summaryrefslogtreecommitdiff
path: root/net/mac80211/ieee80211_i.h
AgeCommit message (Collapse)Author
2017-09-06mac80211: fix deadlock in driver-managed RX BA session startJohannes Berg
When an RX BA session is started by the driver, and it has to tell mac80211 about it, the corresponding bit in tid_rx_manage_offl gets set and the BA session work is scheduled. Upon testing this bit, it will call __ieee80211_start_rx_ba_session(), thus deadlocking as it already holds the ampdu_mlme.mtx, which that acquires again. Fix this by adding ___ieee80211_start_rx_ba_session(), a version of the function that requires the mutex already held. Cc: stable@vger.kernel.org Fixes: 699cb58c8a52 ("mac80211: manage RX BA session offload without SKB queue") Reported-by: Matteo Croce <mcroce@redhat.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-06-15Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller
The conflicts were two cases of overlapping changes in batman-adv and the qed driver. Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-13mac80211: Fix incorrect condition when checking rx timestampAvraham Stern
If the driver reports the rx timestamp at PLCP start, mac80211 can only handle legacy encoding, but the code checks that the encoding is not legacy. Fix this. Fixes: da6a4352e7c8 ("mac80211: separate encoding/bandwidth from flags") Signed-off-by: Avraham Stern <avraham.stern@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-06-08mac80211: manage RX BA session offload without SKB queueJohannes Berg
Instead of using the SKB queue with the fake pkt_type for the offloaded RX BA session management, also handle this with the normal aggregation state machine worker. This also makes the use of this more reliable since it gets rid of the allocation of the fake skb. Combined with the previous patch, this finally allows us to get rid of the pkt_type hack entirely, so do that as well. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-06-08Merge remote-tracking branch 'net-next/master' into mac80211-nextJohannes Berg
This brings in commit 7a7c0a6438b8 ("mac80211: fix TX aggregation start/stop callback race") to allow the follow-up cleanup. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-05-30mac80211: fix TX aggregation start/stop callback raceJohannes Berg
When starting or stopping an aggregation session, one of the steps is that the driver calls back to mac80211 that the start/stop can proceed. This is handled by queueing up a fake SKB and processing it from the normal iface/sdata work. Since this isn't flushed when disassociating, the following race is possible: * associate * start aggregation session * driver callback * disassociate * associate again to the same AP * callback processing runs, leading to a WARN_ON() that the TID hadn't requested aggregation If the second association isn't to the same AP, there would only be a message printed ("Could not find station: <addr>"), but the same race could happen. Fix this by not going the whole detour with a fake SKB etc. but simply looking up the aggregation session in the driver callback, marking it with a START_CB/STOP_CB bit and then scheduling the regular aggregation work that will now process these bits as well. This also simplifies the code and gets rid of the whole problem with allocation failures of said skb, which could have left the session in limbo. Reported-by: Jouni Malinen <j@w1.fi> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-05-24mac80211: mesh: support sending wide bandwidth CSASimon Wunderlich
To support HT and VHT CSA, beacons and action frames must include the corresponding IEs. Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de> [make ieee80211_ie_build_wide_bw_cs() return void] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-05-19mac80211: mesh: Allow following CSA to DFS channels if userspace handles itBenjamin Berg
If userspace has flagged support for DFS earlier, then we can follow CSA to DFS channels. So instead of rejecting the switch, allow it to happen if the flag has been set during mesh setup. Signed-off-by: Benjamin Berg <benjamin@sipsolutions.net> Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-05-19mac80211: mesh: mark channel as unusable if a regulatory MESH CSA is receivedBenjamin Berg
In the Mesh Channel Switch Parameters (8.4.2.105) the reason is specified to WLAN_REASON_MESH_CHAN_REGULATORY in the case that a regulatory limitation was the cause for the switch. This means another station detected a radar event. Mark the channel as unusable if this happens. Signed-off-by: Benjamin Berg <benjamin@sipsolutions.net> [sw: style cleanup, rebase] Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-04-28mac80211: Add support for BSS max idle period elementAvraham Stern
Parse the BSS max idle period element and set the BSS configuration accordingly so the driver can use this information to configure the max idle period and to use protected management frames for keep alive when required. The BSS max idle period element is defined in IEEE802.11-2016, section 9.4.2.79 Signed-off-by: Avraham Stern <avraham.stern@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-04-28mac80211: Fix possible sband related NULL pointer de-referenceMohammed Shafi Shajakhan
Existing API 'ieee80211_get_sdata_band' returns default 2 GHz band even if the channel context configuration is NULL. This crashes for chipsets which support 5 Ghz alone when it tries to access members of 'sband'. Channel context configuration can be NULL in multivif case and when channel switch is in progress (or) when it fails. Fix this by replacing the API 'ieee80211_get_sdata_band' with 'ieee80211_get_sband' which returns a NULL pointer for sband when the channel configuration is NULL. An example scenario is as below: In multivif mode (AP + STA) with drivers like ath10k, when we do a channel switch in the AP vif (which has a number of clients connected) and a STA vif which is connected to some other AP, when the channel switch in AP vif fails, while the STA vifs tries to connect to the other AP, there is a window where the channel context is NULL/invalid and this results in a crash while the clients connected to the AP vif tries to reconnect and this race is very similar to the one investigated by Michal in https://patchwork.kernel.org/patch/3788161/ and this does happens with hardware that supports 5Ghz alone after long hours of testing with continuous channel switch on the AP vif ieee80211 phy0: channel context reservation cannot be finalized because some interfaces aren't switching wlan0: failed to finalize CSA, disconnecting wlan0-1: deauthenticating from 8c:fd:f0:01:54:9c by local choice (Reason: 3=DEAUTH_LEAVING) WARNING: CPU: 1 PID: 19032 at net/mac80211/ieee80211_i.h:1013 sta_info_alloc+0x374/0x3fc [mac80211] [<bf77272c>] (sta_info_alloc [mac80211]) [<bf78776c>] (ieee80211_add_station [mac80211])) [<bf73cc50>] (nl80211_new_station [cfg80211]) Unable to handle kernel NULL pointer dereference at virtual address 00000014 pgd = d5f4c000 Internal error: Oops: 17 [#1] PREEMPT SMP ARM PC is at sta_info_alloc+0x380/0x3fc [mac80211] LR is at sta_info_alloc+0x37c/0x3fc [mac80211] [<bf772738>] (sta_info_alloc [mac80211]) [<bf78776c>] (ieee80211_add_station [mac80211]) [<bf73cc50>] (nl80211_new_station [cfg80211])) Cc: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qti.qualcomm.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-04-28mac80211: separate encoding/bandwidth from flagsJohannes Berg
We currently use a lot of flags that are mutually incompatible, separate this out into actual encoding and bandwidth enum values. Much of this again done with spatch, with manual post-editing, mostly to add the switch statements and get rid of the conversions. @@ expression status; @@ -status->enc_flags |= RX_ENC_FLAG_80MHZ +status->bw = RATE_INFO_BW_80 @@ expression status; @@ -status->enc_flags |= RX_ENC_FLAG_40MHZ +status->bw = RATE_INFO_BW_40 @@ expression status; @@ -status->enc_flags |= RX_ENC_FLAG_20MHZ +status->bw = RATE_INFO_BW_20 @@ expression status; @@ -status->enc_flags |= RX_ENC_FLAG_160MHZ +status->bw = RATE_INFO_BW_160 @@ expression status; @@ -status->enc_flags |= RX_ENC_FLAG_5MHZ +status->bw = RATE_INFO_BW_5 @@ expression status; @@ -status->enc_flags |= RX_ENC_FLAG_10MHZ +status->bw = RATE_INFO_BW_10 @@ expression status; @@ -status->enc_flags |= RX_ENC_FLAG_VHT +status->encoding = RX_ENC_VHT @@ expression status; @@ -status->enc_flags |= RX_ENC_FLAG_HT +status->encoding = RX_ENC_HT @@ expression status; @@ -status.enc_flags |= RX_ENC_FLAG_VHT +status.encoding = RX_ENC_VHT @@ expression status; @@ -status.enc_flags |= RX_ENC_FLAG_HT +status.encoding = RX_ENC_HT @@ expression status; @@ -(status->enc_flags & RX_ENC_FLAG_HT) +(status->encoding == RX_ENC_HT) @@ expression status; @@ -(status->enc_flags & RX_ENC_FLAG_VHT) +(status->encoding == RX_ENC_VHT) @@ expression status; @@ -(status->enc_flags & RX_ENC_FLAG_5MHZ) +(status->bw == RATE_INFO_BW_5) @@ expression status; @@ -(status->enc_flags & RX_ENC_FLAG_10MHZ) +(status->bw == RATE_INFO_BW_10) @@ expression status; @@ -(status->enc_flags & RX_ENC_FLAG_40MHZ) +(status->bw == RATE_INFO_BW_40) @@ expression status; @@ -(status->enc_flags & RX_ENC_FLAG_80MHZ) +(status->bw == RATE_INFO_BW_80) @@ expression status; @@ -(status->enc_flags & RX_ENC_FLAG_160MHZ) +(status->bw == RATE_INFO_BW_160) Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-04-28mac80211: clean up rate encoding bits in RX statusJohannes Berg
In preparation for adding support for HE rates, clean up the driver report encoding for rate/bandwidth reporting on RX frames. Much of this patch was done with the following spatch: @@ expression status; @@ -status->flag & (RX_FLAG_HT | RX_FLAG_VHT) +status->enc_flags & (RX_ENC_FLAG_HT | RX_ENC_FLAG_VHT) @@ assignment operator op; expression status; @@ -status->flag op RX_FLAG_SHORTPRE +status->enc_flags op RX_ENC_FLAG_SHORTPRE @@ expression status; @@ -status->flag & RX_FLAG_SHORTPRE +status->enc_flags & RX_ENC_FLAG_SHORTPRE @@ assignment operator op; expression status; @@ -status->flag op RX_FLAG_HT +status->enc_flags op RX_ENC_FLAG_HT @@ expression status; @@ -status->flag & RX_FLAG_HT +status->enc_flags & RX_ENC_FLAG_HT @@ assignment operator op; expression status; @@ -status->flag op RX_FLAG_40MHZ +status->enc_flags op RX_ENC_FLAG_40MHZ @@ expression status; @@ -status->flag & RX_FLAG_40MHZ +status->enc_flags & RX_ENC_FLAG_40MHZ @@ assignment operator op; expression status; @@ -status->flag op RX_FLAG_SHORT_GI +status->enc_flags op RX_ENC_FLAG_SHORT_GI @@ expression status; @@ -status->flag & RX_FLAG_SHORT_GI +status->enc_flags & RX_ENC_FLAG_SHORT_GI @@ assignment operator op; expression status; @@ -status->flag op RX_FLAG_HT_GF +status->enc_flags op RX_ENC_FLAG_HT_GF @@ expression status; @@ -status->flag & RX_FLAG_HT_GF +status->enc_flags & RX_ENC_FLAG_HT_GF @@ assignment operator op; expression status; @@ -status->flag op RX_FLAG_VHT +status->enc_flags op RX_ENC_FLAG_VHT @@ expression status; @@ -status->flag & RX_FLAG_VHT +status->enc_flags & RX_ENC_FLAG_VHT @@ assignment operator op; expression status; @@ -status->flag op RX_FLAG_STBC_MASK +status->enc_flags op RX_ENC_FLAG_STBC_MASK @@ expression status; @@ -status->flag & RX_FLAG_STBC_MASK +status->enc_flags & RX_ENC_FLAG_STBC_MASK @@ assignment operator op; expression status; @@ -status->flag op RX_FLAG_LDPC +status->enc_flags op RX_ENC_FLAG_LDPC @@ expression status; @@ -status->flag & RX_FLAG_LDPC +status->enc_flags & RX_ENC_FLAG_LDPC @@ assignment operator op; expression status; @@ -status->flag op RX_FLAG_10MHZ +status->enc_flags op RX_ENC_FLAG_10MHZ @@ expression status; @@ -status->flag & RX_FLAG_10MHZ +status->enc_flags & RX_ENC_FLAG_10MHZ @@ assignment operator op; expression status; @@ -status->flag op RX_FLAG_5MHZ +status->enc_flags op RX_ENC_FLAG_5MHZ @@ expression status; @@ -status->flag & RX_FLAG_5MHZ +status->enc_flags & RX_ENC_FLAG_5MHZ @@ assignment operator op; expression status; @@ -status->vht_flag op RX_VHT_FLAG_80MHZ +status->enc_flags op RX_ENC_FLAG_80MHZ @@ expression status; @@ -status->vht_flag & RX_VHT_FLAG_80MHZ +status->enc_flags & RX_ENC_FLAG_80MHZ @@ assignment operator op; expression status; @@ -status->vht_flag op RX_VHT_FLAG_160MHZ +status->enc_flags op RX_ENC_FLAG_160MHZ @@ expression status; @@ -status->vht_flag & RX_VHT_FLAG_160MHZ +status->enc_flags & RX_ENC_FLAG_160MHZ @@ assignment operator op; expression status; @@ -status->vht_flag op RX_VHT_FLAG_BF +status->enc_flags op RX_ENC_FLAG_BF @@ expression status; @@ -status->vht_flag & RX_VHT_FLAG_BF +status->enc_flags & RX_ENC_FLAG_BF @@ assignment operator op; expression status, STBC; @@ -status->flag op STBC << RX_FLAG_STBC_SHIFT +status->enc_flags op STBC << RX_ENC_FLAG_STBC_SHIFT @@ assignment operator op; expression status; @@ -status.flag op RX_FLAG_SHORTPRE +status.enc_flags op RX_ENC_FLAG_SHORTPRE @@ expression status; @@ -status.flag & RX_FLAG_SHORTPRE +status.enc_flags & RX_ENC_FLAG_SHORTPRE @@ assignment operator op; expression status; @@ -status.flag op RX_FLAG_HT +status.enc_flags op RX_ENC_FLAG_HT @@ expression status; @@ -status.flag & RX_FLAG_HT +status.enc_flags & RX_ENC_FLAG_HT @@ assignment operator op; expression status; @@ -status.flag op RX_FLAG_40MHZ +status.enc_flags op RX_ENC_FLAG_40MHZ @@ expression status; @@ -status.flag & RX_FLAG_40MHZ +status.enc_flags & RX_ENC_FLAG_40MHZ @@ assignment operator op; expression status; @@ -status.flag op RX_FLAG_SHORT_GI +status.enc_flags op RX_ENC_FLAG_SHORT_GI @@ expression status; @@ -status.flag & RX_FLAG_SHORT_GI +status.enc_flags & RX_ENC_FLAG_SHORT_GI @@ assignment operator op; expression status; @@ -status.flag op RX_FLAG_HT_GF +status.enc_flags op RX_ENC_FLAG_HT_GF @@ expression status; @@ -status.flag & RX_FLAG_HT_GF +status.enc_flags & RX_ENC_FLAG_HT_GF @@ assignment operator op; expression status; @@ -status.flag op RX_FLAG_VHT +status.enc_flags op RX_ENC_FLAG_VHT @@ expression status; @@ -status.flag & RX_FLAG_VHT +status.enc_flags & RX_ENC_FLAG_VHT @@ assignment operator op; expression status; @@ -status.flag op RX_FLAG_STBC_MASK +status.enc_flags op RX_ENC_FLAG_STBC_MASK @@ expression status; @@ -status.flag & RX_FLAG_STBC_MASK +status.enc_flags & RX_ENC_FLAG_STBC_MASK @@ assignment operator op; expression status; @@ -status.flag op RX_FLAG_LDPC +status.enc_flags op RX_ENC_FLAG_LDPC @@ expression status; @@ -status.flag & RX_FLAG_LDPC +status.enc_flags & RX_ENC_FLAG_LDPC @@ assignment operator op; expression status; @@ -status.flag op RX_FLAG_10MHZ +status.enc_flags op RX_ENC_FLAG_10MHZ @@ expression status; @@ -status.flag & RX_FLAG_10MHZ +status.enc_flags & RX_ENC_FLAG_10MHZ @@ assignment operator op; expression status; @@ -status.flag op RX_FLAG_5MHZ +status.enc_flags op RX_ENC_FLAG_5MHZ @@ expression status; @@ -status.flag & RX_FLAG_5MHZ +status.enc_flags & RX_ENC_FLAG_5MHZ @@ assignment operator op; expression status; @@ -status.vht_flag op RX_VHT_FLAG_80MHZ +status.enc_flags op RX_ENC_FLAG_80MHZ @@ expression status; @@ -status.vht_flag & RX_VHT_FLAG_80MHZ +status.enc_flags & RX_ENC_FLAG_80MHZ @@ assignment operator op; expression status; @@ -status.vht_flag op RX_VHT_FLAG_160MHZ +status.enc_flags op RX_ENC_FLAG_160MHZ @@ expression status; @@ -status.vht_flag & RX_VHT_FLAG_160MHZ +status.enc_flags & RX_ENC_FLAG_160MHZ @@ assignment operator op; expression status; @@ -status.vht_flag op RX_VHT_FLAG_BF +status.enc_flags op RX_ENC_FLAG_BF @@ expression status; @@ -status.vht_flag & RX_VHT_FLAG_BF +status.enc_flags & RX_ENC_FLAG_BF @@ assignment operator op; expression status, STBC; @@ -status.flag op STBC << RX_FLAG_STBC_SHIFT +status.enc_flags op STBC << RX_ENC_FLAG_STBC_SHIFT @@ @@ -RX_FLAG_STBC_SHIFT +RX_ENC_FLAG_STBC_SHIFT Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-04-18mac80211: keep a separate list of monitor interfaces that are upJohannes Berg
In addition to keeping monitor interfaces on the regular list of interfaces, keep those that are up and not in cooked mode on a separate list. This saves having to iterate all interfaces when delivering to monitor interfaces. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-03-02average: change to declare precision, not factorJohannes Berg
Declaring the factor is counter-intuitive, and people are prone to using small(-ish) values even when that makes no sense. Change the DECLARE_EWMA() macro to take the fractional precision, in bits, rather than a factor, and update all users. While at it, add some more documentation. Acked-by: David S. Miller <davem@davemloft.net> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2017-01-14Merge tag 'mac80211-next-for-davem-2017-01-13' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next Johannes Berg says: ==================== For 4.11, we seem to have more than in the past few releases: * socket owner support for connections, so when the wifi manager (e.g. wpa_supplicant) is killed, connections are torn down - wpa_supplicant is critical to managing certain operations, and can opt in to this where applicable * minstrel & minstrel_ht updates to be more efficient (time and space) * set wifi_acked/wifi_acked_valid for skb->destructor use in the kernel, which was already available to userspace * don't indicate new mesh peers that might be used if there's no room to add them * multicast-to-unicast support in mac80211, for better medium usage (since unicast frames can use *much* higher rates, by ~3 orders of magnitude) * add API to read channel (frequency) limitations from DT * add infrastructure to allow randomizing public action frames for MAC address privacy (still requires driver support) * many cleanups and small improvements/fixes across the board ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2016-12-16linux: drop __bitwise__ everywhereMichael S. Tsirkin
__bitwise__ used to mean "yes, please enable sparse checks unconditionally", but now that we dropped __CHECK_ENDIAN__ __bitwise is exactly the same. There aren't many users, replace it by __bitwise everywhere. Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by: Stefan Schmidt <stefan@osg.samsung.com> Acked-by: Krzysztof Kozlowski <krzk@kernel.org> Akced-by: Lee Duncan <lduncan@suse.com>
2016-12-13mac80211: Use appropriate name for functions and messagesMasashi Honma
These functions drifts TSF timers, not TBTT. Signed-off-by: Masashi Honma <masashi.honma@gmail.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2016-12-13mac80211: Remove invalid flag operations in mesh TSF synchronizationMasashi Honma
mesh_sync_offset_adjust_tbtt() implements Extensible synchronization framework ([1] 13.13.2 Extensible synchronization framework). It shall not operate the flag "TBTT Adjusting subfield" ([1] 8.4.2.100.8 Mesh Capability), since it is used only for MBCA ([1] 13.13.4 Mesh beacon collision avoidance, see 13.13.4.4.3 TBTT scanning and adjustment procedures for detail). So this patch remove the flag operations. [1] IEEE Std 802.11 2012 Signed-off-by: Masashi Honma <masashi.honma@gmail.com> [remove adjusting_tbtt entirely, since it's now unused] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2016-12-13mac80211: multicast to unicast conversionMichael Braun
Add the ability for an AP (and associated VLANs) to perform multicast-to-unicast conversion for ARP, IPv4 and IPv6 frames (possibly within 802.1Q). If enabled, such frames are to be sent to each station separately, with the DA replaced by their own MAC address rather than the group address. Note that this may break certain expectations of the receiver, such as the ability to drop unicast IP packets received within multicast L2 frames, or the ability to not send ICMP destination unreachable messages for packets received in L2 multicast (which is required, but the receiver can't tell the difference if this new option is enabled.) This also doesn't implement the 802.11 DMS (directed multicast service). Signed-off-by: Michael Braun <michael-dev@fami-braun.de> [use true/false, rename label to the correct "multicast", use __be16 for ethertype and network order for constants] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2016-10-27mac80211: FILS AEAD protection for station mode association framesJouni Malinen
This adds support for encrypting (Re)Association Request frame and decryption (Re)Association Response frame when using FILS in station mode. Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2016-10-19mac80211: uapsd_queues is in QoS IE orderEmmanuel Grumbach
The uapsd_queue field is in QoS IE order and not in IEEE80211_AC_*'s order. This means that mac80211 would get confused between BK and BE which is certainly not such a big deal but needs to be fixed. Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2016-10-17mac80211: fix A-MSDU outer SA/DAMichael Braun
According to IEEE 802.11-2012 section 8.3.2 table 8-19, the outer SA/DA of A-MSDU frames need to be changed depending on FromDS/ToDS values. Signed-off-by: Michael Braun <michael-dev@fami-braun.de> [use ether_addr_copy and add alignment annotations] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2016-10-12mac80211: filter multicast data packets on AP / AP_VLANMichael Braun
This patch adds filtering for multicast data packets on AP_VLAN interfaces that have no authorized station connected and changes filtering on AP interfaces to not count stations assigned to AP_VLAN interfaces. This saves airtime and avoids waking up other stations currently authorized in this BSS. When using WPA, the packets dropped could not be decrypted by any station. The behaviour when there are no AP_VLAN interfaces is left unchanged. When there are AP_VLAN interfaces, this patch 1. adds filtering multicast data packets sent on AP_VLAN interfaces that have no authorized station connected. No filtering happens on 4addr AP_VLAN interfaces. 2. makes filtering of multicast data packets sent on AP interfaces depend on the number of authorized stations in this bss not assigned to an AP_VLAN interface. Therefore, a new num_mcast_sta counter is added for AP_VLAN interfaces. The existing one for AP interfaces is altered to not track stations assigned to an AP_VLAN interface. The new counter is exposed in debugfs. Signed-off-by: Michael Braun <michael-dev@fami-braun.de> [reformat commit message a bit, unline ieee80211_vif_{inc,dec}_num_mcast] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2016-10-04Merge remote-tracking branch 'net-next/master' into mac80211-nextJohannes Berg
Resolve the merge conflict between Felix's/my and Toke's patches coming into the tree through net and mac80211-next respectively. Most of Felix's changes go away due to Toke's new infrastructure work, my patch changes to "goto begin" (the label wasn't there before) instead of returning NULL so flow control towards drivers is preserved better. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2016-09-30mac80211: Move reorder-sensitive TX handlers to after TXQ dequeueToke Høiland-Jørgensen
The TXQ intermediate queues can cause packet reordering when more than one flow is active to a single station. Since some of the wifi-specific packet handling (notably sequence number and encryption handling) is sensitive to re-ordering, things break if they are applied before the TXQ. This splits up the TX handlers and fast_xmit logic into two parts: An early part and a late part. The former is applied before TXQ enqueue, and the latter after dequeue. The non-TXQ path just applies both parts at once. Because fragments shouldn't be split up or reordered, the fragmentation handler is run after dequeue. Any fragments are then kept in the TXQ and on subsequent dequeues they take precedence over dequeueing from the FQ structure. This approach avoids having to scatter special cases all over the place for when TXQ is enabled, at the cost of making the fast_xmit and TX handler code slightly more complex. Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk> [fix a few code-style nits, make ieee80211_xmit_fast_finish void, remove a useless txq->sta check] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2016-09-30mac80211: Implement add_nan_func and rm_nan_funcAyala Beker
Implement add/rm_nan_func functions and handle NAN function termination notifications. Handle instance_id allocation for NAN functions and implement the reconfig flow. Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2016-09-30mac80211: implement nan_change_confAyala Beker
Implement nan_change_conf callback which allows to change current NAN configuration (master preference and dual band operation). Store the current NAN configuration in sdata, so it can be used both to provide the driver the updated configuration with changes and also it will be used in hw reconfig flows in next patches. Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2016-09-20mac80211: Use rhltable instead of rhashtableHerbert Xu
mac80211 currently uses rhashtable with insecure_elasticity set to true. The latter is because of duplicate objects. What's more, mac80211 walks the rhashtable chains by hand which is broken as rhashtable may contain multiple tables due to resizing or rehashing. This patch fixes it by converting it to the newly added rhltable interface which is designed for use with duplicate objects. With rhltable a lookup returns a list of objects instead of a single one. This is then fed into the existing for_each_sta_info macro. This patch also deletes the sta_addr_hash function since rhashtable defaults to jhash. Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-09-13mac80211: Re-structure aqm debugfs output and keep CoDel stats per txqToke Høiland-Jørgensen
Currently the 'aqm' stats in mac80211 only keeps overlimit drop stats, not CoDel stats. This moves the CoDel stats into the txqi structure to keep them per txq in order to show them in debugfs. In addition, the aqm debugfs output is restructured by splitting it up into three files: One global per phy, one per netdev and one per station, in the appropriate directories. The files are all called aqm, and are only created if the driver supports the wake_tx_queue op (rather than emitting an error on open as previously). Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2016-09-12mac80211: add support for MU-MIMO air snifferAviya Erenfeld
add support to MU-MIMO air sniffer according groupID: in monitor mode, use a given MU-MIMO groupID to monitor stations that belongs to that group using MU-MIMO. add support for following a station according to its MAC address using VHT MU-MIMO sniffer: the monitors wait until they get an action MU-MIMO notification frame, then parses it in order to find the groupID that corresponds to the given MAC address and monitors packets destined to that groupID using VHT MU-MIMO. Signed-off-by: Aviya Erenfeld <aviya.erenfeld@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2016-09-12mac80211: refactor monitor representation in sdataAviya Erenfeld
Insert the u32 monitor flags variable in a new structure that represents a monitor interface. This will allow to add more configuration variables to that structure which will happen in an upcoming change. Signed-off-by: Aviya Erenfeld <aviya.erenfeld@intel.com> Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2016-07-06mac80211: Add support for beacon report radio measurementAvraham Stern
Add the following to support beacon report radio measurement with the measurement mode field set to passive or active: 1. Propagate the required scan duration to the device 2. Report the scan start time (in terms of TSF) 3. Report each BSS's detection time (also in terms of TSF) TSF times refer to the BSS that the interface that requested the scan is connected to. Signed-off-by: Assaf Krauss <assaf.krauss@intel.com> Signed-off-by: Avraham Stern <avraham.stern@intel.com> [changed ath9k/10k, at76c59x-usb, iwlegacy, wl1251 and wlcore to match the new API] Signed-off-by: Luca Coelho <luciano.coelho@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2016-06-09mac80211: implement codel on fair queuing flowsMichal Kazior
There is no other limit other than a global packet count limit when using software queuing. This means a single flow queue can grow insanely long. This is particularly bad for TCP congestion algorithms which requires a little more sophisticated frame dropping scheme than a mere headdrop on limit overflow. Hence apply (a slighly modified, to fit the knobs) CoDel5 on flow queues. This improves TCP convergence and stability when combined with wireless driver which keeps its own tx queue/fifo at a minimum fill level for given link conditions. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2016-06-09mac80211: implement fair queueing per txqMichal Kazior
mac80211's software queues were designed to work very closely with device tx queues. They are required to make use of 802.11 packet aggregation easily and efficiently. Due to the way 802.11 aggregation is designed it only makes sense to keep fair queuing as close to hardware as possible to reduce induced latency and inertia and provide the best flow responsiveness. This change doesn't translate directly to immediate and significant gains. End result depends on driver's induced latency. Best results can be achieved if driver keeps its own tx queue/fifo fill level to a minimum. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2016-06-09mac80211: skip netdev queue control with software queuingMichal Kazior
Qdiscs are designed with no regard to 802.11 aggregation requirements and hand out packet-by-packet with no guarantee they are destined to the same tid. This does more bad than good no matter how fairly a given qdisc may behave on an ethernet interface. Software queuing used per-AC netdev subqueue congestion control whenever a global AC limit was hit. This meant in practice a single station or tid queue could starve others rather easily. This could resonate with qdiscs in a bad way or could just end up with poor aggregation performance. Increasing the AC limit would increase induced latency which is also bad. Disabling qdiscs by default and performing taildrop instead of netdev subqueue congestion control on the other hand makes it possible for tid queues to fill up "in the meantime" while preventing stations starving each other. This increases aggregation opportunities and should allow software queuing based drivers achieve better performance by utilizing airtime more efficiently with big aggregates. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2016-04-12cfg80211: remove enum ieee80211_bandJohannes Berg
This enum is already perfectly aliased to enum nl80211_band, and the only reason for it is that we get IEEE80211_NUM_BANDS out of it. There's no really good reason to not declare the number of bands in nl80211 though, so do that and remove the cfg80211 one. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2016-04-09Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller
2016-04-06mac80211: add A-MSDU tx supportFelix Fietkau
Requires software tx queueing and fast-xmit support. For good performance, drivers need frag_list support as well. This avoids the need for copying data of aggregated frames. Running without it is only supported for debugging purposes. To avoid performance and packet size issues, the rate control module or driver needs to limit the maximum A-MSDU size by setting max_rc_amsdu_len in struct ieee80211_sta. Signed-off-by: Felix Fietkau <nbd@openwrt.org> [fix locking issue] Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2016-04-06mac80211: add fast-rx pathJohannes Berg
The regular RX path has a lot of code, but with a few assumptions on the hardware it's possible to reduce the amount of code significantly. Currently the assumptions on the driver are the following: * hardware/driver reordering buffer (if supporting aggregation) * hardware/driver decryption & PN checking (if using encryption) * hardware/driver did de-duplication * hardware/driver did A-MSDU deaggregation * AP_LINK_PS is used (in AP mode) * no client powersave handling in mac80211 (in client mode) of which some are actually checked per packet: * de-duplication * PN checking * decryption and additionally packets must * not be A-MSDU (have been deaggregated by driver/device) * be data packets * not be fragmented * be unicast * have RFC 1042 header Additionally dynamically we assume: * no encryption or CCMP/GCMP, TKIP/WEP/other not allowed * station must be authorized * 4-addr format not enabled Some data needed for the RX path is cached in a new per-station "fast_rx" structure, so that we only need to look at this and the packet, no other memory when processing packets on the fast RX path. After doing the above per-packet checks, the data path collapses down to a pretty simple conversion function taking advantage of the data cached in the small fast_rx struct. This should speed up the RX processing, and will make it easier to reason about parallelizing RX (for which statistics will need to be per-CPU still.) Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2016-04-05mac80211: mesh: convert path table to rhashtableBob Copeland
In the time since the mesh path table was implemented as an RCU-traversable, dynamically growing hash table, a generic RCU hashtable implementation was added to the kernel. Switch the mesh path table over to rhashtable to remove some code and also gain some features like automatic shrinking. Cc: Thomas Graf <tgraf@suug.ch> Cc: netdev@vger.kernel.org Signed-off-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2016-04-05mac80211: mesh: move path tables into if_meshBob Copeland
The mesh path and mesh gate hashtables are global, containing all of the mpaths for every mesh interface, but the paths are all tied logically to a single interface. The common case is just a single mesh interface, so optimize for that by moving the global hashtable into the per-interface struct. Doing so allows us to drop sdata pointer comparisons inside the lookups and also saves a few bytes of BSS and data. Signed-off-by: Bob Copeland <me@bobcopeland.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2016-04-05mac80211: TDLS: change BW calculation for WIDER_BW peersArik Nemtsov
The previous approach simply ignored chandef restrictions when calculating the appropriate peer BW for a WIDER_BW peer. This could result in a regulatory violation if both peers indicated 80MHz support, but the regdomain forbade it. Change the approach to setting a WIDER_BW peer's BW. Don't exempt it from the chandef width at first. If during TDLS negotiation the chandef width is upgraded, update the peer's BW to match. Fixes: 0fabfaafec3a ("mac80211: upgrade BW of TDLS peers when possible") Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2016-03-08Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller
Several cases of overlapping changes, as well as one instance (vxlan) of a bug fix in 'net' overlapping with code movement in 'net-next'. Signed-off-by: David S. Miller <davem@davemloft.net>
2016-03-01mac80211: check PN correctly for GCMP-encrypted fragmented MPDUsJohannes Berg
Just like for CCMP we need to check that for GCMP the fragments have PNs that increment by one; the spec was updated to fix this security issue and now has the following text: The receiver shall discard MSDUs and MMPDUs whose constituent MPDU PN values are not incrementing in steps of 1. Adapt the code for CCMP to work for GCMP as well, luckily the relevant fields already alias each other so no code duplication is needed (just check the aliasing with BUILD_BUG_ON.) Cc: stable@vger.kernel.org Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2016-02-24mac80211: move MU_MIMO_OWNER flag to ieee80211_vifSara Sharon
Drivers may need to track which vif is using VHT MU-MIMO. Move the flag indicationg the ownership of MU_MIMO to ieee80211_vif. Signed-off-by: Sara Sharon <sara.sharon@intel.com> Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2016-02-24mac80211: change ieee80211_rx_reorder_ready() argumentsJohannes Berg
Clean up ieee80211_rx_reorder_ready() callers by passing the RX TID struct and the index, instead of the frames list. This will make it more extensible as well. While at it, move the inline to rx.c as it's only used there. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2016-02-24mac80211: expose txq queue depth and size to driversMichal Kazior
This will allow drivers to make more educated decisions whether to defer transmission or not. Relying on wake_tx_queue() call count implicitly was not possible because it could be called without queued frame count actually changing on software tx aggregation start/stop code paths. It was also not possible to know how long byte-wise queue was without dequeueing. Signed-off-by: Michal Kazior <michal.kazior@tieto.com> Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2016-02-24mac80211: add RX_FLAG_MACTIME_PLCP_STARTJohannes Berg
The timestamp given by iwlwifi is at the beginning of the frame over the air, at (or during) the SYNC field. Allow such timestamps to be given to mac80211, at least (for now) for frames with non-HT/VHT preambles. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2016-02-24mac80211: refactor HT/VHT to chandef codeJohannes Berg
The station MLME and IBSS/mesh ones use entirely different code for interpreting HT and VHT operation elements. Change the code that interprets them a bit - it now modifies an existing chandef - and use it also in the MLME code. Signed-off-by: Johannes Berg <johannes.berg@intel.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-21 18:48:44 +0000