Age | Commit message (Collapse) | Author |
|
By now, bmap() will either return the physical block number related to
the requested file offset or 0 in case of error or the requested offset
maps into a hole.
This patch makes the needed changes to enable bmap() to proper return
errors, using the return value as an error return, and now, a pointer
must be passed to bmap() to be filled with the mapped physical block.
It will change the behavior of bmap() on return:
- negative value in case of error
- zero on success or map fell into a hole
In case of a hole, the *block will be zero too
Since this is a prep patch, by now, the only error return is -EINVAL if
->bmap doesn't exist.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Carlos Maiolino <cmaiolino@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
If CONFIG_MFD_SYSCON=n:
include/linux/mfd/syscon.h:54:23: warning: ‘syscon_regmap_lookup_by_phandle_args’ defined but not used [-Wunused-function]
Fix this by adding the missing inline keyword.
Fixes: 6a24f567af4accef ("mfd: syscon: Add arguments support for syscon reference")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pavel/linux-leds
Pull LED updates from Pavel Machek:
- New driver for TI TPS6105X
- Add managed API to get a LED from a device driver
- Misc fixes and updates
* tag 'leds-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/pavel/linux-leds: (22 commits)
leds: lm3692x: Disable chip on brightness 0
leds: lm3692x: Split out lm3692x_leds_disable
leds: lm3692x: Move lm3692x_init and rename to lm3692x_leds_enable
leds: lm3692x: Make sure we don't exceed the maximum LED current
dt: bindings: lm3692x: Add led-max-microamp property
leds: lm3692x: Allow to configure over voltage protection
dt: bindings: lm3692x: Add ti,ovp-microvolt property
leds: populate the device's of_node
leds: Add managed API to get a LED from a device driver
leds: Add of_led_get() and led_put()
leds: lm3532: add pointer to documentation and fix typo
leds: lm3532: use extended registration so that LED can be used for backlight
leds: lm3642: remove warnings for bad strtol, cleanup gotos
leds: rb532: cleanup whitespace
ledtrig-pattern: fix email address quoting in MODULE_AUTHOR()
dt-bindings: mfd: update TI tps6105x chip bindings
leds: tps6105x: add driver for MFD chip LED mode
led: max77650: add of_match table
leds: bd2802: Convert to use GPIO descriptors
leds: pca963x: Fix open-drain initialization
...
|
|
The dynevent_cmd commands that build up the command string don't need
to do that themselves - there's a seq_buf facility that does pretty
much the same thing those command are doing manually, so use it
instead.
Link: http://lkml.kernel.org/r/eb8a6e835c964d0ab8a38cbf5ffa60746b54a465.1580506712.git.zanussi@kernel.org
Reviewed-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Tom Zanussi <zanussi@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild updates from Masahiro Yamada:
- detect missing include guard in UAPI headers
- do not create orphan built-in.a or obj-y objects
- generate modules.builtin more simply, and drop tristate.conf
- simplify built-in initramfs creation
- make linux-headers deb package thinner
- optimize the deb package build script
- misc cleanups
* tag 'kbuild-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (34 commits)
builddeb: split libc headers deployment out into a function
builddeb: split kernel headers deployment out into a function
builddeb: remove redundant make for ARCH=um
builddeb: avoid invoking sub-shells where possible
builddeb: remove redundant $objtree/
builddeb: match temporary directory name to the package name
builddeb: remove unneeded files in hdrobjfiles for headers package
kbuild: use -S instead of -E for precise cc-option test in Kconfig
builddeb: allow selection of .deb compressor
kbuild: remove 'Building modules, stage 2.' log
kbuild: remove *.tmp file when filechk fails
kbuild: remove PYTHON2 variable
modpost: assume STT_SPARC_REGISTER is defined
gen_initramfs.sh: remove intermediate cpio_list on errors
initramfs: refactor the initramfs build rules
gen_initramfs.sh: always output cpio even without -o option
initramfs: add default_cpio_list, and delete -d option support
initramfs: generate dependency list and cpio at the same time
initramfs: specify $(src)/gen_initramfs.sh as a prerequisite in Makefile
initramfs: make initramfs compression choice non-optional
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random
Pull random changes from Ted Ts'o:
"Change /dev/random so that it uses the CRNG and only blocking if the
CRNG hasn't initialized, instead of the old blocking pool. Also clean
up archrandom.h, and some other miscellaneous cleanups"
* tag 'random_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/random: (24 commits)
s390x: Mark archrandom.h functions __must_check
powerpc: Mark archrandom.h functions __must_check
powerpc: Use bool in archrandom.h
x86: Mark archrandom.h functions __must_check
linux/random.h: Mark CONFIG_ARCH_RANDOM functions __must_check
linux/random.h: Use false with bool
linux/random.h: Remove arch_has_random, arch_has_random_seed
s390: Remove arch_has_random, arch_has_random_seed
powerpc: Remove arch_has_random, arch_has_random_seed
x86: Remove arch_has_random, arch_has_random_seed
random: remove some dead code of poolinfo
random: fix typo in add_timer_randomness()
random: Add and use pr_fmt()
random: convert to ENTROPY_BITS for better code readability
random: remove unnecessary unlikely()
random: remove kernel.random.read_wakeup_threshold
random: delete code to pull data into pools
random: remove the blocking pool
random: make /dev/random be almost like /dev/urandom
random: ignore GRND_RANDOM in getentropy(2)
...
|
|
Evan tracked down a subtle race between the update of the MSI message and
the device raising an interrupt internally on PCI devices which do not
support MSI masking. The update of the MSI message is non-atomic and
consists of either 2 or 3 sequential 32bit wide writes to the PCI config
space.
- Write address low 32bits
- Write address high 32bits (If supported by device)
- Write data
When an interrupt is migrated then both address and data might change, so
the kernel attempts to mask the MSI interrupt first. But for MSI masking is
optional, so there exist devices which do not provide it. That means that
if the device raises an interrupt internally between the writes then a MSI
message is sent built from half updated state.
On x86 this can lead to spurious interrupts on the wrong interrupt
vector when the affinity setting changes both address and data. As a
consequence the device interrupt can be lost causing the device to
become stuck or malfunctioning.
Evan tried to handle that by disabling MSI accross an MSI message
update. That's not feasible because disabling MSI has issues on its own:
If MSI is disabled the PCI device is routing an interrupt to the legacy
INTx mechanism. The INTx delivery can be disabled, but the disablement is
not working on all devices.
Some devices lose interrupts when both MSI and INTx delivery are disabled.
Another way to solve this would be to enforce the allocation of the same
vector on all CPUs in the system for this kind of screwed devices. That
could be done, but it would bring back the vector space exhaustion problems
which got solved a few years ago.
Fortunately the high address (if supported by the device) is only relevant
when X2APIC is enabled which implies interrupt remapping. In the interrupt
remapping case the affinity setting is happening at the interrupt remapping
unit and the PCI MSI message is programmed only once when the PCI device is
initialized.
That makes it possible to solve it with a two step update:
1) Target the MSI msg to the new vector on the current target CPU
2) Target the MSI msg to the new vector on the new target CPU
In both cases writing the MSI message is only changing a single 32bit word
which prevents the issue of inconsistency.
After writing the final destination it is necessary to check whether the
device issued an interrupt while the intermediate state #1 (new vector,
current CPU) was in effect.
This is possible because the affinity change is always happening on the
current target CPU. The code runs with interrupts disabled, so the
interrupt can be detected by checking the IRR of the local APIC. If the
vector is pending in the IRR then the interrupt is retriggered on the new
target CPU by sending an IPI for the associated vector on the target CPU.
This can cause spurious interrupts on both the local and the new target
CPU.
1) If the new vector is not in use on the local CPU and the device
affected by the affinity change raised an interrupt during the
transitional state (step #1 above) then interrupt entry code will
ignore that spurious interrupt. The vector is marked so that the
'No irq handler for vector' warning is supressed once.
2) If the new vector is in use already on the local CPU then the IRR check
might see an pending interrupt from the device which is using this
vector. The IPI to the new target CPU will then invoke the handler of
the device, which got the affinity change, even if that device did not
issue an interrupt
3) If the new vector is in use already on the local CPU and the device
affected by the affinity change raised an interrupt during the
transitional state (step #1 above) then the handler of the device which
uses that vector on the local CPU will be invoked.
expose issues in device driver interrupt handlers which are not prepared to
handle a spurious interrupt correctly. This not a regression, it's just
exposing something which was already broken as spurious interrupts can
happen for a lot of reasons and all driver handlers need to be able to deal
with them.
Reported-by: Evan Green <evgreen@chromium.org>
Debugged-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Evan Green <evgreen@chromium.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/87imkr4s7n.fsf@nanos.tec.linutronix.de
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"Resource management:
- Improve resource assignment for hot-added nested bridges, e.g.,
Thunderbolt (Nicholas Johnson)
Power management:
- Optionally print config space of devices before suspend (Chen Yu)
- Increase D3 delay for AMD Ryzen5/7 XHCI controllers (Daniel Drake)
Virtualization:
- Generalize DMA alias quirks (James Sewart)
- Add DMA alias quirk for PLX PEX NTB (James Sewart)
- Fix IOV memory leak (Navid Emamdoost)
AER:
- Log which device prevents error recovery (Yicong Yang)
Peer-to-peer DMA:
- Whitelist Intel SkyLake-E (Armen Baloyan)
Broadcom iProc host bridge driver:
- Apply PAXC quirk whether driver is built-in or module (Wei Liu)
Broadcom STB host bridge driver:
- Add Broadcom STB PCIe host controller driver (Jim Quinlan)
Intel Gateway SoC host bridge driver:
- Add driver for Intel Gateway SoC (Dilip Kota)
Intel VMD host bridge driver:
- Add support for DMA aliases on other buses (Jon Derrick)
- Remove dma_map_ops overrides (Jon Derrick)
- Remove now-unused X86_DEV_DMA_OPS (Christoph Hellwig)
NVIDIA Tegra host bridge driver:
- Fix Tegra30 afi_pex2_ctrl register offset (Marcel Ziswiler)
Panasonic UniPhier host bridge driver:
- Remove module code since driver can't be built as a module
(Masahiro Yamada)
Qualcomm host bridge driver:
- Add support for SDM845 PCIe controller (Bjorn Andersson)
TI Keystone host bridge driver:
- Fix "num-viewport" DT property error handling (Kishon Vijay Abraham I)
- Fix link training retries initiation (Yurii Monakov)
- Fix outbound region mapping (Yurii Monakov)
Misc:
- Add Switchtec Gen4 support (Kelvin Cao)
- Add Switchtec Intercomm Notify and Upstream Error Containment
support (Logan Gunthorpe)
- Use dma_set_mask_and_coherent() since Switchtec supports 64-bit
addressing (Wesley Sheng)"
* tag 'pci-v5.6-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (60 commits)
PCI: Allow adjust_bridge_window() to shrink resource if necessary
PCI: Set resource size directly in adjust_bridge_window()
PCI: Rename extend_bridge_window() to adjust_bridge_window()
PCI: Rename extend_bridge_window() parameter
PCI: Consider alignment of hot-added bridges when assigning resources
PCI: Remove local variable usage in pci_bus_distribute_available_resources()
PCI: Pass size + alignment to pci_bus_distribute_available_resources()
PCI: Rename variables
PCI: vmd: Add two VMD Device IDs
PCI: Remove unnecessary braces
PCI: brcmstb: Add MSI support
PCI: brcmstb: Add Broadcom STB PCIe host controller driver
x86/PCI: Remove X86_DEV_DMA_OPS
PCI: vmd: Remove dma_map_ops overrides
iommu/vt-d: Remove VMD child device sanity check
iommu/vt-d: Use pci_real_dma_dev() for mapping
PCI: Introduce pci_real_dma_dev()
x86/PCI: Expose VMD's pci_dev in struct pci_sysdata
x86/PCI: Add to_pci_sysdata() helper
PCI/AER: Initialize aer_fifo
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- New staging driver for Rockship ISPv1 unit
- New staging driver for Rockchip MIPI Synopsys DPHY RX0
- y2038 fixes at V4L2 API (backward-compatible)
- A dvb core fix when receiving invalid EIT sections
- Some clang-specific warnings got fixed
- Added support for touch V4L2 interface at vivid
- Several drivers were converted to use the new
i2c_new_scanned_device() kAPI
- Added sm1 support at meson's vdec driver
- Several other driver cleanups, fixes and improvements
* tag 'media/v5.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (207 commits)
media: staging/intel-ipu3: remove TODO item about acronyms
media: v4l2-fwnode: Print the node name while parsing endpoints
media: Revert "media: staging/intel-ipu3: make imgu use fixed running mode"
media: mt9v111: constify copied structure
media: platform: VIDEO_MEDIATEK_JPEG can also depend on MTK_IOMMU
media: uvcvideo: Add a quirk to force GEO GC6500 Camera bits-per-pixel value
media: uvcvideo: Avoid cyclic entity chains due to malformed USB descriptors
media: hantro: fix post-processing NULL pointer dereference
media: rcar-vin: Use correct pixel format when aligning format
media: MAINTAINERS: add entry for Rockchip ISP1 driver
media: staging: rkisp1: add TODO file for staging
media: staging: rkisp1: add document for rkisp1 meta buffer format
media: staging: rkisp1: add output device for parameters
media: staging: rkisp1: add capture device for statistics
media: staging: rkisp1: add user space ABI definitions
media: staging: rkisp1: add streaming paths
media: staging: rkisp1: add Rockchip ISP1 base driver
media: staging: phy-rockchip-dphy-rx0: add Rockchip MIPI Synopsys DPHY RX0 driver
media: staging: dt-bindings: add Rockchip MIPI RX D-PHY RX0 yaml bindings
media: staging: dt-bindings: add Rockchip ISP1 yaml bindings
...
|
|
Pull rdma updates from Jason Gunthorpe:
"A very quiet cycle with few notable changes. Mostly the usual list of
one or two patches to drivers changing something that isn't quite rc
worthy. The subsystem seems to be seeing a larger number of rework and
cleanup style patches right now, I feel that several vendors are
prepping their drivers for new silicon.
Summary:
- Driver updates and cleanup for qedr, bnxt_re, hns, siw, mlx5, mlx4,
rxe, i40iw
- Larger series doing cleanup and rework for hns and hfi1.
- Some general reworking of the CM code to make it a little more
understandable
- Unify the different code paths connected to the uverbs FD scheme
- New UAPI ioctls conversions for get context and get async fd
- Trace points for CQ and CM portions of the RDMA stack
- mlx5 driver support for virtio-net formatted rings as RDMA raw
ethernet QPs
- verbs support for setting the PCI-E relaxed ordering bit on DMA
traffic connected to a MR
- A couple of bug fixes that came too late to make rc7"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (108 commits)
RDMA/core: Make the entire API tree static
RDMA/efa: Mask access flags with the correct optional range
RDMA/cma: Fix unbalanced cm_id reference count during address resolve
RDMA/umem: Fix ib_umem_find_best_pgsz()
IB/mlx4: Fix leak in id_map_find_del
IB/opa_vnic: Spelling correction of 'erorr' to 'error'
IB/hfi1: Fix logical condition in msix_request_irq
RDMA/cm: Remove CM message structs
RDMA/cm: Use IBA functions for complex structure members
RDMA/cm: Use IBA functions for simple structure members
RDMA/cm: Use IBA functions for swapping get/set acessors
RDMA/cm: Use IBA functions for simple get/set acessors
RDMA/cm: Add SET/GET implementations to hide IBA wire format
RDMA/cm: Add accessors for CM_REQ transport_type
IB/mlx5: Return the administrative GUID if exists
RDMA/core: Ensure that rdma_user_mmap_entry_remove() is a fence
IB/mlx4: Fix memory leak in add_gid error flow
IB/mlx5: Expose RoCE accelerator counters
RDMA/mlx5: Set relaxed ordering when requested
RDMA/core: Add the core support field to METHOD_GET_CONTEXT
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull more power manadement updates from Rafael Wysocki:
"Prevent cpufreq from creating excessively large stack frames and fix
the handling of devices deleted during system-wide resume in the PM
core (Rafael Wysocki), revert a problematic commit affecting the
cpupower utility and correct its man page (Thomas Renninger,
Brahadambal Srinivasan), and improve the intel_pstate_tracer utility
(Doug Smythies)"
* tag 'pm-5.6-rc1-2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
tools/power/x86/intel_pstate_tracer: change several graphs to autoscale y-axis
tools/power/x86/intel_pstate_tracer: changes for python 3 compatibility
Correction to manpage of cpupower
cpufreq: Avoid creating excessively large stack frames
PM: core: Fix handling of devices deleted during system-wide resume
cpupower: Revert library ABI changes from commit ae2917093fb60bdc1ed3e
|
|
'clk-freescale' and 'clk-qoriq' into clk-next
- Support for Xilinx Versal platform clks
- Display clk controller on qcom sc7180
- Video clk controller on qcom sc7180
- Graphics clk controller on qcom sc7180
- CPU PLLs for qcom msm8916
- Fixes for clk controllers on qcom msm8998 SoCs
- Move qcom msm8974 gfx3d clk to RPM control
- Display port clk support on qcom sdm845 SoCs
- Global clk controller on qcom ipq6018
- Adjust composite clk to new way of describing clk parents
- Add a driver for BCLK of Freescale SAI cores
* clk-imx: (32 commits)
clk: imx: Add support for i.MX8MP clock driver
dt-bindings: imx: Add clock binding doc for i.MX8MP
clk: imx: gate4: Switch imx_clk_gate4_flags() to clk_hw based API
clk: imx: imx8mq: Switch to clk_hw based API
clk: imx: imx8mm: Switch to clk_hw based API
clk: imx: imx8mn: Switch to clk_hw based API
clk: imx: Remove __init for imx_obtain_fixed_clk_hw() API
clk: imx: gate3: Switch to clk_hw based API
clk: imx: add hw API imx_clk_hw_mux2_flags
clk: imx: add imx_unregister_hw_clocks
clk: imx: clk-composite-8m: Switch to clk_hw based API
clk: imx: clk-pll14xx: Switch to clk_hw based API
clk: imx7up: Rename the clks to hws
clk: imx: Rename the imx_clk_divider_gate to imply it's clk_hw based
clk: imx: Rename the imx_clk_pfdv2 to imply it's clk_hw based
clk: imx: Rename the imx_clk_pllv4 to imply it's clk_hw based
clk: imx: Rename sccg and frac pll register to suggest clk_hw
clk: imx: imx7ulp composite: Rename to show is clk_hw based
clk: imx: pllv2: Switch to clk_hw based API
clk: imx: pllv1: Switch to clk_hw based API
...
* clk-ti:
clk: ti: clkctrl: Fix hidden dependency to node name
clk: ti: add clkctrl data dra7 sgx
clk: ti: omap5: Add missing AESS clock
clk: ti: dra7: fix parent for gmac_clkctrl
clk: ti: dra7: add vpe clkctrl data
clk: ti: dra7: add cam clkctrl data
dt-bindings: clock: Move ti-dra7-atl.h to dt-bindings/clock
* clk-xilinx:
clk: zynqmp: Add support for clock with CLK_DIVIDER_POWER_OF_TWO flag
clk: zynqmp: Fix divider calculation
clk: zynqmp: Add support for get max divider
clk: zynqmp: Warn user if clock user are more than allowed
clk: zynqmp: Extend driver for versal
dt-bindings: clock: Add bindings for versal clock driver
* clk-nvidia:
clk: tegra20/30: Explicitly set parent clock for Video Decoder
clk: tegra20/30: Don't pre-initialize displays parent clock
clk: tegra: divider: Check UART's divider enable-bit state on rate's recalculation
clk: tegra: clk-dfll: Remove call to pm_runtime_irq_safe()
clk: tegra: Mark fuse clock as critical
* clk-qcom: (35 commits)
clk: qcom: rpmh: Sort OF match table
dt-bindings: fix warnings in validation of qcom,gcc.yaml
dt-binding: fix compilation error of the example in qcom,gcc.yaml
clk: qcom: Add ipq6018 Global Clock Controller support
clk: qcom: Add DT bindings for ipq6018 gcc clock controller
clk: qcom: gcc-msm8996: Fix parent for CLKREF clocks
clk: qcom: rpmh: Add IPA clock for SC7180
clk: qcom: rpmh: skip undefined clocks when registering
clk: qcom: Add video clock controller driver for SC7180
dt-bindings: clock: Introduce SC7180 QCOM Video clock bindings
dt-bindings: clock: Add YAML schemas for the QCOM VIDEOCC clock bindings
clk: qcom: Add graphics clock controller driver for SC7180
dt-bindings: clock: Introduce SC7180 QCOM Graphics clock bindings
dt-bindings: clock: Add YAML schemas for the QCOM GPUCC clock bindings
clk: qcom: apcs-msm8916: use clk_parent_data to specify the parent
clk: qcom: Add display clock controller driver for SC7180
dt-bindings: clock: Introduce QCOM sc7180 display clock bindings
dt-bindings: clock: Add YAML schemas for the QCOM DISPCC clock bindings
clk: qcom: clk-alpha-pll: Add support for Fabia PLL calibration
clk: qcom: alpha-pll: Remove useless read from set rate
...
* clk-freescale:
clk: fsl-sai: new driver
dt-bindings: clock: document the fsl-sai driver
clk: composite: add _register_composite_pdata() variants
* clk-qoriq:
clk: qoriq: add ls1088a hwaccel clocks support
clk: ls1028a: Add clock driver for Display output interface
dt/bindings: clk: Add YAML schemas for LS1028A Display Clock bindings
|
|
'clk-amlogic' and 'clk-allwinner' into clk-next
- Support dangerous debugfs actions on clks with dead code
- Convert gpio, fixed-factor, mux, gate, divider basic clks to hw based APIs
* clk-debugfs-danger:
clk: Add support for setting clk_rate via debugfs
* clk-basic-hw:
clk: divider: Add support for specifying parents via DT/pointers
clk: gate: Add support for specifying parents via DT/pointers
clk: mux: Add support for specifying parents via DT/pointers
clk: asm9260: Use parent accuracy in fixed rate clk
clk: fixed-rate: Document that accuracy isn't a rate
clk: fixed-rate: Add clk flags for parent accuracy
clk: fixed-rate: Add support for specifying parents via DT/pointers
clk: fixed-rate: Document accuracy member
clk: fixed-rate: Move to_clk_fixed_rate() to C file
clk: fixed-rate: Remove clk_register_fixed_rate_with_accuracy()
clk: fixed-rate: Convert to clk_hw based APIs
clk: gpio: Use DT way of specifying parents
* clk-renesas:
clk: renesas: Prepare for split of R-Car H3 config symbol
dt-bindings: clock: renesas: cpg-mssr: Fix r8a774b1 typo
clk: renesas: r7s9210: Add SPIBSC clock
clk: renesas: rcar-gen3: Allow changing the RPC[D2] clocks
clk: renesas: Remove use of ARCH_R8A7796
clk: renesas: rcar-gen2: Change multipliers and dividers to u8
* clk-amlogic:
clk: clarify that clk_set_rate() does updates from top to bottom
clk: meson: meson8b: make the CCF use the glitch-free mali mux
clk: meson: pll: Fix by 0 division in __pll_params_to_rate()
clk: meson: g12a: fix missing uart2 in regmap table
clk: meson: meson8b: use of_clk_hw_register to register the clocks
clk: meson: meson8b: don't register the XTAL clock when provided via OF
clk: meson: meson8b: change references to the XTAL clock to use [fw_]name
clk: meson: meson8b: use clk_hw_set_parent in the CPU clock notifier
clk: meson: add a driver for the Meson8/8b/8m2 DDR clock controller
dt-bindings: clock: meson8b: add the clock inputs
dt-bindings: clock: add the Amlogic Meson8 DDR clock controller binding
* clk-allwinner:
clk: sunxi: a23/a33: Export the MIPI PLL
clk: sunxi: a31: Export the MIPI PLL
clk: sunxi-ng: a64: export CLK_CPUX clock for DVFS
clk: sunxi-ng: add mux and pll notifiers for A64 CPU clock
clk: sunxi-ng: r40: Export MBUS clock
clk: sunxi: use of_device_get_match_data
|
|
Pull iomap fix from Darrick Wong:
"A single patch fixing an off-by-one error when we're checking to see
how far we're gotten into an EOF page"
* tag 'iomap-5.6-merge-3' of git://git.kernel.org/pub/scm/fs/xfs/xfs-linux:
fs: Fix page_mkwrite off-by-one errors
|
|
Pull updates from Andrew Morton:
"Most of -mm and quite a number of other subsystems: hotfixes, scripts,
ocfs2, misc, lib, binfmt, init, reiserfs, exec, dma-mapping, kcov.
MM is fairly quiet this time. Holidays, I assume"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (118 commits)
kcov: ignore fault-inject and stacktrace
include/linux/io-mapping.h-mapping: use PHYS_PFN() macro in io_mapping_map_atomic_wc()
execve: warn if process starts with executable stack
reiserfs: prevent NULL pointer dereference in reiserfs_insert_item()
init/main.c: fix misleading "This architecture does not have kernel memory protection" message
init/main.c: fix quoted value handling in unknown_bootoption
init/main.c: remove unnecessary repair_env_string in do_initcall_level
init/main.c: log arguments and environment passed to init
fs/binfmt_elf.c: coredump: allow process with empty address space to coredump
fs/binfmt_elf.c: coredump: delete duplicated overflow check
fs/binfmt_elf.c: coredump: allocate core ELF header on stack
fs/binfmt_elf.c: make BAD_ADDR() unlikely
fs/binfmt_elf.c: better codegen around current->mm
fs/binfmt_elf.c: don't copy ELF header around
fs/binfmt_elf.c: fix ->start_code calculation
fs/binfmt_elf.c: smaller code generation around auxv vector fill
lib/find_bit.c: uninline helper _find_next_bit()
lib/find_bit.c: join _find_next_bit{_le}
uapi: rename ext2_swab() to swab() and share globally in swab.h
lib/scatterlist.c: adjust indentation in __sg_alloc_table
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jeyu/linux
Pull module updates from Jessica Yu:
"Summary of modules changes for the 5.6 merge window:
- Add "MS" (SHF_MERGE|SHF_STRINGS) section flags to __ksymtab_strings
to indicate to the linker that it can perform string deduplication
(i.e., duplicate strings are reduced to a single copy in the string
table). This means any repeated namespace string would be merged to
just one entry in __ksymtab_strings.
- Various code cleanups and small fixes (fix small memleak in error
path, improve moduleparam docs, silence rcu warnings, improve error
logging)"
* tag 'modules-for-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/jeyu/linux:
module.h: Annotate mod_kallsyms with __rcu
module: avoid setting info->name early in case we can fall back to info->mod->name
modsign: print module name along with error message
kernel/module: Fix memleak in module_add_modinfo_attrs()
export.h: reduce __ksymtab_strings string duplication by using "MS" section flags
moduleparam: fix kerneldoc
modules: lockdep: Suppress suspicious RCU usage warning
|
|
CONFIG_VIRTUALIZATION may not be enabled for memory encrypted guests. If
disabled, decrypted per-CPU variables may end up sharing the same page
with variables that should be left encrypted.
Always separate per-CPU variables that should be decrypted into their own
page anytime memory encryption can be enabled in the guest rather than
rely on any other config option that may not be enabled.
Fixes: ac26963a1175 ("percpu: Introduce DEFINE_PER_CPU_DECRYPTED")
Cc: stable@vger.kernel.org # 4.15+
Signed-off-by: Erdem Aktas <erdemaktas@google.com>
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Dennis Zhou <dennis@kernel.org>
|
|
The generic implementation of raw_cpu_generic_add_return() is:
#define raw_cpu_generic_add_return(pcp, val) \
({ \
typeof(&(pcp)) __p = raw_cpu_ptr(&(pcp)); \
\
*__p += val; \
*__p; \
})
where the 'pcp' argument is a __percpu lvalue.
There, the variable '__p' is declared as a __percpu pointer
the type of the address of 'pcp') but:
1) the value assigned to it, the return value of raw_cpu_ptr(), is
a plain (__kernel) pointer, not a __percpu one.
2) this variable is dereferenced just after while a __percpu
pointer is implicitly __noderef.
So, fix the declaration of the 'pcp' variable to its correct type:
the plain (non-percpu) pointer corresponding to pcp's address,
using the fact that typeof() ignores the address space and the
'noderef' attribute of its agument.
Same for raw_cpu_generic_xchg(), raw_cpu_generic_cmpxchg() &
raw_cpu_generic_cmpxchg_double().
This removes 209 warnings on ARM, 525 on ARM64, 220 on x86 &
more than 2600 on ppc64 (all of them with the default config).
Cc: Tejun Heo <tj@kernel.org>
Cc: Nicholas Piggin <npiggin@gmail.com>
Reported-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Luc Van Oostenryck <luc.vanoostenryck@gmail.com>
Acked-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Dennis Zhou <dennis@kernel.org>
|
|
io_mapping_map_atomic_wc()
Use PHYS_PFN() macro in io_mapping_map_atomic_wc() instead of open coded
variant.
Link: http://lkml.kernel.org/r/20191209165624.56351-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
ext2_swab() is defined locally in lib/find_bit.c However it is not
specific to ext2, neither to bitmaps.
There are many potential users of it, so rename it to just swab() and
move to include/uapi/linux/swab.h
ABI guarantees that size of unsigned long corresponds to BITS_PER_LONG,
therefore drop unneeded cast.
Link: http://lkml.kernel.org/r/20200103202846.21616-1-yury.norov@gmail.com
Signed-off-by: Yury Norov <yury.norov@gmail.com>
Cc: Allison Randal <allison@lohutok.net>
Cc: Joe Perches <joe@perches.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add a new function to zlib.h checking if s390 Deflate-Conversion
facility is installed and enabled.
Link: http://lkml.kernel.org/r/20200103223334.20669-6-zaslonko@linux.ibm.com
Signed-off-by: Mikhail Zaslonko <zaslonko@linux.ibm.com>
Cc: Chris Mason <clm@fb.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: David Sterba <dsterba@suse.com>
Cc: Eduard Shishkin <edward6@linux.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Ilya Leoshkevich <iii@linux.ibm.com>
Cc: Josef Bacik <josef@toxicpanda.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This removes the kelvin to/from Celsius conversion helper macros in
<linux/thermal.h> which were switched to the inline helper functions in
<linux/units.h>.
Link: http://lkml.kernel.org/r/1576386975-7941-9-git-send-email-akinobu.mita@gmail.com
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Sujith Thomas <sujith.thomas@intel.com>
Cc: Darren Hart <dvhart@infradead.org>
Cc: Andy Shevchenko <andy@infradead.org>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Amit Kucheria <amit.kucheria@verdurent.com>
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Keith Busch <kbusch@kernel.org>
Cc: Jens Axboe <axboe@fb.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Patch series "add header file for kelvin to/from Celsius conversion
helpers", v4.
There are several helper macros to convert kelvin to/from Celsius in
<linux/thermal.h> for thermal drivers. These are useful for any other
drivers or subsystems, but it's odd to include <linux/thermal.h> just
for the helpers.
This adds a new <linux/units.h> that provides the equivalent inline
functions for any drivers or subsystems, and switches all the users of
conversion helpers in <linux/thermal.h> to use <linux/units.h> helpers.
This patch (of 12):
There are several helper macros to convert kelvin to/from Celsius in
<linux/thermal.h> for thermal drivers. These are useful for any other
drivers or subsystems, but it's odd to include <linux/thermal.h> just
for the helpers.
This adds a new <linux/units.h> that provides the equivalent inline
functions for any drivers or subsystems. It is intended to replace the
helpers in <linux/thermal.h>.
Link: http://lkml.kernel.org/r/1576386975-7941-2-git-send-email-akinobu.mita@gmail.com
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Sujith Thomas <sujith.thomas@intel.com>
Cc: Darren Hart <dvhart@infradead.org>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Amit Kucheria <amit.kucheria@verdurent.com>
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Keith Busch <kbusch@kernel.org>
Cc: Jens Axboe <axboe@fb.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Stanislaw Gruszka <sgruszka@redhat.com>
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Andy Shevchenko <andy@infradead.org>
Cc: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
As zone reclaim has been replaced by node reclaim, this patch fixes
related comments.
Link: http://lkml.kernel.org/r/20191126141346.GA22665@haolee.github.io
Signed-off-by: Hao Lee <haolee.swjtu@gmail.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: Mel Gorman <mgorman@techsingularity.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
memory_block
memory_block structure elements 'hw' and 'phys_callback' are not getting
used. This was originally added with commit 3947be1969a9 ("[PATCH]
memory hotplug: sysfs and add/remove functions") but never seem to have
been used. Just drop them now.
Link: http://lkml.kernel.org/r/1576728650-13867-1-git-send-email-anshuman.khandual@arm.com
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Pavel Tatashin <pasha.tatashin@soleen.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
totalram_pages_set() was introduced in commit ca79b0c211af ("mm: convert
totalram_pages and totalhigh_pages variables to atomic"), but no one
uses it.
Link: http://lkml.kernel.org/r/20191218005543.24146-1-richardw.yang@linux.intel.com
Signed-off-by: Wei Yang <richardw.yang@linux.intel.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The check was intended to make sure we don't overrun page flags. But
it's obsolete because it doesn't include LAST_CPUPID_WIDTH nor
KASAN_TAG_WIDTH.
Just remove check since we already have it covered in
linux/page-flags-layout.h (near the end of the file).
Link: http://lkml.kernel.org/r/20191208183508.89177-1-yuzhao@google.com
Signed-off-by: Yu Zhao <yuzhao@google.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
It is not that hard to trigger lockdep splats by calling printk from
under zone->lock. Most of them are false positives caused by lock
chains introduced early in the boot process and they do not cause any
real problems (although most of the early boot lock dependencies could
happen after boot as well). There are some console drivers which do
allocate from the printk context as well and those should be fixed. In
any case, false positives are not that trivial to workaround and it is
far from optimal to lose lockdep functionality for something that is a
non-issue.
So change has_unmovable_pages() so that it no longer calls dump_page()
itself - instead it returns a "struct page *" of the unmovable page back
to the caller so that in the case of a has_unmovable_pages() failure,
the caller can call dump_page() after releasing zone->lock. Also, make
dump_page() is able to report a CMA page as well, so the reason string
from has_unmovable_pages() can be removed.
Even though has_unmovable_pages doesn't hold any reference to the
returned page this should be reasonably safe for the purpose of
reporting the page (dump_page) because it cannot be hotremoved in the
context of memory unplug. The state of the page might change but that
is the case even with the existing code as zone->lock only plays role
for free pages.
While at it, remove a similar but unnecessary debug-only printk() as
well. A sample of one of those lockdep splats is,
WARNING: possible circular locking dependency detected
------------------------------------------------------
test.sh/8653 is trying to acquire lock:
ffffffff865a4460 (console_owner){-.-.}, at:
console_unlock+0x207/0x750
but task is already holding lock:
ffff88883fff3c58 (&(&zone->lock)->rlock){-.-.}, at:
__offline_isolated_pages+0x179/0x3e0
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #3 (&(&zone->lock)->rlock){-.-.}:
__lock_acquire+0x5b3/0xb40
lock_acquire+0x126/0x280
_raw_spin_lock+0x2f/0x40
rmqueue_bulk.constprop.21+0xb6/0x1160
get_page_from_freelist+0x898/0x22c0
__alloc_pages_nodemask+0x2f3/0x1cd0
alloc_pages_current+0x9c/0x110
allocate_slab+0x4c6/0x19c0
new_slab+0x46/0x70
___slab_alloc+0x58b/0x960
__slab_alloc+0x43/0x70
__kmalloc+0x3ad/0x4b0
__tty_buffer_request_room+0x100/0x250
tty_insert_flip_string_fixed_flag+0x67/0x110
pty_write+0xa2/0xf0
n_tty_write+0x36b/0x7b0
tty_write+0x284/0x4c0
__vfs_write+0x50/0xa0
vfs_write+0x105/0x290
redirected_tty_write+0x6a/0xc0
do_iter_write+0x248/0x2a0
vfs_writev+0x106/0x1e0
do_writev+0xd4/0x180
__x64_sys_writev+0x45/0x50
do_syscall_64+0xcc/0x76c
entry_SYSCALL_64_after_hwframe+0x49/0xbe
-> #2 (&(&port->lock)->rlock){-.-.}:
__lock_acquire+0x5b3/0xb40
lock_acquire+0x126/0x280
_raw_spin_lock_irqsave+0x3a/0x50
tty_port_tty_get+0x20/0x60
tty_port_default_wakeup+0xf/0x30
tty_port_tty_wakeup+0x39/0x40
uart_write_wakeup+0x2a/0x40
serial8250_tx_chars+0x22e/0x440
serial8250_handle_irq.part.8+0x14a/0x170
serial8250_default_handle_irq+0x5c/0x90
serial8250_interrupt+0xa6/0x130
__handle_irq_event_percpu+0x78/0x4f0
handle_irq_event_percpu+0x70/0x100
handle_irq_event+0x5a/0x8b
handle_edge_irq+0x117/0x370
do_IRQ+0x9e/0x1e0
ret_from_intr+0x0/0x2a
cpuidle_enter_state+0x156/0x8e0
cpuidle_enter+0x41/0x70
call_cpuidle+0x5e/0x90
do_idle+0x333/0x370
cpu_startup_entry+0x1d/0x1f
start_secondary+0x290/0x330
secondary_startup_64+0xb6/0xc0
-> #1 (&port_lock_key){-.-.}:
__lock_acquire+0x5b3/0xb40
lock_acquire+0x126/0x280
_raw_spin_lock_irqsave+0x3a/0x50
serial8250_console_write+0x3e4/0x450
univ8250_console_write+0x4b/0x60
console_unlock+0x501/0x750
vprintk_emit+0x10d/0x340
vprintk_default+0x1f/0x30
vprintk_func+0x44/0xd4
printk+0x9f/0xc5
-> #0 (console_owner){-.-.}:
check_prev_add+0x107/0xea0
validate_chain+0x8fc/0x1200
__lock_acquire+0x5b3/0xb40
lock_acquire+0x126/0x280
console_unlock+0x269/0x750
vprintk_emit+0x10d/0x340
vprintk_default+0x1f/0x30
vprintk_func+0x44/0xd4
printk+0x9f/0xc5
__offline_isolated_pages.cold.52+0x2f/0x30a
offline_isolated_pages_cb+0x17/0x30
walk_system_ram_range+0xda/0x160
__offline_pages+0x79c/0xa10
offline_pages+0x11/0x20
memory_subsys_offline+0x7e/0xc0
device_offline+0xd5/0x110
state_store+0xc6/0xe0
dev_attr_store+0x3f/0x60
sysfs_kf_write+0x89/0xb0
kernfs_fop_write+0x188/0x240
__vfs_write+0x50/0xa0
vfs_write+0x105/0x290
ksys_write+0xc6/0x160
__x64_sys_write+0x43/0x50
do_syscall_64+0xcc/0x76c
entry_SYSCALL_64_after_hwframe+0x49/0xbe
other info that might help us debug this:
Chain exists of:
console_owner --> &(&port->lock)->rlock --> &(&zone->lock)->rlock
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&(&zone->lock)->rlock);
lock(&(&port->lock)->rlock);
lock(&(&zone->lock)->rlock);
lock(console_owner);
*** DEADLOCK ***
9 locks held by test.sh/8653:
#0: ffff88839ba7d408 (sb_writers#4){.+.+}, at:
vfs_write+0x25f/0x290
#1: ffff888277618880 (&of->mutex){+.+.}, at:
kernfs_fop_write+0x128/0x240
#2: ffff8898131fc218 (kn->count#115){.+.+}, at:
kernfs_fop_write+0x138/0x240
#3: ffffffff86962a80 (device_hotplug_lock){+.+.}, at:
lock_device_hotplug_sysfs+0x16/0x50
#4: ffff8884374f4990 (&dev->mutex){....}, at:
device_offline+0x70/0x110
#5: ffffffff86515250 (cpu_hotplug_lock.rw_sem){++++}, at:
__offline_pages+0xbf/0xa10
#6: ffffffff867405f0 (mem_hotplug_lock.rw_sem){++++}, at:
percpu_down_write+0x87/0x2f0
#7: ffff88883fff3c58 (&(&zone->lock)->rlock){-.-.}, at:
__offline_isolated_pages+0x179/0x3e0
#8: ffffffff865a4920 (console_lock){+.+.}, at:
vprintk_emit+0x100/0x340
stack backtrace:
Hardware name: HPE ProLiant DL560 Gen10/ProLiant DL560 Gen10,
BIOS U34 05/21/2019
Call Trace:
dump_stack+0x86/0xca
print_circular_bug.cold.31+0x243/0x26e
check_noncircular+0x29e/0x2e0
check_prev_add+0x107/0xea0
validate_chain+0x8fc/0x1200
__lock_acquire+0x5b3/0xb40
lock_acquire+0x126/0x280
console_unlock+0x269/0x750
vprintk_emit+0x10d/0x340
vprintk_default+0x1f/0x30
vprintk_func+0x44/0xd4
printk+0x9f/0xc5
__offline_isolated_pages.cold.52+0x2f/0x30a
offline_isolated_pages_cb+0x17/0x30
walk_system_ram_range+0xda/0x160
__offline_pages+0x79c/0xa10
offline_pages+0x11/0x20
memory_subsys_offline+0x7e/0xc0
device_offline+0xd5/0x110
state_store+0xc6/0xe0
dev_attr_store+0x3f/0x60
sysfs_kf_write+0x89/0xb0
kernfs_fop_write+0x188/0x240
__vfs_write+0x50/0xa0
vfs_write+0x105/0x290
ksys_write+0xc6/0x160
__x64_sys_write+0x43/0x50
do_syscall_64+0xcc/0x76c
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Link: http://lkml.kernel.org/r/20200117181200.20299-1-cai@lca.pw
Signed-off-by: Qian Cai <cai@lca.pw>
Reviewed-by: David Hildenbrand <david@redhat.com>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com>
Cc: Petr Mladek <pmladek@suse.com>
Cc: Steven Rostedt (VMware) <rostedt@goodmis.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Patch series "mm/memory_hotplug: pass in nid to online_pages()".
Simplify onlining code and get rid of find_memory_block(). Pass in the
nid from the memory block we are trying to online directly, instead of
manually looking it up.
This patch (of 2):
No need to lookup the memory block, we can directly pass in the nid.
Link: http://lkml.kernel.org/r/20200113113354.6341-2-david@redhat.com
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Oscar Salvador <osalvador@suse.de>
Cc: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Pavel Tatashin <pasha.tatashin@soleen.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
On the s390 platform memblock.physmem array is being built by directly
calling into memblock_add_range() which is a low level function not
intended to be used outside of memblock. Hence lets conditionally add
helper functions for physmem array when HAVE_MEMBLOCK_PHYS_MAP is
enabled. Also use MAX_NUMNODES instead of 0 as node ID similar to
memblock_add() and memblock_reserve(). Make memblock_add_range() a
static function as it is no longer getting used outside of memblock.
Link: http://lkml.kernel.org/r/1578283835-21969-1-git-send-email-anshuman.khandual@arm.com
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Reviewed-by: Mike Rapoport <rppt@linux.ibm.com>
Acked-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Collin Walling <walling@linux.ibm.com>
Cc: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Cc: Philipp Rudo <prudo@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Now that the memory isolate notifier is gone, the parameter is always 0.
Drop it and cleanup has_unmovable_pages().
Link: http://lkml.kernel.org/r/20191114131911.11783-3-david@redhat.com
Signed-off-by: David Hildenbrand <david@redhat.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Oscar Salvador <osalvador@suse.de>
Cc: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: Qian Cai <cai@lca.pw>
Cc: Pingfan Liu <kernelfans@gmail.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Pavel Tatashin <pasha.tatashin@soleen.com>
Cc: Vlastimil Babka <vbabka@suse.cz>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: Wei Yang <richardw.yang@linux.intel.com>
Cc: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Cc: Alexander Potapenko <glider@google.com>
Cc: Arun KS <arunks@codeaurora.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Luckily, we have no users left, so we can get rid of it. Cleanup
set_migratetype_isolate() a little bit.
Link: http://lkml.kernel.org/r/20191114131911.11783-2-david@redhat.com
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: Pavel Tatashin <pasha.tatashin@soleen.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Oscar Salvador <osalvador@suse.de>
Cc: Qian Cai <cai@lca.pw>
Cc: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: Pingfan Liu <kernelfans@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Print the call_site ip of kmem_alloc_node using '%pS' to improve the
readability of raw slab trace points.
Link: http://lkml.kernel.org/r/1577949568-4518-1-git-send-email-sunjunyong@xiaomi.com
Signed-off-by: Junyong Sun <sunjunyong@xiaomi.com>
Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Joel Fernandes (Google) <joel@joelfernandes.org>
Cc: Changbin Du <changbin.du@intel.com>
Cc: Tim Murray <timmurray@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
In order to provide a clearer, more symmetric API for pinning and
unpinning DMA pages. This way, pin_user_pages*() calls match up with
unpin_user_pages*() calls, and the API is a lot closer to being
self-explanatory.
Link: http://lkml.kernel.org/r/20200107224558.2362728-23-jhubbard@nvidia.com
Signed-off-by: John Hubbard <jhubbard@nvidia.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Cc: Björn Töpel <bjorn.topel@intel.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: Ira Weiny <ira.weiny@intel.com>
Cc: Jason Gunthorpe <jgg@mellanox.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Kirill A. Shutemov <kirill@shutemov.name>
Cc: Leon Romanovsky <leonro@mellanox.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Introduce pin_user_pages*() variations of get_user_pages*() calls, and
also pin_longterm_pages*() variations.
For now, these are placeholder calls, until the various call sites are
converted to use the correct get_user_pages*() or pin_user_pages*() API.
These variants will eventually all set FOLL_PIN, which is also
introduced, and thoroughly documented.
pin_user_pages()
pin_user_pages_remote()
pin_user_pages_fast()
All pages that are pinned via the above calls, must be unpinned via
put_user_page().
The underlying rules are:
* FOLL_PIN is a gup-internal flag, so the call sites should not directly
set it. That behavior is enforced with assertions.
* Call sites that want to indicate that they are going to do DirectIO
("DIO") or something with similar characteristics, should call a
get_user_pages()-like wrapper call that sets FOLL_PIN. These wrappers
will:
* Start with "pin_user_pages" instead of "get_user_pages". That
makes it easy to find and audit the call sites.
* Set FOLL_PIN
* For pages that are received via FOLL_PIN, those pages must be returned
via put_user_page().
Thanks to Jan Kara and Vlastimil Babka for explaining the 4 cases in
this documentation. (I've reworded it and expanded upon it.)
Link: http://lkml.kernel.org/r/20200107224558.2362728-12-jhubbard@nvidia.com
Signed-off-by: John Hubbard <jhubbard@nvidia.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Reviewed-by: Mike Rapoport <rppt@linux.ibm.com> [Documentation]
Reviewed-by: Jérôme Glisse <jglisse@redhat.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Ira Weiny <ira.weiny@intel.com>
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Cc: Björn Töpel <bjorn.topel@intel.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: Jason Gunthorpe <jgg@mellanox.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Kirill A. Shutemov <kirill@shutemov.name>
Cc: Leon Romanovsky <leonro@mellanox.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
An upcoming patch changes and complicates the refcounting and especially
the "put page" aspects of it. In order to keep everything clean,
refactor the devmap page release routines:
* Rename put_devmap_managed_page() to page_is_devmap_managed(), and
limit the functionality to "read only": return a bool, with no side
effects.
* Add a new routine, put_devmap_managed_page(), to handle decrementing
the refcount for ZONE_DEVICE pages.
* Change callers (just release_pages() and put_page()) to check
page_is_devmap_managed() before calling the new
put_devmap_managed_page() routine. This is a performance point:
put_page() is a hot path, so we need to avoid non- inline function calls
where possible.
* Rename __put_devmap_managed_page() to free_devmap_managed_page(), and
limit the functionality to unconditionally freeing a devmap page.
This is originally based on a separate patch by Ira Weiny, which applied
to an early version of the put_user_page() experiments. Since then,
Jérôme Glisse suggested the refactoring described above.
Link: http://lkml.kernel.org/r/20200107224558.2362728-5-jhubbard@nvidia.com
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: John Hubbard <jhubbard@nvidia.com>
Suggested-by: Jérôme Glisse <jglisse@redhat.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Kirill A. Shutemov <kirill@shutemov.name>
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Cc: Björn Töpel <bjorn.topel@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Cc: Jason Gunthorpe <jgg@mellanox.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Leon Romanovsky <leonro@mellanox.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
At some point filemap_write_and_wait() and
filemap_write_and_wait_range() got the exact same implementation with
the exception of the range being specified in *_range()
Similar to other functions in fs.h which call *_range(..., 0,
LLONG_MAX), change filemap_write_and_wait() to be a static inline which
calls filemap_write_and_wait_range()
Link: http://lkml.kernel.org/r/20191129160713.30892-1-ira.weiny@intel.com
Signed-off-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
There are users already and will be more of BITS_TO_BYTES() macro. Move
it to bitops.h for wider use.
In the case of ocfs2 the replacement is identical.
As for bnx2x, there are two places where floor version is used. In the
first case to calculate the amount of structures that can fit one memory
page. In this case obviously the ceiling variant is correct and
original code might have a potential bug, if amount of bits % 8 is not
0. In the second case the macro is used to calculate bytes transmitted
in one microsecond. This will work for all speeds which is multiply of
1Gbps without any change, for the rest new code will give ceiling value,
for instance 100Mbps will give 13 bytes, while old code gives 12 bytes
and the arithmetically correct one is 12.5 bytes. Further the value is
used to setup timer threshold which in any case has its own margins due
to certain resolution. I don't see here an issue with slightly shifting
thresholds for low speed connections, the card is supposed to utilize
highest available rate, which is usually 10Gbps.
Link: http://lkml.kernel.org/r/20200108121316.22411-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Joseph Qi <joseph.qi@linux.alibaba.com>
Acked-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Cc: Mark Fasheh <mark@fasheh.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Changwei Ge <gechangwei@live.cn>
Cc: Gang He <ghe@suse.com>
Cc: Jun Piao <piaojun@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Without memcg, there is a one-to-one mapping between the bdi and
bdi_writeback structures. In this world, things are fairly
straightforward; the first thing bdi_unregister() does is to shutdown
the bdi_writeback structure (or wb), and part of that writeback ensures
that no other work queued against the wb, and that the wb is fully
drained.
With memcg, however, there is a one-to-many relationship between the bdi
and bdi_writeback structures; that is, there are multiple wb objects
which can all point to a single bdi. There is a refcount which prevents
the bdi object from being released (and hence, unregistered). So in
theory, the bdi_unregister() *should* only get called once its refcount
goes to zero (bdi_put will drop the refcount, and when it is zero,
release_bdi gets called, which calls bdi_unregister).
Unfortunately, del_gendisk() in block/gen_hd.c never got the memo about
the Brave New memcg World, and calls bdi_unregister directly. It does
this without informing the file system, or the memcg code, or anything
else. This causes the root wb associated with the bdi to be
unregistered, but none of the memcg-specific wb's are shutdown. So when
one of these wb's are woken up to do delayed work, they try to
dereference their wb->bdi->dev to fetch the device name, but
unfortunately bdi->dev is now NULL, thanks to the bdi_unregister()
called by del_gendisk(). As a result, *boom*.
Fortunately, it looks like the rest of the writeback path is perfectly
happy with bdi->dev and bdi->owner being NULL, so the simplest fix is to
create a bdi_dev_name() function which can handle bdi->dev being NULL.
This also allows us to bulletproof the writeback tracepoints to prevent
them from dereferencing a NULL pointer and crashing the kernel if one is
tracing with memcg's enabled, and an iSCSI device dies or a USB storage
stick is pulled.
The most common way of triggering this will be hotremoval of a device
while writeback with memcg enabled is going on. It was triggering
several times a day in a heavily loaded production environment.
Google Bug Id: 145475544
Link: https://lore.kernel.org/r/20191227194829.150110-1-tytso@mit.edu
Link: http://lkml.kernel.org/r/20191228005211.163952-1-tytso@mit.edu
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: Chris Mason <clm@fb.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
As of the patch ("MIPS: kdb: Remove old workaround for backtracing on
other CPUs") there is no reason for kdb_current_regs to be in the
public "kdb.h". Let's move it next to kdb_current_task.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20191109111623.2.Iadbfb484e90b557cc4b5ac9890bfca732cd99d77@changeid
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
|
|
Pull KVM updates from Paolo Bonzini:
"This is the first batch of KVM changes.
ARM:
- cleanups and corner case fixes.
PPC:
- Bugfixes
x86:
- Support for mapping DAX areas with large nested page table entries.
- Cleanups and bugfixes here too. A particularly important one is a
fix for FPU load when the thread has TIF_NEED_FPU_LOAD. There is
also a race condition which could be used in guest userspace to
exploit the guest kernel, for which the embargo expired today.
- Fast path for IPI delivery vmexits, shaving about 200 clock cycles
from IPI latency.
- Protect against "Spectre-v1/L1TF" (bring data in the cache via
speculative out of bound accesses, use L1TF on the sibling
hyperthread to read it), which unfortunately is an even bigger
whack-a-mole game than SpectreV1.
Sean continues his mission to rewrite KVM. In addition to a sizable
number of x86 patches, this time he contributed a pretty large
refactoring of vCPU creation that affects all architectures but should
not have any visible effect.
s390 will come next week together with some more x86 patches"
* tag 'kvm-5.6-1' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (204 commits)
x86/KVM: Clean up host's steal time structure
x86/KVM: Make sure KVM_VCPU_FLUSH_TLB flag is not missed
x86/kvm: Cache gfn to pfn translation
x86/kvm: Introduce kvm_(un)map_gfn()
x86/kvm: Be careful not to clear KVM_VCPU_FLUSH_TLB bit
KVM: PPC: Book3S PR: Fix -Werror=return-type build failure
KVM: PPC: Book3S HV: Release lock on page-out failure path
KVM: arm64: Treat emulated TVAL TimerValue as a signed 32-bit integer
KVM: arm64: pmu: Only handle supported event counters
KVM: arm64: pmu: Fix chained SW_INCR counters
KVM: arm64: pmu: Don't mark a counter as chained if the odd one is disabled
KVM: arm64: pmu: Don't increment SW_INCR if PMCR.E is unset
KVM: x86: Use a typedef for fastop functions
KVM: X86: Add 'else' to unify fastop and execute call path
KVM: x86: inline memslot_valid_for_gpte
KVM: x86/mmu: Use huge pages for DAX-backed files
KVM: x86/mmu: Remove lpage_is_disallowed() check from set_spte()
KVM: x86/mmu: Fold max_mapping_level() into kvm_mmu_hugepage_adjust()
KVM: x86/mmu: Zap any compound page when collapsing sptes
KVM: x86/mmu: Remove obsolete gfn restoration in FNAME(fetch)
...
|
|
Since we have a bitwise definition of snd_pcm_state_t and use it for
certain struct fields, a few new (and years old) sparse warnings came
up. This patch is an attempt to cover them.
- The state fields in snd_pcm_mmap_status* and co are all defined as
snd_pcm_state_t type now
- The PCM action callbacks take snd_pcm_state_t argument as well;
some actions taking special values got the explicit cast and
comments
- For the PCM action that doesn't need an extra argument receives
ACTION_ARG_IGNORE instead of ambiguous 0
While we're at it, the boolean argument is also properly changed to
bool and true/false, as well as a slight refactoring of PCM pause
helper function to make easier to read.
No functional changes, just shutting up chatty sparse.
Fixes: 46b770f720bd ("ALSA: uapi: Fix sparse warning")
Reported-by: kbuild test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/20200131152214.11698-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The architecture states that we need to reset local IRQs for all CPU
resets. Because the old reset interface did not support the normal CPU
reset we never did that on a normal reset.
Let's implement an interface for the missing normal and clear resets
and reset all local IRQs, registers and control structures as stated
in the architecture.
Userspace might already reset the registers via the vcpu run struct,
but as we need the interface for the interrupt clearing part anyway,
we implement the resets fully and don't rely on userspace to reset the
rest.
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Link: https://lore.kernel.org/r/20200131100205.74720-4-frankja@linux.ibm.com
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
|
|
* pm-cpufreq:
cpufreq: Avoid creating excessively large stack frames
* pm-core:
PM: core: Fix handling of devices deleted during system-wide resume
|
|
into drm-next
A small fix for the long-standing ttm vm page protection hack.
Sent as a separate PR as it touches mm, has all acks in place.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thomas Hellström (VMware) <thellstrom@vmware.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200116102411.3056-1-thomas_os@shipmail.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/daveh/x86-mpx
Pull x86 MPX removal from Dave Hansen:
"MPX requires recompiling applications, which requires compiler
support. Unfortunately, GCC 9.1 is expected to be be released without
support for MPX. This means that there was only a relatively small
window where folks could have ever used MPX. It failed to gain wide
adoption in the industry, and Linux was the only mainstream OS to ever
support it widely.
Support for the feature may also disappear on future processors.
This set completes the process that we started during the 5.4 merge
window when the MPX prctl()s were removed. XSAVE support is left in
place, which allows MPX-using KVM guests to continue to function"
* tag 'mpx-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/daveh/x86-mpx:
x86/mpx: remove MPX from arch/x86
mm: remove arch_bprm_mm_init() hook
x86/mpx: remove bounds exception code
x86/mpx: remove build infrastructure
x86/alternatives: add missing insn.h include
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Miquel Raynal:
"MTD core
- block2mtd: page index should use pgoff_t
- maps: physmap: minimal Runtime PM support
- maps: pcmciamtd: avoid possible sleep-in-atomic-context bugs
- concat: Fix a comment referring to an unknown symbol
Raw NAND:
- Macronix: Use match_string() helper
- Atmel: switch to using devm_fwnode_gpiod_get()
- Denali: rework the SKIP_BYTES feature and add reset controlling
- Brcmnand: set appropriate DMA mask
- Cadence: add unspecified HAS_IOMEM dependency
- Various cleanup.
Onenand:
- Rename Samsung and Omap2 drivers to avoid possible build warnings
- Enable compile testing
- Various build issues
- Kconfig cleanup
SPI-NAND:
- Support for Toshiba TC58CVG2S0HRAIJ
SPI-NOR:
- Add support for TB selection using SR bit 6,
- Add support for few flashes"
* tag 'mtd/for-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (41 commits)
mtd: concat: Fix a comment referring to an unknown symbol
mtd: rawnand: add unspecified HAS_IOMEM dependency
mtd: block2mtd: page index should use pgoff_t
mtd: maps: physmap: Add minimal Runtime PM support
mtd: maps: pcmciamtd: fix possible sleep-in-atomic-context bugs in pcmciamtd_set_vpp()
mtd: onenand: Rename omap2 driver to avoid a build warning
mtd: onenand: Use a better name for samsung driver
mtd: rawnand: atmel: switch to using devm_fwnode_gpiod_get()
mtd: spinand: add support for Toshiba TC58CVG2S0HRAIJ
mtd: rawnand: macronix: Use match_string() helper to simplify the code
mtd: sharpslpart: Fix unsigned comparison to zero
mtd: onenand: Enable compile testing of OMAP and Samsung drivers
mtd: onenand: samsung: Fix printing format for size_t on 64-bit
mtd: onenand: samsung: Fix pointer cast -Wpointer-to-int-cast warnings on 64 bit
mtd: rawnand: denali: remove hard-coded DENALI_DEFAULT_OOB_SKIP_BYTES
mtd: rawnand: denali_dt: add reset controlling
dt-bindings: mtd: denali_dt: document reset property
mtd: rawnand: denali_dt: Add support for configuring SPARE_AREA_SKIP_BYTES
mtd: rawnand: denali_dt: error out if platform has no associated data
mtd: rawnand: brcmnand: Set appropriate DMA mask
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs
Pull f2fs updates from Jaegeuk Kim:
"In this series, we've implemented transparent compression
experimentally. It supports LZO and LZ4, but will add more later as we
investigate in the field more.
At this point, the feature doesn't expose compressed space to user
directly in order to guarantee potential data updates later to the
space. Instead, the main goal is to reduce data writes to flash disk
as much as possible, resulting in extending disk life time as well as
relaxing IO congestion.
Alternatively, we're also considering to add ioctl() to reclaim
compressed space and show it to user after putting the immutable bit.
Enhancements:
- add compression support
- avoid unnecessary locks in quota ops
- harden power-cut scenario for zoned block devices
- use private bio_set to avoid IO congestion
- replace GC mutex with rwsem to serialize callers
Bug fixes:
- fix dentry consistency and memory corruption in rename()'s error case
- fix wrong swap extent reports
- fix casefolding bugs
- change lock coverage to avoid deadlock
- avoid GFP_KERNEL under f2fs_lock_op
And, we've cleaned up sysfs entries to prepare no debugfs"
* tag 'f2fs-for-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/jaegeuk/f2fs: (31 commits)
f2fs: fix race conditions in ->d_compare() and ->d_hash()
f2fs: fix dcache lookup of !casefolded directories
f2fs: Add f2fs stats to sysfs
f2fs: delete duplicate information on sysfs nodes
f2fs: change to use rwsem for gc_mutex
f2fs: update f2fs document regarding to fsync_mode
f2fs: add a way to turn off ipu bio cache
f2fs: code cleanup for f2fs_statfs_project()
f2fs: fix miscounted block limit in f2fs_statfs_project()
f2fs: show the CP_PAUSE reason in checkpoint traces
f2fs: fix deadlock allocating bio_post_read_ctx from mempool
f2fs: remove unneeded check for error allocating bio_post_read_ctx
f2fs: convert inline_dir early before starting rename
f2fs: fix memleak of kobject
f2fs: fix to add swap extent correctly
f2fs: run fsck when getting bad inode during GC
f2fs: support data compression
f2fs: free sysfs kobject
f2fs: declare nested quota_sem and remove unnecessary sems
f2fs: don't put new_page twice in f2fs_rename
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull ext4 updates from Ted Ts'o:
"This merge window, we've added some performance improvements in how we
handle inode locking in the read/write paths, and improving the
performance of Direct I/O overwrites.
We also now record the error code which caused the first and most
recent ext4_error() report in the superblock, to make it easier to
root cause problems in production systems.
There are also many of the usual cleanups and miscellaneous bug fixes"
* tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4: (49 commits)
jbd2: clean __jbd2_journal_abort_hard() and __journal_abort_soft()
jbd2: make sure ESHUTDOWN to be recorded in the journal superblock
ext4, jbd2: ensure panic when aborting with zero errno
jbd2: switch to use jbd2_journal_abort() when failed to submit the commit record
jbd2_seq_info_next should increase position index
jbd2: remove pointless assertion in __journal_remove_journal_head
ext4,jbd2: fix comment and code style
jbd2: delete the duplicated words in the comments
ext4: fix extent_status trace points
ext4: fix symbolic enum printing in trace output
ext4: choose hardlimit when softlimit is larger than hardlimit in ext4_statfs_project()
ext4: fix race conditions in ->d_compare() and ->d_hash()
ext4: make dioread_nolock the default
ext4: fix extent_status fragmentation for plain files
jbd2: clear JBD2_ABORT flag before journal_reset to update log tail info when load journal
ext4: drop ext4_kvmalloc()
ext4: Add EXT4_IOC_FSGETXATTR/EXT4_IOC_FSSETXATTR to compat_ioctl
ext4: remove unused macro MPAGE_DA_EXTENT_TAIL
ext4: add missing braces in ext4_ext_drop_refs()
ext4: fix some nonstandard indentation in extents.c
...
|
|
Compilation of mlx5 driver without CONFIG_INFINIBAND_USER_ACCESS generates
the following error.
on x86_64:
ld: drivers/infiniband/hw/mlx5/main.o: in function `mlx5_ib_handler_MLX5_IB_METHOD_VAR_OBJ_ALLOC':
main.c:(.text+0x186d): undefined reference to `ib_uverbs_get_ucontext_file'
ld: drivers/infiniband/hw/mlx5/main.o:(.rodata+0x2480): undefined reference to `uverbs_idr_class'
ld: drivers/infiniband/hw/mlx5/main.o:(.rodata+0x24d8): undefined reference to `uverbs_destroy_def_handler'
This is happening because some parts of the UAPI description are not
static. This is a hold over from earlier code that relied on struct
pointers to refer to object types, now object types are referenced by
number. Remove the unused globals and add statics to the remaining UAPI
description elements.
Remove the redundent #ifdefs around mlx5_ib_*defs and obsolete
mlx5_ib_get_devx_tree().
The compiler now trims alot more unused code, including the above
problematic definitions when !CONFIG_INFINIBAND_USER_ACCESS.
Fixes: 7be76bef320b ("IB/mlx5: Introduce VAR object and its alloc/destroy methods")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|