| Age | Commit message (Collapse) | Author |
|---|
|
The dummy ruleset I used to test the original validation change was broken,
most rules were unreachable and were not tested by mark_source_chains().
In some cases rulesets that used to load in a few seconds now require
several minutes.
sample ruleset that shows the behaviour:
echo "*filter"
for i in $(seq 0 100000);do
printf ":chain_%06x - [0:0]\n" $i
done
for i in $(seq 0 100000);do
printf -- "-A INPUT -j chain_%06x\n" $i
printf -- "-A INPUT -j chain_%06x\n" $i
printf -- "-A INPUT -j chain_%06x\n" $i
done
echo COMMIT
[ pipe result into iptables-restore ]
This ruleset will be about 74mbyte in size, with ~500k searches
though all 500k[1] rule entries. iptables-restore will take forever
(gave up after 10 minutes)
Instead of always searching the entire blob for a match, fill an
array with the start offsets of every single ipt_entry struct,
then do a binary search to check if the jump target is present or not.
After this change ruleset restore times get again close to what one
gets when reverting 36472341017529e (~3 seconds on my workstation).
[1] every user-defined rule gets an implicit RETURN, so we get
300k jumps + 100k userchains + 100k returns -> 500k rule entries
Fixes: 36472341017529e ("netfilter: x_tables: validate targets of jumps")
Reported-by: Jeff Wu <wujiafu@gmail.com>
Tested-by: Jeff Wu <wujiafu@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
In preparation for hardware offloading of ipmr/ip6mr we need an
interface that allows to check (and later update) the age of entries.
Relying on stats alone can show activity but not actual age of the entry,
furthermore when there're tens of thousands of entries a lot of the
hardware implementations only support "hit" bits which are cleared on
read to denote that the entry was active and shouldn't be aged out,
these can then be naturally translated into age timestamp and will be
compatible with the software forwarding age. Using a lastuse entry doesn't
affect performance because the members in that cache line are written to
along with the age.
Since all new users are encouraged to use ipmr via netlink, this is
exported via the RTA_EXPIRES attribute.
Also do a minor local variable declaration style adjustment - arrange them
longest to shortest.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
CC: Roopa Prabhu <roopa@cumulusnetworks.com>
CC: Shrijeet Mukherjee <shm@cumulusnetworks.com>
CC: Satish Ashok <sashok@cumulusnetworks.com>
CC: Donald Sharp <sharpd@cumulusnetworks.com>
CC: David S. Miller <davem@davemloft.net>
CC: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
CC: James Morris <jmorris@namei.org>
CC: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
CC: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If socket filter truncates an udp packet below the length of UDP header
in udpv6_queue_rcv_skb() or udp_queue_rcv_skb(), it will trigger a
BUG_ON in skb_pull_rcsum(). This BUG_ON (and therefore a system crash if
kernel is configured that way) can be easily enforced by an unprivileged
user which was reported as CVE-2016-6162. For a reproducer, see
http://seclists.org/oss-sec/2016/q3/8
Fixes: e6afc8ace6dd ("udp: remove headers from UDP packets before queueing")
Reported-by: Marco Grassi <marco.gra@gmail.com>
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Acked-by: Eric Dumazet <edumazet@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All inet6_netconf_notify_devconf() callers are in process context,
so we can use GFP_KERNEL allocations if we take care of not holding
a rwlock while not needed in ip6mr (we hold RTNL there)
Fixes: d67b8c616b48 ("netconf: advertise mc_forwarding status")
Fixes: f3a1bfb11ccb ("rtnl/ipv6: use netconf msg to advertise forwarding status")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Extend the SIT driver to support MPLS over IPv4. This implementation
extends existing support for IPv6 over IPv4 and IPv4 over IPv4.
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Reviewed-by: Dinan Gunawardena <dinan.gunawardena@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
into next
|
|
Conflicts:
drivers/net/ethernet/mellanox/mlx5/core/en.h
drivers/net/ethernet/mellanox/mlx5/core/en_main.c
drivers/net/usb/r8152.c
All three conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following patchset contains Netfilter updates for net-next,
they are:
1) Don't use userspace datatypes in bridge netfilter code, from
Tobin Harding.
2) Iterate only once over the expectation table when removing the
helper module, instead of once per-netns, from Florian Westphal.
3) Extra sanitization in xt_hook_ops_alloc() to return error in case
we ever pass zero hooks, xt_hook_ops_alloc():
4) Handle NFPROTO_INET from the logging core infrastructure, from
Liping Zhang.
5) Autoload loggers when TRACE target is used from rules, this doesn't
change the behaviour in case the user already selected nfnetlink_log
as preferred way to print tracing logs, also from Liping Zhang.
6) Conntrack slabs with SLAB_HWCACHE_ALIGN to allow rearranging fields
by cache lines, increases the size of entries in 11% per entry.
From Florian Westphal.
7) Skip zone comparison if CONFIG_NF_CONNTRACK_ZONES=n, from Florian.
8) Remove useless defensive check in nf_logger_find_get() from Shivani
Bhardwaj.
9) Remove zone extension as place it in the conntrack object, this is
always include in the hashing and we expect more intensive use of
zones since containers are in place. Also from Florian Westphal.
10) Owner match now works from any namespace, from Eric Bierdeman.
11) Make sure we only reply with TCP reset to TCP traffic from
nf_reject_ipv4, patch from Liping Zhang.
12) Introduce --nflog-size to indicate amount of network packet bytes
that are copied to userspace via log message, from Vishwanath Pai.
This obsoletes --nflog-range that has never worked, it was designed
to achieve this but it has never worked.
13) Introduce generic macros for nf_tables object generation masks.
14) Use generation mask in table, chain and set objects in nf_tables.
This allows fixes interferences with ongoing preparation phase of
the commit protocol and object listings going on at the same time.
This update is introduced in three patches, one per object.
15) Check if the object is active in the next generation for element
deactivation in the rbtree implementation, given that deactivation
happens from the commit phase path we have to observe the future
status of the object.
16) Support for deletion of just added elements in the hash set type.
17) Allow to resize hashtable from /proc entry, not only from the
obscure /sys entry that maps to the module parameter, from Florian
Westphal.
18) Get rid of NFT_BASECHAIN_DISABLED, this code is not exercised
anymore since we tear down the ruleset whenever the netdevice
goes away.
19) Support for matching inverted set lookups, from Arturo Borrero.
20) Simplify the iptables_mangle_hook() by removing a superfluous
extra branch.
21) Introduce ether_addr_equal_masked() and use it from the netfilter
codebase, from Joe Perches.
22) Remove references to "Use netfilter MARK value as routing key"
from the Netfilter Kconfig description given that this toggle
doesn't exists already for 10 years, from Moritz Sichert.
23) Introduce generic NF_INVF() and use it from the xtables codebase,
from Joe Perches.
24) Setting logger to NONE via /proc was not working unless explicit
nul-termination was included in the string. This fixes seems to
leave the former behaviour there, so we don't break backward.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It was first reported and reproduced by Petr (thanks!) in
https://bugzilla.kernel.org/show_bug.cgi?id=119581
free_percpu(rt->rt6i_pcpu) used to always happen in ip6_dst_destroy().
However, after fixing a deadlock bug in
commit 9c7370a166b4 ("ipv6: Fix a potential deadlock when creating pcpu rt"),
free_percpu() is not called before setting non_pcpu_rt->rt6i_pcpu to NULL.
It is worth to note that rt6i_pcpu is protected by table->tb6_lock.
kmemleak somehow did not report it. We nailed it down by
observing the pcpu entries in /proc/vmallocinfo (first suggested
by Hannes, thanks!).
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Fixes: 9c7370a166b4 ("ipv6: Fix a potential deadlock when creating pcpu rt")
Reported-by: Petr Novopashenniy <pety@rusnet.ru>
Tested-by: Petr Novopashenniy <pety@rusnet.ru>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Petr Novopashenniy <pety@rusnet.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
netfilter uses multiple FWINV #defines with identical form that hide a
specific structure variable and dereference it with a invflags member.
$ git grep "#define FWINV"
include/linux/netfilter_bridge/ebtables.h:#define FWINV(bool,invflg) ((bool) ^ !!(info->invflags & invflg))
net/bridge/netfilter/ebtables.c:#define FWINV2(bool, invflg) ((bool) ^ !!(e->invflags & invflg))
net/ipv4/netfilter/arp_tables.c:#define FWINV(bool, invflg) ((bool) ^ !!(arpinfo->invflags & (invflg)))
net/ipv4/netfilter/ip_tables.c:#define FWINV(bool, invflg) ((bool) ^ !!(ipinfo->invflags & (invflg)))
net/ipv6/netfilter/ip6_tables.c:#define FWINV(bool, invflg) ((bool) ^ !!(ip6info->invflags & (invflg)))
net/netfilter/xt_tcpudp.c:#define FWINVTCP(bool, invflg) ((bool) ^ !!(tcpinfo->invflags & (invflg)))
Consolidate these macros into a single NF_INVF macro.
Miscellanea:
o Neaten the alignment around these uses
o A few lines are > 80 columns for intelligibility
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
No need for a special case to handle NF_INET_POST_ROUTING, this is
basically the same handling as for prerouting, input, forward.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Some arches have virtually mapped kernel stacks, or will soon have.
tcp_md5_hash_header() uses an automatic variable to copy tcp header
before mangling th->check and calling crypto function, which might
be problematic on such arches.
David says that using percpu storage is also problematic on non SMP
builds.
Just use kmalloc() to allocate scratch areas.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Several cases of overlapping changes, except the packet scheduler
conflicts which deal with the addition of the free list parameter
to qdisc_enqueue().
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This fixes wrong-interface signaling on 32-bit platforms for entries
created when jiffies > 2^31 + MFC_ASSERT_THRESH.
Signed-off-by: Tom Goff <thomas.goff@ll.mit.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This works in exactly the same way as the CIPSO label cache.
The idea is to allow the lsm to cache the result of a secattr
lookup so that it doesn't need to perform the lookup for
every skbuff.
It introduces two sysctl controls:
calipso_cache_enable - enables/disables the cache.
calipso_cache_bucket_size - sets the size of a cache bucket.
Signed-off-by: Huw Davies <huw@codeweavers.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
|
|
Lengths, checksum and the DOI are checked. Checking of the
level and categories are left for the socket layer.
CRC validation is performed in the calipso module to avoid
unconditionally linking crc_ccitt() into ipv6.
Signed-off-by: Huw Davies <huw@codeweavers.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
|
|
In some cases, the lsm needs to add the label to the skbuff directly.
A NF_INET_LOCAL_OUT IPv6 hook is added to selinux to match the IPv4
behaviour. This allows selinux to label the skbuffs that it requires.
Signed-off-by: Huw Davies <huw@codeweavers.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
|
|
Signed-off-by: Huw Davies <huw@codeweavers.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
|
|
Request sockets need to have a label that takes into account the
incoming connection as well as their parent's label. This is used
for the outgoing SYN-ACK and for their child full-socket.
Signed-off-by: Huw Davies <huw@codeweavers.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
|
|
If set, these will take precedence over the parent's options during
both sending and child creation. If they're not set, the parent's
options (if any) will be used.
This is to allow the security_inet_conn_request() hook to modify the
IPv6 options in just the same way that it already may do for IPv4.
Signed-off-by: Huw Davies <huw@codeweavers.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
|
|
CALIPSO is a hop-by-hop IPv6 option. A lot of this patch is based on
the equivalent CISPO code. The main difference is due to manipulating
the options in the hop-by-hop header.
Signed-off-by: Huw Davies <huw@codeweavers.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
|
|
The functionality is equivalent to ipv6_renew_options() except
that the newopt pointer is in kernel, not user, memory
The kernel memory implementation will be used by the CALIPSO network
labelling engine, which needs to be able to set IPv6 hop-by-hop
options.
Signed-off-by: Huw Davies <huw@codeweavers.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
|
|
Remove a specified DOI through the NLBL_CALIPSO_C_REMOVE command.
It requires the attribute:
NLBL_CALIPSO_A_DOI.
Signed-off-by: Huw Davies <huw@codeweavers.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
|
|
Enumerate the DOI list through the NLBL_CALIPSO_C_LISTALL command.
It takes no attributes.
Signed-off-by: Huw Davies <huw@codeweavers.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
|
|
Query a specified DOI through the NLBL_CALIPSO_C_LIST command.
It requires the attribute:
NLBL_CALIPSO_A_DOI.
The reply will contain:
NLBL_CALIPSO_A_MTYPE
Signed-off-by: Huw Davies <huw@codeweavers.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
|
|
CALIPSO is a packet labelling protocol for IPv6 which is very similar
to CIPSO. It is specified in RFC 5570. Much of the code is based on
the current CIPSO code.
This adds support for adding passthrough-type CALIPSO DOIs through the
NLBL_CALIPSO_C_ADD command. It requires attributes:
NLBL_CALIPSO_A_TYPE which must be CALIPSO_MAP_PASS.
NLBL_CALIPSO_A_DOI.
In passthrough mode the CALIPSO engine will map MLS secattr levels
and categories directly to the packet label.
At this stage, the major difference between this and the CIPSO
code is that IPv6 may be compiled as a module. To allow for
this the CALIPSO functions are registered at module init time.
Signed-off-by: Huw Davies <huw@codeweavers.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
|
|
with the commit 8c14586fc320 ("net: ipv6: Use passed in table for
nexthop lookups"), net hop lookup is first performed on route creation
in the passed-in table.
However device match is not enforced in table lookup, so the found
route can be later discarded due to egress device mismatch and no
global lookup will be performed.
This cause the following to fail:
ip link add dummy1 type dummy
ip link add dummy2 type dummy
ip link set dummy1 up
ip link set dummy2 up
ip route add 2001:db8:8086::/48 dev dummy1 metric 20
ip route add 2001:db8:d34d::/64 via 2001:db8:8086::2 dev dummy1 metric 20
ip route add 2001:db8:8086::/48 dev dummy2 metric 21
ip route add 2001:db8:d34d::/64 via 2001:db8:8086::2 dev dummy2 metric 21
RTNETLINK answers: No route to host
This change fixes the issue enforcing device lookup in
ip6_nh_lookup_table()
v1->v2: updated commit message title
Fixes: 8c14586fc320 ("net: ipv6: Use passed in table for nexthop lookups")
Reported-and-tested-by: Beniamino Galvani <bgalvani@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When receiving an ICMPv4 message containing extensions as
defined in RFC 4884, and translating it to ICMPv6 at SIT
or GRE tunnel, we need some extra manipulation in order
to properly forward the extensions.
This patch only takes care of Time Exceeded messages as they
are the ones that typically carry information from various
routers in a fabric during a traceroute session.
It also avoids complex skb logic if the data_len is not
a multiple of 8.
RFC states :
The "original datagram" field MUST contain at least 128 octets.
If the original datagram did not contain 128 octets, the
"original datagram" field MUST be zero padded to 128 octets.
In practice routers use 128 bytes of original datagram, not more.
Initial translation was added in commit ca15a078bd90
("sit: generate icmpv6 error when receiving icmpv4 error")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Oussama Ghorbel <ghorbel@pivasoftware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For better traceroute/mtr support for SIT and GRE tunnels,
we translate IPV4 ICMP ICMP_TIME_EXCEEDED to ICMPV6_TIME_EXCEED
We also have to translate the IPv4 source IP address of ICMP
message to IPv6 v4mapped.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We want to use this helper from GRE as well, so this is
the time to move it in net/ipv6/icmp.c
Also add a @nhs parameter, since SIT and GRE have different
values for the header(s) to skip.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
SIT or GRE tunnels might want to translate an IPV4 address
into a v4mapped one when translating ICMP to ICMPv6.
This patch adds the parameter to icmp6_send() but
does not change icmpv6_send() signature.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IPv6 version of 3f2fb9a834cb ("net: l3mdev: address selection should only
consider devices in L3 domain") and the follow up commit, a17b693cdd876
("net: l3mdev: prefer VRF master for source address selection").
That is, if outbound device is given then the address preference order
is an address from that device, an address from the master device if it
is enslaved, and then an address from a device in the same L3 domain.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IPv6 source address selection needs to consider the real egress route.
Similar to IPv4 implement a get_saddr6 method which is called if
source address has not been set. The get_saddr6 method does a full
lookup which means pulling a route from the VRF FIB table and properly
considering linklocal/multicast destination addresses. Lookup failures
(eg., unreachable) then cause the source address selection to fail
which gets propagated back to the caller.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
VRF driver needs access to ip6_route_get_saddr code. Since it does
little beyond ipv6_dev_get_saddr and ipv6_dev_get_saddr is already
exported for modules move ip6_route_get_saddr to the header as an
inline.
Code move only; no functional change.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Modern C standards expect the '__inline__' keyword to come before the return
type in a declaration, and we get a couple of warnings for this with "make W=1"
in the xfrm{4,6}_policy.c files:
net/ipv6/xfrm6_policy.c:369:1: error: 'inline' is not at beginning of declaration [-Werror=old-style-declaration]
static int inline xfrm6_net_sysctl_init(struct net *net)
net/ipv6/xfrm6_policy.c:374:1: error: 'inline' is not at beginning of declaration [-Werror=old-style-declaration]
static void inline xfrm6_net_sysctl_exit(struct net *net)
net/ipv4/xfrm4_policy.c:339:1: error: 'inline' is not at beginning of declaration [-Werror=old-style-declaration]
static int inline xfrm4_net_sysctl_init(struct net *net)
net/ipv4/xfrm4_policy.c:344:1: error: 'inline' is not at beginning of declaration [-Werror=old-style-declaration]
static void inline xfrm4_net_sysctl_exit(struct net *net)
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since 32b8a8e59c9c ("sit: add IPv4 over IPv4 support")
ipip6_err() may be called for packets whose IP protocol is
IPPROTO_IPIP as well as those whose IP protocol is IPPROTO_IPV6.
In the case of IPPROTO_IPIP packets the correct protocol value is not
passed to ipv4_update_pmtu() or ipv4_redirect().
This patch resolves this problem by using the IP protocol of the packet
rather than a hard-coded value. This appears to be consistent
with the usage of the protocol of a packet by icmp_socket_deliver()
the caller of ipip6_err().
I was able to exercise the redirect case by using a setup where an ICMP
redirect was received for the destination of the encapsulated packet.
However, it appears that although incorrect the protocol field is not used
in this case and thus no problem manifests. On inspection it does not
appear that a problem will manifest in the fragmentation needed/update pmtu
case either.
In short I believe this is a cosmetic fix. None the less, the use of
IPPROTO_IPV6 seems wrong and confusing.
Reviewed-by: Dinan Gunawardena <dinan.gunawardena@netronome.com>
Signed-off-by: Simon Horman <simon.horman@netronome.com>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
1) gre_parse_header() can be called from gre_err()
At this point transport header points to ICMP header, not the inner
header.
2) We can not really change transport header as ipgre_err() will later
assume transport header still points to ICMP header (using icmp_hdr())
3) pskb_may_pull() logic in gre_parse_header() really works
if we are interested at zone pointed by skb->data
4) As Jiri explained in commit b7f8fe251e46 ("gre: do not pull header in
ICMP error processing") we should not pull headers in error handler.
So this fix :
A) changes gre_parse_header() to use skb->data instead of
skb_transport_header()
B) Adds a nhs parameter to gre_parse_header() so that we can skip the
not pulled IP header from error path.
This offset is 0 for normal receive path.
C) remove obsolete IPV6 includes
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tom Herbert <tom@herbertland.com>
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The algorithm for checksum neutral mapping is incorrect. This problem
was being hidden since we were previously always performing checksum
offload on the translated addresses and only with IPv6 HW csum.
Enabling an ILA router shows the issue.
Corrected algorithm:
old_loc is the original locator in the packet, new_loc is the value
to overwrite with and is found in the lookup table. old_flag is
the old flag value (zero of CSUM_NEUTRAL_FLAG) and new_flag is
then (old_flag ^ CSUM_NEUTRAL_FLAG) & CSUM_NEUTRAL_FLAG.
Need SUM(new_id + new_flag + diff) == SUM(old_id + old_flag) for
checksum neutral translation.
Solving for diff gives:
diff = (old_id - new_id) + (old_flag - new_flag)
compute_csum_diff8(new_id, old_id) gives old_id - new_id
If old_flag is set
old_flag - new_flag = old_flag = CSUM_NEUTRAL_FLAG
Else
old_flag - new_flag = -new_flag = ~CSUM_NEUTRAL_FLAG
Tested:
- Implemented a user space program that creates random addresses
and random locators to overwrite. Compares the checksum over
the address before and after translation (must always be equal)
- Enabled ILA router and showed proper operation.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch exports some neighbour discovery functions which can be used
by 6lowpan neighbour discovery ops functionality then.
Cc: David S. Miller <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: James Morris <jmorris@namei.org>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Patrick McHardy <kaber@trash.net>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch introduces neighbour discovery ops callback structure. The
idea is to separate the handling for 6LoWPAN into the 6lowpan module.
These callback offers 6lowpan different handling, such as 802.15.4 short
address handling or RFC6775 (Neighbor Discovery Optimization for IPv6
over 6LoWPANs).
Cc: David S. Miller <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: James Morris <jmorris@namei.org>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Patrick McHardy <kaber@trash.net>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch moves the functionality to add a RA PIO prefix generated
address in an own function. This move prepares to add a hook for
adding a second address for a second link-layer address. E.g. short
address for 802.15.4 6LoWPAN.
Cc: David S. Miller <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: James Morris <jmorris@namei.org>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Patrick McHardy <kaber@trash.net>
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds __ndisc_fill_addr_option as low-level function for
ndisc_fill_addr_option which doesn't depend on net_device parameter.
Cc: David S. Miller <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: James Morris <jmorris@namei.org>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Patrick McHardy <kaber@trash.net>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the autoconfiguration if a valid 802.15.4 short address
is available for 802.15.4 6LoWPAN interfaces.
Cc: David S. Miller <davem@davemloft.net>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: James Morris <jmorris@namei.org>
Cc: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Cc: Patrick McHardy <kaber@trash.net>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Reviewed-by: Stefan Schmidt <stefan@osg.samsung.com>
Signed-off-by: Alexander Aring <aar@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IPv6 multicast and link-local addresses require special handling by the
VRF driver:
1. Rather than using the VRF device index and full FIB lookups,
packets to/from these addresses should use direct FIB lookups based on
the VRF device table.
2. fail sends/receives on a VRF device to/from a multicast address
(e.g, make ping6 ff02::1%<vrf> fail)
3. move the setting of the flow oif to the first dst lookup and revert
the change in icmpv6_echo_reply made in ca254490c8dfd ("net: Add VRF
support to IPv6 stack"). Linklocal/mcast addresses require use of the
skb->dev.
With this change connections into and out of a VRF enslaved device work
for multicast and link-local addresses work (icmp, tcp, and udp)
e.g.,
1. packets into VM with VRF config:
ping6 -c3 fe80::e0:f9ff:fe1c:b974%br1
ping6 -c3 ff02::1%br1
ssh -6 fe80::e0:f9ff:fe1c:b974%br1
2. packets going out a VRF enslaved device:
ping6 -c3 fe80::18f8:83ff:fe4b:7a2e%eth1
ping6 -c3 ff02::1%eth1
ssh -6 root@fe80::18f8:83ff:fe4b:7a2e%eth1
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
L3 master devices are virtual devices similar to the loopback
device. Link local and multicast routes for these devices do
not make sense. The ipv6 addrconf code already skips adding a
linklocal address; do the same for the mcast route.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a corner case in which udp packets belonging to a same
flow are hashed to different socket when hslot->count changes from 10
to 11:
1) When hslot->count <= 10, __udp_lib_lookup() searches udp_table->hash,
and always passes 'daddr' to udp_ehashfn().
2) When hslot->count > 10, __udp_lib_lookup() searches udp_table->hash2,
but may pass 'INADDR_ANY' to udp_ehashfn() if the sockets are bound to
INADDR_ANY instead of some specific addr.
That means when hslot->count changes from 10 to 11, the hash calculated by
udp_ehashfn() is also changed, and the udp packets belonging to a same
flow will be hashed to different socket.
This is easily reproduced:
1) Create 10 udp sockets and bind all of them to 0.0.0.0:40000.
2) From the same host send udp packets to 127.0.0.1:40000, record the
socket index which receives the packets.
3) Create 1 more udp socket and bind it to 0.0.0.0:44096. The number 44096
is 40000 + UDP_HASH_SIZE(4096), this makes the new socket put into the
same hslot as the aformentioned 10 sockets, and makes the hslot->count
change from 10 to 11.
4) From the same host send udp packets to 127.0.0.1:40000, and the socket
index which receives the packets will be different from the one received
in step 2.
This should not happen as the socket bound to 0.0.0.0:44096 should not
change the behavior of the sockets bound to 0.0.0.0:40000.
It's the same case for IPv6, and this patch also fixes that.
Signed-off-by: Su, Xuemin <suxm@chinanetcenter.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cc: Tom Herbert <tom@herbertland.com>
Fixes: 4068579e1e098fa ("net: Implmement RFC 6936 (zero RX csums for UDP/IPv6")
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cc: Florent Fourcot <florent.fourcot@enst-bretagne.fr>
Fixes: 1d13a96c74fc ("ipv6: tcp: fix flowlabel value in ACK messages send from TIME_WAIT")
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IPv6 ping socket error handler doesn't correctly convert the new 32 bit
mtu to host endianness before using.
Cc: Lorenzo Colitti <lorenzo@google.com>
Fixes: 6d0bfe22611602f ("net: ipv6: Add IPv6 support to the ping socket.")
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: Lorenzo Colitti <lorenzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In IPv6 the ToS values are part of the flowlabel in flowi6 and get
extracted during fib rule lookup, but we forgot to correctly initialize
the flowlabel before the routing lookup.
Reported-by: <liam.mcbirnie@boeing.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
