg80211 (and a pass-through
in mac80211) to allow userspace to know.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The initiator/tx doesn't really identify why an
aggregation session is stopped, give a reason
for stopping that more clearly identifies what's
going on. This will help tell the driver clearly
what is expected of it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Instead of checking every time bss_info_changed is called,
assign the pointer once depending on the interface type
and then leave it untouched until the interface type is
changed. This makes the ieee80211_bss_info_change_notify()
now a simple wrapper to call the driver only.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The special case in the function isn't really needed,
instead make the suspend code a bit better and also
easier to understand and move the warning into the
driver op wrapper inline.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When suspending, bss_info_changed() is called to
disable beacons, but managed mode interfaces are
simply removed (bss_info_changed() is called with
"no change" only). This can lead to problems.
To fix this and copy the BSS configuration, clear
it during suspend and restore it on resume.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
It's a bit odd that there's a return value that only
depends on the iftype, move that logic out of the
function into the only caller that needs it.
Also, since the quiescing could stop timers that
trigger the sdata work, move the sdata work cancel
into the function and after the actual quiesce.
Finally, there's no need to call it on interfaces
that are down, so don't.
Change-Id: I1632d46d21ba3558ea713d035184f1939905f2f1
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Sujith reported warnings with suspend/resume due to
channel contexts. When I looked into it, I realised
that the code was completely broken as it unassigned
the channel contexts when suspending, which actually
means they are destroyed.
Eliad Peller then pointed out that we also need to
remove the channel contexts from the driver. When I
looked into this, I also noticed that the code isn't
handling the virtual monitor interface correctly (if
it exists.)
Fix this by calling just the driver methods (if they
are implemented) instead of using the channel context
management code. Also add reconfiguration for the
virtual monitor interface.
Reported-by: Sujith Manoharan <sujith@msujith.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Depending on the driver, a lot of setup may be
necessary to start operating as an AP, some of
which may fail. Add an explicit AP start driver
method to make such failures easier to handle,
and add an AP stop driver method for symmetry.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Instead of operating on a single channel only,
use the new channel context infrastructure in
all mac80211 code.
This enables drivers that want to use the new
channel context infrastructure to use multiple
channels, while nothing should change for all
the other drivers that don't support it.
Right now this disables both TX power settings
and spatial multiplexing powersave. Both need
to be re-enabled on a channel context basis.
Additionally, when channel contexts are used
drop the connection when channel switch is
received rather than trying to handle it. This
will have to be improved later.
[With fixes from Eliad and Emmanuel incorporated]
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
In case the driver suspend callback fails, mac80211 is left
with stopped queues which prevents any further traffic as well
as all STAs are left marked with WLAN_STA_BLOCK_BA which will
cause any further ADDBA requests to be declined. Fix it by
undoing both before returning from __iee80211_suspend.
Reported-by: Vitaly Wool <vitalywool@gmail.com>
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
drv_resume can get called without a prior call to drv_suspend.
Consider the following steps:
1. Suspend is started but driver's drv_suspend returns error.
2. Suspend is aborted. local->wowlan flag is left set.
3. Interface is removed.
4. Suspend again. This time open_count is 0 so drv_suspend is
not called and local->wowlan not cleared.
5. On resume ieee80211_reconfig will call drv_resume since
local->wowlan is set.
Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The queue mapping redesign that I'm planning to do
will break pure injection unless we handle monitor
interfaces explicitly. One possible option would
be to have the driver tell mac80211 about monitor
mode queues etc., but that would duplicate the API
since we already need to have queue assignments
handled per virtual interface.
So in order to solve this, have a virtual monitor
interface that is added whenever all active vifs
are monitors. We could also use the state of one
of the monitor interfaces, but managing that would
be complicated, so allocate separate state.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Use interface data from sta instead of invalid pointer
to list head in calls to drv_sta_state.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Instead of maintaining separate sta_add/sta_remove
callsites, implement it in sta_state when the driver
has no sta_state implementation.
The only behavioural change this should cause is in
secure mesh mode: with this the station entries will
only be created after the stations are set to AUTH.
Given which drivers support mesh, this seems to not
be a problem.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
(based on Eliad's patch)
Add a callback to notify the low-level driver whenever
the state of a station changes. The driver is only
notified when the station is actually in the mac80211
hash table, not for pre-insert state transitions.
To allow the driver to replace sta_add/remove calls
with this, call extra transitions with the NOTEXIST
state.
This callback can fail, so we need to be careful in
handling it when a station is inserted, particularly
in the IBSS case where we still keep the station entry
around for mac80211 purposes.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Setting keys and updating TKIP keys must use the
BSS sdata (not AP_VLAN), so we translate. Move
the translation into driver-ops wrappers instead
of having it inline in the code to simplify the
normal code flow.
The same can be done for sta_add/remove which
already does the translation in the wrapper.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The driver is never informed about monitor or
AP_VLAN interfaces, so whenever we pass those
to it later this is a bug. Verify we don't as
there are some cases where this could happen.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The flaglock in struct sta_info has long been
something that I wanted to get rid of, this
finally does the conversion to atomic bitops.
The conversion itself is straight-forward in
most places, a few things needed to change a
bit since we can no longer use multiple bits
at the same time.
On x86-64, this is a fairly significant code
size reduction:
text data bss dec hex
427861 23648 1008 452517 6e7a5 before
425383 23648 976 450007 6ddd7 after
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
When suspending with all netdevs down, the device
is stopped but we still call a number of driver
callbacks that the driver might not expect. The
same happens during resume, we might call a few
callbacks without starting the driver. Fix this
by checking open_count around more things and
exiting quickly if it is 0.
Also, while at this I noticed that the coverage
class isn't reprogrammed after resume, so add
that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
If the driver can't support WoWLAN in the current
state, this patch allows it to return 1 from the
suspend callback to do the normal deconfiguration
instead of using suspend/resume calls. Note that
if it does this, resume won't be called.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Cancel all relevant timers/works before suspending (wowlan).
This patch handles the following warning:
WARNING: at net/mac80211/util.c:565 queueing ieee80211 work while going to suspend
Backtrace:
[<bf07b598>] (ieee80211_can_queue_work+0x0/0x4c [mac80211])
[<bf07c28c>] (ieee80211_queue_work+0x0/0x30 [mac80211])
[<bf0690dc>] (ieee80211_sta_timer+0x0/0x3c [mac80211])
[<c00a3008>] (run_timer_softirq+0x0/0x220)
[<c009e530>] (__do_softirq+0x0/0x130)
[<c009e660>] (irq_exit+0x0/0xb4)
[<c004c4a0>] (ipi_timer+0x0/0x4c)
[<c0046350>] (do_local_timer+0x0/0x88)
[<c00488ec>] (cpu_idle+0x0/0xe0)
[<c05294e8>] (rest_init+0x0/0xe0)
[<c0008958>] (start_kernel+0x0/0x314)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This adds basic support for the new WoWLAN
configuration in mac80211. The behaviour is
completely offloaded to the driver though,
with two new callbacks (suspend/resume).
Options for the driver include a complete
reconfiguration after wakeup, and exposing
all the triggers it wants to support.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Currently, the code to tear down BA sessions will
execute after queues are stopped, but attempt to
send frames, so those frames will just get queued,
which isn't intended. Move this code to before to
tear down the sessions properly.
Additionally, after stopping queues, flush the TX
queues in the driver driver to make sure all the
frames went out.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
