| Age | Commit message (Collapse) | Author |
|---|
|
Spelling fixes in mm/.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
|
|
Nobody uses flush_tlb_pgtables anymore, this patch removes all remaining
traces of it from all archs.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Current ia64 kernel flushes icache by lazy_mmu_prot_update() *after*
set_pte(). This is too late. This patch removes lazy_mmu_prot_update and
add modfied set_pte() for flushing if necessary.
This patch flush icache of a page when
new pte has exec bit.
&& new pte has present bit
&& new pte is user's page.
&& (old *ptep is not present
|| new pte's pfn is not same to old *ptep's ptn)
&& new pte's page has no Pg_arch_1 bit.
Pg_arch_1 is set when a page is cache consistent.
I think this condition checks are much easier to understand than considering
"Where sync_icache_dcache() should be inserted ?".
pte_user() for ia64 was removed by http://lkml.org/lkml/2007/6/12/67 as
clean-up. So, I added it again.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Christoph Lameter <clameter@sgi.com>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The calculation of pgoff in do_linear_fault() should use PAGE_SHIFT and not
PAGE_CACHE_SHIFT since vma->vm_pgoff is in units of PAGE_SIZE and not
PAGE_CACHE_SIZE. At the moment linux/pagemap.h has PAGE_CACHE_SHIFT
defined as PAGE_SHIFT, but should that ever change this calculation would
break.
Signed-off-by: Dean Nelson <dcn@sgi.com>
Acked-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The commit b5810039a54e5babf428e9a1e89fc1940fabff11 contains the note
A last caveat: the ZERO_PAGE is now refcounted and managed with rmap
(and thus mapcounted and count towards shared rss). These writes to
the struct page could cause excessive cacheline bouncing on big
systems. There are a number of ways this could be addressed if it is
an issue.
And indeed this cacheline bouncing has shown up on large SGI systems.
There was a situation where an Altix system was essentially livelocked
tearing down ZERO_PAGE pagetables when an HPC app aborted during startup.
This situation can be avoided in userspace, but it does highlight the
potential scalability problem with refcounting ZERO_PAGE, and corner
cases where it can really hurt (we don't want the system to livelock!).
There are several broad ways to fix this problem:
1. add back some special casing to avoid refcounting ZERO_PAGE
2. per-node or per-cpu ZERO_PAGES
3. remove the ZERO_PAGE completely
I will argue for 3. The others should also fix the problem, but they
result in more complex code than does 3, with little or no real benefit
that I can see.
Why? Inserting a ZERO_PAGE for anonymous read faults appears to be a
false optimisation: if an application is performance critical, it would
not be doing many read faults of new memory, or at least it could be
expected to write to that memory soon afterwards. If cache or memory use
is critical, it should not be working with a significant number of
ZERO_PAGEs anyway (a more compact representation of zeroes should be
used).
As a sanity check -- mesuring on my desktop system, there are never many
mappings to the ZERO_PAGE (eg. 2 or 3), thus memory usage here should not
increase much without it.
When running a make -j4 kernel compile on my dual core system, there are
about 1,000 mappings to the ZERO_PAGE created per second, but about 1,000
ZERO_PAGE COW faults per second (less than 1 ZERO_PAGE mapping per second
is torn down without being COWed). So removing ZERO_PAGE will save 1,000
page faults per second when running kbuild, while keeping it only saves
less than 1 page clearing operation per second. 1 page clear is cheaper
than a thousand faults, presumably, so there isn't an obvious loss.
Neither the logical argument nor these basic tests give a guarantee of no
regressions. However, this is a reasonable opportunity to try to remove
the ZERO_PAGE from the pagefault path. If it is found to cause regressions,
we can reintroduce it and just avoid refcounting it.
The /dev/zero ZERO_PAGE usage and TLB tricks also get nuked. I don't see
much use to them except on benchmarks. All other users of ZERO_PAGE are
converted just to use ZERO_PAGE(0) for simplicity. We can look at
replacing them all and maybe ripping out ZERO_PAGE completely when we are
more satisfied with this solution.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus "snif" Torvalds <torvalds@linux-foundation.org>
|
|
All the current page_mkwrite() implementations also set the page dirty. Which
results in the set_page_dirty_balance() call to _not_ call balance, because the
page is already found dirty.
This allows us to dirty a _lot_ of pages without ever hitting
balance_dirty_pages(). Not good (tm).
Force a balance call if ->page_mkwrite() was successful.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Gurudas Pai reports kernel BUG at arch/i386/mm/highmem.c:15! below
sys_remap_file_pages, while running Oracle database test on x86 in 6GB
RAM: kunmap thinks we're in_interrupt because the preempt count has
wrapped.
That's because __do_fault expected to unmap page_table, but one of its
two callers do_nonlinear_fault already unmapped it: let do_linear_fault
unmap it first too, and then there's no need to pass the page_table arg
down.
Why have we been so slow to notice this? Probably through forgetting
that the mapping_cap_account_dirty test means that sys_remap_file_pages
nowadays only goes the full nonlinear vma route on a few memory-backed
filesystems like ramfs, tmpfs and hugetlbfs.
[ It also depends on CONFIG_HIGHPTE, so it becomes even harder to
trigger in practice. Many who have need of large memory have probably
migrated to x86-64..
Problem introduced by commit d0217ac04ca6591841e5665f518e38064f4e65bd
("mm: fault feedback #1") -- Linus ]
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: gurudas pai <gurudas.pai@oracle.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Now that arch/powerpc/platforms/cell/spufs/fault.c is always built in
the kernel there is no need to export handle_mm_fault anymore.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
lguest does some fairly lowlevel things to support a host, which
normal modules don't need:
math_state_restore:
When the guest triggers a Device Not Available fault, we need
to be able to restore the FPU
__put_task_struct:
We need to hold a reference to another task for inter-guest
I/O, and put_task_struct() is an inline function which calls
__put_task_struct.
access_process_vm:
We need to access another task for inter-guest I/O.
map_vm_area & __get_vm_area:
We need to map the switcher shim (ie. monitor) at 0xFFC01000.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix msync data loss and (less importantly) dirty page accounting
inaccuracies due to the race remaining in clear_page_dirty_for_io().
The deleted comment explains what the race was, and the added comments
explain how it is fixed.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Miklos Szeredi <miklos@szeredi.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch completes Linus's wish that the fault return codes be made into
bit flags, which I agree makes everything nicer. This requires requires
all handle_mm_fault callers to be modified (possibly the modifications
should go further and do things like fault accounting in handle_mm_fault --
however that would be for another patch).
[akpm@linux-foundation.org: fix alpha build]
[akpm@linux-foundation.org: fix s390 build]
[akpm@linux-foundation.org: fix sparc build]
[akpm@linux-foundation.org: fix sparc64 build]
[akpm@linux-foundation.org: fix ia64 build]
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ian Molton <spyro@f2s.com>
Cc: Bryan Wu <bryan.wu@analog.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Greg Ungerer <gerg@uclinux.org>
Cc: Matthew Wilcox <willy@debian.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Kazumoto Kojima <kkojima@rr.iij4u.or.jp>
Cc: Richard Curnow <rc@rc0.org.uk>
Cc: William Lee Irwin III <wli@holomorphy.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Miles Bader <uclinux-v850@lsi.nec.co.jp>
Cc: Chris Zankel <chris@zankel.net>
Acked-by: Kyle McMartin <kyle@mcmartin.ca>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
[ Still apparently needs some ARM and PPC loving - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Change ->fault prototype. We now return an int, which contains
VM_FAULT_xxx code in the low byte, and FAULT_RET_xxx code in the next byte.
FAULT_RET_ code tells the VM whether a page was found, whether it has been
locked, and potentially other things. This is not quite the way he wanted
it yet, but that's changed in the next patch (which requires changes to
arch code).
This means we no longer set VM_CAN_INVALIDATE in the vma in order to say
that a page is locked which requires filemap_nopage to go away (because we
can no longer remain backward compatible without that flag), but we were
going to do that anyway.
struct fault_data is renamed to struct vm_fault as Linus asked. address
is now a void __user * that we should firmly encourage drivers not to use
without really good reason.
The page is now returned via a page pointer in the vm_fault struct.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
__do_fault() was calling ->page_mkwrite() with the page lock held, which
violates the locking rules for that callback. Release and retake the page
lock around the callback to avoid deadlocking file systems which manually
take it.
Signed-off-by: Mark Fasheh <mark.fasheh@oracle.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Nonlinear mappings are (AFAIKS) simply a virtual memory concept that encodes
the virtual address -> file offset differently from linear mappings.
->populate is a layering violation because the filesystem/pagecache code
should need to know anything about the virtual memory mapping. The hitch here
is that the ->nopage handler didn't pass down enough information (ie. pgoff).
But it is more logical to pass pgoff rather than have the ->nopage function
calculate it itself anyway (because that's a similar layering violation).
Having the populate handler install the pte itself is likewise a nasty thing
to be doing.
This patch introduces a new fault handler that replaces ->nopage and
->populate and (later) ->nopfn. Most of the old mechanism is still in place
so there is a lot of duplication and nice cleanups that can be removed if
everyone switches over.
The rationale for doing this in the first place is that nonlinear mappings are
subject to the pagefault vs invalidate/truncate race too, and it seemed stupid
to duplicate the synchronisation logic rather than just consolidate the two.
After this patch, MAP_NONBLOCK no longer sets up ptes for pages present in
pagecache. Seems like a fringe functionality anyway.
NOPAGE_REFAULT is removed. This should be implemented with ->fault, and no
users have hit mainline yet.
[akpm@linux-foundation.org: cleanup]
[randy.dunlap@oracle.com: doc. fixes for readahead]
[akpm@linux-foundation.org: build fix]
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Mark Fasheh <mark.fasheh@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix the race between invalidate_inode_pages and do_no_page.
Andrea Arcangeli identified a subtle race between invalidation of pages from
pagecache with userspace mappings, and do_no_page.
The issue is that invalidation has to shoot down all mappings to the page,
before it can be discarded from the pagecache. Between shooting down ptes to
a particular page, and actually dropping the struct page from the pagecache,
do_no_page from any process might fault on that page and establish a new
mapping to the page just before it gets discarded from the pagecache.
The most common case where such invalidation is used is in file truncation.
This case was catered for by doing a sort of open-coded seqlock between the
file's i_size, and its truncate_count.
Truncation will decrease i_size, then increment truncate_count before
unmapping userspace pages; do_no_page will read truncate_count, then find the
page if it is within i_size, and then check truncate_count under the page
table lock and back out and retry if it had subsequently been changed (ptl
will serialise against unmapping, and ensure a potentially updated
truncate_count is actually visible).
Complexity and documentation issues aside, the locking protocol fails in the
case where we would like to invalidate pagecache inside i_size. do_no_page
can come in anytime and filemap_nopage is not aware of the invalidation in
progress (as it is when it is outside i_size). The end result is that
dangling (->mapping == NULL) pages that appear to be from a particular file
may be mapped into userspace with nonsense data. Valid mappings to the same
place will see a different page.
Andrea implemented two working fixes, one using a real seqlock, another using
a page->flags bit. He also proposed using the page lock in do_no_page, but
that was initially considered too heavyweight. However, it is not a global or
per-file lock, and the page cacheline is modified in do_no_page to increment
_count and _mapcount anyway, so a further modification should not be a large
performance hit. Scalability is not an issue.
This patch implements this latter approach. ->nopage implementations return
with the page locked if it is possible for their underlying file to be
invalidated (in that case, they must set a special vm_flags bit to indicate
so). do_no_page only unlocks the page after setting up the mapping
completely. invalidation is excluded because it holds the page lock during
invalidation of each page (and ensures that the page is not mapped while
holding the lock).
This also allows significant simplifications in do_no_page, because we have
the page locked in the right place in the pagecache from the start.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
be migrated
It is often known at allocation time whether a page may be migrated or not.
This patch adds a flag called __GFP_MOVABLE and a new mask called
GFP_HIGH_MOVABLE. Allocations using the __GFP_MOVABLE can be either migrated
using the page migration mechanism or reclaimed by syncing with backing
storage and discarding.
An API function very similar to alloc_zeroed_user_highpage() is added for
__GFP_MOVABLE allocations called alloc_zeroed_user_highpage_movable(). The
flags used by alloc_zeroed_user_highpage() are not changed because it would
change the semantics of an existing API. After this patch is applied there
are no in-kernel users of alloc_zeroed_user_highpage() so it probably should
be marked deprecated if this patch is merged.
Note that this patch includes a minor cleanup to the use of __GFP_ZERO in
shmem.c to keep all flag modifications to inode->mapping in the
shmem_dir_alloc() helper function. This clean-up suggestion is courtesy of
Hugh Dickens.
Additional credit goes to Christoph Lameter and Linus Torvalds for shaping the
concept. Credit to Hugh Dickens for catching issues with shmem swap vector
and ramfs allocations.
[akpm@linux-foundation.org: build fix]
[hugh@veritas.com: __GFP_ZERO cleanup]
Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Cc: Andy Whitcroft <apw@shadowen.org>
Cc: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This symbol got orphaned quite a while ago.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
get_user_pages() can try to allocate a nearly unlimited amount of memory on
behalf of a user process, even if that process has been OOM killed. The
OOM kill occurs upon return to user space via a SIGKILL, but
get_user_pages() will try allocate all its memory before returning. Change
get_user_pages() to check for TIF_MEMDIE, and if set then return
immediately.
Signed-off-by: Ethan Solomita <solo@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Replace a hand coded version of DIV_ROUND_UP().
Signed-off-by: Rolf Eike Beer <eike-kernel@sf-tec.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Some changes done a while ago to avoid pounding on ptep_set_access_flags and
update_mmu_cache in some race situations break sun4c which requires
update_mmu_cache() to always be called on minor faults.
This patch reworks ptep_set_access_flags() semantics, implementations and
callers so that it's now responsible for returning whether an update is
necessary or not (basically whether the PTE actually changed). This allow
fixing the sparc implementation to always return 1 on sun4c.
[akpm@linux-foundation.org: fixes, cleanups]
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: David Miller <davem@davemloft.net>
Cc: Mark Fortescue <mark@mtfhpc.demon.co.uk>
Acked-by: William Lee Irwin III <wli@holomorphy.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Re-introduce rmap verification patches that Hugh removed when he removed
PG_map_lock. PG_map_lock actually isn't needed to synchronise access to
anonymous pages, because PG_locked and PTL together already do.
These checks were important in discovering and fixing a rare rmap corruption
in SLES9.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Introduce a macro for suppressing gcc from generating a warning about a
probable uninitialized state of a variable.
Example:
- spinlock_t *ptl;
+ spinlock_t *uninitialized_var(ptl);
Not a happy solution, but those warnings are obnoxious.
- Using the usual pointlessly-set-it-to-zero approach wastes several
bytes of text.
- Using a macro means we can (hopefully) do something else if gcc changes
cause the `x = x' hack to stop working
- Using a macro means that people who are worried about hiding true bugs
can easily turn it off.
Signed-off-by: Borislav Petkov <bbpetkov@yahoo.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Minimum gcc version is 3.2 now. However, with likely profiling, even
modern gcc versions cannot always eliminate the call.
Replace the placeholder functions with the more conventional empty static
inlines, which should be optimal for everyone.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add a new mm function apply_to_page_range() which applies a given function to
every pte in a given virtual address range in a given mm structure. This is a
generic alternative to cut-and-pasting the Linux idiomatic pagetable walking
code in every place that a sequence of PTEs must be accessed.
Although this interface is intended to be useful in a wide range of
situations, it is currently used specifically by several Xen subsystems, for
example: to ensure that pagetables have been allocated for a virtual address
range, and to construct batched special pagetable update requests to map I/O
memory (in ioremap()).
[akpm@linux-foundation.org: fix warning, unpleasantly]
Signed-off-by: Ian Pratt <ian.pratt@xensource.com>
Signed-off-by: Christian Limpach <Christian.Limpach@cl.cam.ac.uk>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Christoph Lameter <clameter@sgi.com>
Cc: Matt Mackall <mpm@waste.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add a NOPFN_REFAULT return code for vm_ops->nopfn() equivalent to
NOPAGE_REFAULT for vmops->nopage() indicating that the handler requests a
re-execution of the faulting instruction
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add a vm_insert_pfn helper, so that ->fault handlers can have nopfn
functionality by installing their own pte and returning NULL.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
A variety of (mostly) innocuous fixes to the embedded kernel-doc content in
source files, including:
* make multi-line initial descriptions single line
* denote some function names, constants and structs as such
* change erroneous opening '/*' to '/**' in a few places
* reword some text for clarity
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Cc: "Randy.Dunlap" <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When kernel unmaps an address range, it needs to transfer PTE state into
page struct. Currently, kernel transfer access bit via
mark_page_accessed(). The call to mark_page_accessed in the unmap path
doesn't look logically correct.
At unmap time, calling mark_page_accessed will causes page LRU state to be
bumped up one step closer to more recently used state. It is causing quite
a bit headache in a scenario when a process creates a shmem segment, touch
a whole bunch of pages, then unmaps it. The unmapping takes a long time
because mark_page_accessed() will start moving pages from inactive to
active list.
I'm not too much concerned with moving the page from one list to another in
LRU. Sooner or later it might be moved because of multiple mappings from
various processes. But it just doesn't look logical that when user asks a
range to be unmapped, it's his intention that the process is no longer
interested in these pages. Moving those pages to active list (or bumping
up a state towards more active) seems to be an over reaction. It also
prolongs unmapping latency which is the core issue I'm trying to solve.
As suggested by Peter, we should still preserve the info on pte young
pages, but not more.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Ken Chen <kenchen@google.com>
Cc: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
After do_wp_page has tested page_mkwrite, it must release old_page after
acquiring page table lock, not before: at some stage that ordering got
reversed, leaving a (very unlikely) window in which old_page might be
truncated, freed, and reused in the same position.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Acked-by: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch fixes core dumps to include the vDSO vma, which is left out now.
It removes the special-case core writing macros, which were not doing the
right thing for the vDSO vma anyway. Instead, it uses VM_ALWAYSDUMP in the
vma; there is no need for the fixmap page to be installed. It handles the
CONFIG_COMPAT_VDSO case by making elf_core_dump use the fake vma from
get_gate_vma after real vmas in the same way the /proc/PID/maps code does.
This changes core dumps so they no longer include the non-PT_LOAD phdrs from
the vDSO. I made the change to add them in the first place, but in turned out
that nothing ever wanted them there since the advent of NT_AUXV. It's cleaner
to leave them out, and just let the phdrs inside the vDSO image speak for
themselves.
Signed-off-by: Roland McGrath <roland@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch fixes the initialization of gate_vma.vm_flags and
gate_vma.vm_page_prot to reflect reality. This makes the "[vdso]" line in
/proc/PID/maps correctly show r-xp instead of ---p, when gate_vma is used
(CONFIG_COMPAT_VDSO on i386).
Signed-off-by: Roland McGrath <roland@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Since get_user_pages() may be used with processes other than the
current process and calls flush_anon_page(), flush_anon_page() has to
cope in some way with non-current processes.
It may not be appropriate, or even desirable to flush a region of
virtual memory cache in the current process when that is different to
the process that we want the flush to occur for.
Therefore, pass the vma into flush_anon_page() so that the architecture
can work out whether the 'vmaddr' is for the current process or not.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Add more debugging in the rmap code in an attempt to locate to source of
the occasional "mapcount went negative" assertions.
Cc: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
To allow a more effective copy_user_highpage() on certain architectures,
a vma argument is added to the function and cow_user_page() allowing
the implementation of these functions to check for the VM_EXEC bit.
The main part of this patch was originally written by Ralf Baechle;
Atushi Nemoto did the the debugging.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Ramiro Voicu hits the BUG_ON(!pte_none(*pte)) in zeromap_pte_range: kernel
bugzilla 7645. Right: read_zero_pagealigned uses down_read of mmap_sem,
but another thread's racing read of /dev/zero, or a normal fault, can
easily set that pte again, in between zap_page_range and zeromap_page_range
getting there. It's been wrong ever since 2.4.3.
The simple fix is to use down_write instead, but that would serialize reads
of /dev/zero more than at present: perhaps some app would be badly
affected. So instead let zeromap_page_range return the error instead of
BUG_ON, and read_zero_pagealigned break to the slower clear_user loop in
that case - there's no need to optimize for it.
Use -EEXIST for when a pte is found: BUG_ON in mmap_zero (the other user of
zeromap_page_range), though it really isn't interesting there. And since
mmap_zero wants -EAGAIN for out-of-memory, the zeromaps better return that
than -ENOMEM.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: Ramiro Voicu: <Ramiro.Voicu@cern.ch>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
In time for 2.6.20, we can get rid of this junk.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Make sure the contention for the token happens _before_ any read-in and
kicks the swap-token algo only when the VM is under pressure.
Signed-off-by: Ashwin Chaugule <ashwin.chaugule@celunite.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
--=-=-=
from mm/memory.c:
1434 static inline void cow_user_page(struct page *dst, struct page *src, unsigned long va)
1435 {
1436 /*
1437 * If the source page was a PFN mapping, we don't have
1438 * a "struct page" for it. We do a best-effort copy by
1439 * just copying from the original user address. If that
1440 * fails, we just zero-fill it. Live with it.
1441 */
1442 if (unlikely(!src)) {
1443 void *kaddr = kmap_atomic(dst, KM_USER0);
1444 void __user *uaddr = (void __user *)(va & PAGE_MASK);
1445
1446 /*
1447 * This really shouldn't fail, because the page is there
1448 * in the page tables. But it might just be unreadable,
1449 * in which case we just give up and fill the result with
1450 * zeroes.
1451 */
1452 if (__copy_from_user_inatomic(kaddr, uaddr, PAGE_SIZE))
1453 memset(kaddr, 0, PAGE_SIZE);
1454 kunmap_atomic(kaddr, KM_USER0);
#### D-cache have to be flushed here.
#### It seems it is just forgotten.
1455 return;
1456
1457 }
1458 copy_user_highpage(dst, src, va);
#### Ok here. flush_dcache_page() called from this func if arch need it
1459 }
Following is the patch fix this issue:
Signed-off-by: Dmitriy Monakhov <dmonakhov@openvz.org>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Add a way for a no_page() handler to request a retry of the faulting
instruction. It goes back to userland on page faults and just tries again
in get_user_pages(). I added a cond_resched() in the loop in that later
case.
The problem I have with signal and spufs is an actual bug affecting apps and I
don't see other ways of fixing it.
In addition, we are having issues with infiniband and 64k pages (related to
the way the hypervisor deals with some HV cards) that will require us to muck
around with the MMU from within the IB driver's no_page() (it's a pSeries
specific driver) and return to the caller the same way using NOPAGE_REFAULT.
And to add to this, the graphics folks have been following a new approach of
memory management that involves transparently swapping objects between video
ram and main meory. To do that, they need installing PTEs from a no_page()
handler as well and that also requires returning with NOPAGE_REFAULT.
(For the later, they are currently using io_remap_pfn_range to install one PTE
from no_page() which is a bit racy, we need to add a check for the PTE having
already been installed afer taking the lock, but that's ok, they are only at
the proof-of-concept stage. I'll send a patch adding a "clean" function to do
that, we can use that from spufs too and get rid of the sparsemem hacks we do
to create struct page for SPEs. Basically, that provides a generic solution
for being able to have no_page() map hardware devices, which is something that
I think sound driver folks have been asking for some time too).
All of these things depend on having the NOPAGE_REFAULT exit path from
no_page() handlers.
Signed-off-by: Benjamin Herrenchmidt <benh@kernel.crashing.org>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Implement lazy MMU update hooks which are SMP safe for both direct and shadow
page tables. The idea is that PTE updates and page invalidations while in
lazy mode can be batched into a single hypercall. We use this in VMI for
shadow page table synchronization, and it is a win. It also can be used by
PPC and for direct page tables on Xen.
For SMP, the enter / leave must happen under protection of the page table
locks for page tables which are being modified. This is because otherwise,
you end up with stale state in the batched hypercall, which other CPUs can
race ahead of. Doing this under the protection of the locks guarantees the
synchronization is correct, and also means that spurious faults which are
generated during this window by remote CPUs are properly handled, as the page
fault handler must re-check the PTE under protection of the same lock.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Change pte_clear_full to a more appropriately named pte_clear_not_present,
allowing optimizations when not-present mapping changes need not be reflected
in the hardware TLB for protected page table modes. There is also another
case that can use it in the fremap code.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
We don't want to read PTEs directly like this after they have been modified,
as a lazy MMU implementation of direct page tables may not have written the
updated PTE back to memory yet.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Failing context is a multi threaded process context and the failing
sequence is as follows.
One thread T0 doing self modifying code on page X on processor P0 and
another thread T1 doing COW (breaking the COW setup as part of just
happened fork() in another thread T2) on the same page X on processor P1.
T0 doing SMC can endup modifying the new page Y (allocated by the T1 doing
COW on P1) but because of different I/D TLB's, P0 ITLB will not see the new
mapping till the flush TLB IPI from P1 is received. During this interval,
if T0 executes the code created by SMC it can result in an app error (as
ITLB still points to old page X and endup executing the content in page X
rather than using the content in page Y).
Fix this issue by first clearing the PTE and flushing it, before updating
it with new entry.
Hugh sayeth:
I was a bit sceptical, in the habit of thinking that Self Modifying Code
must look such issues itself: but I guess there's nothing it can do to avoid
this one.
Fair enough, what you're changing it to is pretty much what powerpc and
s390 were already doing, and is a more robust way of proceeding, consistent
with how ptes are set everywhere else.
The ptep_clear_flush is a bit heavy-handed (it's anxious to return the pte
that was atomically cleared), but we'd have to wander through lots of arches
to get the right minimal behaviour. It'd also be nice to eliminate
ptep_establish completely, now only used to define other macros/inlines: it
always seemed obfuscation to me, what you've got there now is clearer.
Let's put those cleanups on a TODO list.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Acked-by: "David S. Miller" <davem@davemloft.net>
Acked-by: Hugh Dickins <hugh@veritas.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Check that access_process_vm() is accessing a valid mapping in the target
process.
This limits ptrace() accesses and accesses through /proc/<pid>/maps to only
those regions actually mapped by a program.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Implement do_no_pfn() for handling mapping of memory without a struct page
backing it. This avoids creating fake page table entries for regions which
are not backed by real memory.
This feature is used by the MSPEC driver and other users, where it is
highly undesirable to have a struct page sitting behind the page (for
instance if the page is accessed in cached mode via the struct page in
parallel to the the driver accessing it uncached, which can result in data
corruption on some architectures, such as ia64).
This version uses specific NOPFN_{SIGBUS,OOM} return values, rather than
expect all negative pfn values would be an error. It also bugs on cow
mappings as this would not work with the VM.
[akpm@osdl.org: micro-optimise]
Signed-off-by: Jes Sorensen <jes@sgi.com>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
These functions are already documented quite well with long comments. Now
add kerneldoc style header to make this turn up in everyones favorite doc
format.
Signed-off-by: Rolf Eike Beer <eike-kernel@sf-tec.de>
Cc: "Randy.Dunlap" <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Wrt. the recent modifications in do_wp_page() Hugh Dickins pointed out:
"I now realize it's right to the first order (normal case) and to the
second order (ptrace poke), but not to the third order (ptrace poke
anon page here to be COWed - perhaps can't occur without intervening
mprotects)."
This patch restores the old COW behaviour for anonymous pages.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Now that we can detect writers of shared mappings, throttle them. Avoids OOM
by surprise.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Tracking of dirty pages in shared writeable mmap()s.
The idea is simple: write protect clean shared writeable pages, catch the
write-fault, make writeable and set dirty. On page write-back clean all the
PTE dirty bits and write protect them once again.
The implementation is a tad harder, mainly because the default
backing_dev_info capabilities were too loosely maintained. Hence it is not
enough to test the backing_dev_info for cap_account_dirty.
The current heuristic is as follows, a VMA is eligible when:
- its shared writeable
(vm_flags & (VM_WRITE|VM_SHARED)) == (VM_WRITE|VM_SHARED)
- it is not a 'special' mapping
(vm_flags & (VM_PFNMAP|VM_INSERTPAGE)) == 0
- the backing_dev_info is cap_account_dirty
mapping_cap_account_dirty(vma->vm_file->f_mapping)
- f_op->mmap() didn't change the default page protection
Page from remap_pfn_range() are explicitly excluded because their COW
semantics are already horrid enough (see vm_normal_page() in do_wp_page()) and
because they don't have a backing store anyway.
mprotect() is taught about the new behaviour as well. However it overrides
the last condition.
Cleaning the pages on write-back is done with page_mkclean() a new rmap call.
It can be called on any page, but is currently only implemented for mapped
pages, if the page is found the be of a VMA that accounts dirty pages it will
also wrprotect the PTE.
Finally, in fs/buffers.c:try_to_free_buffers(); remove clear_page_dirty() from
under ->private_lock. This seems to be safe, since ->private_lock is used to
serialize access to the buffers, not the page itself. This is needed because
clear_page_dirty() will call into page_mkclean() and would thereby violate
locking order.
[dhowells@redhat.com: Provide a page_mkclean() implementation for NOMMU]
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Hugh Dickins <hugh@veritas.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Unlike earlier iterations of the delay accounting patches, now delays are only
collected for the actual I/O waits rather than try and cover the delays seen
in I/O submission paths.
Account separately for block I/O delays incurred as a result of swapin page
faults whose frequency can be affected by the task/process' rss limit. Hence
swapin delays can act as feedback for rss limit changes independent of I/O
priority changes.
Signed-off-by: Shailabh Nagar <nagar@watson.ibm.com>
Signed-off-by: Balbir Singh <balbir@in.ibm.com>
Cc: Jes Sorensen <jes@sgi.com>
Cc: Peter Chubb <peterc@gelato.unsw.edu.au>
Cc: Erich Focht <efocht@ess.nec.de>
Cc: Levent Serinol <lserinol@gmail.com>
Cc: Jay Lan <jlan@engr.sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
