| Age | Commit message (Collapse) | Author |
|---|
|
Reported-by: checkpatch
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
|
|
Since other network components (and some drivers) uses the control block
provided in skb's, the network coding feature might wrongly assume that
an SKB has been decoded, and thus not try to code it with another packet
again. This happens for instance when batman-adv is running on a bridge device.
Fix this by clearing the control block for every received SKB.
Introduced by 3c12de9a5c756b23fe7c9ab332474ece1568914c
("batman-adv: network coding - code and transmit packets if possible")
Signed-off-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
|
|
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
|
|
Signed-off-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
|
|
With this patch a node sends IPv4 multicast packets to nodes which
have a BATADV_MCAST_WANT_ALL_IPV4 flag set and IPv6 multicast packets
to nodes which have a BATADV_MCAST_WANT_ALL_IPV6 flag set, too.
Why is this needed? There are scenarios involving bridges where
multicast report snooping and multicast TT announcements are not
sufficient, which would lead to packet loss for some nodes otherwise:
MLDv1 and IGMPv1/IGMPv2 have a suppression mechanism
for multicast listener reports. When we have an MLDv1/IGMPv1/IGMPv2
querier behind a bridge then our snooping bridge is potentially not
going to see any reports even though listeners exist because according
to RFC4541 such reports are only forwarded to multicast routers:
-----------------------------------------------------------
---------------
{Querier}---|Snoop. Switch|----{Listener}
---------------
\ ^
-------
| br0 | < ???
-------
\
_-~---~_
_-~/ ~-_
~ batman-adv \-----{Sender}
\~_ cloud ~/
-~~__-__-~_/
I) MLDv1 Query: {Querier} -> flooded
II) MLDv1 Report: {Listener} -> {Querier}
-> br0 cannot detect the {Listener}
=> Packets from {Sender} need to be forwarded to all
detected listeners and MLDv1/IGMPv1/IGMPv2 queriers.
-----------------------------------------------------------
Note that we do not need to explicitly forward to MLDv2/IGMPv3 queriers,
because these protocols have no report suppression: A bridge has no
trouble detecting MLDv2/IGMPv3 listeners.
Even though we do not support bridges yet we need to provide the
according infrastructure already to not break compatibility later.
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
|
|
With this patch a node may additionally perform the dropping or
unicasting behaviour for a link-local IPv4 and link-local-all-nodes
IPv6 multicast packet, too.
The extra counter and BATADV_MCAST_WANT_ALL_UNSNOOPABLES flag is needed
because with a future bridge snooping support integration a node with a
bridge on top of its soft interface is not able to reliably detect its
multicast listeners for IPv4 link-local and the IPv6
link-local-all-nodes addresses anymore (see RFC4541, section 2.1.2.2
and section 3).
Even though this new flag does make "no difference" now, it'll ensure
a seamless integration of multicast bridge support without needing to
break compatibility later.
Also note, that even with multicast bridge support it won't be possible
to optimize 224.0.0.x and ff02::1 towards nodes with bridges, they will
always receive these ranges.
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
|
|
If the soft interface of a node is not part of a bridge then a node
announces a new multicast TVLV: The existence of this TVLV
signalizes that this node is announcing all of its multicast listeners
via the translation table infrastructure.
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
|
|
With this patch a node which has no bridge interface on top of its soft
interface announces its local multicast listeners via the translation
table.
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
|
|
On some architectures ether_addr_copy() is slightly faster
than memcpy() therefore use the former when possible.
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
|
|
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
net/ipv4/tcp_metrics.c
Overlapping changes between the "don't create two tcp metrics objects
with the same key" race fix in net and the addition of the destination
address in the lookup key in net-next.
Minor overlapping changes in bnx2x driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Batman-adv prepends a full ethernet header in addition to its own
header. This has to be reflected in the MTU calculation, especially
since the value is used to set dev->hard_header_len.
Introduced by 411d6ed93a5d0601980d3e5ce75de07c98e3a7de
("batman-adv: consider network coding overhead when calculating required mtu")
Reported-by: cmsv <cmsv@wirelesspt.net>
Reported-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
|
|
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
|
|
With unrolling the batadv_header into the respective structures, the
offsetof checks are now useless. Instead, add build checks for all
packet types which go over the wire to avoid problems with wrong sizes
or compatibility issues on some architectures which don't use every day.
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
|
|
The AP isolation status may be evaluated in different spots.
Create an helper function to avoid code duplication.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
|
|
As suggested by checkpatch, remove all the references to the
FSF address since the kernel already has one reference in
its documentation.
In this way it is easier to update it in case of future
changes.
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
|
|
struct batadv_icmp_header currently has a size of 17, which
will be padded to 20 on some architectures. Fix this by
unrolling the header into the parent structures.
Moreover keep the ICMP parsing functions as generic as they
are now by using a stub icmp_header struct during packet
parsing.
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
|
|
The size of the batadv_header of 3 is problematic on some architectures
which automatically pad all structures to a 32 bit boundary. To not lose
performance by packing this struct, better embed it into the various
host structures.
Reported-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
|
|
Each routing protocol has its own metric semantic and
therefore is the protocol itself the only component able to
compare two metrics to check their "similarity".
This new API allows each routing protocol to implement its
own logic and make the external code protocol agnostic.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
|
|
This new API allows to compare the two neighbours based on
the metric avoiding the user to deal with any routing
algorithm specific detail
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
|
|
A TT response may be prepared and sent while the local or
global translation table is getting updated.
The worst case is when one of the tables is accessed after
its content has been recently updated but the metadata
(TTVN/CRC) has not yet. In this case the reader will get a
table content which does not match the TTVN/CRC.
This will lead to an inconsistent state and so to a TT
recovery.
To avoid entering this situation, put a lock around those TT
operations recomputing the metadata and around the TT
Response creation (the latter is the only reader that
accesses the metadata together with the table).
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
|
|
Since batman-adv is now fully VLAN-aware, a proper framework
able to handle per-vlan-interface attributes is needed.
Those attributes will affect the associated VLAN interface
only, rather than the real soft_iface (which would result
in every vlan interface having the same attribute
configuration).
To make the code simpler and easier to extend, attributes
associated to the standalone soft_iface are now treated
like belonging to yet another vlan having a special vid.
This vid is different from the others because it is made up
by all zeros and the VLAN_HAS_TAG bit is not set.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
|
|
To make the translation table code VLAN-aware, each entry
must carry the VLAN ID which it belongs to. This patch adds
such attribute to the related TT structures.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
|
|
The module prints a warning when the MTU on the hard interface is too
small to transfer payload traffic without fragmentation. The required
MTU is calculated based on the encapsulation header size. If network
coding is compild into the module its header size is taken into
account as well.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
|
|
the icmp and the icmp_rr packets share the same initial
fields since they use the same code to be processed and
forwarded.
Extract the common fields and put them into a separate
struct so that future ICMP packets can be easily added
without bloating the packet definition.
However, keep the seqno field outside of the newly created
common header because future ICMP types may require a
bigger sequence number space.
This change breaks compatibility due to fields reordering
in the ICMP headers.
Signed-off-by: Antonio Quartulli <antonio@open-mesh.com>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
|
|
Fragments arriving at their destination are buffered for later merge.
Merged packets are passed to the main receive function as had they never
been fragmented.
Fragments are forwarded without merging if the MTU of the outgoing
interface is smaller than the size of the merged packet.
Signed-off-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
|
|
Remove the existing fragmentation code before adding the new version
and delete unicast.{h,c}.
batadv_unicast_send_skb() is moved to send.c and renamed to
batadv_send_skb_unicast().
fragmentation entry in sysfs (bat_priv->fragmentation) is kept for use in
the new fragmentation code.
BATADV_UNICAST_FRAG packet type is renamed to BATADV_FRAG for use in the
new fragmentation code.
Signed-off-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
|
|
Reordering the packet type numbers allows us to handle unicast
packets in a general way - even if we don't know the specific packet
type, we can still forward it. There was already code handling
this for a couple of unicast packets, and this is the more
generalized version to do that.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
|
|
Since we removed the __packed from most of the packets, we should
make sure that the offset generated by the compiler are correct for
sent/received data.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
|
|
This is replaced by a userspace program, we don't need this
functionality to bloat the kernel.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
|
|
Instead of generating roaming specific packets the TVLV unicast API is
used to send roaming information.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
|
|
Instead of generating TT specific packets the TVLV unicast API is used
to send translation table data.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
|
|
Prior to this patch batman-adv read the advertised uplink bandwidth
from userspace and compressed this information into a single byte
called "gateway class".
Now the download & upload bandwidth information is sent as-is. No
userspace change is necessary since the sysfs API always allowed
to specify a bandwidth.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Spyros Gasteratos <morfeas3000@gmail.com>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
|
|
The goal is to provide the infrastructure for sending, receiving and
parsing information 'containers' while preserving backward
compatibility. TVLV (based on the commonly known Type Length Value
technique) was chosen as the format for those containers. Even if a
node does not know the tvlv type of a certain container it can simply
skip the current container and proceed with the next. Past experience
has shown features evolve over time, so a 'version' field was added
right from the start to allow differentiating between feature
variants - hence the name: T(ype) V(ersion) L(ength) V(alue).
This patch introduces the basic TVLV infrastructure:
* register / unregister tvlv containers to be sent with each OGM
(on primary interfaces only)
* register / unregister callback handlers to be called upon
finding the corresponding tvlv type in a tvlv buffer
* unicast tvlv send / receive API calls
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Spyros Gasteratos <morfeas3000@gmail.com>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
|
|
batman-adv saves its table of packet handlers as a global state, so handlers
must be set up only once (and setting them up a second time will fail).
The recently-added network coding support tries to set up its handler each time
a new softif is registered, which obviously fails when more that one softif is
used (and in consequence, the softif creation fails).
Fix this by splitting up batadv_nc_init into batadv_nc_init (which is called
only once) and batadv_nc_mesh_init (which is called for each softif); in
addition batadv_nc_free is renamed to batadv_nc_mesh_free to keep naming
consistent.
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch>
Signed-off-by: Antonio Quartulli <antonio@meshcoding.com>
|
|
The skb priority field may help the wireless driver to choose the right
queue (e.g. WMM queues). This should be set in batman-adv, as this
information is only available here.
This patch adds support for IPv4/IPv6 DS fields and VLAN PCP. Note that
only VLAN PCP is used if a VLAN header is present. Also initially set
TC_PRIO_CONTROL only for self-generated packets, and keep the priority
set by higher layers.
Signed-off-by: Simon Wunderlich <simon@open-mesh.com>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
|
|
Callers of skb_seq_read() are currently forced to call skb_abort_seq_read()
even when consuming all the data because the last call to skb_seq_read (the
one that returns 0 to indicate the end) fails to unmap the last fragment page.
With this patch callers will be allowed to traverse the SKB data by calling
skb_prepare_seq_read() once and repeatedly calling skb_seq_read() as originally
intended (and documented in the original commit 677e90eda), that is, only call
skb_abort_seq_read() if the sequential read is actually aborted.
Signed-off-by: Wedson Almeida Filho <wedsonaf@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On errors in batadv_mesh_init(), bat_counters will be freed in both
batadv_mesh_free() and batadv_softif_init_late(). This patch fixes this
by returning earlier from batadv_softif_init_late() in case of errors in
batadv_mesh_init() and by setting bat_counters to NULL after freeing.
Signed-off-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
|
|
nc_worker accesses the originator table during its periodic
work, but since the originator table is freed before
stopping the worker this leads to a global protection fault.
Fix this by killing the worker (in nc_free) before freeing
the originator table.
Moreover tidy up the entire clean up routine by running all
the subcomponents freeing procedures first and then killing
the TT and the originator tables at the end.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
|
|
batadv_param_set_ra() strips the trailing '\n' from the supplied
string buffer without checking the length of the buffer first. This
patches avoids random memory access and associated potential
crashes.
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
|
|
Conflicts:
drivers/net/ethernet/emulex/benet/be_main.c
drivers/net/ethernet/intel/igb/igb_main.c
drivers/net/wireless/brcm80211/brcmsmac/mac80211_if.c
include/net/scm.h
net/batman-adv/routing.c
net/ipv4/tcp_input.c
The e{uid,gid} --> {uid,gid} credentials fix conflicted with the
cleanup in net-next to now pass cred structs around.
The be2net driver had a bug fix in 'net' that overlapped with the VLAN
interface changes by Patrick McHardy in net-next.
An IGB conflict existed because in 'net' the build_skb() support was
reverted, and in 'net-next' there was a comment style fix within that
code.
Several batman-adv conflicts were resolved by making sure that all
calls to batadv_is_my_mac() are changed to have a new bat_priv first
argument.
Eric Dumazet's TS ECR fix in TCP in 'net' conflicted with the F-RTO
rewrite in 'net-next', mostly overlapping changes.
Thanks to Stephen Rothwell and Antonio Quartulli for help with several
of these merge resolutions.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On a multi-mesh node (a node running more than one batman-adv
virtual interface) batadv_is_my_mac() has to check MAC
addresses of hard interfaces belonging to the current mesh
only.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
|
|
As reported by checkpatch, seq_puts has to be preferred with
respect to seq_printf when the format is a constant string
(no va_args)
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
|
|
The sysfs configuration interface of batman-adv to add/remove soft-interfaces
is not deadlock free and doesn't follow the currently common way to create new
virtual interfaces.
An additional interface though rtnl_link is introduced which provides easy device
creation/deletion with tools like "ip":
$ ip link add dev bat0 type batadv
$ ip link del dev bat0
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
|
|
Network coding exploits the 802.11 shared medium to allow multiple
packets to be sent in a single transmission. In brief, a relay can XOR
two packets, and send the coded packet to two destinations. The
receivers can decode one of the original packets by XOR'ing the coded
packet with the other original packet. This will lead to increased
throughput in topologies where two packets cross one relay.
In a simple topology with three nodes, it takes four transmissions
without network coding to get one packet from Node A to Node B and one
from Node B to Node A:
1. Node A ---- p1 ---> Node R Node B
2. Node A Node R <--- p2 ---- Node B
3. Node A <--- p2 ---- Node R Node B
4. Node A Node R ---- p1 ---> Node B
With network coding, the relay only needs one transmission, which saves
us one slot of valuable airtime:
1. Node A ---- p1 ---> Node R Node B
2. Node A Node R <--- p2 ---- Node B
3. Node A <- p1 x p2 - Node R - p1 x p2 -> Node B
The same principle holds for a topology including five nodes. Here the
packets from Node A and Node B are overheard by Node C and Node D,
respectively. This allows Node R to send a network coded packet to save
one transmission:
Node A Node B
| \ / |
| p1 p2 |
| \ / |
p1 > Node R < p2
| |
| / \ |
| p1 x p2 p1 x p2 |
v / \ v
/ \
Node C < > Node D
More information is available on the open-mesh.org wiki[1].
This patch adds the initial code to support network coding in
batman-adv. It sets up a worker thread to do house keeping and adds a
sysfs file to enable/disable network coding. The feature is disabled by
default, as it requires a wifi-driver with working promiscuous mode, and
also because it adds a small delay at each hop.
[1] http://www.open-mesh.org/projects/batman-adv/wiki/Catwoman
Signed-off-by: Martin Hundebøll <martin@hundeboll.net>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
|
|
I'm not sure why, but the hlist for each entry iterators were conceived
list_for_each_entry(pos, head, member)
The hlist ones were greedy and wanted an extra parameter:
hlist_for_each_entry(tpos, pos, head, member)
Why did they need an extra pos parameter? I'm not quite sure. Not only
they don't really need it, it also prevents the iterator from looking
exactly like the list iterator, which is unfortunate.
Besides the semantic patch, there was some manual work required:
- Fix up the actual hlist iterators in linux/list.h
- Fix up the declaration of other iterators based on the hlist ones.
- A very small amount of places were using the 'node' parameter, this
was modified to use 'obj->member' instead.
- Coccinelle didn't handle the hlist_for_each_entry_safe iterator
properly, so those had to be fixed up manually.
The semantic patch which is mostly the work of Peter Senna Tschudin is here:
@@
iterator name hlist_for_each_entry, hlist_for_each_entry_continue, hlist_for_each_entry_from, hlist_for_each_entry_rcu, hlist_for_each_entry_rcu_bh, hlist_for_each_entry_continue_rcu_bh, for_each_busy_worker, ax25_uid_for_each, ax25_for_each, inet_bind_bucket_for_each, sctp_for_each_hentry, sk_for_each, sk_for_each_rcu, sk_for_each_from, sk_for_each_safe, sk_for_each_bound, hlist_for_each_entry_safe, hlist_for_each_entry_continue_rcu, nr_neigh_for_each, nr_neigh_for_each_safe, nr_node_for_each, nr_node_for_each_safe, for_each_gfn_indirect_valid_sp, for_each_gfn_sp, for_each_host;
type T;
expression a,c,d,e;
identifier b;
statement S;
@@
-T b;
<+... when != b
(
hlist_for_each_entry(a,
- b,
c, d) S
|
hlist_for_each_entry_continue(a,
- b,
c) S
|
hlist_for_each_entry_from(a,
- b,
c) S
|
hlist_for_each_entry_rcu(a,
- b,
c, d) S
|
hlist_for_each_entry_rcu_bh(a,
- b,
c, d) S
|
hlist_for_each_entry_continue_rcu_bh(a,
- b,
c) S
|
for_each_busy_worker(a, c,
- b,
d) S
|
ax25_uid_for_each(a,
- b,
c) S
|
ax25_for_each(a,
- b,
c) S
|
inet_bind_bucket_for_each(a,
- b,
c) S
|
sctp_for_each_hentry(a,
- b,
c) S
|
sk_for_each(a,
- b,
c) S
|
sk_for_each_rcu(a,
- b,
c) S
|
sk_for_each_from
-(a, b)
+(a)
S
+ sk_for_each_from(a) S
|
sk_for_each_safe(a,
- b,
c, d) S
|
sk_for_each_bound(a,
- b,
c) S
|
hlist_for_each_entry_safe(a,
- b,
c, d, e) S
|
hlist_for_each_entry_continue_rcu(a,
- b,
c) S
|
nr_neigh_for_each(a,
- b,
c) S
|
nr_neigh_for_each_safe(a,
- b,
c, d) S
|
nr_node_for_each(a,
- b,
c) S
|
nr_node_for_each_safe(a,
- b,
c, d) S
|
- for_each_gfn_sp(a, c, d, b) S
+ for_each_gfn_sp(a, c, d) S
|
- for_each_gfn_indirect_valid_sp(a, c, d, b) S
+ for_each_gfn_indirect_valid_sp(a, c, d) S
|
for_each_host(a,
- b,
c) S
|
for_each_host_safe(a,
- b,
c, d) S
|
for_each_mesh_entry(a,
- b,
c, d) S
)
...+>
[akpm@linux-foundation.org: drop bogus change from net/ipv4/raw.c]
[akpm@linux-foundation.org: drop bogus hunk from net/ipv6/raw.c]
[akpm@linux-foundation.org: checkpatch fixes]
[akpm@linux-foundation.org: fix warnings]
[akpm@linux-foudnation.org: redo intrusive kvm changes]
Tested-by: Peter Senna Tschudin <peter.senna@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
|
|
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
|
|
Since batman-adv cannot inter-operate with the host ARP table, this patch
introduces a batman-adv private storage for ARP entries exchanged within DAT.
This storage will represent the node local cache in the DAT protocol.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
|
|
The current unicast packet type does not contain the orig source address. This
patches add a new unicast packet (called UNICAST_4ADDR) which provides two new
fields: the originator source address and the subtype (the type of the data
contained in the packet payload). The former is useful to identify the node
which injected the packet into the network and the latter is useful to avoid
creating new unicast packet types in the future: a macro defining a new subtype
will be enough.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
|
|
New operations should not be started when they need an increased module
reference counter and try_module_get failed.
This patch addresses Coverity #712284: Unchecked return value
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
|
