| Age | Commit message (Collapse) | Author |
|---|
|
The ip6 GRE tap device should not be forced to down state to change
the mac address and should allow live address change for tap device
similar to ipv4 gre.
Signed-off-by: Shweta Choudaha <schoudah@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
At present we perform an xfrm_lookup() for each UDPv6 message we
send. The lookup involves querying the flow cache (flow_cache_lookup)
and, in case of a cache miss, creating an XFRM bundle.
If we miss the flow cache, we can end up creating a new bundle and
deriving the path MTU (xfrm_init_pmtu) from on an already transformed
dst_entry, which we pass from the socket cache (sk->sk_dst_cache) down
to xfrm_lookup(). This can happen only if we're caching the dst_entry
in the socket, that is when we're using a connected UDP socket.
To put it another way, the path MTU shrinks each time we miss the flow
cache, which later on leads to incorrectly fragmented payload. It can
be observed with ESPv6 in transport mode:
1) Set up a transformation and lower the MTU to trigger fragmentation
# ip xfrm policy add dir out src ::1 dst ::1 \
tmpl src ::1 dst ::1 proto esp spi 1
# ip xfrm state add src ::1 dst ::1 \
proto esp spi 1 enc 'aes' 0x0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b0b
# ip link set dev lo mtu 1500
2) Monitor the packet flow and set up an UDP sink
# tcpdump -ni lo -ttt &
# socat udp6-listen:12345,fork /dev/null &
3) Send a datagram that needs fragmentation with a connected socket
# perl -e 'print "@" x 1470 | socat - udp6:[::1]:12345
2016/06/07 18:52:52 socat[724] E read(3, 0x555bb3d5ba00, 8192): Protocol error
00:00:00.000000 IP6 ::1 > ::1: frag (0|1448) ESP(spi=0x00000001,seq=0x2), length 1448
00:00:00.000014 IP6 ::1 > ::1: frag (1448|32)
00:00:00.000050 IP6 ::1 > ::1: ESP(spi=0x00000001,seq=0x3), length 1272
(^ ICMPv6 Parameter Problem)
00:00:00.000022 IP6 ::1 > ::1: ESP(spi=0x00000001,seq=0x5), length 136
4) Compare it to a non-connected socket
# perl -e 'print "@" x 1500' | socat - udp6-sendto:[::1]:12345
00:00:40.535488 IP6 ::1 > ::1: frag (0|1448) ESP(spi=0x00000001,seq=0x6), length 1448
00:00:00.000010 IP6 ::1 > ::1: frag (1448|64)
What happens in step (3) is:
1) when connecting the socket in __ip6_datagram_connect(), we
perform an XFRM lookup, miss the flow cache, create an XFRM
bundle, and cache the destination,
2) afterwards, when sending the datagram, we perform an XFRM lookup,
again, miss the flow cache (due to mismatch of flowi6_iif and
flowi6_oif, which is an issue of its own), and recreate an XFRM
bundle based on the cached (and already transformed) destination.
To prevent the recreation of an XFRM bundle, avoid an XFRM lookup
altogether whenever we already have a destination entry cached in the
socket. This prevents the path MTU shrinkage and brings us on par with
UDPv4.
The fix also benefits connected PINGv6 sockets, another user of
ip6_sk_dst_lookup_flow(), who also suffer messages being transformed
twice.
Joint work with Hannes Frederic Sowa.
Reported-by: Jan Tluka <jtluka@redhat.com>
Signed-off-by: Jakub Sitnicki <jkbs@redhat.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The v6 tcp stats scan do not provide TLP and ER timer information
correctly like the v4 version . This patch fixes that.
Fixes: 6ba8a3b19e76 ("tcp: Tail loss probe (TLP)")
Fixes: eed530b6c676 ("tcp: early retransmit")
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
queueing")
Paul Moore tracked a regression caused by a recent commit, which
mistakenly assumed that sk_filter() could be avoided if socket
had no current BPF filter.
The intent was to avoid udp_lib_checksum_complete() overhead.
But sk_filter() also checks skb_pfmemalloc() and
security_sock_rcv_skb(), so better call it.
Fixes: e6afc8ace6dd ("udp: remove headers from UDP packets before queueing")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Paul Moore <paul@paul-moore.com>
Tested-by: Paul Moore <paul@paul-moore.com>
Tested-by: Stephen Smalley <sds@tycho.nsa.gov>
Cc: samanthakumar <samanthakumar@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for your net tree,
they are:
1) Fix incorrect timestamp in nfnetlink_queue introduced when addressing
y2038 safe timestamp, from Florian Westphal.
2) Get rid of leftover conntrack definition from the previous merge
window, oneliner from Florian.
3) Make nf_queue handler pernet to resolve race on dereferencing the
hook state structure with netns removal, from Eric Biederman.
4) Ensure clean exit on unregistered helper ports, from Taehee Yoo.
5) Restore FLOWI_FLAG_KNOWN_NH in nf_dup_ipv6. This got lost while
generalizing xt_TEE to add packet duplication support in nf_tables,
from Paolo Abeni.
6) Insufficient netlink NFTA_SET_TABLE attribute check in
nf_tables_getset(), from Phil Turnbull.
7) Reject helper registration on duplicated ports via modparams.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Kconfig options I added to work around broken compilation ended
up screwing up things more, as I used the wrong symbol to control
compilation of the file, resulting in IPv6 fou support to never be built
into the kernel.
Changing CONFIG_NET_FOU_IPV6_TUNNELS to CONFIG_IPV6_FOU fixes that
problem, I had renamed the symbol in one location but not the other,
and as the file is never being used by other kernel code, this did not
lead to a build failure that I would have caught.
After that fix, another issue with the same patch becomes obvious, as we
'select INET6_TUNNEL', which is related to IPV6_TUNNEL, but not the same,
and this can still cause the original build failure when IPV6_TUNNEL is
not built-in but IPV6_FOU is. The fix is equally trivial, we just need
to select the right symbol.
I have successfully build 350 randconfig kernels with this patch
and verified that the driver is now being built.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reported-by: Valentin Rothberg <valentinrothberg@gmail.com>
Fixes: fabb13db448e ("fou: add Kconfig options for IPv6 support")
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With the commit 48e8aa6e3137 ("ipv6: Set FLOWI_FLAG_KNOWN_NH at
flowi6_flags") ip6_pol_route() callers were asked to to set the
FLOWI_FLAG_KNOWN_NH properly and xt_TEE was updated accordingly,
but with the later refactor in commit bbde9fc1824a ("netfilter:
factor out packet duplication for IPv4/IPv6") the flowi6_flags
update was lost.
This commit re-add it just before the routing decision.
Fixes: bbde9fc1824a ("netfilter: factor out packet duplication for IPv4/IPv6")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
A previous patch added the fou6.ko module, but that failed to link
in a couple of configurations:
net/built-in.o: In function `ip6_tnl_encap_add_fou_ops':
net/ipv6/fou6.c:88: undefined reference to `ip6_tnl_encap_add_ops'
net/ipv6/fou6.c:94: undefined reference to `ip6_tnl_encap_add_ops'
net/ipv6/fou6.c:97: undefined reference to `ip6_tnl_encap_del_ops'
net/built-in.o: In function `ip6_tnl_encap_del_fou_ops':
net/ipv6/fou6.c:106: undefined reference to `ip6_tnl_encap_del_ops'
net/ipv6/fou6.c:107: undefined reference to `ip6_tnl_encap_del_ops'
If CONFIG_IPV6=m, ip6_tnl_encap_add_ops/ip6_tnl_encap_del_ops
are in a module, but fou6.c can still be built-in, and that
obviously fails to link.
Also, if CONFIG_IPV6=y, but CONFIG_IPV6_TUNNEL=m or
CONFIG_IPV6_TUNNEL=n, the same problem happens for a different
reason.
This adds two new silent Kconfig symbols to work around both
problems:
- CONFIG_IPV6_FOU is now always set to 'm' if either CONFIG_NET_FOU=m
or CONFIG_IPV6=m
- CONFIG_IPV6_FOU_TUNNEL is set implicitly when IPV6_FOU is enabled
and NET_FOU_IP_TUNNELS is also turned out, and it will ensure
that CONFIG_IPV6_TUNNEL is also available.
The options could be made user-visible as well, to give additional
room for configuration, but it seems easier not to bother users
with more choice here.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: aa3463d65e7b ("fou: Add encap ops for IPv6 tunnels")
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In gre6 xmit path, we are sending a GRE packet, so set fl6 proto
to IPPROTO_GRE properly.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When creat an ip6gretap interface with an unreachable route,
the MTU is about 14 bytes larger than what was needed.
If the remote address is reachable:
ping6 2001:0:130::1 -c 2
PING 2001:0:130::1(2001:0:130::1) 56 data bytes
64 bytes from 2001:0:130::1: icmp_seq=1 ttl=64 time=1.46 ms
64 bytes from 2001:0:130::1: icmp_seq=2 ttl=64 time=81.1 ms
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case we find a socket with encapsulation enabled we should call
the encap_recv function even if just a udp header without payload is
available. The callbacks are responsible for correctly verifying and
dropping the packets.
Also, in case the header validation fails for geneve and vxlan we
shouldn't put the skb back into the socket queue, no one will pick
them up there. Instead we can simply discard them in the respective
encap_recv functions.
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch addresses the same issue we had for IPv4 where enabling GRE with
an inner checksum cannot be supported with FOU/GUE due to the fact that
they will jump past the GRE header at it is treated like a tunnel header.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since iptunnel_handle_offloads() is called in all paths we can
probably drop the block in ip6_tnl_xmit that was checking for
skb->encapsulation and resetting the inner headers.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Need to set dev features, use same values that are used in GREv6.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add netlink and setup for encapsulation
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add netlink and setup for encapsulation
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch add a new fou6 module that provides encapsulation
operations for IPv6.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add encap_hlen and ip_tunnel_encap structure to ip6_tnl. Add functions
for getting encap hlen, setting up encap on a tunnel, performing
encapsulation operation.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When performing foo-over-UDP, UDP packets are processed by the
encapsulation handler which returns another protocol to process.
This may result in processing two (or more) protocols in the
loop that are marked as INET6_PROTO_FINAL. The actions taken
for hitting a final protocol, in particular the skb_postpull_rcsum
can only be performed once.
This patch set adds a check of a final protocol has been seen. The
rules are:
- If the final protocol has not been seen any protocol is processed
(final and non-final). In the case of a final protocol, the final
actions are taken (like the skb_postpull_rcsum)
- If a final protocol has been seen (e.g. an encapsulating UDP
header) then no further non-final protocols are allowed
(e.g. extension headers). For more final protocols the
final actions are not taken (e.g. skb_postpull_rcsum).
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In ip6_input_finish the nexthdr protocol is retrieved from the
next header offset that is returned in the cb of the skb.
This method does not work for UDP encapsulation that may not
even have a concept of a nexthdr field (e.g. FOU).
This patch checks for a final protocol (INET6_PROTO_FINAL) when a
protocol handler returns > 0. If the protocol is not final then
resubmission is performed on nhoff value. If the protocol is final
then the nexthdr is taken to be the return value.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch defines two new GSO definitions SKB_GSO_IPXIP4 and
SKB_GSO_IPXIP6 along with corresponding NETIF_F_GSO_IPXIP4 and
NETIF_F_GSO_IPXIP6. These are used to described IP in IP
tunnel and what the outer protocol is. The inner protocol
can be deduced from other GSO types (e.g. SKB_GSO_TCPV4 and
SKB_GSO_TCPV6). The GSO types of SKB_GSO_IPIP and SKB_GSO_SIT
are removed (these are both instances of SKB_GSO_IPXIP4).
SKB_GSO_IPXIP6 will be used when support for GSO with IP
encapsulation over IPv6 is added.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In several gso_segment functions there are checks of gso_type against
a seemingly arbitrary list of SKB_GSO_* flags. This seems like an
attempt to identify unsupported GSO types, but since the stack is
the one that set these GSO types in the first place this seems
unnecessary to do. If a combination isn't valid in the first
place that stack should not allow setting it.
This is a code simplication especially for add new GSO types.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
tcp_hdr() is slightly more expensive than using skb->data in contexts
where we know they point to the same byte.
In receive path, tcp_v4_rcv() and tcp_v6_rcv() are in this situation,
as tcp header has not been pulled yet.
In output path, the same can be said when we just pushed the tcp header
in the skb, in tcp_transmit_skb() and tcp_make_synack()
Also factorize the two checks for tcb->tcp_flags & TCPHDR_SYN in
tcp_transmit_skb() and pass tcp header pointer to tcp_ecn_send(),
so that compiler can further optimize and avoid a reload.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
__sock_cmsg_send() might return different error codes, not only -EINVAL.
Fixes: 24025c465f77 ("ipv4: process socket-level control messages in IPv4")
Fixes: ad1e46a83716 ("ipv6: process socket-level control messages in IPv6")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The nf_conntrack_core.c fix in 'net' is not relevant in 'net-next'
because we no longer have a per-netns conntrack hash.
The ip_gre.c conflict as well as the iwlwifi ones were cases of
overlapping changes.
Conflicts:
drivers/net/wireless/intel/iwlwifi/mvm/tx.c
net/ipv4/ip_gre.c
net/netfilter/nf_conntrack_core.c
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, when creating or updating a route, no check is performed
in both ipv4 and ipv6 code to the hoplimit value.
The caller can i.e. set hoplimit to 256, and when such route will
be used, packets will be sent with hoplimit/ttl equal to 0.
This commit adds checks for the RTAX_HOPLIMIT value, in both ipv4
ipv6 route code, substituting any value greater than 255 with 255.
This is consistent with what is currently done for ADVMSS and MTU
in the ipv4 code.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While testing an OpenStack configuration using VXLANs I saw the following
call trace:
RIP: 0010:[<ffffffff815fad49>] udp4_lib_lookup_skb+0x49/0x80
RSP: 0018:ffff88103867bc50 EFLAGS: 00010286
RAX: ffff88103269bf00 RBX: ffff88103269bf00 RCX: 00000000ffffffff
RDX: 0000000000004300 RSI: 0000000000000000 RDI: ffff880f2932e780
RBP: ffff88103867bc60 R08: 0000000000000000 R09: 000000009001a8c0
R10: 0000000000004400 R11: ffffffff81333a58 R12: ffff880f2932e794
R13: 0000000000000014 R14: 0000000000000014 R15: ffffe8efbfd89ca0
FS: 0000000000000000(0000) GS:ffff88103fd80000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000488 CR3: 0000000001c06000 CR4: 00000000001426e0
Stack:
ffffffff81576515 ffffffff815733c0 ffff88103867bc98 ffffffff815fcc17
ffff88103269bf00 ffffe8efbfd89ca0 0000000000000014 0000000000000080
ffffe8efbfd89ca0 ffff88103867bcc8 ffffffff815fcf8b ffff880f2932e794
Call Trace:
[<ffffffff81576515>] ? skb_checksum+0x35/0x50
[<ffffffff815733c0>] ? skb_push+0x40/0x40
[<ffffffff815fcc17>] udp_gro_receive+0x57/0x130
[<ffffffff815fcf8b>] udp4_gro_receive+0x10b/0x2c0
[<ffffffff81605863>] inet_gro_receive+0x1d3/0x270
[<ffffffff81589e59>] dev_gro_receive+0x269/0x3b0
[<ffffffff8158a1b8>] napi_gro_receive+0x38/0x120
[<ffffffffa0871297>] gro_cell_poll+0x57/0x80 [vxlan]
[<ffffffff815899d0>] net_rx_action+0x160/0x380
[<ffffffff816965c7>] __do_softirq+0xd7/0x2c5
[<ffffffff8107d969>] run_ksoftirqd+0x29/0x50
[<ffffffff8109a50f>] smpboot_thread_fn+0x10f/0x160
[<ffffffff8109a400>] ? sort_range+0x30/0x30
[<ffffffff81096da8>] kthread+0xd8/0xf0
[<ffffffff81693c82>] ret_from_fork+0x22/0x40
[<ffffffff81096cd0>] ? kthread_park+0x60/0x60
The following trace is seen when receiving a DHCP request over a flow-based
VXLAN tunnel. I believe this is caused by the metadata dst having a NULL
dev value and as a result dev_net(dev) is causing a NULL pointer dereference.
To resolve this I am replacing the check for skb_dst(skb)->dev with just
skb->dev. This makes sense as the callers of this function are usually in
the receive path and as such skb->dev should always be populated. In
addition other functions in the area where these are called are already
using dev_net(skb->dev) to determine the namespace the UDP packet belongs
in.
Fixes: 63058308cd55 ("udp: Add udp6_lib_lookup_skb and udp4_lib_lookup_skb")
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When dealing with WCCP in gre6 tunnel, it sets the wrong tpi->protocol,
that is, ETH_P_IP instead of ETH_P_IPV6 for the encapuslated traffic.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Do not include attribute IFLA_GRE_TOS.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently the VRF driver uses the rx_handler to switch the skb device
to the VRF device. Switching the dev prior to the ip / ipv6 layer
means the VRF driver has to duplicate IP/IPv6 processing which adds
overhead and makes features such as retaining the ingress device index
more complicated than necessary.
This patch moves the hook to the L3 layer just after the first NF_HOOK
for PRE_ROUTING. This location makes exposing the original ingress device
trivial (next patch) and allows adding other NF_HOOKs to the VRF driver
in the future.
dev_queue_xmit_nit is exported so that the VRF driver can cycle the skb
with the switched device through the packet taps to maintain current
behavior (tcpdump can be used on either the vrf device or the enslaved
devices).
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Protocol for 4in6 tunnel is IPPROTO_IPIP. This was wrongly changed by
the last cleanup.
CC: Tom Herbert <tom@herbertland.com>
Fixes: 0d3c703a9d17 ("ipv6: Cleanup IPv6 tunnel receive path")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The handler 'ila_fill_encap_info' adds two attributes: ILA_ATTR_LOCATOR
and ILA_ATTR_CSUM_MODE.
nla_total_size_64bit() must be use for ILA_ATTR_LOCATOR.
Also, do nla_put_u8 instead of nla_put_u64 for ILA_ATTR_CSUM_MODE.
Fixes: f13a82d87b21 ("ipv6: use nla_put_u64_64bit()")
Fixes: 90bfe662db13 ("ila: add checksum neutral ILA translations")
Reported-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix two spots where o_flags in a tunnel are being compared to GRE_SEQ
instead of TUNNEL_SEQ.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We only need to reset network header here.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Need to use adjusted protocol value for setting inner protocol.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
GRE for IPv6 does not properly translate for GRE flags to tunnel
flags and vice versa. This patch fixes that.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In ip6gre_tnl_link_config set t->tun_len and t->hlen correctly for the
configuration. For hard_header_len and mtu calculation include
IPv6 header and encapsulation overhead.
In ip6gre_tunnel_init_common set t->tun_len and t->hlen correctly for
the configuration. Revert to setting hard_header_len instead of
needed_headroom.
Tested:
./ip link add name tun8 type ip6gretap remote \
2401:db00:20:911a:face:0:27:0 local \
2401:db00:20:911a:face:0:25:0 ttl 225
Gives MTU of 1434. That is equal to 1500 - 40 - 14 - 4 - 8.
./ip link add name tun8 type ip6gretap remote \
2401:db00:20:911a:face:0:27:0 local \
2401:db00:20:911a:face:0:25:0 ttl 225 okey 123
Gives MTU of 1430. That is equal to 1500 - 40 - 14 - 4 - 8 - 4.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move l3mdev_rt6_dst_by_oif and l3mdev_get_saddr to l3mdev.c. Collapse
l3mdev_get_rt6_dst into l3mdev_rt6_dst_by_oif since it is the only
user and keep the l3mdev_get_rt6_dst name for consistency with other
hooks.
A follow-on patch adds more code to these functions making them long
for inlined functions.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In netdevice.h we removed the structure in net-next that is being
changes in 'net'. In macsec.c and rtnetlink.c we have overlaps
between fixes in 'net' and the u64 attribute changes in 'net-next'.
The mlx5 conflicts have to do with vxlan support dependencies.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following large patchset contains Netfilter updates for your
net-next tree. My initial intention was to send you this in two goes but
when I looked back twice I already had this burden on top of me.
Several updates for IPVS from Marco Angaroni:
1) Allow SIP connections originating from real-servers to be load
balanced by the SIP persistence engine as is already implemented
in the other direction.
2) Release connections immediately for One-packet-scheduling (OPS)
in IPVS, instead of making it via timer and rcu callback.
3) Skip deleting conntracks for each one packet in OPS, and don't call
nf_conntrack_alter_reply() since no reply is expected.
4) Enable drop on exhaustion for OPS + SIP persistence.
Miscelaneous conntrack updates from Florian Westphal, including fix for
hash resize:
5) Move conntrack generation counter out of conntrack pernet structure
since this is only used by the init_ns to allow hash resizing.
6) Use get_random_once() from packet path to collect hash random seed
instead of our compound.
7) Don't disable BH from ____nf_conntrack_find() for statistics,
use NF_CT_STAT_INC_ATOMIC() instead.
8) Fix lookup race during conntrack hash resizing.
9) Introduce clash resolution on conntrack insertion for connectionless
protocol.
Then, Florian's netns rework to get rid of per-netns conntrack table,
thus we use one single table for them all. There was consensus on this
change during the NFWS 2015 and, on top of that, it has recently been
pointed as a source of multiple problems from unpriviledged netns:
11) Use a single conntrack hashtable for all namespaces. Include netns
in object comparisons and make it part of the hash calculation.
Adapt early_drop() to consider netns.
12) Use single expectation and NAT hashtable for all namespaces.
13) Use a single slab cache for all namespaces for conntrack objects.
14) Skip full table scanning from nf_ct_iterate_cleanup() if the pernet
conntrack counter tells us the table is empty (ie. equals zero).
Fixes for nf_tables interval set element handling, support to set
conntrack connlabels and allow set names up to 32 bytes.
15) Parse element flags from element deletion path and pass it up to the
backend set implementation.
16) Allow adjacent intervals in the rbtree set type for dynamic interval
updates.
17) Add support to set connlabel from nf_tables, from Florian Westphal.
18) Allow set names up to 32 bytes in nf_tables.
Several x_tables fixes and updates:
19) Fix incorrect use of IS_ERR_VALUE() in x_tables, original patch
from Andrzej Hajda.
And finally, miscelaneous netfilter updates such as:
20) Disable automatic helper assignment by default. Note this proc knob
was introduced by a9006892643a ("netfilter: nf_ct_helper: allow to
disable automatic helper assignment") 4 years ago to start moving
towards explicit conntrack helper configuration via iptables CT
target.
21) Get rid of obsolete and inconsistent debugging instrumentation
in x_tables.
22) Remove unnecessary check for null after ip6_route_output().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Tables have to exist for VRFs to function. Ensure they exist
when VRF device is created.
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Responses for packets to unused ports are getting lost with L3 domains.
IPv4 has ip_send_unicast_reply for sending TCP responses which accounts
for L3 domains; update the IPv6 counterpart tcp_v6_send_response.
For icmp the L3 master check needs to be moved up in icmp6_send
to properly respond to UDP packets to a port with no listener.
Fixes: ca254490c8df ("net: Add VRF support to IPv6 stack")
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The dprintf() and duprintf() functions are enabled at compile time,
these days we have better runtime debugging through pr_debug() and
static keys.
On top of this, this debugging is so old that I don't expect anyone
using this anymore, so let's get rid of this.
IP_NF_ASSERT() is still left in place, although this needs that
NETFILTER_DEBUG is enabled, I think these assertions provide useful
context information when reading the code.
Note that ARP_NF_ASSERT() has been removed as there is no user of
this.
Kill also DEBUG_ALLOW_ALL and a couple of pr_error() and pr_debug()
spots that are inconsistently placed in the code.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
The ipv6 gre implementation was cleaned up to share more code
with the ipv4 version, but it can be enabled even when NET_IPGRE_DEMUX
is disabled, resulting in a link error:
net/built-in.o: In function `gre_rcv':
:(.text+0x17f5d0): undefined reference to `gre_parse_header'
ERROR: "gre_parse_header" [net/ipv6/ip6_gre.ko] undefined!
This adds a Kconfig dependency to prevent that now invalid
configuration.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 308edfdf1563 ("gre6: Cleanup GREv6 receive path, call common GRE functions")
Acked-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It's easier for gre_parse_header to return the header length instead of
filing it into a parameter. That way, the callers that don't care about the
header length can just check whether the returned value is lower than zero.
In gre_err, the tunnel header must not be pulled. See commit b7f8fe251e46
("gre: do not pull header in ICMP error processing") for details.
This patch reduces the conflict between the mentioned commit and commit
95f5c64c3c13 ("gre: Move utility functions to common headers").
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Acked-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
net/ipv4/ip_gre.c
Minor conflicts between tunnel bug fixes in net and
ipv6 tunnel cleanups in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The handler 'ila_fill_encap_info' adds one attribute: ILA_ATTR_LOCATOR.
Fixes: 65d7ab8de582 ("net: Identifier Locator Addressing module")
CC: Tom Herbert <tom@herbertland.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the sendmsg function of UDP, raw, ICMP and l2tp sockets, we use local
variables like hlimits, tclass, opt and dontfrag and pass them to corresponding
functions like ip6_make_skb, ip6_append_data and xxx_push_pending_frames.
This is not a good practice and makes it hard to add new parameters.
This fix introduces a new struct ipcm6_cookie similar to ipcm_cookie in
ipv4 and include the above mentioned variables. And we only pass the
pointer to this structure to corresponding functions. This makes it easier
to add new parameters in the future and makes the function cleaner.
Signed-off-by: Wei Wang <weiwan@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
