| Age | Commit message (Collapse) | Author |
|---|
|
Replace the existing /* fall through */ comments and its variants with
the new pseudo-keyword macro fallthrough[1]. Also, remove unnecessary
fall-through markings when it is the case.
[1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
|
|
Alexei Starovoitov says:
====================
pull-request: bpf 2020-08-21
The following pull-request contains BPF updates for your *net* tree.
We've added 11 non-merge commits during the last 5 day(s) which contain
a total of 12 files changed, 78 insertions(+), 24 deletions(-).
The main changes are:
1) three fixes in BPF task iterator logic, from Yonghong.
2) fix for compressed dwarf sections in vmlinux, from Jiri.
3) fix xdp attach regression, from Andrii.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
7f0a838254bd ("bpf, xdp: Maintain info on attached XDP BPF programs in net_device")
inadvertently changed which XDP mode is assumed when no mode flags are
specified explicitly. Previously, driver mode was preferred, if driver
supported it. If not, generic SKB mode was chosen. That commit changed default
to SKB mode always. This patch fixes the issue and restores the original
logic.
Fixes: 7f0a838254bd ("bpf, xdp: Maintain info on attached XDP BPF programs in net_device")
Reported-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Tested-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/bpf/20200820052841.1559757-1-andriin@fb.com
|
|
pskb_carve_frag_list() may return -ENOMEM in pskb_carve_inside_nonlinear().
we should handle this correctly or we would get wrong sk_buff.
Fixes: 6fa01ccd8830 ("skbuff: Add pskb_extract() helper function")
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit f8414a8d886b613b90d9fdf7cda6feea313b1069.
eth_type_trans() does the necessary pull on the skb.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It is possible to trigger this WARN_ON from user space by triggering a
devlink snapshot with an ID which already exists. We don't need both
-EEXISTS being reported and spamming the kernel log.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We may access the two bytes after vlan_hdr in vlan_set_encap_proto(). So
we should pull VLAN_HLEN + sizeof(unsigned short) in skb_vlan_untag() or
we may access the wrong data.
Fixes: 0d5501c1c828 ("net: Always untag vlan-tagged traffic on input.")
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When an XDP program changes the ethernet header protocol field,
eth_type_trans is used to recalculate skb->protocol. In order for
eth_type_trans to work correctly, the ethernet header must actually be
part of the skb data segment, so the code first pushes that onto the
head of the skb. However, it subsequently forgets to pull it back off,
making the behavior of the passed-on packet inconsistent between the
protocol modifying case and the static protocol case. This patch fixes
the issue by simply pulling the ethernet header back off of the skb
head.
Fixes: 297249569932 ("net: fix generic XDP to handle if eth header was mangled")
Cc: Jesper Dangaard Brouer <brouer@redhat.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Daniel Borkmann says:
====================
pull-request: bpf 2020-08-15
The following pull-request contains BPF updates for your *net* tree.
We've added 23 non-merge commits during the last 4 day(s) which contain
a total of 32 files changed, 421 insertions(+), 141 deletions(-).
The main changes are:
1) Fix sock_ops ctx access splat due to register override, from John Fastabend.
2) Batch of various fixes to libbpf, bpftool, and selftests when testing build
in 32-bit mode, from Andrii Nakryiko.
3) Fix vmlinux.h generation on ARM by mapping GCC built-in types (__Poly*_t)
to equivalent ones clang can work with, from Jean-Philippe Brucker.
4) Fix build_id lookup in bpf_get_stackid() helper by walking all NOTE ELF
sections instead of just first, from Jiri Olsa.
5) Avoid use of __builtin_offsetof() in libbpf for CO-RE, from Yonghong Song.
6) Fix segfault in test_mmap due to inconsistent length params, from Jianlin Lv.
7) Don't override errno in libbpf when logging errors, from Toke Høiland-Jørgensen.
8) Fix v4_to_v6 sockaddr conversion in sk_lookup test, from Stanislav Fomichev.
9) Add link to bpf-helpers(7) man page to BPF doc, from Joe Stringer.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes from David Miller:
"Some merge window fallout, some longer term fixes:
1) Handle headroom properly in lapbether and x25_asy drivers, from
Xie He.
2) Fetch MAC address from correct r8152 device node, from Thierry
Reding.
3) In the sw kTLS path we should allow MSG_CMSG_COMPAT in sendmsg,
from Rouven Czerwinski.
4) Correct fdputs in socket layer, from Miaohe Lin.
5) Revert troublesome sockptr_t optimization, from Christoph Hellwig.
6) Fix TCP TFO key reading on big endian, from Jason Baron.
7) Missing CAP_NET_RAW check in nfc, from Qingyu Li.
8) Fix inet fastreuse optimization with tproxy sockets, from Tim
Froidcoeur.
9) Fix 64-bit divide in new SFC driver, from Edward Cree.
10) Add a tracepoint for prandom_u32 so that we can more easily
perform usage analysis. From Eric Dumazet.
11) Fix rwlock imbalance in AF_PACKET, from John Ogness"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (49 commits)
net: openvswitch: introduce common code for flushing flows
af_packet: TPACKET_V3: fix fill status rwlock imbalance
random32: add a tracepoint for prandom_u32()
Revert "ipv4: tunnel: fix compilation on ARCH=um"
net: accept an empty mask in /sys/class/net/*/queues/rx-*/rps_cpus
net: ethernet: stmmac: Disable hardware multicast filter
net: stmmac: dwmac1000: provide multicast filter fallback
ipv4: tunnel: fix compilation on ARCH=um
vsock: fix potential null pointer dereference in vsock_poll()
sfc: fix ef100 design-param checking
net: initialize fastreuse on inet_inherit_port
net: refactor bind_bucket fastreuse into helper
net: phy: marvell10g: fix null pointer dereference
net: Fix potential memory leak in proto_register()
net: qcom/emac: add missed clk_disable_unprepare in error path of emac_clks_phase1_init
ionic_lif: Use devm_kcalloc() in ionic_qcq_alloc()
net/nfc/rawsock.c: add CAP_NET_RAW check.
hinic: fix strncpy output truncated compile warnings
drivers/net/wan/x25_asy: Added needed_headroom and a skb->len check
net/tls: Fix kmap usage
...
|
|
Similar to patch ("bpf: sock_ops ctx access may stomp registers") if the
src_reg = dst_reg when reading the sk field of a sock_ops struct we
generate xlated code,
53: (61) r9 = *(u32 *)(r9 +28)
54: (15) if r9 == 0x0 goto pc+3
56: (79) r9 = *(u64 *)(r9 +0)
This stomps on the r9 reg to do the sk_fullsock check and then when
reading the skops->sk field instead of the sk pointer we get the
sk_fullsock. To fix use similar pattern noted in the previous fix
and use the temp field to save/restore a register used to do
sk_fullsock check.
After the fix the generated xlated code reads,
52: (7b) *(u64 *)(r9 +32) = r8
53: (61) r8 = *(u32 *)(r9 +28)
54: (15) if r9 == 0x0 goto pc+3
55: (79) r8 = *(u64 *)(r9 +32)
56: (79) r9 = *(u64 *)(r9 +0)
57: (05) goto pc+1
58: (79) r8 = *(u64 *)(r9 +32)
Here r9 register was in-use so r8 is chosen as the temporary register.
In line 52 r8 is saved in temp variable and at line 54 restored in case
fullsock != 0. Finally we handle fullsock == 0 case by restoring at
line 58.
This adds a new macro SOCK_OPS_GET_SK it is almost possible to merge
this with SOCK_OPS_GET_FIELD, but I found the extra branch logic a
bit more confusing than just adding a new macro despite a bit of
duplicating code.
Fixes: 1314ef561102e ("bpf: export bpf_sock for BPF_PROG_TYPE_SOCK_OPS prog type")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Song Liu <songliubraving@fb.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/159718349653.4728.6559437186853473612.stgit@john-Precision-5820-Tower
|
|
I had a sockmap program that after doing some refactoring started spewing
this splat at me:
[18610.807284] BUG: unable to handle kernel NULL pointer dereference at 0000000000000001
[...]
[18610.807359] Call Trace:
[18610.807370] ? 0xffffffffc114d0d5
[18610.807382] __cgroup_bpf_run_filter_sock_ops+0x7d/0xb0
[18610.807391] tcp_connect+0x895/0xd50
[18610.807400] tcp_v4_connect+0x465/0x4e0
[18610.807407] __inet_stream_connect+0xd6/0x3a0
[18610.807412] ? __inet_stream_connect+0x5/0x3a0
[18610.807417] inet_stream_connect+0x3b/0x60
[18610.807425] __sys_connect+0xed/0x120
After some debugging I was able to build this simple reproducer,
__section("sockops/reproducer_bad")
int bpf_reproducer_bad(struct bpf_sock_ops *skops)
{
volatile __maybe_unused __u32 i = skops->snd_ssthresh;
return 0;
}
And along the way noticed that below program ran without splat,
__section("sockops/reproducer_good")
int bpf_reproducer_good(struct bpf_sock_ops *skops)
{
volatile __maybe_unused __u32 i = skops->snd_ssthresh;
volatile __maybe_unused __u32 family;
compiler_barrier();
family = skops->family;
return 0;
}
So I decided to check out the code we generate for the above two
programs and noticed each generates the BPF code you would expect,
0000000000000000 <bpf_reproducer_bad>:
; volatile __maybe_unused __u32 i = skops->snd_ssthresh;
0: r1 = *(u32 *)(r1 + 96)
1: *(u32 *)(r10 - 4) = r1
; return 0;
2: r0 = 0
3: exit
0000000000000000 <bpf_reproducer_good>:
; volatile __maybe_unused __u32 i = skops->snd_ssthresh;
0: r2 = *(u32 *)(r1 + 96)
1: *(u32 *)(r10 - 4) = r2
; family = skops->family;
2: r1 = *(u32 *)(r1 + 20)
3: *(u32 *)(r10 - 8) = r1
; return 0;
4: r0 = 0
5: exit
So we get reasonable assembly, but still something was causing the null
pointer dereference. So, we load the programs and dump the xlated version
observing that line 0 above 'r* = *(u32 *)(r1 +96)' is going to be
translated by the skops access helpers.
int bpf_reproducer_bad(struct bpf_sock_ops * skops):
; volatile __maybe_unused __u32 i = skops->snd_ssthresh;
0: (61) r1 = *(u32 *)(r1 +28)
1: (15) if r1 == 0x0 goto pc+2
2: (79) r1 = *(u64 *)(r1 +0)
3: (61) r1 = *(u32 *)(r1 +2340)
; volatile __maybe_unused __u32 i = skops->snd_ssthresh;
4: (63) *(u32 *)(r10 -4) = r1
; return 0;
5: (b7) r0 = 0
6: (95) exit
int bpf_reproducer_good(struct bpf_sock_ops * skops):
; volatile __maybe_unused __u32 i = skops->snd_ssthresh;
0: (61) r2 = *(u32 *)(r1 +28)
1: (15) if r2 == 0x0 goto pc+2
2: (79) r2 = *(u64 *)(r1 +0)
3: (61) r2 = *(u32 *)(r2 +2340)
; volatile __maybe_unused __u32 i = skops->snd_ssthresh;
4: (63) *(u32 *)(r10 -4) = r2
; family = skops->family;
5: (79) r1 = *(u64 *)(r1 +0)
6: (69) r1 = *(u16 *)(r1 +16)
; family = skops->family;
7: (63) *(u32 *)(r10 -8) = r1
; return 0;
8: (b7) r0 = 0
9: (95) exit
Then we look at lines 0 and 2 above. In the good case we do the zero
check in r2 and then load 'r1 + 0' at line 2. Do a quick cross-check
into the bpf_sock_ops check and we can confirm that is the 'struct
sock *sk' pointer field. But, in the bad case,
0: (61) r1 = *(u32 *)(r1 +28)
1: (15) if r1 == 0x0 goto pc+2
2: (79) r1 = *(u64 *)(r1 +0)
Oh no, we read 'r1 +28' into r1, this is skops->fullsock and then in
line 2 we read the 'r1 +0' as a pointer. Now jumping back to our spat,
[18610.807284] BUG: unable to handle kernel NULL pointer dereference at 0000000000000001
The 0x01 makes sense because that is exactly the fullsock value. And
its not a valid dereference so we splat.
To fix we need to guard the case when a program is doing a sock_ops field
access with src_reg == dst_reg. This is already handled in the load case
where the ctx_access handler uses a tmp register being careful to
store the old value and restore it. To fix the get case test if
src_reg == dst_reg and in this case do the is_fullsock test in the
temporary register. Remembering to restore the temporary register before
writing to either dst_reg or src_reg to avoid smashing the pointer into
the struct holding the tmp variable.
Adding this inline code to test_tcpbpf_kern will now be generated
correctly from,
9: r2 = *(u32 *)(r2 + 96)
to xlated code,
12: (7b) *(u64 *)(r2 +32) = r9
13: (61) r9 = *(u32 *)(r2 +28)
14: (15) if r9 == 0x0 goto pc+4
15: (79) r9 = *(u64 *)(r2 +32)
16: (79) r2 = *(u64 *)(r2 +0)
17: (61) r2 = *(u32 *)(r2 +2348)
18: (05) goto pc+1
19: (79) r9 = *(u64 *)(r2 +32)
And in the normal case we keep the original code, because really this
is an edge case. From this,
9: r2 = *(u32 *)(r6 + 96)
to xlated code,
22: (61) r2 = *(u32 *)(r6 +28)
23: (15) if r2 == 0x0 goto pc+2
24: (79) r2 = *(u64 *)(r6 +0)
25: (61) r2 = *(u32 *)(r2 +2348)
So three additional instructions if dst == src register, but I scanned
my current code base and did not see this pattern anywhere so should
not be a big deal. Further, it seems no one else has hit this or at
least reported it so it must a fairly rare pattern.
Fixes: 9b1f3d6e5af29 ("bpf: Refactor sock_ops_convert_ctx_access")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Song Liu <songliubraving@fb.com>
Acked-by: Martin KaFai Lau <kafai@fb.com>
Link: https://lore.kernel.org/bpf/159718347772.4728.2781381670567919577.stgit@john-Precision-5820-Tower
|
|
Enforce XDP_FLAGS_UPDATE_IF_NOEXIST only if new BPF program to be attached is
non-NULL (i.e., we are not detaching a BPF program).
Fixes: d4baa9368a5e ("bpf, xdp: Extract common XDP program attachment logic")
Reported-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Tested-by: Stanislav Fomichev <sdf@google.com>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/bpf/20200812022923.1217922-1-andriin@fb.com
|
|
We must accept an empty mask in store_rps_map(), or we are not able
to disable RPS on a queue.
Fixes: 07bbecb34106 ("net: Restrict receive packets queuing to housekeeping CPUs")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Maciej Żenczykowski <maze@google.com>
Cc: Alex Belits <abelits@marvell.com>
Cc: Nitesh Narayan Lal <nitesh@redhat.com>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Maciej Żenczykowski <maze@google.com>
Acked-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Nitesh Narayan Lal <nitesh@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If we failed to assign proto idx, we free the twsk_slab_name but forget to
free the twsk_slab. Add a helper function tw_prot_cleanup() to free these
together and also use this helper function in proto_unregister().
Fixes: b45ce32135d1 ("sock: fix potential memory leak in proto_register()")
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use helper function ip_is_fragment() to check ip fragment.
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Merge misc updates from Andrew Morton:
- a few MM hotfixes
- kthread, tools, scripts, ntfs and ocfs2
- some of MM
Subsystems affected by this patch series: kthread, tools, scripts, ntfs,
ocfs2 and mm (hofixes, pagealloc, slab-generic, slab, slub, kcsan,
debug, pagecache, gup, swap, shmem, memcg, pagemap, mremap, mincore,
sparsemem, vmalloc, kasan, pagealloc, hugetlb and vmscan).
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (162 commits)
mm: vmscan: consistent update to pgrefill
mm/vmscan.c: fix typo
khugepaged: khugepaged_test_exit() check mmget_still_valid()
khugepaged: retract_page_tables() remember to test exit
khugepaged: collapse_pte_mapped_thp() protect the pmd lock
khugepaged: collapse_pte_mapped_thp() flush the right range
mm/hugetlb: fix calculation of adjust_range_if_pmd_sharing_possible
mm: thp: replace HTTP links with HTTPS ones
mm/page_alloc: fix memalloc_nocma_{save/restore} APIs
mm/page_alloc.c: skip setting nodemask when we are in interrupt
mm/page_alloc: fallbacks at most has 3 elements
mm/page_alloc: silence a KASAN false positive
mm/page_alloc.c: remove unnecessary end_bitidx for [set|get]_pfnblock_flags_mask()
mm/page_alloc.c: simplify pageblock bitmap access
mm/page_alloc.c: extract the common part in pfn_to_bitidx()
mm/page_alloc.c: replace the definition of NR_MIGRATETYPE_BITS with PB_migratetype_bits
mm/shuffle: remove dynamic reconfiguration
mm/memory_hotplug: document why shuffle_zone() is relevant
mm/page_alloc: remove nr_free_pagecache_pages()
mm: remove vm_total_pages
...
|
|
As said by Linus:
A symmetric naming is only helpful if it implies symmetries in use.
Otherwise it's actively misleading.
In "kzalloc()", the z is meaningful and an important part of what the
caller wants.
In "kzfree()", the z is actively detrimental, because maybe in the
future we really _might_ want to use that "memfill(0xdeadbeef)" or
something. The "zero" part of the interface isn't even _relevant_.
The main reason that kzfree() exists is to clear sensitive information
that should not be leaked to other future users of the same memory
objects.
Rename kzfree() to kfree_sensitive() to follow the example of the recently
added kvfree_sensitive() and make the intention of the API more explicit.
In addition, memzero_explicit() is used to clear the memory to make sure
that it won't get optimized away by the compiler.
The renaming is done by using the command sequence:
git grep -w --name-only kzfree |\
xargs sed -i 's/kzfree/kfree_sensitive/'
followed by some editing of the kfree_sensitive() kerneldoc and adding
a kzfree backward compatibility macro in slab.h.
[akpm@linux-foundation.org: fs/crypto/inline_crypt.c needs linux/slab.h]
[akpm@linux-foundation.org: fix fs/crypto/inline_crypt.c some more]
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Waiman Long <longman@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: David Howells <dhowells@redhat.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Cc: James Morris <jmorris@namei.org>
Cc: "Serge E. Hallyn" <serge@hallyn.com>
Cc: Joe Perches <joe@perches.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Dan Carpenter <dan.carpenter@oracle.com>
Cc: "Jason A . Donenfeld" <Jason@zx2c4.com>
Link: http://lkml.kernel.org/r/20200616154311.12314-3-longman@redhat.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/teigland/linux-dlm
Pull dlm updates from David Teigland:
"This set includes a some improvements to the dlm networking layer:
improving the ability to trace dlm messages for debugging, and
improved handling of bad messages or disrupted connections"
* tag 'dlm-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/teigland/linux-dlm:
fs: dlm: implement tcp graceful shutdown
fs: dlm: change handling of reconnects
fs: dlm: don't close socket on invalid message
fs: dlm: set skb mark per peer socket
fs: dlm: set skb mark for listen socket
net: sock: add sock_set_mark
dlm: Fix kobject memleak
|
|
Commit a5cbe05a6673 ("bpf: Implement bpf iterator for
map elements") added bpf iterator support for
map elements. The map element bpf iterator requires
info to identify a particular map. In the above
commit, the attr->link_create.target_fd is used
to carry map_fd and an enum bpf_iter_link_info
is added to uapi to specify the target_fd actually
representing a map_fd:
enum bpf_iter_link_info {
BPF_ITER_LINK_UNSPEC = 0,
BPF_ITER_LINK_MAP_FD = 1,
MAX_BPF_ITER_LINK_INFO,
};
This is an extensible approach as we can grow
enumerator for pid, cgroup_id, etc. and we can
unionize target_fd for pid, cgroup_id, etc.
But in the future, there are chances that
more complex customization may happen, e.g.,
for tasks, it could be filtered based on
both cgroup_id and user_id.
This patch changed the uapi to have fields
__aligned_u64 iter_info;
__u32 iter_info_len;
for additional iter_info for link_create.
The iter_info is defined as
union bpf_iter_link_info {
struct {
__u32 map_fd;
} map;
};
So future extension for additional customization
will be easier. The bpf_iter_link_info will be
passed to target callback to validate and generic
bpf_iter framework does not need to deal it any
more.
Note that map_fd = 0 will be considered invalid
and -EBADF will be returned to user space.
Fixes: a5cbe05a6673 ("bpf: Implement bpf iterator for map elements")
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20200805055056.1457463-1-yhs@fb.com
|
|
This patch adds a new socket helper function to set the mark value for a
kernel socket.
Signed-off-by: Alexander Aring <aahringo@redhat.com>
Signed-off-by: David Teigland <teigland@redhat.com>
|
|
Pull networking updates from David Miller:
1) Support 6Ghz band in ath11k driver, from Rajkumar Manoharan.
2) Support UDP segmentation in code TSO code, from Eric Dumazet.
3) Allow flashing different flash images in cxgb4 driver, from Vishal
Kulkarni.
4) Add drop frames counter and flow status to tc flower offloading,
from Po Liu.
5) Support n-tuple filters in cxgb4, from Vishal Kulkarni.
6) Various new indirect call avoidance, from Eric Dumazet and Brian
Vazquez.
7) Fix BPF verifier failures on 32-bit pointer arithmetic, from
Yonghong Song.
8) Support querying and setting hardware address of a port function via
devlink, use this in mlx5, from Parav Pandit.
9) Support hw ipsec offload on bonding slaves, from Jarod Wilson.
10) Switch qca8k driver over to phylink, from Jonathan McDowell.
11) In bpftool, show list of processes holding BPF FD references to
maps, programs, links, and btf objects. From Andrii Nakryiko.
12) Several conversions over to generic power management, from Vaibhav
Gupta.
13) Add support for SO_KEEPALIVE et al. to bpf_setsockopt(), from Dmitry
Yakunin.
14) Various https url conversions, from Alexander A. Klimov.
15) Timestamping and PHC support for mscc PHY driver, from Antoine
Tenart.
16) Support bpf iterating over tcp and udp sockets, from Yonghong Song.
17) Support 5GBASE-T i40e NICs, from Aleksandr Loktionov.
18) Add kTLS RX HW offload support to mlx5e, from Tariq Toukan.
19) Fix the ->ndo_start_xmit() return type to be netdev_tx_t in several
drivers. From Luc Van Oostenryck.
20) XDP support for xen-netfront, from Denis Kirjanov.
21) Support receive buffer autotuning in MPTCP, from Florian Westphal.
22) Support EF100 chip in sfc driver, from Edward Cree.
23) Add XDP support to mvpp2 driver, from Matteo Croce.
24) Support MPTCP in sock_diag, from Paolo Abeni.
25) Commonize UDP tunnel offloading code by creating udp_tunnel_nic
infrastructure, from Jakub Kicinski.
26) Several pci_ --> dma_ API conversions, from Christophe JAILLET.
27) Add FLOW_ACTION_POLICE support to mlxsw, from Ido Schimmel.
28) Add SK_LOOKUP bpf program type, from Jakub Sitnicki.
29) Refactor a lot of networking socket option handling code in order to
avoid set_fs() calls, from Christoph Hellwig.
30) Add rfc4884 support to icmp code, from Willem de Bruijn.
31) Support TBF offload in dpaa2-eth driver, from Ioana Ciornei.
32) Support XDP_REDIRECT in qede driver, from Alexander Lobakin.
33) Support PCI relaxed ordering in mlx5 driver, from Aya Levin.
34) Support TCP syncookies in MPTCP, from Flowian Westphal.
35) Fix several tricky cases of PMTU handling wrt. briding, from Stefano
Brivio.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2056 commits)
net: thunderx: initialize VF's mailbox mutex before first usage
usb: hso: remove bogus check for EINPROGRESS
usb: hso: no complaint about kmalloc failure
hso: fix bailout in error case of probe
ip_tunnel_core: Fix build for archs without _HAVE_ARCH_IPV6_CSUM
selftests/net: relax cpu affinity requirement in msg_zerocopy test
mptcp: be careful on subflow creation
selftests: rtnetlink: make kci_test_encap() return sub-test result
selftests: rtnetlink: correct the final return value for the test
net: dsa: sja1105: use detected device id instead of DT one on mismatch
tipc: set ub->ifindex for local ipv6 address
ipv6: add ipv6_dev_find()
net: openvswitch: silence suspicious RCU usage warning
Revert "vxlan: fix tos value before xmit"
ptp: only allow phase values lower than 1 period
farsync: switch from 'pci_' to 'dma_' API
wan: wanxl: switch from 'pci_' to 'dma_' API
hv_netvsc: do not use VF device if link is down
dpaa2-eth: Fix passing zero to 'PTR_ERR' warning
net: macb: Properly handle phylink on at91sam9x
...
|
|
Pull documentation updates from Jonathan Corbet:
"It's been a busy cycle for documentation - hopefully the busiest for a
while to come. Changes include:
- Some new Chinese translations
- Progress on the battle against double words words and non-HTTPS
URLs
- Some block-mq documentation
- More RST conversions from Mauro. At this point, that task is
essentially complete, so we shouldn't see this kind of churn again
for a while. Unless we decide to switch to asciidoc or
something...:)
- Lots of typo fixes, warning fixes, and more"
* tag 'docs-5.9' of git://git.lwn.net/linux: (195 commits)
scripts/kernel-doc: optionally treat warnings as errors
docs: ia64: correct typo
mailmap: add entry for <alobakin@marvell.com>
doc/zh_CN: add cpu-load Chinese version
Documentation/admin-guide: tainted-kernels: fix spelling mistake
MAINTAINERS: adjust kprobes.rst entry to new location
devices.txt: document rfkill allocation
PCI: correct flag name
docs: filesystems: vfs: correct flag name
docs: filesystems: vfs: correct sync_mode flag names
docs: path-lookup: markup fixes for emphasis
docs: path-lookup: more markup fixes
docs: path-lookup: fix HTML entity mojibake
CREDITS: Replace HTTP links with HTTPS ones
docs: process: Add an example for creating a fixes tag
doc/zh_CN: add Chinese translation prefer section
doc/zh_CN: add clearing-warn-once Chinese version
doc/zh_CN: add admin-guide index
doc:it_IT: process: coding-style.rst: Correct __maybe_unused compiler label
futex: MAINTAINERS: Re-add selftests directory
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull seccomp updates from Kees Cook:
"There are a bunch of clean ups and selftest improvements along with
two major updates to the SECCOMP_RET_USER_NOTIF filter return:
EPOLLHUP support to more easily detect the death of a monitored
process, and being able to inject fds when intercepting syscalls that
expect an fd-opening side-effect (needed by both container folks and
Chrome). The latter continued the refactoring of __scm_install_fd()
started by Christoph, and in the process found and fixed a handful of
bugs in various callers.
- Improved selftest coverage, timeouts, and reporting
- Add EPOLLHUP support for SECCOMP_RET_USER_NOTIF (Christian Brauner)
- Refactor __scm_install_fd() into __receive_fd() and fix buggy
callers
- Introduce 'addfd' command for SECCOMP_RET_USER_NOTIF (Sargun
Dhillon)"
* tag 'seccomp-v5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux: (30 commits)
selftests/seccomp: Test SECCOMP_IOCTL_NOTIF_ADDFD
seccomp: Introduce addfd ioctl to seccomp user notifier
fs: Expand __receive_fd() to accept existing fd
pidfd: Replace open-coded receive_fd()
fs: Add receive_fd() wrapper for __receive_fd()
fs: Move __scm_install_fd() to __receive_fd()
net/scm: Regularize compat handling of scm_detach_fds()
pidfd: Add missing sock updates for pidfd_getfd()
net/compat: Add missing sock updates for SCM_RIGHTS
selftests/seccomp: Check ENOSYS under tracing
selftests/seccomp: Refactor to use fixture variants
selftests/harness: Clean up kern-doc for fixtures
seccomp: Use -1 marker for end of mode 1 syscall list
seccomp: Fix ioctl number for SECCOMP_IOCTL_NOTIF_ID_VALID
selftests/seccomp: Rename user_trap_syscall() to user_notif_syscall()
selftests/seccomp: Make kcmp() less required
seccomp: Use pr_fmt
selftests/seccomp: Improve calibration loop
selftests/seccomp: use 90s as timeout
selftests/seccomp: Expand benchmark to per-filter measurements
...
|
|
Daniel Borkmann says:
====================
pull-request: bpf-next 2020-08-04
The following pull-request contains BPF updates for your *net-next* tree.
We've added 73 non-merge commits during the last 9 day(s) which contain
a total of 135 files changed, 4603 insertions(+), 1013 deletions(-).
The main changes are:
1) Implement bpf_link support for XDP. Also add LINK_DETACH operation for the BPF
syscall allowing processes with BPF link FD to force-detach, from Andrii Nakryiko.
2) Add BPF iterator for map elements and to iterate all BPF programs for efficient
in-kernel inspection, from Yonghong Song and Alexei Starovoitov.
3) Separate bpf_get_{stack,stackid}() helpers for perf events in BPF to avoid
unwinder errors, from Song Liu.
4) Allow cgroup local storage map to be shared between programs on the same
cgroup. Also extend BPF selftests with coverage, from YiFei Zhu.
5) Add BPF exception tables to ARM64 JIT in order to be able to JIT BPF_PROBE_MEM
load instructions, from Jean-Philippe Brucker.
6) Follow-up fixes on BPF socket lookup in combination with reuseport group
handling. Also add related BPF selftests, from Jakub Sitnicki.
7) Allow to use socket storage in BPF_PROG_TYPE_CGROUP_SOCK-typed programs for
socket create/release as well as bind functions, from Stanislav Fomichev.
8) Fix an info leak in xsk_getsockopt() when retrieving XDP stats via old struct
xdp_statistics, from Peilin Ye.
9) Fix PT_REGS_RC{,_CORE}() macros in libbpf for MIPS arch, from Jerry Crunchtime.
10) Extend BPF kernel test infra with skb->family and skb->{local,remote}_ip{4,6}
fields and allow user space to specify skb->dev via ifindex, from Dmitry Yakunin.
11) Fix a bpftool segfault due to missing program type name and make it more robust
to prevent them in future gaps, from Quentin Monnet.
12) Consolidate cgroup helper functions across selftests and fix a v6 localhost
resolver issue, from John Fastabend.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A later patch will refuse to set the action of certain traps in mlxsw
and also to change the policer binding of certain groups. Pass extack so
that failure could be communicated clearly to user space.
Reviewed-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the packet trap that can report packets that were ECN marked due to RED
AQM.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
net/core/fib_rules.c:26:7: warning: "CONFIG_IP_MULTIPLE_TABLES" is not defined, evaluates to 0 [-Wundef]
#elif CONFIG_IP_MULTIPLE_TABLES
^~~~~~~~~~~~~~~~~~~~~~~~~
Fixes: 8b66a6fd34f5 ("fib: fix another fib_rules_ops indirect call wrapper problem")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-By: Brian Vazquez <brianvv@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When we don't care about vlan depth, we could pass NULL instead of the
address of a unused local variable to skb_network_protocol() as a param.
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In fact, skb_pagelen() - skb_headlen() is equal to __skb_pagelen(), use it
directly to avoid unnecessary skb_headlen() call.
Also fix the CHECK note of checkpatch.pl:
Comparison to NULL could be written "!__pskb_pull_tail"
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler updates from Ingo Molnar:
- Improve uclamp performance by using a static key for the fast path
- Add the "sched_util_clamp_min_rt_default" sysctl, to optimize for
better power efficiency of RT tasks on battery powered devices.
(The default is to maximize performance & reduce RT latencies.)
- Improve utime and stime tracking accuracy, which had a fixed boundary
of error, which created larger and larger relative errors as the
values become larger. This is now replaced with more precise
arithmetics, using the new mul_u64_u64_div_u64() helper in math64.h.
- Improve the deadline scheduler, such as making it capacity aware
- Improve frequency-invariant scheduling
- Misc cleanups in energy/power aware scheduling
- Add sched_update_nr_running tracepoint to track changes to nr_running
- Documentation additions and updates
- Misc cleanups and smaller fixes
* tag 'sched-core-2020-08-03' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (54 commits)
sched/doc: Factorize bits between sched-energy.rst & sched-capacity.rst
sched/doc: Document capacity aware scheduling
sched: Document arch_scale_*_capacity()
arm, arm64: Fix selection of CONFIG_SCHED_THERMAL_PRESSURE
Documentation/sysctl: Document uclamp sysctl knobs
sched/uclamp: Add a new sysctl to control RT default boost value
sched/uclamp: Fix a deadlock when enabling uclamp static key
sched: Remove duplicated tick_nohz_full_enabled() check
sched: Fix a typo in a comment
sched/uclamp: Remove unnecessary mutex_init()
arm, arm64: Select CONFIG_SCHED_THERMAL_PRESSURE
sched: Cleanup SCHED_THERMAL_PRESSURE kconfig entry
arch_topology, sched/core: Cleanup thermal pressure definition
trace/events/sched.h: fix duplicated word
linux/sched/mm.h: drop duplicated words in comments
smp: Fix a potential usage of stale nr_cpus
sched/fair: update_pick_idlest() Select group with lowest group_util when idle_cpus are equal
sched: nohz: stop passing around unused "ticks" parameter.
sched: Better document ttwu()
sched: Add a tracepoint to track rq->nr_running
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull RCU updates from Ingo Molnar:
- kfree_rcu updates
- RCU tasks updates
- Read-side scalability tests
- SRCU updates
- Torture-test updates
- Documentation updates
- Miscellaneous fixes
* tag 'core-rcu-2020-08-03' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (109 commits)
torture: Remove obsolete "cd $KVM"
torture: Avoid duplicate specification of qemu command
torture: Dump ftrace at shutdown only if requested
torture: Add kvm-tranform.sh script for qemu-cmd files
torture: Add more tracing crib notes to kvm.sh
torture: Improve diagnostic for KCSAN-incapable compilers
torture: Correctly summarize build-only runs
torture: Pass --kmake-arg to all make invocations
rcutorture: Check for unwatched readers
torture: Abstract out console-log error detection
torture: Add a stop-run capability
torture: Create qemu-cmd in --buildonly runs
rcu/rcutorture: Replace 0 with false
torture: Add --allcpus argument to the kvm.sh script
torture: Remove whitespace from identify_qemu_vcpus output
rcutorture: NULL rcu_torture_current earlier in cleanup code
rcutorture: Handle non-statistic bang-string error messages
torture: Set configfile variable to current scenario
rcutorture: Add races with task-exit processing
locktorture: Use true and false to assign to bool variables
...
|
|
Resolved kernel/bpf/btf.c using instructions from merge commit
69138b34a7248d2396ab85c8652e20c0c39beaba
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add LINK_DETACH command to force-detach bpf_link without destroying it. It has
the same behavior as auto-detaching of bpf_link due to cgroup dying for
bpf_cgroup_link or net_device being destroyed for bpf_xdp_link. In such case,
bpf_link is still a valid kernel object, but is defuncts and doesn't hold BPF
program attached to corresponding BPF hook. This functionality allows users
with enough access rights to manually force-detach attached bpf_link without
killing respective owner process.
This patch implements LINK_DETACH for cgroup, xdp, and netns links, mostly
re-using existing link release handling code.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Song Liu <songliubraving@fb.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/20200731182830.286260-2-andriin@fb.com
|
|
It turns out that on commit 41d707b7332f ("fib: fix fib_rules_ops
indirect calls wrappers") I forgot to include the case when
CONFIG_IP_MULTIPLE_TABLES is not set.
Fixes: 41d707b7332f ("fib: fix fib_rules_ops indirect calls wrappers")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Brian Vazquez <brianvv@google.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
netdev protodown is a mechanism that allows protocols to
hold an interface down. It was initially introduced in
the kernel to hold links down by a multihoming protocol.
There was also an attempt to introduce protodown
reason at the time but was rejected. protodown and protodown reason
is supported by almost every switching and routing platform.
It was ok for a while to live without a protodown reason.
But, its become more critical now given more than
one protocol may need to keep a link down on a system
at the same time. eg: vrrp peer node, port security,
multihoming protocol. Its common for Network operators and
protocol developers to look for such a reason on a networking
box (Its also known as errDisable by most networking operators)
This patch adds support for link protodown reason
attribute. There are two ways to maintain protodown
reasons.
(a) enumerate every possible reason code in kernel
- A protocol developer has to make a request and
have that appear in a certain kernel version
(b) provide the bits in the kernel, and allow user-space
(sysadmin or NOS distributions) to manage the bit-to-reasonname
map.
- This makes extending reason codes easier (kind of like
the iproute2 table to vrf-name map /etc/iproute2/rt_tables.d/)
This patch takes approach (b).
a few things about the patch:
- It treats the protodown reason bits as counter to indicate
active protodown users
- Since protodown attribute is already an exposed UAPI,
the reason is not enforced on a protodown set. Its a no-op
if not used.
the patch follows the below algorithm:
- presence of reason bits set indicates protodown
is in use
- user can set protodown and protodown reason in a
single or multiple setlink operations
- setlink operation to clear protodown, will return -EBUSY
if there are active protodown reason bits
- reason is not included in link dumps if not used
example with patched iproute2:
$cat /etc/iproute2/protodown_reasons.d/r.conf
0 mlag
1 evpn
2 vrrp
3 psecurity
$ip link set dev vxlan0 protodown on protodown_reason vrrp on
$ip link set dev vxlan0 protodown_reason mlag on
$ip link show
14: vxlan0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
DEFAULT group default qlen 1000
link/ether f6:06:be:17:91:e7 brd ff:ff:ff:ff:ff:ff protodown on <mlag,vrrp>
$ip link set dev vxlan0 protodown_reason mlag off
$ip link set dev vxlan0 protodown off protodown_reason vrrp off
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This change adds TCP_NLA_EDT to SCM_TIMESTAMPING_OPT_STATS that reports
the earliest departure time(EDT) of the timestamped skb. By tracking EDT
values of the skb from different timestamps, we can observe when and how
much the value changed. This allows to measure the precise delay
injected on the sender host e.g. by a bpf-base throttler.
Signed-off-by: Yousuk Seung <ysseung@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Soheil Hassas Yeganeh <soheil@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When we don't care about vlan depth, we could pass NULL instead of the
address of a unused local variable to skb_network_protocol() as a param.
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Number of .dumpit functions try to ignore -EOPNOTSUPP errors.
Recent change missed that, and started reporting all errors
but -EMSGSIZE back from dumps. This leads to situation like
this:
$ devlink dev info
devlink answers: Operation not supported
Dump should not report an error just because the last device
to be queried could not provide an answer.
To fix this and avoid similar confusion make sure we clear
err properly, and not leave it set to an error if we don't
terminate the iteration.
Fixes: c62c2cfb801b ("net: devlink: don't ignore errors during dumpit")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This lets us use socket storage from the following hooks:
* BPF_CGROUP_INET_SOCK_CREATE
* BPF_CGROUP_INET_SOCK_RELEASE
* BPF_CGROUP_INET4_POST_BIND
* BPF_CGROUP_INET6_POST_BIND
Using existing 'bpf_sk_storage_get_proto' doesn't work because
second argument is ARG_PTR_TO_SOCKET. Even though
BPF_PROG_TYPE_CGROUP_SOCK hooks operate on 'struct bpf_sock',
the verifier still considers it as a PTR_TO_CTX.
That's why I'm adding another 'bpf_sk_storage_get_cg_sock_proto'
definition strictly for BPF_PROG_TYPE_CGROUP_SOCK which accepts
ARG_PTR_TO_CTX which is really 'struct sock' for this program type.
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Song Liu <songliubraving@fb.com>
Link: https://lore.kernel.org/bpf/20200729003104.1280813-1-sdf@google.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/paulmck/linux-rcu into core/rcu
Pull the v5.9 RCU bits from Paul E. McKenney:
- Documentation updates
- Miscellaneous fixes
- kfree_rcu updates
- RCU tasks updates
- Read-side scalability tests
- SRCU updates
- Torture-test updates
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
This patch fixes:
commit b9aaec8f0be5 ("fib: use indirect call wrappers in the most common
fib_rules_ops") which didn't consider the case when
CONFIG_IPV6_MULTIPLE_TABLES is not set.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Fixes: b9aaec8f0be5 ("fib: use indirect call wrappers in the most common fib_rules_ops")
Signed-off-by: Brian Vazquez <brianvv@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cited commit mistakenly removed the trap group for externally routed
packets (e.g., via the management interface) and grouped locally routed
and externally routed packet traps under the same group, thereby
subjecting them to the same policer.
This can result in problems, for example, when FRR is restarted and
suddenly all transient traffic is trapped to the CPU because of a
default route through the management interface. Locally routed packets
required to re-establish a BGP connection will never reach the CPU and
the routing tables will not be re-populated.
Fix this by using a different trap group for externally routed packets.
Fixes: 8110668ecd9a ("mlxsw: spectrum_trap: Register layer 3 control traps")
Reported-by: Alex Veber <alexve@mellanox.com>
Tested-by: Alex Veber <alexve@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This avoids another inderect call per RX packet which save us around
20-40 ns.
Changelog:
v1 -> v2:
- Move declaraions to fib_rules.h to remove warnings
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Brian Vazquez <brianvv@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that BPF program/link management is centralized in generic net_device
code, kernel code never queries program id from drivers, so
XDP_QUERY_PROG/XDP_QUERY_PROG_HW commands are unnecessary.
This patch removes all the implementations of those commands in kernel, along
the xdp_attachment_query().
This patch was compile-tested on allyesconfig.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200722064603.3350758-10-andriin@fb.com
|
|
Implement XDP link-specific show_fdinfo and link_info to emit ifindex.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200722064603.3350758-7-andriin@fb.com
|
|
Add support for LINK_UPDATE command for BPF XDP link to enable reliable
replacement of underlying BPF program.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200722064603.3350758-6-andriin@fb.com
|
|
Add bpf_link-based API (bpf_xdp_link) to attach BPF XDP program through
BPF_LINK_CREATE command.
bpf_xdp_link is mutually exclusive with direct BPF program attachment,
previous BPF program should be detached prior to attempting to create a new
bpf_xdp_link attachment (for a given XDP mode). Once BPF link is attached, it
can't be replaced by other BPF program attachment or link attachment. It will
be detached only when the last BPF link FD is closed.
bpf_xdp_link will be auto-detached when net_device is shutdown, similarly to
how other BPF links behave (cgroup, flow_dissector). At that point bpf_link
will become defunct, but won't be destroyed until last FD is closed.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200722064603.3350758-5-andriin@fb.com
|
|
Further refactor XDP attachment code. dev_change_xdp_fd() is split into two
parts: getting bpf_progs from FDs and attachment logic, working with
bpf_progs. This makes attachment logic a bit more straightforward and
prepares code for bpf_xdp_link inclusion, which will share the common logic.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200722064603.3350758-4-andriin@fb.com
|
|
Instead of delegating to drivers, maintain information about which BPF
programs are attached in which XDP modes (generic/skb, driver, or hardware)
locally in net_device. This effectively obsoletes XDP_QUERY_PROG command.
Such re-organization simplifies existing code already. But it also allows to
further add bpf_link-based XDP attachments without drivers having to know
about any of this at all, which seems like a good setup.
XDP_SETUP_PROG/XDP_SETUP_PROG_HW are just low-level commands to driver to
install/uninstall active BPF program. All the higher-level concerns about
prog/link interaction will be contained within generic driver-agnostic logic.
All the XDP_QUERY_PROG calls to driver in dev_xdp_uninstall() were removed.
It's not clear for me why dev_xdp_uninstall() were passing previous prog_flags
when resetting installed programs. That seems unnecessary, plus most drivers
don't populate prog_flags anyways. Having XDP_SETUP_PROG vs XDP_SETUP_PROG_HW
should be enough of an indicator of what is required of driver to correctly
reset active BPF program. dev_xdp_uninstall() is also generalized as an
iteration over all three supported mode.
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200722064603.3350758-3-andriin@fb.com
|
