| Age | Commit message (Collapse) | Author |
|---|
|
An interface changing type may not have IPv6 addresses. Don't
call the address configuration type change in this case.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/ethernet/renesas/ravb_main.c
kernel/bpf/syscall.c
net/ipv4/ipmr.c
All three conflicts were cases of overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Setting a value bigger than 255 resulted in using only the lower eight
bits of that value as it is assigned to the u8 header field. To avoid
this unexpected result, reject such values.
Setting a value of zero is technically possible, but hosts receiving
such a packet have to treat it like hop_limit was set to one, according
to RFC2460. Therefore I don't see a use-case for that.
Setting a route's hop_limit to zero in iproute2 means to use the sysctl
default, which is not the case here: Setting e.g.
net.conf.eth0.hop_limit=0 will not make the kernel use
net.conf.all.hop_limit for outgoing packets on eth0. To avoid these
kinds of confusion, reject zero.
Signed-off-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While testing the np->opt RCU conversion, I found that UDP/IPv6 was
using a mixture of xchg() and sk_dst_lock to protect concurrent changes
to sk->sk_dst_cache, leading to possible corruptions and crashes.
ip6_sk_dst_lookup_flow() uses sk_dst_check() anyway, so the simplest
way to fix the mess is to remove sk_dst_lock completely, as we did for
IPv4.
__ip6_dst_store() and ip6_dst_store() share same implementation.
sk_setup_caps() being called with socket lock being held or not,
we have to use sk_dst_set() instead of __sk_dst_set()
Note that I had to move the "np->dst_cookie = rt6_get_cookie(rt);"
in ip6_dst_store() before the sk_setup_caps(sk, dst) call.
This is because ip6_dst_store() can be called from process context,
without any lock held.
As soon as the dst is installed in sk->sk_dst_cache, dst can be freed
from another cpu doing a concurrent ip6_dst_store()
Doing the dst dereference before doing the install is needed to make
sure no use after free would trigger.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If tcp_send_ack() can not allocate skb, we properly handle this
and setup a timer to try later.
Use __GFP_NOWARN to avoid polluting syslog in the case host is
under memory pressure, so that pertinent messages are not lost under
a flood of useless information.
sk_gfp_atomic() can use its gfp_mask argument (all callers currently
were using GFP_ATOMIC before this patch)
We rename sk_gfp_atomic() to sk_gfp_mask() to clearly express this
function now takes into account its second argument (gfp_mask)
Note that when tcp_transmit_skb() is called with clone_it set to false,
we do not attempt memory allocations, so can pass a 0 gfp_mask, which
most compilers can emit faster than a non zero or constant value.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch addresses multiple problems :
UDP/RAW sendmsg() need to get a stable struct ipv6_txoptions
while socket is not locked : Other threads can change np->opt
concurrently. Dmitry posted a syzkaller
(http://github.com/google/syzkaller) program desmonstrating
use-after-free.
Starting with TCP/DCCP lockless listeners, tcp_v6_syn_recv_sock()
and dccp_v6_request_recv_sock() also need to use RCU protection
to dereference np->opt once (before calling ipv6_dup_options())
This patch adds full RCU protection to np->opt
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit ab450605b35caa768ca33e86db9403229bf42be4.
In IPv6, we cannot inherit the dst of the original dst. ndisc packets
are IPv6 packets and may take another route than the original packet.
This patch breaks the following scenario: a packet comes from eth0 and
is forwarded through vxlan1. The encapsulated packet triggers an NS
which cannot be sent because of the wrong route.
CC: Jiri Benc <jbenc@redhat.com>
CC: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It looks like many files are including mroute.h unnecessarily, so remove
the include. Most importantly remove it from ipv6.
CC: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
CC: Steffen Klassert <steffen.klassert@secunet.com>
CC: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since (at least) commit b17a7c179dd3 ("[NET]: Do sysfs registration as
part of register_netdevice."), netdev_run_todo() deals only with
unregistration, so we don't need to do the rtnl_unlock/lock cycle to
finish registration when failing pimreg or dvmrp device creation. In
fact that opens a race condition where someone can delete the device
while rtnl is unlocked because it's fully registered. The problem gets
worse when netlink support is introduced as there are more points of entry
that can cause it and it also makes reusing that code correctly impossible.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If a fragmented multicast packet is received on an ethernet device which
has an active macvlan on top of it, each fragment is duplicated and
received both on the underlying device and the macvlan. If some
fragments for macvlan are processed before the whole packet for the
underlying device is reassembled, the "overlapping fragments" test in
ip6_frag_queue() discards the whole fragment queue.
To resolve this, add device ifindex to the search key and require it to
match reassembling multicast packets and packets to link-local
addresses.
Note: similar patch has been already submitted by Yoshifuji Hideaki in
http://patchwork.ozlabs.org/patch/220979/
but got lost and forgotten for some reason.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Similar to ipv4, when destroying an mrt table the static mfc entries and
the static devices are kept, which leads to devices that can never be
destroyed (because of refcnt taken) and leaked memory. Make sure that
everything is cleaned up on netns destruction.
Fixes: 8229efdaef1e ("netns: ip6mr: enable namespace support in ipv6 multicast forwarding code")
CC: Benjamin Thery <benjamin.thery@bull.net>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add tracepoint to show fib6 table lookups and result.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
the commit cdf3464e6c6b ("ipv6: Fix dst_entry refcnt bugs in ip6_tunnel")
introduced percpu storage for ip6_tunnel dst cache, but while clearing
such cache it used raw_cpu_ptr to walk the per cpu entries, so cached
dst on non current cpu are not actually reset.
This patch replaces raw_cpu_ptr with per_cpu_ptr, properly cleaning
such storage.
Fixes: cdf3464e6c6b ("ipv6: Fix dst_entry refcnt bugs in ip6_tunnel")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
the OUTMCAST stat is double incremented, getting bumped once in the mcast code
itself, and again in the common ip output path. Remove the mcast bump, as its
not needed
Validated by the reporter, with good results
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Reported-by: Claus Jensen <claus.jensen@microsemi.com>
CC: Claus Jensen <claus.jensen@microsemi.com>
CC: David Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some functions access TCP sockets without holding a lock and
might output non consistent data, depending on compiler and or
architecture.
tcp_diag_get_info(), tcp_get_info(), tcp_poll(), get_tcp4_sock() ...
Introduce sk_state_load() and sk_state_store() to fix the issues,
and more clearly document where this lack of locking is happening.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All DST_NOCACHE rt6_info used to have rt->dst.from set to
its parent.
After commit 8e3d5be73681 ("ipv6: Avoid double dst_free"),
DST_NOCACHE is also set to rt6_info which does not have
a parent (i.e. rt->dst.from is NULL).
This patch catches the rt->dst.from == NULL case.
Fixes: 8e3d5be73681 ("ipv6: Avoid double dst_free")
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since the expires of the DST_NOCACHE rt can be set during
the ip6_rt_update_pmtu(), we also need to consider the expires
value when doing ip6_dst_check().
This patches creates __rt6_check_expired() to only
check the expire value (if one exists) of the current rt.
In rt6_dst_from_check(), it adds __rt6_check_expired() as
one of the condition check.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The original bug report:
https://bugzilla.redhat.com/show_bug.cgi?id=1272571
The setup has a IPv4 GRE tunnel running in a IPSec. The bug
happens when ndisc starts sending router solicitation at the gre
interface. The simplified oops stack is like:
__lock_acquire+0x1b2/0x1c30
lock_acquire+0xb9/0x140
_raw_write_lock_bh+0x3f/0x50
__ip6_ins_rt+0x2e/0x60
ip6_ins_rt+0x49/0x50
~~~~~~~~
__ip6_rt_update_pmtu.part.54+0x145/0x250
ip6_rt_update_pmtu+0x2e/0x40
~~~~~~~~
ip_tunnel_xmit+0x1f1/0xf40
__gre_xmit+0x7a/0x90
ipgre_xmit+0x15a/0x220
dev_hard_start_xmit+0x2bd/0x480
__dev_queue_xmit+0x696/0x730
dev_queue_xmit+0x10/0x20
neigh_direct_output+0x11/0x20
ip6_finish_output2+0x21f/0x770
ip6_finish_output+0xa7/0x1d0
ip6_output+0x56/0x190
~~~~~~~~
ndisc_send_skb+0x1d9/0x400
ndisc_send_rs+0x88/0xc0
~~~~~~~~
The rt passed to ip6_rt_update_pmtu() is created by
icmp6_dst_alloc() and it is not managed by the fib6 tree,
so its rt6i_table == NULL. When __ip6_rt_update_pmtu() creates
a RTF_CACHE clone, the newly created clone also has rt6i_table == NULL
and it causes the ip6_ins_rt() oops.
During pmtu update, we only want to create a RTF_CACHE clone
from a rt which is currently managed (or owned) by the
fib6 tree. It means either rt->rt6i_node != NULL or
rt is a RTF_PCPU clone.
It is worth to note that rt6i_table may not be NULL even it is
not (yet) managed by the fib6 tree (e.g. addrconf_dst_alloc()).
Hence, rt6i_node is a better check instead of rt6i_table.
Fixes: 45e4fd26683c ("ipv6: Only create RTF_CACHE routes after encountering pmtu")
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Reported-by: Chris Siebenmann <cks-rhbugzilla@cs.toronto.edu>
Cc: Chris Siebenmann <cks-rhbugzilla@cs.toronto.edu>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I mistakenly took wrong request sock pointer when calling tcp_move_syn()
@req_unhash is either a copy of @req, or a NULL value for
FastOpen connexions (as we do not expect to unhash the temporary
request sock from ehash table)
Fixes: 805c4bc05705 ("tcp: fix req->saved_syn race")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ying Cai <ycai@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For the reasons explained in commit ce1050089c96 ("tcp/dccp: fix
ireq->pktopts race"), we need to make sure we do not access
req->saved_syn unless we own the request sock.
This fixes races for listeners using TCP_SAVE_SYN option.
Fixes: e994b2f0fb92 ("tcp: do not lock listener to process SYN packets")
Fixes: 079096f103fa ("tcp/dccp: install syn_recv requests into ehash table")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Ying Cai <ycai@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In ipv6_add_dev, when addrconf_sysctl_register fails, we do not clean up
the dev_snmp6 entry that we have already registered for this device.
Call snmp6_unregister_dev in this case.
Fixes: a317a2f19da7d ("ipv6: fail early when creating netdev named all or default")
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Minor overlapping changes in net/ipv4/ipmr.c, in 'net' we were
fixing the "BH-ness" of the counter bumps whilst in 'net-next'
the functions were modified to take an explicit 'net' parameter.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Both tunnel6_protocol and tunnel46_protocol share the same error
handler, tunnel6_err(), which traverses through tunnel6_handlers list.
For ipip6 tunnels, we need to traverse tunnel46_handlers as we do e.g.
in tunnel46_rcv(). Current code can generate an ICMPv6 error message
with an IPv4 packet embedded in it.
Fixes: 73d605d1abbd ("[IPSEC]: changing API of xfrm6_tunnel_register")
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
sit0 device allocates its percpu storage twice :
- One time in ipip6_tunnel_init()
- One time in ipip6_fb_tunnel_init()
Thus we leak 48 bytes per possible cpu per network namespace dismantle.
ipip6_fb_tunnel_init() can be much simpler and does not
return an error, and should be called after register_netdev()
Note that ipip6_tunnel_clone_6rd() also needs to be called
after register_netdev() (calling ipip6_tunnel_init())
Fixes: ebe084aafb7e ("sit: Use ipip6_tunnel_init as the ndo_init function.")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes following problems :
1) percpu_counter_init() can return an error, therefore
init_frag_mem_limit() must propagate this error so that
inet_frags_init_net() can do the same up to its callers.
2) If ip[46]_frags_ns_ctl_register() fail, we must unwind
properly and free the percpu_counter.
Without this fix, we leave freed object in percpu_counters
global list (if CONFIG_HOTPLUG_CPU) leading to crashes.
This bug was detected by KASAN and syzkaller tool
(http://github.com/google/syzkaller)
Fixes: 6d7b857d541e ("net: use lib/percpu_counter API for fragmentation mem accounting")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are other error values besides ip6_null_entry that can be returned by
ip6_route_redirect(): fib6_rule_action() can also result in
ip6_blk_hole_entry and ip6_prohibit_entry if such ip rules are installed.
Only checking for ip6_null_entry in rt6_do_redirect() causes ip6_ins_rt()
to be called with rt->rt6i_table == NULL in these cases, making the kernel
crash.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IPv6 request sockets store a pointer to skb containing the SYN packet
to be able to transfer it to full blown socket when 3WHS is done
(ireq->pktopts -> np->pktoptions)
As explained in commit 5e0724d027f0 ("tcp/dccp: fix hashdance race for
passive sessions"), we must transfer the skb only if we won the
hashdance race, if multiple cpus receive the 'ack' packet completing
3WHS at the same time.
Fixes: e994b2f0fb92 ("tcp: do not lock listener to process SYN packets")
Fixes: 079096f103fa ("tcp/dccp: install syn_recv requests into ehash table")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
CHECKSUM_PARTIAL skbs should never arrive in ip_fragment. If we get one
of those warn about them once and handle them gracefully by recalculating
the checksum.
Fixes: commit 32dce968dd987 ("ipv6: Allow for partial checksums on non-ufo packets")
See-also: commit 72e843bb09d45 ("ipv6: ip6_fragment() should check CHECKSUM_PARTIAL")
Cc: Eric Dumazet <edumazet@google.com>
Cc: Vlad Yasevich <vyasevich@gmail.com>
Cc: Benjamin Coddington <bcodding@redhat.com>
Cc: Tom Herbert <tom@herbertland.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We cannot reliable calculate packet size on MSG_MORE corked sockets
and thus cannot decide if they are going to be fragmented later on,
so better not use CHECKSUM_PARTIAL in the first place.
The IPv6 code also intended to protect and not use CHECKSUM_PARTIAL in
the existence of IPv6 extension headers, but the condition was wrong. Fix
it up, too. Also the condition to check whether the packet fits into
one fragment was wrong and has been corrected.
Fixes: commit 32dce968dd987 ("ipv6: Allow for partial checksums on non-ufo packets")
See-also: commit 72e843bb09d45 ("ipv6: ip6_fragment() should check CHECKSUM_PARTIAL")
Cc: Eric Dumazet <edumazet@google.com>
Cc: Vlad Yasevich <vyasevich@gmail.com>
Cc: Benjamin Coddington <bcodding@redhat.com>
Cc: Tom Herbert <tom@herbertland.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec-next
Steffen Klassert says:
====================
pull request (net-next): ipsec-next 2015-10-30
1) The flow cache is limited by the flow cache limit which
depends on the number of cpus and the xfrm garbage collector
threshold which is independent of the number of cpus. This
leads to the fact that on systems with more than 16 cpus
we hit the xfrm garbage collector limit and refuse new
allocations, so new flows are dropped. On systems with 16
or less cpus, we hit the flowcache limit. In this case, we
shrink the flow cache instead of refusing new flows.
We increase the xfrm garbage collector threshold to INT_MAX
to get the same behaviour, independent of the number of cpus.
2) Fix some unaligned accesses on sparc systems.
From Sowmini Varadhan.
3) Fix some header checks in _decode_session4. We may call
pskb_may_pull with a negative value converted to unsigened
int from pskb_may_pull. This can lead to incorrect policy
lookups. We fix this by a check of the data pointer position
before we call pskb_may_pull.
4) Reload skb header pointers after calling pskb_may_pull
in _decode_session4 as this may change the pointers into
the packet.
5) Add a missing statistic counter on inner mode errors.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This change makes it so that we reinitialize the interface if the MTU is
increased back above IPV6_MIN_MTU and the interface is up.
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
issues
Raw sockets with hdrincl enabled can insert ipv6 extension headers
right into the data stream. In case we need to fragment those packets,
we reparse the options header to find the place where we can insert
the fragment header. If the extension headers exceed the link's MTU we
actually cannot make progress in such a case.
Instead of ending up in broken arithmetic or rounding towards 0 and
entering an endless loop in ip6_fragment, just prevent those cases by
aborting early and signal -EMSGSIZE to user space.
This is the second version of the patch which doesn't use the
overflow_usub function, which got reverted for now.
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Linus dislikes these changes. To not hold up the net-merge let's revert
it for now and fix the bug like Linus suggested.
This reverts commit ec3661b42257d9a06cf0d318175623ac7a660113, reversing
changes made to c80dbe04612986fd6104b4a1be21681b113b5ac9.
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is needed in openvswitch to fix an skb leak in the next patch.
Signed-off-by: Joe Stringer <joestringer@nicira.com>
Acked-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Messages like "icmp6_send: no reply to icmp error" are close
to useless. Adding source and destination addresses to provide
some more clue.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
net/ipv6/xfrm6_output.c
net/openvswitch/flow_netlink.c
net/openvswitch/vport-gre.c
net/openvswitch/vport-vxlan.c
net/openvswitch/vport.c
net/openvswitch/vport.h
The openvswitch conflicts were overlapping changes. One was
the egress tunnel info fix in 'net' and the other was the
vport ->send() op simplification in 'net-next'.
The xfrm6_output.c conflicts was also a simplification
overlapping a bug fix.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Multiple cpus can process duplicates of incoming ACK messages
matching a SYN_RECV request socket. This is a rare event under
normal operations, but definitely can happen.
Only one must win the race, otherwise corruption would occur.
To fix this without adding new atomic ops, we use logic in
inet_ehash_nolisten() to detect the request was present in the same
ehash bucket where we try to insert the new child.
If request socket was not found, we have to undo the child creation.
This actually removes a spin_lock()/spin_unlock() pair in
reqsk_queue_unlink() for the fast path.
Fixes: e994b2f0fb92 ("tcp: do not lock listener to process SYN packets")
Fixes: 079096f103fa ("tcp/dccp: install syn_recv requests into ehash table")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
issues
Raw sockets with hdrincl enabled can insert ipv6 extension headers
right into the data stream. In case we need to fragment those packets,
we reparse the options header to find the place where we can insert
the fragment header. If the extension headers exceed the link's MTU we
actually cannot make progress in such a case.
Instead of ending up in broken arithmetic or rounding towards 0 and
entering an endless loop in ip6_fragment, just prevent those cases by
aborting early and signal -EMSGSIZE to user space.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The error condition -EAGAIN, which is signaled by throw routes, tells
the rules framework to walk on searching for next matches. If the walk
ends and we stop walking the rules with the result of a throw route we
have to translate the error conditions to -ENETUNREACH.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec
Steffen Klassert says:
====================
pull request (net): ipsec 2015-10-22
1) Fix IPsec pre-encap fragmentation for GSO packets.
From Herbert Xu.
2) Fix some header checks in _decode_session6.
We skip the header informations if the data pointer points
already behind the header in question for some protocols.
This is because we call pskb_may_pull with a negative value
converted to unsigened int from pskb_may_pull in this case.
Skipping the header informations can lead to incorrect policy
lookups. From Mathias Krause.
3) Allow to change the replay threshold and expiry timer of a
state without having to set other attributes like replay
counter and byte lifetime. Changing these other attributes
may break the SA. From Michael Rossberg.
4) Fix pmtu discovery for local generated packets.
We may fail dispatch to the inner address family.
As a reault, the local error handler is not called
and the mtu value is not reported back to userspace.
Please pull or let me know if there are problems.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
741a11d9e410 ("net: ipv6: Add RT6_LOOKUP_F_IFACE flag if oif is set")
adds the RT6_LOOKUP_F_IFACE flag to make device index mismatch fatal if
oif is given. Hajime reported that this change breaks the Mobile IPv6
use case that wants to force the message through one interface yet use
the source address from another interface. Handle this case by only
adding the flag if oif is set and saddr is not set.
Fixes: 741a11d9e410 ("net: ipv6: Add RT6_LOOKUP_F_IFACE flag if oif is set")
Cc: Hajime Tazaki <thehajime@gmail.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Tom Herbert added SIT support to GRO with commit
19424e052fb4 ("sit: Add gro callbacks to sit_offload"),
later reverted by Herbert Xu.
The problem came because Tom patch was building GRO
packets without proper meta data : If packets were locally
delivered, we would not care.
But if packets needed to be forwarded, GSO engine was not
able to segment individual segments.
With the following patch, we correctly set skb->encapsulation
and inner network header. We also update gso_type.
Tested:
Server :
netserver
modprobe dummy
ifconfig dummy0 8.0.0.1 netmask 255.255.255.0 up
arp -s 8.0.0.100 4e:32:51:04:47:e5
iptables -I INPUT -s 10.246.7.151 -j TEE --gateway 8.0.0.100
ifconfig sixtofour0
sixtofour0 Link encap:IPv6-in-IPv4
inet6 addr: 2002:af6:798::1/128 Scope:Global
inet6 addr: 2002:af6:798::/128 Scope:Global
UP RUNNING NOARP MTU:1480 Metric:1
RX packets:411169 errors:0 dropped:0 overruns:0 frame:0
TX packets:409414 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:20319631739 (20.3 GB) TX bytes:29529556 (29.5 MB)
Client :
netperf -H 2002:af6:798::1 -l 1000 &
Checked on server traffic copied on dummy0 and verify segments were
properly rebuilt, with proper IP headers, TCP checksums...
tcpdump on eth0 shows proper GRO aggregation takes place.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains four Netfilter fixes for net, they are:
1) Fix Kconfig dependencies of new nf_dup_ipv4 and nf_dup_ipv6.
2) Remove bogus test nh_scope in IPv4 rpfilter match that is breaking
--accept-local, from Xin Long.
3) Wait for RCU grace period after dropping the pending packets in the
nfqueue, from Florian Westphal.
4) Fix sleeping allocation while holding spin_lock_bh, from Nikolay Borisov.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
if_nlmsg_size() overestimates the minimum allocation size of netlink
dump request (when called from rtnl_calcit()) or the size of the
message (when called from rtnl_getlink()). This is because
ext_filter_mask is not supported by rtnl_link_get_af_size() and
rtnl_link_get_size().
The over-estimation is significant when at least one netdev has many
VLANs configured (8 bytes for each configured VLAN).
This patch-set "rightsizes" the protocol specific attribute size
calculation by propagating ext_filter_mask to rtnl_link_get_af_size()
and adding this a argument to get_link_af_size op in rtnl_af_ops.
Bridge module already used filtering aware sizing for notifications.
br_get_link_af_size_filtered() is consistent with the modified
get_link_af_size op so it replaces br_get_link_af_size() in br_af_ops.
br_get_link_af_size() becomes unused and thus removed.
Signed-off-by: Ronen Arad <ronen.arad@intel.com>
Acked-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
6e28b000825d ("net: Fix vti use case with oif in dst lookups for IPv6")
is missing the checks on FLOWI_FLAG_SKIP_NH_OIF. Add them.
Fixes: 42a7b32b73d6 ("xfrm: Add oif to dst lookups")
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Acked-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/usb/asix_common.c
net/ipv4/inet_connection_sock.c
net/switchdev/switchdev.c
In the inet_connection_sock.c case the request socket hashing scheme
is completely different in net-next.
The other two conflicts were overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 044a832a777 ("xfrm: Fix local error reporting crash
with interfamily tunnels") moved the setting of skb->protocol
behind the last access of the inner mode family to fix an
interfamily crash. Unfortunately now skb->protocol might not
be set at all, so we fail dispatch to the inner address family.
As a reault, the local error handler is not called and the
mtu value is not reported back to userspace.
We fix this by setting skb->protocol on message size errors
before we call xfrm_local_error.
Fixes: 044a832a7779c ("xfrm: Fix local error reporting crash with interfamily tunnels")
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains Netfilter/IPVS updates for your net-next
tree. Most relevantly, updates for the nfnetlink_log to integrate with
conntrack, fixes for cttimeout and improvements for nf_queue core, they are:
1) Remove useless ifdef around static inline function in IPVS, from
Eric W. Biederman.
2) Simplify the conntrack support for nfnetlink_queue: Merge
nfnetlink_queue_ct.c file into nfnetlink_queue_core.c, then rename it back
to nfnetlink_queue.c
3) Use y2038 safe timestamp from nfnetlink_queue.
4) Get rid of dead function definition in nf_conntrack, from Flavio
Leitner.
5) Attach conntrack support for nfnetlink_log.c, from Ken-ichirou MATSUZAWA.
This adds a new NETFILTER_NETLINK_GLUE_CT Kconfig switch that
controls enabling both nfqueue and nflog integration with conntrack.
The userspace application can request this via NFULNL_CFG_F_CONNTRACK
configuration flag.
6) Remove unused netns variables in IPVS, from Eric W. Biederman and
Simon Horman.
7) Don't put back the refcount on the cttimeout object from xt_CT on success.
8) Fix crash on cttimeout policy object removal. We have to flush out
the cttimeout extension area of the conntrack not to refer to an unexisting
object that was just removed.
9) Make sure rcu_callback completion before removing nfnetlink_cttimeout
module removal.
10) Fix compilation warning in br_netfilter when no nf_defrag_ipv4 and
nf_defrag_ipv6 are enabled. Patch from Arnd Bergmann.
11) Autoload ctnetlink dependencies when NFULNL_CFG_F_CONNTRACK is
requested. Again from Ken-ichirou MATSUZAWA.
12) Don't use pointer to previous hook when reinjecting traffic via
nf_queue with NF_REPEAT verdict since it may be already gone. This
also avoids a deadloop if the userspace application keeps returning
NF_REPEAT.
13) A bunch of cleanups for netfilter IPv4 and IPv6 code from Ian Morris.
14) Consolidate logger instance existence check in nfulnl_recv_config().
15) Fix broken atomicity when applying configuration updates to logger
instances in nfnetlink_log.
16) Get rid of the .owner attribute in our hook object. We don't need
this anymore since we're dropping pending packets that have escaped
from the kernel when unremoving the hook. Patch from Florian Westphal.
17) Remove unnecessary rcu_read_lock() from nf_reinject code, we always
assume RCU read side lock from .call_rcu in nfnetlink. Also from Florian.
18) Use static inline function instead of macros to define NF_HOOK() and
NF_HOOK_COND() when no netfilter support in on, from Arnd Bergmann.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
At the time of commit fff326990789 ("tcp: reflect SYN queue_mapping into
SYNACK packets") we had little ways to cope with SYN floods.
We no longer need to reflect incoming skb queue mappings, and instead
can pick a TX queue based on cpu cooking the SYNACK, with normal XPS
affinities.
Note that all SYNACK retransmits were picking TX queue 0, this no longer
is a win given that SYNACK rtx are now distributed on all cpus.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
