| Age | Commit message (Collapse) | Author |
|---|
|
Enumerate the DOI list through the NLBL_CALIPSO_C_LISTALL command.
It takes no attributes.
Signed-off-by: Huw Davies <huw@codeweavers.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
|
|
Query a specified DOI through the NLBL_CALIPSO_C_LIST command.
It requires the attribute:
NLBL_CALIPSO_A_DOI.
The reply will contain:
NLBL_CALIPSO_A_MTYPE
Signed-off-by: Huw Davies <huw@codeweavers.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
|
|
CALIPSO is a packet labelling protocol for IPv6 which is very similar
to CIPSO. It is specified in RFC 5570. Much of the code is based on
the current CIPSO code.
This adds support for adding passthrough-type CALIPSO DOIs through the
NLBL_CALIPSO_C_ADD command. It requires attributes:
NLBL_CALIPSO_A_TYPE which must be CALIPSO_MAP_PASS.
NLBL_CALIPSO_A_DOI.
In passthrough mode the CALIPSO engine will map MLS secattr levels
and categories directly to the packet label.
At this stage, the major difference between this and the CIPSO
code is that IPv6 may be compiled as a module. To allow for
this the CALIPSO functions are registered at module init time.
Signed-off-by: Huw Davies <huw@codeweavers.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs into next
|
|
Here's a set of patches that changes how certificates/keys are determined
to be trusted. That's currently a two-step process:
(1) Up until recently, when an X.509 certificate was parsed - no matter
the source - it was judged against the keys in .system_keyring,
assuming those keys to be trusted if they have KEY_FLAG_TRUSTED set
upon them.
This has just been changed such that any key in the .ima_mok keyring,
if configured, may also be used to judge the trustworthiness of a new
certificate, whether or not the .ima_mok keyring is meant to be
consulted for whatever process is being undertaken.
If a certificate is determined to be trustworthy, KEY_FLAG_TRUSTED
will be set upon a key it is loaded into (if it is loaded into one),
no matter what the key is going to be loaded for.
(2) If an X.509 certificate is loaded into a key, then that key - if
KEY_FLAG_TRUSTED gets set upon it - can be linked into any keyring
with KEY_FLAG_TRUSTED_ONLY set upon it. This was meant to be the
system keyring only, but has been extended to various IMA keyrings.
A user can at will link any key marked KEY_FLAG_TRUSTED into any
keyring marked KEY_FLAG_TRUSTED_ONLY if the relevant permissions masks
permit it.
These patches change that:
(1) Trust becomes a matter of consulting the ring of trusted keys supplied
when the trust is evaluated only.
(2) Every keyring can be supplied with its own manager function to
restrict what may be added to that keyring. This is called whenever a
key is to be linked into the keyring to guard against a key being
created in one keyring and then linked across.
This function is supplied with the keyring and the key type and
payload[*] of the key being linked in for use in its evaluation. It
is permitted to use other data also, such as the contents of other
keyrings such as the system keyrings.
[*] The type and payload are supplied instead of a key because as an
optimisation this function may be called whilst creating a key and
so may reject the proposed key between preparse and allocation.
(3) A default manager function is provided that permits keys to be
restricted to only asymmetric keys that are vouched for by the
contents of the system keyring.
A second manager function is provided that just rejects with EPERM.
(4) A key allocation flag, KEY_ALLOC_BYPASS_RESTRICTION, is made available
so that the kernel can initialise keyrings with keys that form the
root of the trust relationship.
(5) KEY_FLAG_TRUSTED and KEY_FLAG_TRUSTED_ONLY are removed, along with
key_preparsed_payload::trusted.
This change also makes it possible in future for userspace to create a private
set of trusted keys and then to have it sealed by setting a manager function
where the private set is wholly independent of the kernel's trust
relationships.
Further changes in the set involve extracting certain IMA special keyrings
and making them generally global:
(*) .system_keyring is renamed to .builtin_trusted_keys and remains read
only. It carries only keys built in to the kernel. It may be where
UEFI keys should be loaded - though that could better be the new
secondary keyring (see below) or a separate UEFI keyring.
(*) An optional secondary system keyring (called .secondary_trusted_keys)
is added to replace the IMA MOK keyring.
(*) Keys can be added to the secondary keyring by root if the keys can
be vouched for by either ring of system keys.
(*) Module signing and kexec only use .builtin_trusted_keys and do not use
the new secondary keyring.
(*) Config option SYSTEM_TRUSTED_KEYS now depends on ASYMMETRIC_KEY_TYPE as
that's the only type currently permitted on the system keyrings.
(*) A new config option, IMA_KEYRINGS_PERMIT_SIGNED_BY_BUILTIN_OR_SECONDARY,
is provided to allow keys to be added to IMA keyrings, subject to the
restriction that such keys are validly signed by a key already in the
system keyrings.
If this option is enabled, but secondary keyrings aren't, additions to
the IMA keyrings will be restricted to signatures verifiable by keys in
the builtin system keyring only.
Signed-off-by: David Howells <dhowells@redhat.com>
|
|
Commit 3034a14 "ima: pass 'opened' flag to identify newly created files"
stopped identifying empty files as new files. However new empty files
can be created using the mknodat syscall. On systems with IMA-appraisal
enabled, these empty files are not labeled with security.ima extended
attributes properly, preventing them from subsequently being opened in
order to write the file data contents. This patch defines a new hook
named ima_post_path_mknod() to mark these empty files, created using
mknodat, as new in order to allow the file data contents to be written.
In addition, files with security.ima xattrs containing a file signature
are considered "immutable" and can not be modified. The file contents
need to be written, before signing the file. This patch relaxes this
requirement for new files, allowing the file signature to be written
before the file contents.
Changelog:
- defer identifying files with signatures stored as security.ima
(based on Dmitry Rozhkov's comments)
- removing tests (eg. dentry, dentry->d_inode, inode->i_size == 0)
(based on Al's review)
Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Cc: Al Viro <<viro@zeniv.linux.org.uk>
Tested-by: Dmitry Rozhkov <dmitry.rozhkov@linux.intel.com>
|
|
When I was fixing up const recommendations from checkpatch.pl, I went
overboard. This fixes the warning (during a W=1 build):
include/linux/fs.h:2627:74: warning: type qualifiers ignored on function return type [-Wignored-qualifiers]
static inline const char * const kernel_read_file_id_str(enum kernel_read_file_id id)
Reported-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: James Morris <james.l.morris@oracle.com>
|
|
This LSM enforces that kernel-loaded files (modules, firmware, etc)
must all come from the same filesystem, with the expectation that
such a filesystem is backed by a read-only device such as dm-verity
or CDROM. This allows systems that have a verified and/or unchangeable
filesystem to enforce module and firmware loading restrictions without
needing to sign the files individually.
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
|
|
A string representation of the kernel_read_file_id enumeration is
needed for displaying messages (eg. pr_info, auditing) that can be
used by multiple LSMs and the integrity subsystem. To simplify
keeping the list of strings up to date with the enumeration, this
patch defines two new preprocessing macros named __fid_enumify and
__fid_stringify to create the enumeration and an array of strings.
kernel_read_file_id_str() returns a string based on the enumeration.
Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
[kees: removed removal of my old version, constified pointer values]
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: James Morris <james.l.morris@oracle.com>
|
|
Allocate a NULL-terminated file path with special characters escaped,
safe for logging.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: James Morris <james.l.morris@oracle.com>
|
|
Provide an escaped (but readable: no inter-argument NULLs) commandline
safe for logging.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: James Morris <james.l.morris@oracle.com>
|
|
Handle allocating and escaping a string safe for logging.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: James Morris <james.l.morris@oracle.com>
|
|
These commits do the following:
(1) Retain a signature in an asymmetric-type key and associate with it the
identifiers that will match a key that can be used to verify it.
(2) Differentiate an X.509 cert that cannot be used versus one that cannot
be verified due to unavailable crypto. This is noted in the
structures involved.
(3) Determination of the self-signedness of an X.509 cert is improved to
include checks on the subject/issuer names and the key
algorithm/signature algorithm types.
(4) Self-signed X.509 certificates are consistency checked early on if the
appropriate crypto is available.
Signed-off-by: David Howells <dhowells@redhat.com>
|
|
This adds userspace access to Diffie-Hellman computations through a
new keyctl() syscall command to calculate shared secrets or public
keys using input parameters stored in the keyring.
Input key ids are provided in a struct due to the current 5-arg limit
for the keyctl syscall. Only user keys are supported in order to avoid
exposing the content of logon or encrypted keys.
The output is written to the provided buffer, based on the assumption
that the values are only needed in userspace.
Future support for other types of key derivation would involve a new
command, like KEYCTL_ECDH_COMPUTE.
Once Diffie-Hellman support is included in the crypto API, this code
can be converted to use the crypto API to take advantage of possible
hardware acceleration and reduce redundant code.
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David Howells <dhowells@redhat.com>
|
|
Add a config option (IMA_KEYRINGS_PERMIT_SIGNED_BY_BUILTIN_OR_SECONDARY)
that, when enabled, allows keys to be added to the IMA keyrings by
userspace - with the restriction that each must be signed by a key in the
system trusted keyrings.
EPERM will be returned if this option is disabled, ENOKEY will be returned if
no authoritative key can be found and EKEYREJECTED will be returned if the
signature doesn't match. Other errors such as ENOPKG may also be returned.
If this new option is enabled, the builtin system keyring is searched, as is
the secondary system keyring if that is also enabled. Intermediate keys
between the builtin system keyring and the key being added can be added to
the secondary keyring (which replaces .ima_mok) to form a trust chain -
provided they are also validly signed by a key in one of the trusted keyrings.
The .ima_mok keyring is then removed and the IMA blacklist keyring gets its
own config option (IMA_BLACKLIST_KEYRING).
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
|
|
Add a secondary system keyring that can be added to by root whilst the
system is running - provided the key being added is vouched for by a key
built into the kernel or already added to the secondary keyring.
Rename .system_keyring to .builtin_trusted_keys to distinguish it more
obviously from the new keyring (called .secondary_trusted_keys).
The new keyring needs to be enabled with CONFIG_SECONDARY_TRUSTED_KEYRING.
If the secondary keyring is enabled, a link is created from that to
.builtin_trusted_keys so that the the latter will automatically be searched
too if the secondary keyring is searched.
Signed-off-by: David Howells <dhowells@redhat.com>
|
|
Remove KEY_FLAG_TRUSTED and KEY_ALLOC_TRUSTED as they're no longer
meaningful. Also we can drop the trusted flag from the preparse structure.
Given this, we no longer need to pass the key flags through to
restrict_link().
Further, we can now get rid of keyring_restrict_trusted_only() also.
Signed-off-by: David Howells <dhowells@redhat.com>
|
|
Move the point at which a key is determined to be trustworthy to
__key_link() so that we use the contents of the keyring being linked in to
to determine whether the key being linked in is trusted or not.
What is 'trusted' then becomes a matter of what's in the keyring.
Currently, the test is done when the key is parsed, but given that at that
point we can only sensibly refer to the contents of the system trusted
keyring, we can only use that as the basis for working out the
trustworthiness of a new key.
With this change, a trusted keyring is a set of keys that once the
trusted-only flag is set cannot be added to except by verification through
one of the contained keys.
Further, adding a key into a trusted keyring, whilst it might grant
trustworthiness in the context of that keyring, does not automatically
grant trustworthiness in the context of a second keyring to which it could
be secondarily linked.
To accomplish this, the authentication data associated with the key source
must now be retained. For an X.509 cert, this means the contents of the
AuthorityKeyIdentifier and the signature data.
If system keyrings are disabled then restrict_link_by_builtin_trusted()
resolves to restrict_link_reject(). The integrity digital signature code
still works correctly with this as it was previously using
KEY_FLAG_TRUSTED_ONLY, which doesn't permit anything to be added if there
is no system keyring against which trust can be determined.
Signed-off-by: David Howells <dhowells@redhat.com>
|
|
Generalise x509_request_asymmetric_key(). It doesn't really have any
dependencies on X.509 features as it uses generalised IDs and the
public_key structs that contain data extracted from X.509.
Signed-off-by: David Howells <dhowells@redhat.com>
|
|
Move x509_request_asymmetric_key() to asymmetric_type.c so that it can be
generalised.
Signed-off-by: David Howells <dhowells@redhat.com>
|
|
Add a facility whereby proposed new links to be added to a keyring can be
vetted, permitting them to be rejected if necessary. This can be used to
block public keys from which the signature cannot be verified or for which
the signature verification fails. It could also be used to provide
blacklisting.
This affects operations like add_key(), KEYCTL_LINK and KEYCTL_INSTANTIATE.
To this end:
(1) A function pointer is added to the key struct that, if set, points to
the vetting function. This is called as:
int (*restrict_link)(struct key *keyring,
const struct key_type *key_type,
unsigned long key_flags,
const union key_payload *key_payload),
where 'keyring' will be the keyring being added to, key_type and
key_payload will describe the key being added and key_flags[*] can be
AND'ed with KEY_FLAG_TRUSTED.
[*] This parameter will be removed in a later patch when
KEY_FLAG_TRUSTED is removed.
The function should return 0 to allow the link to take place or an
error (typically -ENOKEY, -ENOPKG or -EKEYREJECTED) to reject the
link.
The pointer should not be set directly, but rather should be set
through keyring_alloc().
Note that if called during add_key(), preparse is called before this
method, but a key isn't actually allocated until after this function
is called.
(2) KEY_ALLOC_BYPASS_RESTRICTION is added. This can be passed to
key_create_or_update() or key_instantiate_and_link() to bypass the
restriction check.
(3) KEY_FLAG_TRUSTED_ONLY is removed. The entire contents of a keyring
with this restriction emplaced can be considered 'trustworthy' by
virtue of being in the keyring when that keyring is consulted.
(4) key_alloc() and keyring_alloc() take an extra argument that will be
used to set restrict_link in the new key. This ensures that the
pointer is set before the key is published, thus preventing a window
of unrestrictedness. Normally this argument will be NULL.
(5) As a temporary affair, keyring_restrict_trusted_only() is added. It
should be passed to keyring_alloc() as the extra argument instead of
setting KEY_FLAG_TRUSTED_ONLY on a keyring. This will be replaced in
a later patch with functions that look in the appropriate places for
authoritative keys.
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
|
|
The skb_owned_by hook was added with the commit ca10b9e9a8ca
("selinux: add a skb_owned_by() hook") and later removed
when said commit was reverted.
Later on, when switching to list of hooks, a field named
'skb_owned_by' was included into the security_hook_head struct,
but without any users nor caller.
This commit removes the said left-over field.
Fixes: b1d9e6b0646d ("LSM: Switch to lists of hooks")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Casey Schaufler <casey@schaufler-ca.com>
Acked-by: Paul Moore <pmoore@paul-moore.com>
Signed-off-by: James Morris <james.l.morris@oracle.com>
|
|
Make the determination of the trustworthiness of a key dependent on whether
a key that can verify it is present in the supplied ring of trusted keys
rather than whether or not the verifying key has KEY_FLAG_TRUSTED set.
verify_pkcs7_signature() will return -ENOKEY if the PKCS#7 message trust
chain cannot be verified.
Signed-off-by: David Howells <dhowells@redhat.com>
|
|
Generalise system_verify_data() to provide access to internal content
through a callback. This allows all the PKCS#7 stuff to be hidden inside
this function and removed from the PE file parser and the PKCS#7 test key.
If external content is not required, NULL should be passed as data to the
function. If the callback is not required, that can be set to NULL.
The function is now called verify_pkcs7_signature() to contrast with
verify_pefile_signature() and the definitions of both have been moved into
linux/verification.h along with the key_being_used_for enum.
Signed-off-by: David Howells <dhowells@redhat.com>
|
|
Add key identifier pointers to public_key_signature struct so that they can
be used to retain the identifier of the key to be used to verify the
signature in both PKCS#7 and X.509.
Signed-off-by: David Howells <dhowells@redhat.com>
|
|
Allow authentication data to be stored in an asymmetric key in the 4th
element of the key payload and provide a way for it to be destroyed.
For the public key subtype, this will be a public_key_signature struct.
Signed-off-by: David Howells <dhowells@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull core kernel fixes from Ingo Molnar:
"This contains the nohz/atomic cleanup/fix for the fetch_or() ugliness
you noted during the original nohz pull request, plus there's also
misc fixes:
- fix liblockdep build bug
- fix uapi header build bug
- print more lockdep hash collision info to help debug recent reports
of hash collisions
- update MAINTAINERS email address"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
MAINTAINERS: Update my email address
locking/lockdep: Print chain_key collision information
uapi/linux/stddef.h: Provide __always_inline to userspace headers
tools/lib/lockdep: Fix unsupported 'basename -s' in run_tests.sh
locking/atomic, sched: Unexport fetch_or()
timers/nohz: Convert tick dependency mask to atomic_t
locking/atomic: Introduce atomic_fetch_or()
|
|
Pull SCSI target fixes from Nicholas Bellinger:
"This includes fixes from HCH for -rc1 configfs default_groups
conversion changes that ended up breaking some iscsi-target
default_groups, along with Sagi's ib_drain_qp() conversion for
iser-target to use the common caller now available to RDMA kernel
consumers in v4.6+ code"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
target: add a new add_wwn_groups fabrics method
target: initialize the nacl base CIT begfore init_nodeacl
target: remove ->fabric_cleanup_nodeacl
iser-target: Use ib_drain_qp
|
|
Pull configfs fix from Christoph Hellwig:
"A trivial fix to the recently introduced binary attribute helper
macros"
* tag 'configfs-for-linus-2' of git://git.infradead.org/users/hch/configfs:
configfs: fix CONFIGFS_BIN_ATTR_[RW]O definitions
|
|
Pull networking fixes from David Miller:
1) Missing device reference in IPSEC input path results in crashes
during device unregistration. From Subash Abhinov Kasiviswanathan.
2) Per-queue ISR register writes not being done properly in macb
driver, from Cyrille Pitchen.
3) Stats accounting bugs in bcmgenet, from Patri Gynther.
4) Lightweight tunnel's TTL and TOS were swapped in netlink dumps, from
Quentin Armitage.
5) SXGBE driver has off-by-one in probe error paths, from Rasmus
Villemoes.
6) Fix race in save/swap/delete options in netfilter ipset, from
Vishwanath Pai.
7) Ageing time of bridge not set properly when not operating over a
switchdev device. Fix from Haishuang Yan.
8) Fix GRO regression wrt nested FOU/GUE based tunnels, from Alexander
Duyck.
9) IPV6 UDP code bumps wrong stats, from Eric Dumazet.
10) FEC driver should only access registers that actually exist on the
given chipset, fix from Fabio Estevam.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (73 commits)
net: mvneta: fix changing MTU when using per-cpu processing
stmmac: fix MDIO settings
Revert "stmmac: Fix 'eth0: No PHY found' regression"
stmmac: fix TX normal DESC
net: mvneta: use cache_line_size() to get cacheline size
net: mvpp2: use cache_line_size() to get cacheline size
net: mvpp2: fix maybe-uninitialized warning
tun, bpf: fix suspicious RCU usage in tun_{attach, detach}_filter
net: usb: cdc_ncm: adding Telit LE910 V2 mobile broadband card
rtnl: fix msg size calculation in if_nlmsg_size()
fec: Do not access unexisting register in Coldfire
net: mvneta: replace MVNETA_CPU_D_CACHE_LINE_SIZE with L1_CACHE_BYTES
net: mvpp2: replace MVPP2_CPU_D_CACHE_LINE_SIZE with L1_CACHE_BYTES
net: dsa: mv88e6xxx: Clear the PDOWN bit on setup
net: dsa: mv88e6xxx: Introduce _mv88e6xxx_phy_page_{read, write}
bpf: make padding in bpf_tunnel_key explicit
ipv6: udp: fix UDP_MIB_IGNOREDMULTI updates
bnxt_en: Fix ethtool -a reporting.
bnxt_en: Fix typo in bnxt_hwrm_set_pause_common().
bnxt_en: Implement proper firmware message padding.
...
|
|
Page isolation has not failed if the fin pfn extends beyond the end pfn
and test_pages_isolated checks this correctly. Fix the tracepoint to
report the same result as the actual check function.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Joonsoo Kim <js1304@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The return value of pmd_trans_huge_lock() is a pointer, not a boolean
value, so use NULL instead of false as the return value.
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Initially the phy_bus_name was added to manipulate the
driver name but it was recently just used to manage the
fixed-link and then to take some decision at run-time.
So the patch uses the is_pseudo_fixed_link and removes
the phy_bus_name variable not necessary anymore.
The driver can manage the mdio registration by using phy-handle,
dwmac-mdio and own parameter e.g. snps,phy-addr.
This patch takes care about all these possible configurations
and fixes the mdio registration in case of there is a real
transceiver or a switch (that needs to be managed by using
fixed-link).
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Tested-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Cc: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Phil Reid <preid@electromag.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 88f8b1bb41c6208f81b6a480244533ded7b59493.
due to problems on GeekBox and Banana Pi M1 board when
connected to a real transceiver instead of a switch via
fixed-link.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Cc: Andreas Färber <afaerber@suse.de>
Cc: Frank Schäfer <fschaefer.oss@googlemail.com>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Sasha Levin reported a suspicious rcu_dereference_protected() warning
found while fuzzing with trinity that is similar to this one:
[ 52.765684] net/core/filter.c:2262 suspicious rcu_dereference_protected() usage!
[ 52.765688] other info that might help us debug this:
[ 52.765695] rcu_scheduler_active = 1, debug_locks = 1
[ 52.765701] 1 lock held by a.out/1525:
[ 52.765704] #0: (rtnl_mutex){+.+.+.}, at: [<ffffffff816a64b7>] rtnl_lock+0x17/0x20
[ 52.765721] stack backtrace:
[ 52.765728] CPU: 1 PID: 1525 Comm: a.out Not tainted 4.5.0+ #264
[...]
[ 52.765768] Call Trace:
[ 52.765775] [<ffffffff813e488d>] dump_stack+0x85/0xc8
[ 52.765784] [<ffffffff810f2fa5>] lockdep_rcu_suspicious+0xd5/0x110
[ 52.765792] [<ffffffff816afdc2>] sk_detach_filter+0x82/0x90
[ 52.765801] [<ffffffffa0883425>] tun_detach_filter+0x35/0x90 [tun]
[ 52.765810] [<ffffffffa0884ed4>] __tun_chr_ioctl+0x354/0x1130 [tun]
[ 52.765818] [<ffffffff8136fed0>] ? selinux_file_ioctl+0x130/0x210
[ 52.765827] [<ffffffffa0885ce3>] tun_chr_ioctl+0x13/0x20 [tun]
[ 52.765834] [<ffffffff81260ea6>] do_vfs_ioctl+0x96/0x690
[ 52.765843] [<ffffffff81364af3>] ? security_file_ioctl+0x43/0x60
[ 52.765850] [<ffffffff81261519>] SyS_ioctl+0x79/0x90
[ 52.765858] [<ffffffff81003ba2>] do_syscall_64+0x62/0x140
[ 52.765866] [<ffffffff817d563f>] entry_SYSCALL64_slow_path+0x25/0x25
Same can be triggered with PROVE_RCU (+ PROVE_RCU_REPEATEDLY) enabled
from tun_attach_filter() when user space calls ioctl(tun_fd, TUN{ATTACH,
DETACH}FILTER, ...) for adding/removing a BPF filter on tap devices.
Since the fix in f91ff5b9ff52 ("net: sk_{detach|attach}_filter() rcu
fixes") sk_attach_filter()/sk_detach_filter() now dereferences the
filter with rcu_dereference_protected(), checking whether socket lock
is held in control path.
Since its introduction in 994051625981 ("tun: socket filter support"),
tap filters are managed under RTNL lock from __tun_chr_ioctl(). Thus the
sock_owned_by_user(sk) doesn't apply in this specific case and therefore
triggers the false positive.
Extend the BPF API with __sk_attach_filter()/__sk_detach_filter() pair
that is used by tap filters and pass in lockdep_rtnl_is_held() for the
rcu_dereference_protected() checks instead.
Reported-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We need to have the WWN fully initialized before addig default groups to it,
so add a new method to add these groups after the WWN has been initialized.
Also remove the default groups in the core while we're at it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Instead we can clean up the list of default ACLs in core code.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Make the 2 byte padding in struct bpf_tunnel_key between tunnel_ttl
and tunnel_label members explicit. No issue has been observed, and
gcc/llvm does padding for the old struct already, where tunnel_label
was not yet present, so the current code works, but since it's part
of uapi, make sure we don't introduce holes in structs.
Therefore, add tunnel_ext that we can use generically in future
(f.e. to flag OAM messages for backends, etc). Also add the offset
to the compat tests to be sure should some compilers not padd the
tail of the old version of bpf_tunnel_key.
Fixes: 4018ab1875e0 ("bpf: support flow label for bpf_skb_{set, get}_tunnel_key")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Josh Boyer reported that my recent change to uapi/linux/swab.h broke the Qemu build:
bc27fb68aaad ("include/uapi/linux/byteorder, swab: force inlining of some byteswap operations")
Unfortunately, UAPI headers don't include compiler.h so fixing it there is not enough,
add an __always_inline definition to uapi/linux/stddef.h instead.
Testcase: "make headers_install" and try to compile this:
#include <linux/swab.h>
void main() {}
Reported-by: Josh Boyer <jwboyer@fedoraproject.org>
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: David Rientjes <rientjes@google.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Thomas Graf <tgraf@suug.ch>
Cc: linux-kernel@vger.kernel.org
Link: http://lkml.kernel.org/r/1459289697-12875-1-git-send-email-dvlasenk@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
This patch functionally reverts:
5fd7a09cfb8c ("atomic: Export fetch_or()")
During the merge Linus observed that the generic version of fetch_or()
was messy:
" This makes the ugly "fetch_or()" macro that the scheduler used
internally a new generic helper, and does a bad job at it. "
e23604edac2a Merge branch 'timers-nohz-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Now that we have introduced atomic_fetch_or(), fetch_or() is only used
by the scheduler in order to deal with thread_info flags which type
can vary across architectures.
Lets confine fetch_or() back to the scheduler so that we encourage
future users to use the more robust and well typed atomic_t version
instead.
While at it, fetch_or() gets robustified, pasting improvements from a
previous patch by Ingo Molnar that avoids needless expression
re-evaluations in the loop.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1458830281-4255-4-git-send-email-fweisbec@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
The tick dependency mask was intially unsigned long because this is the
type on which clear_bit() operates on and fetch_or() accepts it.
But now that we have atomic_fetch_or(), we can instead use
atomic_andnot() to clear the bit. This consolidates the type of our
tick dependency mask, reduce its size on structures and benefit from
possible architecture optimizations on atomic_t operations.
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1458830281-4255-3-git-send-email-fweisbec@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
This is deemed to replace the type generic fetch_or() which brings a lot
of issues such as macro induced block variable aliasing and sloppy types.
Not to mention fetch_or() doesn't refer to any namespace, adding even
more confusion.
So lets provide an atomic_t version. Current and next users of fetch_or()
are thus encouraged to use atomic_t.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1458830281-4255-2-git-send-email-fweisbec@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Update the definition of memcpy_from_pmem() to return 0 or a negative
error code. Implement x86/arch_memcpy_from_pmem() with memcpy_mcsafe().
Cc: Borislav Petkov <bp@alien8.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
This fix adds a new reference counter (ref_netlink) for the struct ip_set.
The other reference counter (ref) can be swapped out by ip_set_swap and we
need a separate counter to keep track of references for netlink events
like dump. Using the same ref counter for dump causes a race condition
which can be demonstrated by the following script:
ipset create hash_ip1 hash:ip family inet hashsize 1024 maxelem 500000 \
counters
ipset create hash_ip2 hash:ip family inet hashsize 300000 maxelem 500000 \
counters
ipset create hash_ip3 hash:ip family inet hashsize 1024 maxelem 500000 \
counters
ipset save &
ipset swap hash_ip3 hash_ip2
ipset destroy hash_ip3 /* will crash the machine */
Swap will exchange the values of ref so destroy will see ref = 0 instead of
ref = 1. With this fix in place swap will not succeed because ipset save
still has ref_netlink on the set (ip_set_swap doesn't swap ref_netlink).
Both delete and swap will error out if ref_netlink != 0 on the set.
Note: The changes to *_head functions is because previously we would
increment ref whenever we called these functions, we don't do that
anymore.
Reviewed-by: Joshua Hunt <johunt@akamai.com>
Signed-off-by: Vishwanath Pai <vpai@akamai.com>
Signed-off-by: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client
Pull Ceph updates from Sage Weil:
"There is quite a bit here, including some overdue refactoring and
cleanup on the mon_client and osd_client code from Ilya, scattered
writeback support for CephFS and a pile of bug fixes from Zheng, and a
few random cleanups and fixes from others"
[ I already decided not to pull this because of it having been rebased
recently, but ended up changing my mind after all. Next time I'll
really hold people to it. Oh well. - Linus ]
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client: (34 commits)
libceph: use KMEM_CACHE macro
ceph: use kmem_cache_zalloc
rbd: use KMEM_CACHE macro
ceph: use lookup request to revalidate dentry
ceph: kill ceph_get_dentry_parent_inode()
ceph: fix security xattr deadlock
ceph: don't request vxattrs from MDS
ceph: fix mounting same fs multiple times
ceph: remove unnecessary NULL check
ceph: avoid updating directory inode's i_size accidentally
ceph: fix race during filling readdir cache
libceph: use sizeof_footer() more
ceph: kill ceph_empty_snapc
ceph: fix a wrong comparison
ceph: replace CURRENT_TIME by current_fs_time()
ceph: scattered page writeback
libceph: add helper that duplicates last extent operation
libceph: enable large, variable-sized OSD requests
libceph: osdc->req_mempool should be backed by a slab pool
libceph: make r_request msg_size calculation clearer
...
|
|
Pull NTB bug fixes from Jon Mason:
"NTB bug fixes for tasklet from spinning forever, link errors,
translation window setup, NULL ptr dereference, and ntb-perf errors.
Also, a modification to the driver API that makes _addr functions
optional"
* tag 'ntb-4.6' of git://github.com/jonmason/ntb:
NTB: Remove _addr functions from ntb_hw_amd
NTB: Make _addr functions optional in the API
NTB: Fix incorrect clean up routine in ntb_perf
NTB: Fix incorrect return check in ntb_perf
ntb: fix possible NULL dereference
ntb: add missing setup of translation window
ntb: stop link work when we do not have memory
ntb: stop tasklet from spinning forever during shutdown.
ntb: perf test: fix address space confusion
|
|
Pull more SCSI updates from James Bottomley:
"The only new stuff which missed the first pull request is an update to
the UFS driver.
The rest is an assortment of bug fixes and minor tweaks which appeared
recently (some are fixes for recent code and some are stuff spotted
recently by the checkers or the new gcc-6 compiler [most of Arnd's
stuff])"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (32 commits)
scsi_common: do not clobber fixed sense information
scsi: ufs: select CONFIG_NLS
scsi: fc: use get/put_unaligned64 for wwn access
fnic: move printk()s outside of the critical code section.
qla2xxx: avoid maybe_uninitialized warning
megaraid_sas: add missing curly braces in ioctl handler
lpfc: fix misleading indentation
scsi_transport_sas: add 'scsi_target_id' sysfs attribute
scsi_dh_alua: uninitialized variable in alua_check_vpd()
scsi: ufs-qcom: add printouts of testbus debug registers
scsi: ufs-qcom: enable/disable the device ref clock
scsi: ufs-qcom: set PA_Local_TX_LCC_Enable before link startup
scsi: ufs: add device quirk delay before putting UFS rails in LPM
scsi: ufs: fix leakage during link off state
scsi: ufs: tune UniPro parameters to optimize hibern8 exit time
scsi: ufs: handle non spec compliant bkops behaviour by device
scsi: ufs: add retry for query descriptors
scsi: ufs: add error recovery after DL NAC error
scsi: ufs: make error handling bit faster
scsi: ufs: disable vccq if it's not needed by UFS device
...
|
|
Implement the stack depot and provide CONFIG_STACKDEPOT. Stack depot
will allow KASAN store allocation/deallocation stack traces for memory
chunks. The stack traces are stored in a hash table and referenced by
handles which reside in the kasan_alloc_meta and kasan_free_meta
structures in the allocated memory chunks.
IRQ stack traces are cut below the IRQ entry point to avoid unnecessary
duplication.
Right now stackdepot support is only enabled in SLAB allocator. Once
KASAN features in SLAB are on par with those in SLUB we can switch SLUB
to stackdepot as well, thus removing the dependency on SLUB stack
bookkeeping, which wastes a lot of memory.
This patch is based on the "mm: kasan: stack depots" patch originally
prepared by Dmitry Chernenkov.
Joonsoo has said that he plans to reuse the stackdepot code for the
mm/page_owner.c debugging facility.
[akpm@linux-foundation.org: s/depot_stack_handle/depot_stack_handle_t]
[aryabinin@virtuozzo.com: comment style fixes]
Signed-off-by: Alexander Potapenko <glider@google.com>
Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Andrey Konovalov <adech.fo@gmail.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Konstantin Serebryany <kcc@google.com>
Cc: Dmitry Chernenkov <dmitryc@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
KASAN needs to know whether the allocation happens in an IRQ handler.
This lets us strip everything below the IRQ entry point to reduce the
number of unique stack traces needed to be stored.
Move the definition of __irq_entry to <linux/interrupt.h> so that the
users don't need to pull in <linux/ftrace.h>. Also introduce the
__softirq_entry macro which is similar to __irq_entry, but puts the
corresponding functions to the .softirqentry.text section.
Signed-off-by: Alexander Potapenko <glider@google.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Andrey Konovalov <adech.fo@gmail.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Konstantin Serebryany <kcc@google.com>
Cc: Dmitry Chernenkov <dmitryc@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add GFP flags to KASAN hooks for future patches to use.
This patch is based on the "mm: kasan: unified support for SLUB and SLAB
allocators" patch originally prepared by Dmitry Chernenkov.
Signed-off-by: Alexander Potapenko <glider@google.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Andrey Konovalov <adech.fo@gmail.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Konstantin Serebryany <kcc@google.com>
Cc: Dmitry Chernenkov <dmitryc@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
