| Age | Commit message (Collapse) | Author |
|---|
|
Add SPDX license identifiers to all files which:
- Have no license information of any form
- Have MODULE_LICENCE("GPL*") inside which was used in the initial
scan/conversion to ignore the file
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The udp-tunnel setup allows binding sockets to a network device. Prefer
the new SO_BINDTOIFINDEX to avoid temporarily resolving the device-name
just to look it up in the ioctl again.
Reviewed-by: Tom Gundersen <teg@jklm.no>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
UDP tunnel sockets are always opened unbound to a specific device. This
patch allow the socket to be bound on a custom device, which
incidentally makes UDP tunnels VRF-aware if binding to an l3mdev.
Signed-off-by: Alexis Bauvin <abauvin@scaleway.com>
Reviewed-by: Amine Kherbouche <akherbouche@scaleway.com>
Tested-by: Amine Kherbouche <akherbouche@scaleway.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For both IPv4 and IPv6, if we can't match errors to a socket, try
tunnels before ignoring them. Look up a socket with the original source
and destination ports as found in the UDP packet inside the ICMP payload,
this will work for tunnels that force the same destination port for both
endpoints, i.e. VXLAN and GENEVE.
Actually, lwtunnels could break this assumption if they are configured by
an external control plane to have different destination ports on the
endpoints: in this case, we won't be able to trace ICMP messages back to
them.
For IPv6 redirect messages, call ip6_redirect() directly with the output
interface argument set to the interface we received the packet from (as
it's the very interface we should build the exception on), otherwise the
new nexthop will be rejected. There's no such need for IPv4.
Tunnels can now export an encap_err_lookup() operation that indicates a
match. Pass the packet to the lookup function, and if the tunnel driver
reports a matching association, continue with regular ICMP error handling.
v2:
- Added newline between network and transport header sets in
__udp{4,6}_lib_err_encap() (David Miller)
- Removed redundant skb_reset_network_header(skb); in
__udp4_lib_err_encap()
- Removed redundant reassignment of iph in __udp4_lib_err_encap()
(Sabrina Dubroca)
- Edited comment to __udp{4,6}_lib_err_encap() to reflect the fact this
won't work with lwtunnels configured to use asymmetric ports. By the way,
it's VXLAN, not VxLAN (Jiri Benc)
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds a new NETDEV_UDP_TUNNEL_DROP_INFO event, similar to
NETDEV_UDP_TUNNEL_PUSH_INFO, to signal to un-offload ports.
This also adds udp_tunnel_drop_rx_port(), which calls
ndo_udp_tunnel_del.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If NETIF_F_RX_UDP_TUNNEL_PORT was disabled on a given netdevice, skip
the tunnel offload ndo call during tunnel port creation and deletion.
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that we have all the drivers using udp_tunnel_get_rx_ports,
ndo_add_udp_enc_rx_port, and ndo_del_udp_enc_rx_port we can drop the
function calls that were specific to VXLAN and GENEVE.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch merges the notifiers for VXLAN and GENEVE into a single UDP
tunnel notifier. The idea is that we will want to only have to make one
notifier call to receive the list of ports for VXLAN and GENEVE tunnels
that need to be offloaded.
In addition we add a new set of ndo functions named ndo_udp_tunnel_add and
ndo_udp_tunnel_del that are meant to allow us to track the tunnel meta-data
such as port and address family as tunnels are added and removed. The
tunnel meta-data is now transported in a structure named udp_tunnel_info
which for now carries the type, address family, and port number. In the
future this could be updated so that we can include a tuple of values
including things such as the destination IP address and other fields.
I also ended up going with a naming scheme that consisted of using the
prefix udp_tunnel on function names. I applied this to the notifier and
ndo ops as well so that it hopefully points to the fact that these are
primarily used in the udp_tunnel functions.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch merges the GENEVE and VXLAN code so that both functions pass
through a shared code path. This way we can start the effort of using a
single function on the network device drivers to handle both of these
tunnel types.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add gro_receive and gro_complete to struct udp_tunnel_sock_cfg.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IPCB may contain data from previous layers (in the observed case the
qdisc layer). In the observed scenario, the data was misinterpreted as
ip header options, which later caused the ihl to be set to an invalid
value (<5). This resulted in an infinite loop in the mips implementation
of ip_fast_csum.
This patch clears IPCB(skb)->opt before dst_link_failure can be called for
various types of tunnels. This change only applies to encapsulated ipv4
packets.
The code introduced in 11c21a30 which clears all of IPCB has been removed
to be consistent with these changes, and instead the opt field is cleared
unconditionally in ip_tunnel_xmit. The change in ip_tunnel_xmit applies to
SIT, GRE, and IPIP tunnels.
The relevant vti, l2tp, and pptp functions already contain similar code for
clearing the IPCB.
Signed-off-by: Bernie Harris <bernie.harris@alliedtelesis.co.nz>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
By moving stats update into iptunnel_xmit(), we can simplify
iptunnel_xmit() usage. With this change there is no need to
call another function (iptunnel_xmit_stats()) to update stats
in tunnel xmit code path.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce function udp_tun_rx_dst() to initialize tunnel dst on
receive path.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Reviewed-by: Jesse Gross <jesse@nicira.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that sk_alloc knows when a kernel socket is being allocated modify
it to not reference count the network namespace of kernel sockets.
Keep track of if a socket needs reference counting by adding a flag to
struct sock called sk_net_refcnt.
Update all of the callers of sock_create_kern to stop using
sk_change_net and sk_release_kernel as those hacks are no longer
needed, to avoid reference counting a kernel socket.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is long overdue, and is part of cleaning up how we allocate kernel
sockets that don't reference count struct net.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
That was we can make sure the output path of ipv4/ipv6 operate on
the UDP socket rather than whatever random thing happens to be in
skb->sk.
Based upon a patch by Jiri Pirko.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
|
|
The UDP tunnel transmit functions udp_tunnel_xmit_skb and
udp_tunnel6_xmit_skb include a socket argument. The socket being
passed to the functions (from VXLAN) is a UDP created for receive
side. The only thing that the socket is used for in the transmit
functions is to get the setting for checksum (enabled or zero).
This patch removes the argument and and adds a nocheck argument
for checksum setting. This eliminates the unnecessary dependency
on a UDP socket for UDP tunnel transmit.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move convert_csum from udp_sock to inet_sock. This allows the
possibility that we can use convert checksum for different types
of sockets and also allows convert checksum to be enabled from
inet layer (what we'll want to do when enabling IP_CHECKSUM cmsg).
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Added a few more UDP tunnel APIs that can be shared by UDP based
tunnel protocol implementation. The main ones are highlighted below.
setup_udp_tunnel_sock() configures UDP listener socket for
receiving UDP encapsulated packets.
udp_tunnel_xmit_skb() and upd_tunnel6_xmit_skb() transmit skb
using UDP encapsulation.
udp_tunnel_sock_release() closes the UDP tunnel listener socket.
Signed-off-by: Andy Zhou <azhou@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add ip6_udp_tunnel.c for ipv6 UDP tunnel functions to avoid ifdefs
in udp_tunnel.c
Signed-off-by: Andy Zhou <azhou@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Added udp_tunnel.c which can contain some common functions for UDP
tunnels. The first function in this is udp_sock_create which is used
to open the listener port for a UDP tunnel.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
