| Age | Commit message (Collapse) | Author |
|---|
|
Adding support for the Microchip KSZ switch family tail tagging.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Woojung Huh <Woojung.Huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With more tag protocols being added, regain some order by sorting the
entries in various places.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To define the outgoing port and to discover the incoming port a regular
VLAN tag is used by the LAN9303. But its VID meaning is 'special'.
This tag handler/filter depends on some hardware features which must be
enabled in the device to provide and make use of this special VLAN tag
to control the destination and the source of an ethernet packet.
Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the support for the 4-bytes tag for DSA port distinguishing inserted
allowing receiving and transmitting the packet via the particular port.
The tag is being added after the source MAC address in the ethernet
header.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Landen Chao <Landen.Chao@mediatek.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After commit 96567d5dacf4 ("net: dsa: dsa2: Add basic support of devlink")
I see the following link error with CONFIG_NET_DSA=y and CONFIG_NET_DEVLINK=m:
net/built-in.o: In function 'dsa_register_switch':
(.text+0xe226b): undefined reference to `devlink_alloc'
net/built-in.o: In function 'dsa_register_switch':
(.text+0xe2284): undefined reference to `devlink_register'
net/built-in.o: In function 'dsa_register_switch':
(.text+0xe243e): undefined reference to `devlink_port_register'
net/built-in.o: In function 'dsa_register_switch':
(.text+0xe24e1): undefined reference to `devlink_port_register'
net/built-in.o: In function 'dsa_register_switch':
(.text+0xe24fa): undefined reference to `devlink_port_type_eth_set'
net/built-in.o: In function 'dsa_dst_unapply.part.8':
dsa2.c:(.text.unlikely+0x345): undefined reference to 'devlink_port_unregister'
dsa2.c:(.text.unlikely+0x36c): undefined reference to 'devlink_port_unregister'
dsa2.c:(.text.unlikely+0x38e): undefined reference to 'devlink_port_unregister'
dsa2.c:(.text.unlikely+0x3f2): undefined reference to 'devlink_unregister'
dsa2.c:(.text.unlikely+0x3fb): undefined reference to 'devlink_free'
Fix this by adding a dependency on MAY_USE_DEVLINK so that CONFIG_NET_DSA
get switched to be build as module when CONFIG_NET_DEVLINK=m.
Fixes: 96567d5dacf4 ("net: dsa: dsa2: Add basic support of devlink")
Signed-off-by: Tobias Regnery <tobias.regnery@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Only the Marvell mv88e6xxx DSA driver made use of the HWMON support in
DSA. The temperature sensor registers are actually in the embedded
PHYs, and the PHY driver now supports it. So remove all HWMON support
from DSA and drivers.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The support for DSA Ethernet switch chips depends on TCP/IP networking,
thus explicit that HAVE_NET_DSA depends on INET.
DSA uses SWITCHDEV, thus select it instead of depending on it.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for the 2-bytes Qualcomm tag that gigabit switches such as
the QCA8337/N might insert when receiving packets, or that we need
to insert while targeting specific switch ports. The tag is inserted
directly behind the ethernet header.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change bd76a116707bd2381da36cf7c3183df11293f1d6 made all DSA drivers
depend on NET_DSA rather than selecting them. However, as the only way
to select this option was to actually select a driver, it made DSA
impossible to enable at all.
This patch adds an explicit entry which the user will have to enable
prior selecting a driver.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This would fix randconfig compile error:
net/built-in.o: In function `netdev_switch_fib_ipv4_abort':
(.text+0xf7811): undefined reference to `fib_flush_external'
Also it fixes following warnings:
warning: (NET_DSA) selects NET_SWITCHDEV which has unmet direct dependencies (NET && INET)
warning: (NET_DSA_MV88E6060 && NET_DSA_MV88E6131 && NET_DSA_MV88E6123_61_65 && NET_DSA_MV88E6171 && NET_DSA_MV88E6352 && NET_DSA_BCM_SF2) selects NET_DSA which has unmet direct dependencies (NET && HAVE_NET_DSA && NET_SWITCHDEV)
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Suggested-by: Alexei Starovoitov <alexei.starovoitov@gmail.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to support bridging offloads in DSA switch drivers, select
NET_SWITCHDEV to get access to the port_stp_update and parent_get_id
NDOs that we are required to implement.
To facilitate the integratation at the DSA driver level, we implement 3
types of operations:
- port_join_bridge
- port_leave_bridge
- port_stp_update
DSA will resolve which switch ports that are currently bridge port
members as some Switch hardware/drivers need to know about that to limit
the register programming to just the relevant registers (especially for
slow MDIO buses).
We also take care of setting the correct STP state when slave network
devices are brought up/down while being bridge members.
Finally, when a port is leaving the bridge, we make sure we set in
BR_STATE_FORWARDING state, otherwise the bridge layer would leave it
disabled as a result of having left the bridge.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some switches provide chip temperature data.
Add support for reporting it through the hwmon subsystem.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for the 4-bytes Broadcom tag that built-in switches such as
the Starfighter 2 might insert when receiving packets, or that we need
to insert while targetting specific switch ports. We use a fake local
EtherType value for this 4-bytes switch tag: ETH_P_BRCMTAG to make sure
we can assign DSA-specific network operations within the DSA drivers.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 82167cb8c6b2f8166d5c7532e5ef4b5e0cc46a72 ('net: dsa/slave: Fix
compilation warnings') fixed one possible invalid configuration
(NET_DSA enabled with no trailer formats) but added others: drivers
can select NET_DSA without its dependencies being met.
It's not very useful to make either the DSA core or the tagging
formats manually selectable without a driver to use them, so:
1. Define a hidden HAVE_NET_DSA option and move the dependencies of
NET_DSA to that. While we're at it, drop the deprecated
EXPERIMENTAL dependency.
2. Make NET_DSA and the drivers dependent on HAVE_NET_DSA.
3. Hide the tagging format options again.
4. Make drivers select both NET_DSA and the appropriate tagging format
option.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently when none of CONFIG_NET_DSA_TAG_DSA, CONFIG_NET_DSA_TAG_EDSA and
CONFIG_NET_DSA_TAG_TRAILER is defined, we get following compilation warnings:
net/dsa/slave.c:51:12: warning: 'dsa_slave_init' defined but not used [-Wunused-function]
net/dsa/slave.c:60:12: warning: 'dsa_slave_open' defined but not used [-Wunused-function]
net/dsa/slave.c:98:12: warning: 'dsa_slave_close' defined but not used [-Wunused-function]
net/dsa/slave.c:116:13: warning: 'dsa_slave_change_rx_flags' defined but not used [-Wunused-function]
net/dsa/slave.c:127:13: warning: 'dsa_slave_set_rx_mode' defined but not used [-Wunused-function]
net/dsa/slave.c:136:12: warning: 'dsa_slave_set_mac_address' defined but not used [-Wunused-function]
net/dsa/slave.c:164:12: warning: 'dsa_slave_ioctl' defined but not used [-Wunused-function]
Earlier approach to fix this was discussed here:
lkml.org/lkml/2012/10/29/549
This is another approach to fix it. This is done by some changes in config
options, which make more sense than the earlier approach. As, atleast one
tagging option must always be selected for using net/dsa/ infrastructure, this
patch selects NET_DSA from tagging configs instead of having it as an selectable
config.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Support for specific hardware belongs under drivers/net/ not net/.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change the kconfig types to tristate and adjust the condition for
declaring net_device::dsa_ptr to allow for this.
Adjust the makefile so that if NET_DSA_MV88E6123_61_65=y and
NET_DSA_MV88E6131=m or vice versa then both drivers are built-in. We
could leave these options as bool and make NET_DSA_MV88E6XXX a
user-selected option, but that would break existing configurations.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The 88e6085 has a few differences from the other devices in the port
control registers, causing unknown multicast/broadcast packets to get
dropped when using the standard port setup.
At the same time update kconfig to clarify that the mv88e6085 is now
supported.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Several gigabit network drivers (SB1250_MAC, TIGON3, FSL, GIANFAR,
UCC_GETH, MV643XX_ETH, XILINX_LL_TEMAC, S6GMAC, STMMAC_ETH, PASEMI_MAC,
and OCTEON_ETHERNET) select PHYLIB. These drivers are not under
NET_ETHERNET (10/100 mbit), so this warning is generated (long, irrelevant
parts are omitted):
warning: (NET_DSA && NET && EXPERIMENTAL && NET_ETHERNET && !S390 || ... || SB1250_MAC && NETDEVICES && NETDEV_1000 && SIBYTE_SB1xxx_SOC || TIGON3 && NETDEVICES && NETDEV_1000 && PCI || FSL_PQ_MDIO && NETDEVICES && NETDEV_1000 && FSL_SOC || GIANFAR && NETDEVICES && NETDEV_1000 && FSL_SOC || UCC_GETH && NETDEVICES && NETDEV_1000 && QUICC_ENGINE || MV643XX_ETH && NETDEVICES && NETDEV_1000 && (MV64X60 || PPC32 || PLAT_ORION) || XILINX_LL_TEMAC && NETDEVICES && NETDEV_1000 && (PPC || MICROBLAZE) || S6GMAC && NETDEVICES && NETDEV_1000 && XTENSA_VARIANT_S6000 || STMMAC_ETH && NETDEV_1000 && NETDEVICES && CPU_SUBTYPE_ST40 || PASEMI_MAC && NETDEVICES && NETDEV_10000 && PPC_PASEMI && PCI || OCTEON_ETHERNET && STAGING && !STAGING_EXCLUDE_BUILD && CPU_CAVIUM_OCTEON) selects PHYLIB which has unmet direct dependencies (!S390 && NET_ETHERNET)
PHYLIB is used by non-10/100 mbit ethernet drivers, so change the dependencies
to be NETDEVICES instead of NET_ETHERNET.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Based upon a report by Randy Dunlap.
DSA needs PHYLIB, but PHYLIB needs NET_ETHERNET. So, in order
to select PHYLIB we have to make DSA depend upon NET_ETHERNET.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for the Marvell 88E6095/6095F switch chips. These
chips are similar to the 88e6131, so we can add the support to
mv88e6131.c easily.
Thanks to Gary Thomas <gary@mlbassoc.com> and Jesper Dangaard
Brouer <hawk@diku.dk> for testing various patches.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Tested-by: Gary Thomas <gary@mlbassoc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git commit 45cec1bac0719c904bb5f4405c2937f7e715888c
"dsa: Need to select PHYLIB." causes this build bug on s390:
drivers/built-in.o: In function `phy_stop_interrupts':
/home/heicarst/linux-2.6/drivers/net/phy/phy.c:631: undefined reference to `free_irq'
/home/heicarst/linux-2.6/drivers/net/phy/phy.c:646: undefined reference to `enable_irq'
drivers/built-in.o: In function `phy_start_interrupts':
/home/heicarst/linux-2.6/drivers/net/phy/phy.c:601: undefined reference to `request_irq'
drivers/built-in.o: In function `phy_interrupt':
/home/heicarst/linux-2.6/drivers/net/phy/phy.c:528: undefined reference to `disable_irq_nosync'
drivers/built-in.o: In function `phy_change':
/home/heicarst/linux-2.6/drivers/net/phy/phy.c:674: undefined reference to `enable_irq'
/home/heicarst/linux-2.6/drivers/net/phy/phy.c:692: undefined reference to `disable_irq'
PHYLIB has alread a depend on !S390, however select PHYLIB at DSA overrides
that unfortunately. So add a depend on !S390 to DSA as well.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for the Marvell 88E6060 switch chip. This chip only
supports the Header and Trailer tagging formats, and we use it in
Trailer mode since that mode is slightly easier to handle than
Header mode.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Tested-by: Byron Bradley <byron.bbradley@gmail.com>
Tested-by: Tim Ellis <tim.ellis@mac.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds support for the Trailer switch tagging format. This is
another tagging that doesn't explicitly mark tagged packets with a
distinct ethertype, so that we need to add a similar hack in the
receive path as for the Original DSA tagging format.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Tested-by: Byron Bradley <byron.bbradley@gmail.com>
Tested-by: Tim Ellis <tim.ellis@mac.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for the Marvell 88E6131 switch chip. This chip only
supports the original (ethertype-less) DSA tagging format.
On the 88E6131, there is a PHY Polling Unit (PPU) which has exclusive
access to each of the PHYs's MII management registers. If we want to
talk to the PHYs from software, we have to disable the PPU and wait
for it to complete its current transaction before we can do so, and we
need to re-enable the PPU afterwards to make sure that the switch will
notice changes in link state and speed on the individual ports as they
occur.
Since disabling the PPU is rather slow, and since MII management
accesses are typically done in bursts, this patch keeps the PPU disabled
for 10ms after a software access completes. This makes handling the
PPU slightly more complex, but speeds up something like running ethtool
on one of the switch slave interfaces from ~300ms to ~30ms on typical
hardware.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Tested-by: Nicolas Pitre <nico@marvell.com>
Tested-by: Peter van Valderen <linux@ddcrew.com>
Tested-by: Dirk Teurlings <dirk@upexia.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Most of the DSA switches currently in the field do not support the
Ethertype DSA tagging format that one of the previous patches added
support for, but only the original DSA tagging format.
The original DSA tagging format carries the same information as the
Ethertype DSA tagging format, but with the difference that it does not
have an ethertype field. In other words, when receiving a packet that
is tagged with an original DSA tag, there is no way of telling in
eth_type_trans() that this packet is in fact a DSA-tagged packet.
This patch adds a hook into eth_type_trans() which is only compiled in
if support for a switch chip that doesn't support Ethertype DSA is
selected, and which checks whether there is a DSA switch driver
instance attached to this network device which uses the old tag format.
If so, it sets the protocol field to ETH_P_DSA without looking at the
packet, so that the packet ends up in the right place.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Tested-by: Nicolas Pitre <nico@marvell.com>
Tested-by: Peter van Valderen <linux@ddcrew.com>
Tested-by: Dirk Teurlings <dirk@upexia.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Distributed Switch Architecture is a protocol for managing hardware
switch chips. It consists of a set of MII management registers and
commands to configure the switch, and an ethernet header format to
signal which of the ports of the switch a packet was received from
or is intended to be sent to.
The switches that this driver supports are typically embedded in
access points and routers, and a typical setup with a DSA switch
looks something like this:
+-----------+ +-----------+
| | RGMII | |
| +-------+ +------ 1000baseT MDI ("WAN")
| | | 6-port +------ 1000baseT MDI ("LAN1")
| CPU | | ethernet +------ 1000baseT MDI ("LAN2")
| |MIImgmt| switch +------ 1000baseT MDI ("LAN3")
| +-------+ w/5 PHYs +------ 1000baseT MDI ("LAN4")
| | | |
+-----------+ +-----------+
The switch driver presents each port on the switch as a separate
network interface to Linux, polls the switch to maintain software
link state of those ports, forwards MII management interface
accesses to those network interfaces (e.g. as done by ethtool) to
the switch, and exposes the switch's hardware statistics counters
via the appropriate Linux kernel interfaces.
This initial patch supports the MII management interface register
layout of the Marvell 88E6123, 88E6161 and 88E6165 switch chips, and
supports the "Ethertype DSA" packet tagging format.
(There is no officially registered ethertype for the Ethertype DSA
packet format, so we just grab a random one. The ethertype to use
is programmed into the switch, and the switch driver uses the value
of ETH_P_EDSA for this, so this define can be changed at any time in
the future if the one we chose is allocated to another protocol or
if Ethertype DSA gets its own officially registered ethertype, and
everything will continue to work.)
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Tested-by: Nicolas Pitre <nico@marvell.com>
Tested-by: Byron Bradley <byron.bbradley@gmail.com>
Tested-by: Tim Ellis <tim.ellis@mac.com>
Tested-by: Peter van Valderen <linux@ddcrew.com>
Tested-by: Dirk Teurlings <dirk@upexia.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
