| Age | Commit message (Collapse) | Author |
|---|
|
There are use cases for which the existing tagger, based on the NPI
(Node Processor Interface) functionality, is insufficient.
Namely:
- Frames injected through the NPI port bypass the frame analyzer, so no
source address learning is performed, no TSN stream classification,
etc.
- Flow control is not functional over an NPI port (PAUSE frames are
encapsulated in the same Extraction Frame Header as all other frames)
- There can be at most one NPI port configured for an Ocelot switch. But
in NXP LS1028A and T1040 there are two Ethernet CPU ports. The non-NPI
port is currently either disabled, or operated as a plain user port
(albeit an internally-facing one). Having the ability to configure the
two CPU ports symmetrically could pave the way for e.g. creating a LAG
between them, to increase bandwidth seamlessly for the system.
So there is a desire to have an alternative to the NPI mode. This change
keeps the default tagger for the Seville and Felix switches as "ocelot",
but it can be changed via the following device attribute:
echo ocelot-8021q > /sys/class/<dsa-master>/dsa/tagging
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for Arrow SpeedChips XRS700x single byte tag trailer. This
is modeled on tag_trailer.c which works in a similar way.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Ethertype DSA encodes exactly the same information in the DSA tag as
the non-ethertype variety. So refactor out the common parts and reuse
them for both protocols.
This is ensures tag parsing and generation is always consistent across
all mv88e6xxx chips.
While we are at it, explicitly deal with all possible CPU codes on
receive, making sure to set offload_fwd_mark as appropriate.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The Hirschmann Hellcreek TSN switches have a special tagging protocol for frames
exchanged between the CPU port and the master interface. The format is a one
byte trailer indicating the destination or origin port.
It's quite similar to the Micrel KSZ tagging. That's why the implementation is
based on that code.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This implements the known parts of the Realtek 4 byte
tag protocol version 0xA, as found in the RTL8366RB
DSA switch.
It is designated as protocol version 0xA as a
different Realtek 4 byte tag format with protocol
version 0x9 is known to exist in the Realtek RTL8306
chips.
The tag and switch chip lacks public documentation, so
the tag format has been reverse-engineered from
packet dumps. As only ingress traffic has been available
for analysis an egress tag has not been possible to
develop (even using educated guesses about bit fields)
so this is as far as it gets. It is not known if the
switch even supports egress tagging.
Excessive attempts to figure out the egress tag format
was made. When nothing else worked, I just tried all bit
combinations with 0xannp where a is protocol and p is
port. I looped through all values several times trying
to get a response from ping, without any positive
result.
Using just these ingress tags however, the switch
functionality is vastly improved and the packets find
their way into the destination port without any
tricky VLAN configuration. On the D-Link DIR-685 the
LAN ports now come up and respond to ping without
any command line configuration so this is a real
improvement for users.
Egress packets need to be restricted to the proper
target ports using VLAN, which the RTL8366RB DSA
switch driver already sets up.
Cc: DENG Qingfang <dqfext@gmail.com>
Cc: Mauri Sandberg <sandberg@mailfence.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for tag format used in Atheros AR9331 built-in switch.
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While it is entirely possible that this tagger format is in fact more
generic than just these 2 switch families, I don't have that knowledge.
The Seville switch in NXP T1040 has a similar frame format, but there
are enough differences (e.g. DEST field starts at bit 57 instead of 56)
that calling this file tag_vitesse.c is a bit of a stretch at the
moment. The frame format has been listed in a comment so that people who
add support for further Vitesse switches can rework this tagger while
keeping compatibility with Felix.
The "ocelot" name was chosen instead of "felix" because even the Ocelot
switch can act as a DSA device when it is used in NPI mode, and the Felix
tagger format is almost identical. Currently it is only used for the
Felix switch embedded in the NXP LS1028A chip.
The ABI for this tagger should be considered "not stable" at the moment.
The DSA tag is always placed before the Ethernet header and therefore,
we are using the long prefix for RX tags to avoid putting the DSA master
port in promiscuous mode. Once there will be an API in DSA for drivers
to request DSA masters to be in promiscuous mode unconditionally, we
will switch to the "no prefix" extraction frame header, which will save
16 padding bytes for each RX frame.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove the superfluous NET_DSA_TAG_KSZ_COMMON and just use the existing
NET_DSA_TAG_KSZ. Update the description to mention the three switch
families it supports. No functional change.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to support this, we are creating a make-shift switch tag out of
a VLAN trunk configured on the CPU port. Termination of normal traffic
on switch ports only works when not under a vlan_filtering bridge.
Termination of management (PTP, BPDU) traffic works under all
circumstances because it uses a different tagging mechanism
(incl_srcpt). We are making use of the generic CONFIG_NET_DSA_TAG_8021Q
code and leveraging it from our own CONFIG_NET_DSA_TAG_SJA1105.
There are two types of traffic: regular and link-local.
The link-local traffic received on the CPU port is trapped from the
switch's regular forwarding decisions because it matched one of the two
DMAC filters for management traffic.
On transmission, the switch requires special massaging for these
link-local frames. Due to a weird implementation of the switching IP, by
default it drops link-local frames that originate on the CPU port.
It needs to be told where to forward them to, through an SPI command
("management route") that is valid for only a single frame.
So when we're sending link-local traffic, we are using the
dsa_defer_xmit mechanism.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch provides generic DSA code for using VLAN (802.1Q) tags for
the same purpose as a dedicated switch tag for injection/extraction.
It is based on the discussions and interest that has been so far
expressed in https://www.spinics.net/lists/netdev/msg556125.html.
Unlike all other DSA-supported tagging protocols, CONFIG_NET_DSA_TAG_8021Q
does not offer a complete solution for drivers (nor can it). Instead, it
provides generic code that driver can opt into calling:
- dsa_8021q_xmit: Inserts a VLAN header with the specified contents.
Can be called from another tagging protocol's xmit function.
Currently the LAN9303 driver is inserting headers that are simply
802.1Q with custom fields, so this is an opportunity for code reuse.
- dsa_8021q_rcv: Retrieves the TPID and TCI from a VLAN-tagged skb.
Removing the VLAN header is left as a decision for the caller to make.
- dsa_port_setup_8021q_tagging: For each user port, installs an Rx VID
and a Tx VID, for proper untagged traffic identification on ingress
and steering on egress. Also sets up the VLAN trunk on the upstream
(CPU or DSA) port. Drivers are intentionally left to call this
function explicitly, depending on the context and hardware support.
The expected switch behavior and VLAN semantics should not be violated
under any conditions. That is, after calling
dsa_port_setup_8021q_tagging, the hardware should still pass all
ingress traffic, be it tagged or untagged.
For uniformity with the other tagging protocols, a module for the
dsa_8021q_netdev_ops structure is registered, but the typical usage is
to set up another tagging protocol which selects CONFIG_NET_DSA_TAG_8021Q,
and calls the API from tag_8021q.h. Null function definitions are also
provided so that a "depends on" is not forced in the Kconfig.
This tagging protocol only works when switch ports are standalone, or
when they are added to a VLAN-unaware bridge. It will probably remain
this way for the reasons below.
When added to a bridge that has vlan_filtering 1, the bridge core will
install its own VLANs and reset the pvids through switchdev. For the
bridge core, switchdev is a write-only pipe. All VLAN-related state is
kept in the bridge core and nothing is read from DSA/switchdev or from
the driver. So the bridge core will break this port separation because
it will install the vlan_default_pvid into all switchdev ports.
Even if we could teach the bridge driver about switchdev preference of a
certain vlan_default_pvid (task difficult in itself since the current
setting is per-bridge but we would need it per-port), there would still
exist many other challenges.
Firstly, in the DSA rcv callback, a driver would have to perform an
iterative reverse lookup to find the correct switch port. That is
because the port is a bridge slave, so its Rx VID (port PVID) is subject
to user configuration. How would we ensure that the user doesn't reset
the pvid to a different value (which would make an O(1) translation
impossible), or to a non-unique value within this DSA switch tree (which
would make any translation impossible)?
Finally, not all switch ports are equal in DSA, and that makes it
difficult for the bridge to be completely aware of this anyway.
The CPU port needs to transmit tagged packets (VLAN trunk) in order for
the DSA rcv code to be able to decode source information.
But the bridge code has absolutely no idea which switch port is the CPU
port, if nothing else then just because there is no netdevice registered
by DSA for the CPU port.
Also DSA does not currently allow the user to specify that they want the
CPU port to do VLAN trunking anyway. VLANs are added to the CPU port
using the same flags as they were added on the user port.
So the VLANs installed by dsa_port_setup_8021q_tagging per driver
request should remain private from the bridge's and user's perspective,
and should not alter the VLAN semantics observed by the user.
In the current implementation a VLAN range ending at 4095 (VLAN_N_VID)
is reserved for this purpose. Each port receives a unique Rx VLAN and a
unique Tx VLAN. Separate VLANs are needed for Rx and Tx because they
serve different purposes: on Rx the switch must process traffic as
untagged and process it with a port-based VLAN, but with care not to
hinder bridging. On the other hand, the Tx VLAN is where the
reachability restrictions are imposed, since by tagging frames in the
xmit callback we are telling the switch onto which port to steer the
frame.
Some general guidance on how this support might be employed for
real-life hardware (some comments made by Florian Fainelli):
- If the hardware supports VLAN tag stacking, it should somehow back
up its private VLAN settings when the bridge tries to override them.
Then the driver could re-apply them as outer tags. Dedicating an outer
tag per bridge device would allow identical inner tag VID numbers to
co-exist, yet preserve broadcast domain isolation.
- If the switch cannot handle VLAN tag stacking, it should disable this
port separation when added as slave to a vlan_filtering bridge, in
that case having reduced functionality.
- Drivers for old switches that don't support the entire VLAN_N_VID
range will need to rework the current range selection mechanism.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that all drivers can be probed using more traditional methods,
remove the legacy probe code.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make the CONFIG symbols tristate and add help text.
The broadcom and Microchip KSZ tag drivers support two different
tagging protocols in one driver. Add a configuration option for the
drivers, and then options to select the protocol.
Create a submenu for the tagging drivers.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
v2:
tab/space cleanup
Help text wording
NET_DSA_TAG_BRCM_COMMON and NET_DSA_TAG_KZS_COMMON hidden
v3:
More tabification
Punctuation
v4:
trailler->trailer
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This handles the tag added by the PMAC on the VRX200 SoC line.
The GSWIP uses internally a GSWIP special tag which is located after the
Ethernet header. The PMAC which connects the GSWIP to the CPU converts
this special tag used by the GSWIP into the PMAC special tag which is
added in front of the Ethernet header.
This was tested with GSWIP 2.1 found in the VRX200 SoCs, other GSWIP
versions use slightly different PMAC special tags.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce a configuration option: CONFIG_NET_DSA_LEGACY allowing to compile out
support for the old platform device and Device Tree binding registration.
Support for these configurations is scheduled to be removed in 4.17.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a new type: DSA_TAG_PROTO_PREPEND which allows us to support for the
4-bytes Broadcom tag that we already support, but in a format where it
is pre-pended to the packet instead of located between the MAC SA and
the Ethertyper (DSA_TAG_PROTO_BRCM).
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Files removed in 'net-next' had their license header updated
in 'net'. We take the remove from 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
DSA overrides the master device ethtool ops, so that it can inject stats
from its dedicated switch CPU port as well.
The related code is currently split in dsa.c and slave.c, but it only
scopes the master net device. Move it to a new master.c DSA core file.
This file will be later extented with master net device specific code.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adding support for the Microchip KSZ switch family tail tagging.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Woojung Huh <Woojung.Huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a new port.c file to hold all DSA port-wide logic. This patch moves
in the code which sets a port state.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With more tag protocols being added, regain some order by sorting the
entries in various places.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To define the outgoing port and to discover the incoming port a regular
VLAN tag is used by the LAN9303. But its VID meaning is 'special'.
This tag handler/filter depends on some hardware features which must be
enabled in the device to provide and make use of this special VLAN tag
to control the destination and the source of an ethernet packet.
Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch moves as is the legacy DSA code from dsa.c to legacy.c,
except the few shared symbols which remain in dsa.c.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the support for the 4-bytes tag for DSA port distinguishing inserted
allowing receiving and transmitting the packet via the particular port.
The tag is being added after the source MAC address in the ethernet
header.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Landen Chao <Landen.Chao@mediatek.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While adding switch.o to the list of DSA object files, we essentially
duplicated the previous obj-y line and just added switch.o, remove the
duplicate.
Fixes: f515f192ab4f ("net: dsa: add switch notifier")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a notifier block per DSA switch, registered against a notifier head
in the switch fabric they belong to.
This infrastructure will allow to propagate fabric-wide events such as
port bridging, VLAN configuration, etc. If a DSA switch driver cares
about cross-chip configuration, such events can be caught.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Only the Marvell mv88e6xxx DSA driver made use of the HWMON support in
DSA. The temperature sensor registers are actually in the embedded
PHYs, and the PHY driver now supports it. So remove all HWMON support
from DSA and drivers.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Isolate the HWMON support in DSA in its own file. Currently only the
legacy DSA code is concerned.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for the 2-bytes Qualcomm tag that gigabit switches such as
the QCA8337/N might insert when receiving packets, or that we need
to insert while targeting specific switch ports. The tag is inserted
directly behind the ethernet header.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The existing DSA binding has a number of limitations and problems. The
main problem is that it cannot represent a switch as a linux device,
hanging off some bus. It is limited to one CPU port. The DSA platform
device is artificial, and does not really represent hardware.
Implement a new binding which can be embedded into any type of node on
a bus to represent one switch device, and its links to other switches.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for the 4-bytes Broadcom tag that built-in switches such as
the Starfighter 2 might insert when receiving packets, or that we need
to insert while targetting specific switch ports. We use a fake local
EtherType value for this 4-bytes switch tag: ETH_P_BRCMTAG to make sure
we can assign DSA-specific network operations within the DSA drivers.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Support for specific hardware belongs under drivers/net/ not net/.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change the kconfig types to tristate and adjust the condition for
declaring net_device::dsa_ptr to allow for this.
Adjust the makefile so that if NET_DSA_MV88E6123_61_65=y and
NET_DSA_MV88E6131=m or vice versa then both drivers are built-in. We
could leave these options as bool and make NET_DSA_MV88E6XXX a
user-selected option, but that would break existing configurations.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
These drivers share a lot of code, so if we make them modular they
should be built into the same module. Therefore, link them together
and merge their respective module init and exit functions.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
These files have circular dependencies, so if we make DSA modular then
they must be built into the same module. Therefore, link them
together and merge their respective module init and exit functions.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for the Marvell 88E6060 switch chip. This chip only
supports the Header and Trailer tagging formats, and we use it in
Trailer mode since that mode is slightly easier to handle than
Header mode.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Tested-by: Byron Bradley <byron.bbradley@gmail.com>
Tested-by: Tim Ellis <tim.ellis@mac.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds support for the Trailer switch tagging format. This is
another tagging that doesn't explicitly mark tagged packets with a
distinct ethertype, so that we need to add a similar hack in the
receive path as for the Original DSA tagging format.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Tested-by: Byron Bradley <byron.bbradley@gmail.com>
Tested-by: Tim Ellis <tim.ellis@mac.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for the Marvell 88E6131 switch chip. This chip only
supports the original (ethertype-less) DSA tagging format.
On the 88E6131, there is a PHY Polling Unit (PPU) which has exclusive
access to each of the PHYs's MII management registers. If we want to
talk to the PHYs from software, we have to disable the PPU and wait
for it to complete its current transaction before we can do so, and we
need to re-enable the PPU afterwards to make sure that the switch will
notice changes in link state and speed on the individual ports as they
occur.
Since disabling the PPU is rather slow, and since MII management
accesses are typically done in bursts, this patch keeps the PPU disabled
for 10ms after a software access completes. This makes handling the
PPU slightly more complex, but speeds up something like running ethtool
on one of the switch slave interfaces from ~300ms to ~30ms on typical
hardware.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Tested-by: Nicolas Pitre <nico@marvell.com>
Tested-by: Peter van Valderen <linux@ddcrew.com>
Tested-by: Dirk Teurlings <dirk@upexia.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Most of the DSA switches currently in the field do not support the
Ethertype DSA tagging format that one of the previous patches added
support for, but only the original DSA tagging format.
The original DSA tagging format carries the same information as the
Ethertype DSA tagging format, but with the difference that it does not
have an ethertype field. In other words, when receiving a packet that
is tagged with an original DSA tag, there is no way of telling in
eth_type_trans() that this packet is in fact a DSA-tagged packet.
This patch adds a hook into eth_type_trans() which is only compiled in
if support for a switch chip that doesn't support Ethertype DSA is
selected, and which checks whether there is a DSA switch driver
instance attached to this network device which uses the old tag format.
If so, it sets the protocol field to ETH_P_DSA without looking at the
packet, so that the packet ends up in the right place.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Tested-by: Nicolas Pitre <nico@marvell.com>
Tested-by: Peter van Valderen <linux@ddcrew.com>
Tested-by: Dirk Teurlings <dirk@upexia.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Distributed Switch Architecture is a protocol for managing hardware
switch chips. It consists of a set of MII management registers and
commands to configure the switch, and an ethernet header format to
signal which of the ports of the switch a packet was received from
or is intended to be sent to.
The switches that this driver supports are typically embedded in
access points and routers, and a typical setup with a DSA switch
looks something like this:
+-----------+ +-----------+
| | RGMII | |
| +-------+ +------ 1000baseT MDI ("WAN")
| | | 6-port +------ 1000baseT MDI ("LAN1")
| CPU | | ethernet +------ 1000baseT MDI ("LAN2")
| |MIImgmt| switch +------ 1000baseT MDI ("LAN3")
| +-------+ w/5 PHYs +------ 1000baseT MDI ("LAN4")
| | | |
+-----------+ +-----------+
The switch driver presents each port on the switch as a separate
network interface to Linux, polls the switch to maintain software
link state of those ports, forwards MII management interface
accesses to those network interfaces (e.g. as done by ethtool) to
the switch, and exposes the switch's hardware statistics counters
via the appropriate Linux kernel interfaces.
This initial patch supports the MII management interface register
layout of the Marvell 88E6123, 88E6161 and 88E6165 switch chips, and
supports the "Ethertype DSA" packet tagging format.
(There is no officially registered ethertype for the Ethertype DSA
packet format, so we just grab a random one. The ethertype to use
is programmed into the switch, and the switch driver uses the value
of ETH_P_EDSA for this, so this define can be changed at any time in
the future if the one we chose is allocated to another protocol or
if Ethertype DSA gets its own officially registered ethertype, and
everything will continue to work.)
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Tested-by: Nicolas Pitre <nico@marvell.com>
Tested-by: Byron Bradley <byron.bbradley@gmail.com>
Tested-by: Tim Ellis <tim.ellis@mac.com>
Tested-by: Peter van Valderen <linux@ddcrew.com>
Tested-by: Dirk Teurlings <dirk@upexia.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
