| Age | Commit message (Collapse) | Author |
|---|
|
The bridge VLANs are not offloaded by dsa_port_vlan_* if the port is
not bridged or if its bridge is not VLAN aware.
This is a good thing but other corners of DSA, such as the tag_8021q
driver, may need to program VLANs regardless the bridge state.
And also because bridge_dev is specific to user ports anyway, move
these checks were it belongs, one layer up in the slave code.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently dsa_port_vid_add returns 0 if the switch returns -EOPNOTSUPP.
This function is used in the tag_8021q.c code to offload the PVID of
ports, which would simply not work if .port_vlan_add is not supported
by the underlying switch.
Do not skip -EOPNOTSUPP in dsa_port_vid_add but only when necessary,
that is to say in dsa_slave_vlan_rx_add_vid.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Supported PHY features are either auto-detected or explicitly set.
In both cases calling genphy_config_init isn't needed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support for enabling or disabling the flooding of
unknown multicast traffic on the CPU ports, depending on the value
of the switchdev SWITCHDEV_ATTR_ID_BRIDGE_MROUTER attribute.
The current behavior is kept unchanged but a user can now prevent
the CPU conduit to be flooded with a lot of unregistered traffic that
the network stack needs to filter in software with e.g.:
echo 0 > /sys/class/net/br0/multicast_router
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current DSA code handling switchdev objects does not recurse into
the lower devices thus is never called with an orig_dev member being
a bridge device, hence remove this useless check.
At the same time, remove the comments about the callers, which is
unlikely to be updated if the code changes and thus will be confusing.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We need to specifically deal with phylink_of_phy_connect() returning
-ENODEV, because this can happen when a CPU/DSA port does connect
neither to a PHY, nor has a fixed-link property. This is a valid use
case that is permitted by the binding and indicates to the switch:
auto-configure port with maximum capabilities.
Fixes: 0e27921816ad ("net: dsa: Use PHYLINK for the CPU/DSA ports")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some ISDN files that got removed in net-next had some changes
done in mainline, take the removals.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
For DSA switches that do not have an .adjust_link callback, aka those
who transitioned totally to the PHYLINK-compliant API, use PHYLINK to
drive the CPU/DSA ports.
The PHYLIB usage and .adjust_link are kept but deprecated, and users are
asked to transition from it. The reason why we can't do anything for
them is because PHYLINK does not wrap the fixed-link state behind a
phydev object, so we cannot wrap .phylink_mac_config into .adjust_link
unless we fabricate a phy_device structure.
For these ports, the newly introduced PHYLINK_DEV operation type is
used and the dsa_switch device structure is passed to PHYLINK for
printing purposes. The handling of the PHYLINK_NETDEV and PHYLINK_DEV
PHYLINK instances is common from the perspective of the driver.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to have a common handling of PHYLINK for the slave and non-user
ports, the DSA core glue logic (between PHYLINK and the driver) must use
an API that does not rely on a struct net_device.
These will also be called by the CPU-port-handling code in a further
patch.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is needed so that the newly introduced tag_8021q may access these
core DSA functions when built as a module.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This hides the need to perform a two-phase transaction and construct a
switchdev_obj_port_vlan struct.
Call graph (including a function that will be introduced in a follow-up
patch) looks like this now (same for the *_vlan_del function):
dsa_slave_vlan_rx_add_vid dsa_port_setup_8021q_tagging
| |
| |
| +-------------+
| |
v v
dsa_port_vid_add dsa_slave_port_obj_add
| |
+-------+ +-------+
| |
v v
dsa_port_vlan_add
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Even if VLAN filtering is global, DSA will call this callback once per
each port. Drivers should not have to compare the global state with the
requested change. So let DSA do it.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current behavior is not as obvious as one would assume (which is
that, if the driver set vlan_filtering_is_global = 1, then checking any
dp->vlan_filtering would yield the same result). Only the ports which
are actively enslaved into a bridge would have vlan_filtering set.
This makes it tricky for drivers to check what the global state is.
So fix this and make the struct dsa_switch hold this global setting.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On some switches, the action of whether to parse VLAN frame headers and use
that information for ingress admission is configurable, but not per
port. Such is the case for the Broadcom BCM53xx and the NXP SJA1105
families, for example. In that case, DSA can prevent the bridge core
from trying to apply different VLAN filtering settings on net devices
that belong to the same switch.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This allows drivers to query the VLAN setting imposed by the bridge
driver directly from DSA, instead of keeping their own state based on
the .port_vlan_filtering callback.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
The call to of_parse_phandle returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./net/dsa/port.c:294:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 284, but without a corresponding object release within this function.
./net/dsa/dsa2.c:627:3-9: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 618, but without a corresponding object release within this function.
./net/dsa/dsa2.c:630:3-9: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 618, but without a corresponding object release within this function.
./net/dsa/dsa2.c:636:3-9: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 618, but without a corresponding object release within this function.
./net/dsa/dsa2.c:639:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 618, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
No current DSA driver makes use of the phydev parameter passed to the
disable_port call. Remove it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Three conflicts, one of which, for marvell10g.c is non-trivial and
requires some follow-up from Heiner or someone else.
The issue is that Heiner converted the marvell10g driver over to
use the generic c45 code as much as possible.
However, in 'net' a bug fix appeared which makes sure that a new
local mask (MDIO_AN_10GBT_CTRL_ADV_NBT_MASK) with value 0x01e0
is cleared.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to properly support VLAN filtering being enabled/disabled on a
bridge, while having other ports being non bridge port members, we need
to support the ndo_vlan_rx_{add,kill}_vid callbacks in order to make
sure the non-bridge ports can continue receiving VLAN tags, even when
the switch is globally configured to do ingress/egress VID checking.
Since we can call dsa_port_vlan_{add,del} with a bridge_dev pointer
NULL, we now need to check that in these two functions.
We specifically deal with two possibly problematic cases:
- creating a bridge VLAN entry while there is an existing VLAN device
claiming that same VID
- creating a VLAN device while there is an existing bridge VLAN entry
with that VID
Those are both resolved with returning -EBUSY back to user-space.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation for removing SWITCHDEV_ATTR_ID_PORT_BRIDGE_FLAGS_SUPPORT,
add support for a function that processes the
SWITCHDEV_ATTR_ID_PORT_BRIDGE_FLAGS and
SWITCHDEV_ATTR_ID_PORT_PRE_BRIDGE_FLAGS attributes and returns not
supported for any flag set, since DSA does not currently support
toggling those bridge port attributes (yet).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Switches work by learning the MAC address for each attached station by
monitoring traffic from each station. When a station sends a packet,
the switch records which port the MAC address is connected to.
With IPv4 networking, before communication commences with a neighbour,
an ARP packet is broadcasted to all stations asking for the MAC address
corresponding with the IPv4. The desired station responds with an ARP
reply, and the ARP reply causes the switch to learn which port the
station is connected to.
With IPv6 networking, the situation is rather different. Rather than
broadcasting ARP packets, a "neighbour solicitation" is multicasted
rather than broadcasted. This multicast needs to reach the intended
station in order for the neighbour to be discovered.
Once a neighbour has been discovered, and entered into the sending
stations neighbour cache, communication can restart at a point later
without sending a new neighbour solicitation, even if the entry in
the neighbour cache is marked as stale. This can be after the MAC
address has expired from the forwarding cache of the DSA switch -
when that occurs, there is a long pause in communication.
Our DSA implementation for mv88e6xxx switches disables flooding of
multicast and unicast frames for bridged ports. As per the above
description, this is fine for IPv4 networking, since the broadcasted
ARP queries will be sent to and received by all stations on the same
network. However, this breaks IPv6 very badly - blocking neighbour
solicitations and later causing connections to stall.
The defaults that the Linux bridge code expect from bridges are for
unknown unicast and unknown multicast frames to be flooded to all ports
on the bridge, which is at odds to the defaults adopted by our DSA
implementation for mv88e6xxx switches.
This commit enables by default flooding of both unknown unicast and
unknown multicast frames whenever a port is added to a bridge, and
disables the flooding when a port leaves the bridge. This means that
mv88e6xxx DSA switches now behave as per the bridge(8) man page, and
IPv6 works flawlessly through such a switch.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Linux bridge implementation allows various properties of the bridge
to be controlled, such as flooding unknown unicast and multicast frames.
This patch adds the necessary DSA infrastructure to allow the Linux
bridge support to control these properties for DSA switches.
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
[florian: Add missing dp and ds variables declaration to fix build]
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a DSA port is added to a bridge and brought up, the resulting STP
state programmed into the hardware depends on the order that these
operations are performed. However, the Linux bridge code believes that
the port is in disabled mode.
If the DSA port is first added to a bridge and then brought up, it will
be in blocking mode. If it is brought up and then added to the bridge,
it will be in disabled mode.
This difference is caused by DSA always setting the STP mode in
dsa_port_enable() whether or not this port is part of a bridge. Since
bridge always sets the STP state when the port is added, brought up or
taken down, it is unnecessary for us to manipulate the STP state.
Apparently, this code was copied from Rocker, and the very next day a
similar fix for Rocker was merged but was not propagated to DSA. See
e47172ab7e41 ("rocker: put port in FORWADING state after leaving bridge")
Fixes: b73adef67765 ("net: dsa: integrate with SWITCHDEV for HW bridging")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Due to an explicit check in rocker_world_port_obj_vlan_add(),
dsa_slave_switchdev_event() resp. port_switchdev_event(), VLAN objects
that are added to a device that is not a front-panel port device are
ignored. Therefore this check is immaterial.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A follow-up patch enables emitting VLAN notifications for the bridge CPU
port in addition to the existing slave port notifications. These
notifications have orig_dev set to the bridge in question.
Because there's no specific support for these VLANs, just ignore the
notifications to maintain the current behavior.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement the same type of ethtool diversion that we have for
ETH_SS_STATS and make it work with ETH_SS_PHY_STATS. This allows
providing PHY level statistics for CPU ports that are directly
connecting to a PHY device.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation for having more call sites attempting to obtain a
reference against a PHY device corresponding to a particular port,
introduce a helper function for that purpose.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds support for enabling the internal PHY for a 'cpu' port.
It has been tested on GE B850v3, B650v3 and B450v3, which have a
built-in MV88E6240 switch hardwired to a PCIe based network card.
On these machines the internal PHY of the i210 network card and
the Marvell switch are connected to each other and must be enabled
for properly using the switch. While the i210 PHY will be enabled
when the network interface is enabled, the switch's port is not
exposed as network interface. Additionally the mv88e6xxx driver
resets the chip during probe, so the PHY is disabled without this
patch.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The software bridge can be build with vlan filtering support
included. However, by default it is turned off. In its turned off
state, it still passes VLANs via switchev, even though they are not to
be used. Don't pass these VLANs to the hardware. Only do so when vlan
filtering is enabled.
This fixes at least one corner case. There are still issues in other
corners, such as when vlan_filtering is later enabled.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The notify mechanism does not need to modify the port it is notifying.
So make the parameter const.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The new bindings (dsa2.c) and the old bindings (legacy.c) share two
helpers dsa_cpu_dsa_setup and dsa_cpu_dsa_destroy, used to register or
deregister a fixed PHY if a given port has a corresponding device node.
Unclutter the code by moving them into two new port.c helpers,
dsa_port_fixed_link_register_of and dsa_port_fixed_link_(un)register_of.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Provide dsa_port_enable and dsa_port_disable helpers to respectively
enable and disable a switch port. This makes the dsa_port_set_state_now
helper static.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Dumping a DSA port's FDB entries is not specific to a DSA slave, so add
a dsa_port_fdb_dump function, similarly to dsa_port_fdb_add and
dsa_port_fdb_del.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
>From all switchdev devices only DSA requires special FDB dump. This is due
to lack of ability for syncing the hardware learned FDBs with the bridge.
Due to this it is removed from switchdev and moved inside DSA.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently the MDB HW database is synced with the bridge's one, thus,
There is no need to support special dump functionality.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The bridge port attributes/vlan for DSA devices should be set only
from bridge code. Furthermore, The vlans are synced totally with the
bridge so there is no need for special dump support.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, the switchdev objects are embedded inside the DSA notifier
info. This patch removes this dependency. This is done as a preparation
stage before adding support for learning FDB through the switchdev
notification chain.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The prepare phase for FDB add is unneeded because most of DSA devices
can have failures during bus transactions (SPI, I2C, etc.), thus, the
prepare phase cannot guarantee success of the commit stage.
The support for learning FDB through notification chain, which will be
introduced in the following patches, will provide the ability to notify
back the bridge about successful offload.
Signed-off-by: Arkadi Sharshevsky <arkadis@mellanox.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that the switchdev bridge ageing time attribute is propagated to all
switch chips of the fabric, each switch can check if the requested value
is valid and program itself, so that the whole fabric shares a common
ageing time setting.
This is especially needed for switch chips in between others, containing
no bridge port members but evidently used in the data path.
To achieve that, remove the condition which skips the other switches. We
also don't need to identify the target switch anymore, thus remove the
sw_index member of the dsa_notifier_ageing_time_info notifier structure.
On ZII Dev Rev B (with two 88E6352 and one 88E6185) and ZII Dev Rev C
(with two 88E6390X), we have the following hardware configuration:
# ip link add name br0 type bridge
# ip link set master br0 dev lan6
br0: port 1(lan6) entered blocking state
br0: port 1(lan6) entered disabled state
# echo 2000 > /sys/class/net/br0/bridge/ageing_time
Before this patch:
zii-rev-b# cat /sys/kernel/debug/mv88e6xxx/sw*/age_time
300000
300000
15000
zii-rev-c# cat /sys/kernel/debug/mv88e6xxx/sw*/age_time
300000
18750
After this patch:
zii-rev-b# cat /sys/kernel/debug/mv88e6xxx/sw*/age_time
15000
15000
15000
zii-rev-c# cat /sys/kernel/debug/mv88e6xxx/sw*/age_time
18750
18750
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add two new DSA_NOTIFIER_VLAN_ADD and DSA_NOTIFIER_VLAN_DEL events to
notify not only a single switch, but all switches of a the fabric when
an VLAN entry is added or removed.
For the moment, keep the current behavior and ignore other switches.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add two new DSA_NOTIFIER_MDB_ADD and DSA_NOTIFIER_MDB_DEL events to
notify not only a single switch, but all switches of a the fabric when
an MDB entry is added or removed.
For the moment, keep the current behavior and ignore other switches.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add two new DSA_NOTIFIER_FDB_ADD and DSA_NOTIFIER_FDB_DEL events to
notify not only a single switch, but all switches of a the fabric when
an FDB entry is added or removed.
For the moment, keep the current behavior and ignore other switches.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch keeps the port-wide ageing time handling code in
dsa_port_ageing_time, pushes the requested ageing time value in a new
switch fabric notification, and moves the switch-wide ageing time
handling code in dsa_switch_ageing_time.
This has the effect that now not only the switch that the target port
belongs to can be programmed, but all switches composing the switch
fabric. For the moment, keep the current behavior and ignore other
switches.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move the DSA port code which handles VLAN objects in port.c, where it
belongs.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move the DSA port code which handles MDB objects in port.c, where it
belongs.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move the DSA port code which handles FDB objects in port.c, where it
belongs.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move the DSA port code which sets a port ageing time in port.c, where it
belongs.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move the DSA port code which sets VLAN filtering on a port in port.c,
where it belongs.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
