| Age | Commit message (Collapse) | Author |
|---|
|
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
|
|
ELM module can be used for hardware error correction of BCH 4 & 8 bit.
ELM module functionality is verified by checking the availability of
handle for ELM module in device tree. Hence supporting
1. ELM module available, BCH error correction done by ELM module. Also
support read & write page in one shot by adding custom read_page and
write_page methods. This helps in optimizing code for NAND flashes with
page size less than 4 KB.
2. If ELM module not available fall back to software BCH error
correction support.
New structure member is added to omap_nand_info
1. "is_elm_used" to know the status of whether the ELM module is used for
error correction or not.
2. "elm_dev" device pointer to elm device on detection of ELM module.
Also being here update the device tree documentation of gpmc-nand for
adding optional property elm_id.
Note:
ECC layout uses 1 extra bytes for 512 byte of data to handle erased
pages. Extra byte programmed to zero for programmed pages. Also BCH8
requires 14 byte ecc to maintain compatibility with RBL ECC layout.
This results a common ecc layout across RBL, U-boot & Linux with BCH8.
Signed-off-by: Philip Avinash <avinashphilip@ti.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
|
|
The ELM hardware module can be used to speedup BCH 4/8/16 ECC scheme
error correction.
For now only 4 & 8 bit support is added
Signed-off-by: Philip Avinash <avinashphilip@ti.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Peter Anvin:
"This is a collection of miscellaneous fixes, the most important one is
the fix for the Samsung laptop bricking issue (auto-blacklisting the
samsung-laptop driver); the efi_enabled() changes you see below are
prerequisites for that fix.
The other issues fixed are booting on OLPC XO-1.5, an UV fix, NMI
debugging, and requiring CAP_SYS_RAWIO for MSR references, just as
with I/O port references."
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
samsung-laptop: Disable on EFI hardware
efi: Make 'efi_enabled' a function to query EFI facilities
smp: Fix SMP function call empty cpu mask race
x86/msr: Add capabilities check
x86/dma-debug: Bump PREALLOC_DMA_DEBUG_ENTRIES
x86/olpc: Fix olpc-xo1-sci.c build errors
arch/x86/platform/uv: Fix incorrect tlb flush all issue
x86-64: Fix unwind annotations in recent NMI changes
x86-32: Start out cr0 clean, disable paging before modifying cr3/4
|
|
Originally 'efi_enabled' indicated whether a kernel was booted from
EFI firmware. Over time its semantics have changed, and it now
indicates whether or not we are booted on an EFI machine with
bit-native firmware, e.g. 64-bit kernel with 64-bit firmware.
The immediate motivation for this patch is the bug report at,
https://bugs.launchpad.net/ubuntu-cdimage/+bug/1040557
which details how running a platform driver on an EFI machine that is
designed to run under BIOS can cause the machine to become
bricked. Also, the following report,
https://bugzilla.kernel.org/show_bug.cgi?id=47121
details how running said driver can also cause Machine Check
Exceptions. Drivers need a new means of detecting whether they're
running on an EFI machine, as sadly the expression,
if (!efi_enabled)
hasn't been a sufficient condition for quite some time.
Users actually want to query 'efi_enabled' for different reasons -
what they really want access to is the list of available EFI
facilities.
For instance, the x86 reboot code needs to know whether it can invoke
the ResetSystem() function provided by the EFI runtime services, while
the ACPI OSL code wants to know whether the EFI config tables were
mapped successfully. There are also checks in some of the platform
driver code to simply see if they're running on an EFI machine (which
would make it a bad idea to do BIOS-y things).
This patch is a prereq for the samsung-laptop fix patch.
Cc: David Airlie <airlied@linux.ie>
Cc: Corentin Chary <corentincj@iksaif.net>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Peter Jones <pjones@redhat.com>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: Steve Langasek <steve.langasek@canonical.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Konrad Rzeszutek Wilk <konrad@kernel.org>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: <stable@vger.kernel.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull MFD fixes from Samuel Ortiz:
"This is the first pull request for MFD fixes for 3.8
We have some build failure fixes (twl4030, vexpress, abx500 and
tps65910), some actual runtime oops and lockup fixes (rtsx, da9052),
and some more hypothetical NULL pointers dereferences fixes for
pcf50633 and max776xx.
Then we also have additional rtsx fixes for a correct switch output
voltage and clock divider correctness for rtl8411 (rtsx driver), and
irqdomain fix for db8550-prcmu, and some more cosmetic fixes for
arizona and wm5102."
* tag 'mfd-for-linus-3.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6:
mfd: rtsx: Fix oops when rtsx_pci_sdmmc is not probed
mfd: wm5102: Fix definition of WM5102_MAX_REGISTER
mfd: twl4030: Don't warn about uninitialized return code
mfd: da9052/53 lockup fix
mfd: rtsx: Add clock divider hook
mmc: rtsx: Call MFD hook to switch output voltage
mfd: rtsx: Add output voltage switch hook
mfd: Fix compile errors and warnings when !CONFIG_AB8500_BM
mfd: vexpress: Export global functions to fix build error
mfd: arizona: Check errors from regcache_sync()
mfd: tc3589x: Use simple irqdomain
mfd: pcf50633: Init pcf->dev before using it
mfd: max77693: Init max77693->dev before using it
mfd: max77686: Init max77686->dev before using it
mfd: db8500-prcmu: Fix irqdomain usage
mfd: tps65910: Select REGMAP_IRQ in Kconfig to fix build error
mfd: arizona: Disable control interface reporting for WM5102 and WM5110
|
|
Pull networking updates from David Miller:
"Much more accumulated than I would have liked due to an unexpected
bout with a nasty flu:
1) AH and ESP input don't set ECN field correctly because the
transport head of the SKB isn't set correctly, fix from Li
RongQing.
2) If netfilter conntrack zones are disabled, we can return an
uninitialized variable instead of the proper error code. Fix from
Borislav Petkov.
3) Fix double SKB free in ath9k driver beacon handling, from Felix
Feitkau.
4) Remove bogus assumption about netns cleanup ordering in
nf_conntrack, from Pablo Neira Ayuso.
5) Remove a bogus BUG_ON in the new TCP fastopen code, from Eric
Dumazet. It uses spin_is_locked() in it's test and is therefore
unsuitable for UP.
6) Fix SELINUX labelling regressions added by the tuntap multiqueue
changes, from Paul Moore.
7) Fix CRC errors with jumbo frame receive in tg3 driver, from Nithin
Nayak Sujir.
8) CXGB4 driver sets interrupt coalescing parameters only on first
queue, rather than all of them. Fix from Thadeu Lima de Souza
Cascardo.
9) Fix regression in the dispatch of read/write registers in dm9601
driver, from Tushar Behera.
10) ipv6_append_data miscalculates header length, from Romain KUNTZ.
11) Fix PMTU handling regressions on ipv4 routes, from Steffen
Klassert, Timo Teräs, and Julian Anastasov.
12) In 3c574_cs driver, add necessary parenthesis to "x << y & z"
expression. From Nickolai Zeldovich.
13) macvlan_get_size() causes underallocation netlink message space,
fix from Eric Dumazet.
14) Avoid division by zero in xfrm_replay_advance_bmp(), from Nickolai
Zeldovich. Amusingly the zero check was already there, we were
just performing it after the modulus :-)
15) Some more splice bug fixes from Eric Dumazet, which fix things
mostly eminating from how we now more aggressively use high-order
pages in SKBs.
16) Fix size calculation bug when freeing hash tables in the IPSEC
xfrm code, from Michal Kubecek.
17) Fix PMTU event propagation into socket cached routes, from Steffen
Klassert.
18) Fix off by one in TX buffer release in netxen driver, from Eric
Dumazet.
19) Fix rediculous memory allocation requirements introduced by the
tuntap multiqueue changes, from Jason Wang.
20) Remove bogus AMD platform workaround in r8169 driver that causes
major problems in normal operation, from Timo Teräs.
21) virtio-net set affinity and select queue don't handle
discontiguous cpu numbers properly, fix from Wanlong Gao.
22) Fix a route refcounting issue in loopback driver, from Eric
Dumazet. There's a similar fix coming that we might add to the
macvlan driver as well.
23) Fix SKB leaks in batman-adv's distributed arp table code, from
Matthias Schiffer.
24) r8169 driver gives descriptor ownership back the hardware before
we're done reading the VLAN tag out of it, fix from Francois
Romieu.
25) Checksums not calculated properly in GRE tunnel driver fix from
Pravin B Shelar.
26) Fix SCTP memory leak on namespace exit."
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (101 commits)
dm9601: support dm9620 variant
SCTP: Free the per-net sysctl table on net exit. v2
net: phy: icplus: fix broken INTR pin settings
net: phy: icplus: Use the RGMII interface mode to configure clock delays
IP_GRE: Fix kernel panic in IP_GRE with GRE csum.
sctp: set association state to established in dupcook_a handler
ip6mr: limit IPv6 MRT_TABLE identifiers
r8169: fix vlan tag read ordering.
net: cdc_ncm: use IAD provided by the USB core
batman-adv: filter ARP packets with invalid MAC addresses in DAT
batman-adv: check for more types of invalid IP addresses in DAT
batman-adv: fix skb leak in batadv_dat_snoop_incoming_arp_reply()
net: loopback: fix a dst refcounting issue
virtio-net: reset virtqueue affinity when doing cpu hotplug
virtio-net: split out clean affinity function
virtio-net: fix the set affinity bug when CPU IDs are not consecutive
can: pch_can: fix invalid error codes
can: ti_hecc: fix invalid error codes
can: c_can: fix invalid error codes
r8169: remove the obsolete and incorrect AMD workaround
...
|
|
An issue has been reported where the PMIC either locks up or fails to
respond following a system Reset. This could result in a second write
in which the bus writes the current content of the write buffer to address
of the last I2C access.
The failure case is where this unwanted write transfers incorrect data to
a critical register.
This patch fixes this issue to by following any read or write with a dummy read
to a safe register address. A safe register address is one where the contents
will not affect the operation of the system.
Signed-off-by: Ashish Jangam <ashish.jangam@kpitcummins.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Add callback function conv_clk_and_div_n to convert between SSC clock
and its divider N.
For rtl8411, the formula to calculate SSC clock divider N is different
with the other card reader models.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Different card reader has different method to switch output voltage,
add this callback to let the card reader implement its individual switch
function.
This is needed as rtl8411 has a specific switch output voltage procedure.
Signed-off-by: Wei WANG <wei_wang@realsil.com.cn>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Here's a long-pending fixes pull request for arm-soc (I didn't send
one in the -rc4 cycle).
The larger deltas are from:
- A fixup of error paths in the mvsdio driver
- Header file move for a driver that hadn't been properly converted
to multiplatform on i.MX, which was causing build failures when
included
- Device tree updates for at91 dealing mostly with their new pinctrl
setup merged in 3.8 and mistakes in those initial configs
The rest are the normal mix of small fixes all over the place; sunxi,
omap, imx, mvebu, etc, etc."
* tag 'fixes-for-linus2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (40 commits)
mfd: vexpress-sysreg: Don't skip initialization on probe
ARM: vexpress: Enable A7 cores in V2P-CA15_A7's Device Tree
ARM: vexpress: extend the MPIDR range used for pen release check
ARM: at91/dts: correct comment in at91sam9x5.dtsi for mii
ARM: at91/at91_dt_defconfig: add at91sam9n12 SoC to DT defconfig
ARM: at91/at91_dt_defconfig: remove memory specification to cmdline
ARM: at91/dts: add macb mii pinctrl config for kizbox
ARM: at91: rm9200: remake the BGA as default version
ARM: at91: fix gpios on i2c-gpio for RM9200 DT
ARM: at91/at91sam9x5 DTS: add SCK USART pins
ARM: at91/at91sam9x5 DTS: correct wrong PIO BANK values on u(s)arts
ARM: at91/at91-pinctrl documentation: fix typo and add some details
ARM: kirkwood: fix missing #interrupt-cells property
mmc: mvsdio: use devm_ API to simplify/correct error paths.
clk: mvebu/clk-cpu.c: fix memory leakage
ARM: OMAP2+: omap4-panda: add UART2 muxing for WiLink shared transport
ARM: OMAP2+: DT node Timer iteration fix
ARM: OMAP2+: Fix section warning for omap_init_ocp2scp()
ARM: OMAP2+: fix build break for omapdrm
ARM: OMAP2: Fix missing omap2xxx_clkt_vps_late_init function calls
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k
Pull m68k fixes from Geert Uytterhoeven:
"The asm-generic changeset has been ack'ed by Arnd."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68k: Wire up finit_module
asm-generic/dma-mapping-broken.h: Provide dma_alloc_attrs()/dma_free_attrs()
m68k: Provide dma_alloc_attrs()/dma_free_attrs()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren:
Minimal omap fixes for the -rc series:
- A build fix for recently merged omap DRM changes
- Regression fixes from the common clock framework conversion
for omap4 audio and omap2 reboot
- Regression fix for pandaboard WLAN control UART muxing caused by
u-boot only muxing essential pins nowadays
- Timer iteration fix for CONFIG_OF_DYNAMIC
- A section mismatch fix for ocp2scp init
* tag 'omap-for-v3.8-rc4/fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: (306 commits)
ARM: OMAP2+: omap4-panda: add UART2 muxing for WiLink shared transport
ARM: OMAP2+: DT node Timer iteration fix
ARM: OMAP2+: Fix section warning for omap_init_ocp2scp()
ARM: OMAP2+: fix build break for omapdrm
ARM: OMAP2: Fix missing omap2xxx_clkt_vps_late_init function calls
ARM: OMAP4: hwmod_data: Correct IDLEMODE for McPDM
ARM: OMAP4: clock data: Lock ABE DPLL on all revisions
+ Linux 3.8-rc4
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
Pull libata fixes from Jeff Garzik:
1) ahci: Fix typo that caused erronenous error handling.
Thought: I wonder if sparse could have caught this, somehow.
2) ahci: support a slightly odd Enmotus variant
3) core: fix a drive detection problem by correcting the logic by which
the DevSlp timing variables are obtained and used.
* tag 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
[libata] replace sata_settings with devslp_timing
[libata] ahci: Add support for Enmotus Bobcat device.
[libata] ahci: Fix lack of command retry after a success error handler.
|
|
Cleanup and preparation for the next change.
signal_wake_up(resume => true) is overused. None of ptrace/jctl callers
actually want to wakeup a TASK_WAKEKILL task, but they can't specify the
necessary mask.
Turn signal_wake_up() into signal_wake_up_state(state), reintroduce
signal_wake_up() as a trivial helper, and add ptrace_signal_wake_up()
which adds __TASK_TRACED.
This way ptrace_signal_wake_up() can work "inside" ptrace_request()
even if the tracee doesn't have the TASK_WAKEKILL bit set.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
drivers/mfd/ab8500-core.c:1015:21: error: ‘ab8500_bm_data’ undeclared here
include/linux/mfd/abx500/ab8500-bm.h:445:13: warning: ‘ab8500_fg_reinit’ defined but not used
include/linux/mfd/abx500/ab8500-bm.h:448:13: warning: ‘ab8500_charger_usb_state_changed’ defined but not used
include/linux/mfd/abx500/ab8500-bm.h:451:29: warning: ‘ab8500_btemp_get’ defined but not used
include/linux/mfd/abx500/ab8500-bm.h:455:12: warning: ‘ab8500_btemp_get_batctrl_temp’ defined but not used
include/linux/mfd/abx500/ab8500-bm.h:463:12: warning: ‘ab8500_fg_inst_curr_blocking’ defined but not used
include/linux/mfd/abx500/ab8500-bm.h:442:12: warning: ‘ab8500_fg_inst_curr_done’ defined but not used
include/linux/mfd/abx500/ab8500-bm.h:447:26: warning: ‘ab8500_fg_get’ defined but not used
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
fixes
From Sascha Hauer:
ARM i.MX fixes for -rc.
This contains a single compilation fix for the CODA driver.
* tag 'imx-fixes-rc' of git://git.pengutronix.de/git/imx/linux-2.6:
[media] coda: Fix build due to iram.h rename
|
|
We do have some USB net devices, which cannot do ARP.
so we can introduce a new flag FLAG_NOARP, then client drivers
can easily handle this kind of devices
Signed-off-by: Wei Shuai <cpuwolf@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This implements a socket release callback function to check
if the socket cached route got invalid during the time
we owned the socket. The function is used from udp, raw
and ping sockets.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull module fixes and a virtio block fix from Rusty Russell:
"Various minor fixes, but a slightly more complex one to fix the
per-cpu overload problem introduced recently by kvm id changes."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
module: put modules in list much earlier.
module: add new state MODULE_STATE_UNFORMED.
module: prevent warning when finit_module a 0 sized file
virtio-blk: Don't free ida when disk is in use
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal
Pull misc syscall fixes from Al Viro:
- compat syscall fixes (discussed back in December)
- a couple of "make life easier for sigaltstack stuff by reducing
inter-tree dependencies"
- fix up compiler/asmlinkage calling convention disagreement of
sys_clone()
- misc
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal:
sys_clone() needs asmlinkage_protect
make sure that /linuxrc has std{in,out,err}
x32: fix sigtimedwait
x32: fix waitid()
switch compat_sys_wait4() and compat_sys_waitid() to COMPAT_SYSCALL_DEFINE
switch compat_sys_sigaltstack() to COMPAT_SYSCALL_DEFINE
CONFIG_GENERIC_SIGALTSTACK build breakage with asm-generic/syscalls.h
Ensure that kernel_init_freeable() is not inlined into non __init code
|
|
The ia64 function "thread_matches()" has no users since commit
e868a55c2a8c ("[IA64] remove find_thread_for_addr()"). Remove it.
This allows us to make ptrace_check_attach() static to kernel/ptrace.c,
which is good since we'll need to change the semantics of it and fix up
all the callers.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg Kroah-Hartman:
"Here are a few tty/serial driver fixes for 3.8-rc4 that resolve a
number of problems that people have been having, including the ptys
ioctl issue that is a regression fix"
* tag 'tty-3.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
8250/16?50: Add support for Broadcom TruManage redirected serial port
pty: return EINVAL for TIOCGPTN for BSD ptys
serial:ifx6x60:Keep word size accordance with SPI controller
tty: 8250_dw: Fix inverted arguments to serial_out in IRQ handler
serial: samsung: remove redundant setting of line config during port reset
serial:ifx6x60:Delete SPI timer when shut down port
tty/8250: The correct device id for this card is 0x0022
tty/8250: pbn_b0_8_1152000_200 is supposed to be an 8 port definition
tty: serial: vt8500: fix return value check in vt8500_serial_probe()
serial: mxs-auart: Index is unsigned
mxs: uart: fix setting RTS from software
|
|
Commit 816422ad7647 ("asm-generic, mm: pgtable: consolidate zero page
helpers") broke the compile on MIPS if SPARSEMEM is enabled. We get
this:
In file included from arch/mips/include/asm/pgtable.h:552,
from include/linux/mm.h:44,
from arch/mips/kernel/asm-offsets.c:14:
include/asm-generic/pgtable.h: In function 'my_zero_pfn':
include/asm-generic/pgtable.h:466: error: implicit declaration of function 'page_to_section'
In file included from arch/mips/kernel/asm-offsets.c:14:
include/linux/mm.h: At top level:
include/linux/mm.h:738: error: conflicting types for 'page_to_section'
include/asm-generic/pgtable.h:466: note: previous implicit declaration of 'page_to_section' was here
Due header files inter-dependencies, the only way I see to fix it is
convert my_zero_pfn() for __HAVE_COLOR_ZERO_PAGE to macros.
Signed-off-by: Kirill A. Shutemov <kirill@shutemov.name>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: David Daney <david.daney@cavium.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add support for the UART device present in Broadcom TruManage capable
NetXtreme chips (ie: 5761m 5762, and 5725).
This implementation has a hidden transmit FIFO, so running in single-byte
interrupt mode results in too many interrupts. The UART_CAP_HFIFO
capability was added to track this. It continues to reload the THR as long
as the THRE and TSRE bits are set in the LSR up to a specified limit (1024
is used here).
Signed-off-by: Stephen Hurd <shurd@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
- cpuidle regression fix related to the initialization of state
kobjects from Krzysztof Mazur.
- cpuidle fix removing some not very useful code and making some
user-visible problems go away at the same time. From Daniel Lezcano.
- ACPI build fix from Yinghai Lu.
* tag 'pm+acpi-for-3.8-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpuidle: remove the power_specified field in the driver
ACPI / glue: Fix build with ACPI_GLUE_DEBUG set
cpuidle: fix number of initialized/destroyed states
|
|
Commit 1b963c81b145 ("lockdep, rwsem: provide down_write_nest_lock()")
contains a bug in a codepath when CONFIG_DEBUG_LOCK_ALLOC is disabled,
which causes down_read() to be called instead of down_write() by mistake
on such configurations. Fix that.
Reported-and-tested-by: Andrew Clayton <andrew@digital-domain.net>
Reported-and-tested-by: Zlatko Calusic <zlatko.calusic@iskon.hr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Reviewed-by: Rik van Riel <riel@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull scsi target fixes from Nicholas Bellinger:
"This includes an important >= v3.6 regression bugfix for active I/O
shutdown (Roland), some TMR related failure / corner cases fixes for
long outstanding I/O (Roland), two FCoE target mode fabric fabric role
fixes (MDR), a fix for an incorrect sense code during LUN
communication failure (Dr. Hannes), plus a handful of other minor
fixes.
There are still some outstanding zero-length control CDB regression
fixes that need to be addressed for v3.8, that will be coming in a
follow-up PULL request."
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
iscsi-target: Fix CmdSN comparison (use cmd->cmd_sn instead of cmd->stat_sn)
target: Release se_cmd when LUN lookup fails for TMR
target: Fix use-after-free in LUN RESET handling
target: Fix missing CMD_T_ACTIVE bit regression for pending WRITEs
tcm_fc: Do not report target role when target is not defined
tcm_fc: Do not indicate retry capability to initiators
target: Use TCM_NO_SENSE for initialisation
target: Introduce TCM_NO_SENSE
target: use correct sense code for LUN communication failure
|
|
If the default iosched is built as module, the kernel may deadlock
while trying to load the iosched module on device probe if the probing
was running off async. This is because async_synchronize_full() at
the end of module init ends up waiting for the async job which
initiated the module loading.
async A modprobe
1. finds a device
2. registers the block device
3. request_module(default iosched)
4. modprobe in userland
5. load and init module
6. async_synchronize_full()
Async A waits for modprobe to finish in request_module() and modprobe
waits for async A to finish in async_synchronize_full().
Because there's no easy to track dependency once control goes out to
userland, implementing properly nested flushing is difficult. For
now, make module init perform async_synchronize_full() iff module init
has queued async jobs as suggested by Linus.
This avoids the described deadlock because iosched module doesn't use
async and thus wouldn't invoke async_synchronize_full(). This is
hacky and incomplete. It will deadlock if async module loading nests;
however, this works around the known problem case and seems to be the
best of bad options.
For more details, please refer to the following thread.
http://thread.gmane.org/gmane.linux.kernel/1420814
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Alex Riesen <raa.lkml@gmail.com>
Tested-by: Ming Lei <ming.lei@canonical.com>
Tested-by: Alex Riesen <raa.lkml@gmail.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
We realized that the power usage field is never filled and when it
is filled for tegra, the power_specified flag is not set causing all
of these values to be reset when the driver is initialized with
set_power_state().
However, the power_specified flag can be simply removed under the
assumption that the states are always backward sorted, which is the
case with the current code.
This change allows the menu governor select function and the
cpuidle_play_dead() to be simplified. Moreover, the
set_power_states() function can removed as it does not make sense
any more.
Drop the power_specified flag from struct cpuidle_driver and make
the related changes as described above.
As a consequence, this also fixes the bug where on the dynamic
C-states system, the power fields are not initialized.
[rjw: Changelog]
References: https://bugzilla.kernel.org/show_bug.cgi?id=42870
References: https://bugzilla.kernel.org/show_bug.cgi?id=43349
References: https://lkml.org/lkml/2012/10/16/518
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Pablo Neira Ayuso says:
====================
The following patchset contains netfilter fixes for 3.8-rc3,
they are:
* fix possible BUG_ON if several netns are in use and the nf_conntrack
module is removed, initial patch from Gao feng, final patch from myself.
* fix unset return value if conntrack zone are disabled at
compile-time, reported by Borislav Petkov, fix from myself.
* fix display error message via dmesg for arp_tables, from Jan Engelhardt.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch corrects some problems with LSM/SELinux that were introduced
with the multiqueue patchset. The problem stems from the fact that the
multiqueue work changed the relationship between the tun device and its
associated socket; before the socket persisted for the life of the
device, however after the multiqueue changes the socket only persisted
for the life of the userspace connection (fd open). For non-persistent
devices this is not an issue, but for persistent devices this can cause
the tun device to lose its SELinux label.
We correct this problem by adding an opaque LSM security blob to the
tun device struct which allows us to have the LSM security state, e.g.
SELinux labeling information, persist for the lifetime of the tun
device. In the process we tweak the LSM hooks to work with this new
approach to TUN device/socket labeling and introduce a new LSM hook,
security_tun_dev_attach_queue(), to approve requests to attach to a
TUN queue via TUNSETQUEUE.
The SELinux code has been adjusted to match the new LSM hooks, the
other LSMs do not make use of the LSM TUN controls. This patch makes
use of the recently added "tun_socket:attach_queue" permission to
restrict access to the TUNSETQUEUE operation. On older SELinux
policies which do not define the "tun_socket:attach_queue" permission
the access control decision for TUNSETQUEUE will be handled according
to the SELinux policy's unknown permission setting.
Signed-off-by: Paul Moore <pmoore@redhat.com>
Acked-by: Eric Paris <eparis@parisplace.org>
Tested-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Most of commits found here are for ASoC device specific fixes,
arizona, cs4271, wm5102, wm2200, etc, in addition to a couple of
memory leak fixes in ASoC core.
Other than that, regression fixes in HD-audio and USB-audio, and a fix
for new Realtek codecs."
* tag 'sound-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (30 commits)
ALSA: usb-audio: Fix NULL dereference by access to non-existing substream
ALSA: hda - Add support of new codec ALC284
ALSA: usb-audio: Make ebox44_table static
ALSA: hdspm - Fix wordclock status on AES32
Revert "ALSA: hda - Shut up pins at power-saving mode with Conexnat codecs"
ALSA: hda - Disable runtime D3 for Intel CPT & co
ALSA: pxa27x: fix ac97 warm reset
ALSA: pxa27x: fix ac97 cold reset
ASoC: wm_adsp: Ensure that block writes are from DMA aligned addresses
ASoC: wm2000: Fix sense of speech clarity enable
ASoC: wm5100: Remove DSP B and left justified formats
ASoC: arizona: Remove DSP B and left justified AIF modes
ASoC: wm2200: Remove DSP B and left justified AIF modes
ASoC: wm5102: Improve speaker enable performance
ASoC: core: fix the memory leak in case of remove_aux_dev()
ASoC: core: fix the memory leak in case of device_add() failure
ASoC: cs42l52: Catch no-match case in cs42l52_get_clk
ASoC: lm49453: Update lm49453_reg_defs values as per LM49453 HW revision-B
ASoC: lm49453: Fix adc, mic and sidetone volume ranges
ASoC: arizona: Correct FLL source definitions
...
|
|
NCQ capability was used to check availability of SATA Settings page
from Identify Device Data Log, which contains DevSlp timing variables.
It does not work on some HDDs and leads to error messages.
IDENTIFY word 78 bit 5(Hardware Feature Control) can't work either
because it is only the sufficient condition of Identify Device data
log, not the necessary condition.
This patch replaced ata_device->sata_settings with ->devslp_timing
to only save DevSlp timing variables(8 bytes), instead of the whole
SATA Settings page(512 bytes).
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=51881
Reported-by: Borislav Petkov <bp@alien8.de>
Signed-off-by: Shane Huang <shane.huang@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg Kroah-Hartman:
"Here are two patches for 3.8-rc3.
One removes the __dev* defines from init.h now that all usages of it
are gone from your tree. The other fix is for debugfs's paramater
that was using the wrong base for the option.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'driver-core-3.8-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
debugfs: convert gid= argument from decimal, not octal
Remove __dev* markings from init.h
|
|
Pull networking fixes from David Miller:
1) Fix regression allowing IP_TTL setting of zero, fix from Cong Wang.
2) Fix leak regressions in tunap, from Jason Wang.
3) be2net driver always returns IRQ_HANDLED in INTx handler, fix from
Sathya Perla.
4) qlge doesn't really support NETIF_F_TSO6, don't set that flag. Fix
from Amerigo Wang.
5) Add 802.11ad Atheros wil6210 driver, from Vladimir Kondratiev.
6) Fix MTU calculations in mac80211 layer, from T Krishna Chaitanya.
7) Station info layer of mac80211 needs to use del_timer_sync(), from
Johannes Berg.
8) tcp_read_sock() can loop forever, because we don't immediately stop
when recv_actor() returns zero. Fix from Eric Dumazet.
9) Fix WARN_ON() in tcp_cleanup_rbuf(). We have to use sk_eat_skb() in
tcp_recv_skb() to handle the case where a large GRO packet is split
up while it is use by a splice() operation. Fix also from Eric
Dumazet.
10) addrconf_get_prefix_route() in ipv6 tests flags incorrectly, it
does:
if (X && (p->flags & Y) != 0)
when it really meant to go:
if (X && (p->flags & X) != 0)
fix from Romain Kuntz.
11) Fix lost Kconfig dependency for bfin_mac driver hardware
timestamping. From Lars-Peter Clausen.
12) Fix regression in handling of RST without ACK in TCP, from Eric
Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (37 commits)
be2net: fix unconditionally returning IRQ_HANDLED in INTx
tuntap: fix leaking reference count
tuntap: forbid calling TUNSETIFF when detached
tuntap: switch to use rtnl_dereference()
net, wireless: overwrite default_ethtool_ops
qlge: remove NETIF_F_TSO6 flag
tcp: accept RST without ACK flag
net: ethernet: xilinx: Do not use NO_IRQ in axienet
net: ethernet: xilinx: Do not use axienet on PPC
bnx2x: Allow management traffic after boot from SAN
bnx2x: Fix fastpath structures when memory allocation fails
bfin_mac: Restore hardware time-stamping dependency on BF518
tun: avoid owner checks on IFF_ATTACH_QUEUE
bnx2x: move debugging code before the return
tuntap: refuse to re-attach to different tun_struct
ipv6: use addrconf_get_prefix_route for prefix route lookup [v2]
ipv6: fix the noflags test in addrconf_get_prefix_route
tcp: fix splice() and tcp collapsing interaction
tcp: splice: fix an infinite loop in tcp_read_sock()
net: prevent setting ttl=0 via IP_TTL
...
|
|
canqun zhang reported that we're hitting BUG_ON in the
nf_conntrack_destroy path when calling kfree_skb while
rmmod'ing the nf_conntrack module.
Currently, the nf_ct_destroy hook is being set to NULL in the
destroy path of conntrack.init_net. However, this is a problem
since init_net may be destroyed before any other existing netns
(we cannot assume any specific ordering while releasing existing
netns according to what I read in recent emails).
Thanks to Gao feng for initial patch to address this issue.
Reported-by: canqun zhang <canqunzhang@gmail.com>
Acked-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
You should never look at such a module, so it's excised from all paths
which traverse the modules list.
We add the state at the end, to avoid gratuitous ABI break (ksplice).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
|
|
Since:
commit 2c60db037034d27f8c636403355d52872da92f81
Author: Eric Dumazet <edumazet@google.com>
Date: Sun Sep 16 09:17:26 2012 +0000
net: provide a default dev->ethtool_ops
wireless core does not correctly assign ethtool_ops.
After alloc_netdev*() call, some cfg80211 drivers provide they own
ethtool_ops, but some do not. For them, wireless core provide generic
cfg80211_ethtool_ops, which is assigned in NETDEV_REGISTER notify call:
if (!dev->ethtool_ops)
dev->ethtool_ops = &cfg80211_ethtool_ops;
But after Eric's commit, dev->ethtool_ops is no longer NULL (on cfg80211
drivers without custom ethtool_ops), but points to &default_ethtool_ops.
In order to fix the problem, provide function which will overwrite
default_ethtool_ops and use it by wireless core.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Merge misc fixes from Andrew Morton:
"The audit fixes have been floating around for a while - Al and Eric
aren't responding to either myself or Kees so I asked Kees to
re-review them and here they are."
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (22 commits)
lib/rbtree.c: avoid the use of non-static __always_inline
MAINTAINERS: Omar had moved
mm: compaction: partially revert capture of suitable high-order page
linux/audit.h: move ptrace.h include to kernel header
kernel/audit.c: avoid negative sleep durations
audit: catch possible NULL audit buffers
audit: create explicit AUDIT_SECCOMP event type
MAINTAINERS: fix a status pattern
MAINTAINERS: fix arch/arm/plat-omap/include/plat/omap_hwmod.h
mm: thp: acquire the anon_vma rwsem for write during split
mm: mmap: annotate vm_lock_anon_vma locking properly for lockdep
lockdep, rwsem: provide down_write_nest_lock()
arch/mn10300/Kconfig: select CONFIG_GENERIC_ATOMIC64
mm: bootmem: fix free_all_bootmem_core() with odd bitmap alignment
mm: use aligned zone start for pfn_to_bitidx calculation
fs/exec.c: work around icc miscompilation
mm: compaction: fix echo 1 > compact_memory return error issue
mm: memblock: fix wrong memmove size in memblock_merge_regions()
drivers/video/ssd1307fb.c: fix bit order bug in the byte translation function
mm: migrate: check page_count of THP before migrating
...
|
|
lib/rbtree.c declared __rb_erase_color() as __always_inline void, and
then exported it with EXPORT_SYMBOL.
This was because __rb_erase_color() must be exported for augmented
rbtree users, but it must also be inlined into rb_erase() so that the
dummy callback can get optimized out of that call site.
(Actually with a modern compiler, none of the dummy callback functions
should even be generated as separate text functions).
The above usage is legal C, but it was unusual enough for some compilers
to warn about it. This change makes things more explicit, with a static
__always_inline ____rb_erase_color function for use in rb_erase(), and a
separate non-inline __rb_erase_color function for use in
rb_erase_augmented call sites.
Signed-off-by: Michel Lespinasse <walken@google.com>
Reported-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Eric Wong reported on 3.7 and 3.8-rc2 that ppoll() got stuck when
waiting for POLLIN on a local TCP socket. It was easier to trigger if
there was disk IO and dirty pages at the same time and he bisected it to
commit 1fb3f8ca0e92 ("mm: compaction: capture a suitable high-order page
immediately when it is made available").
The intention of that patch was to improve high-order allocations under
memory pressure after changes made to reclaim in 3.6 drastically hurt
THP allocations but the approach was flawed. For Eric, the problem was
that page->pfmemalloc was not being cleared for captured pages leading
to a poor interaction with swap-over-NFS support causing the packets to
be dropped. However, I identified a few more problems with the patch
including the fact that it can increase contention on zone->lock in some
cases which could result in async direct compaction being aborted early.
In retrospect the capture patch took the wrong approach. What it should
have done is mark the pageblock being migrated as MIGRATE_ISOLATE if it
was allocating for THP and avoided races that way. While the patch was
showing to improve allocation success rates at the time, the benefit is
marginal given the relative complexity and it should be revisited from
scratch in the context of the other reclaim-related changes that have
taken place since the patch was first written and tested. This patch
partially reverts commit 1fb3f8ca0e92 ("mm: compaction: capture a
suitable high-order page immediately when it is made available").
Reported-and-tested-by: Eric Wong <normalperson@yhbt.net>
Tested-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Mel Gorman <mgorman@suse.de>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
While the kernel internals want pt_regs (and so it includes
linux/ptrace.h), the user version of audit.h does not need it. So move
the include out of the uapi version.
This avoids issues where people want the audit defines and userland
ptrace api. Including both the kernel ptrace and the userland ptrace
headers can easily lead to failure.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Cc: Eric Paris <eparis@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The seccomp path was using AUDIT_ANOM_ABEND from when seccomp mode 1
could only kill a process. While we still want to make sure an audit
record is forced on a kill, this should use a separate record type since
seccomp mode 2 introduces other behaviors.
In the case of "handled" behaviors (process wasn't killed), only emit a
record if the process is under inspection. This change also fixes
userspace examination of seccomp audit events, since it was considered
malformed due to missing fields of the AUDIT_ANOM_ABEND event type.
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Eric Paris <eparis@redhat.com>
Cc: Jeff Layton <jlayton@redhat.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Julien Tinnes <jln@google.com>
Acked-by: Will Drewry <wad@chromium.org>
Acked-by: Steve Grubb <sgrubb@redhat.com>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
down_write_nest_lock() provides a means to annotate locking scenario
where an outer lock is guaranteed to serialize the order nested locks
are being acquired.
This is analogoue to already existing mutex_lock_nest_lock() and
spin_lock_nest_lock().
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Cc: Rik van Riel <riel@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mel Gorman <mel@csn.ul.ie>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
In some cases, free_irq_cpu_rmap() is called while holding a lock (eg
rtnl). This can lead to deadlocks, because it invokes
flush_scheduled_work() which ends up waiting for whole system workqueue
to flush, but some pending works might try to acquire the lock we are
already holding.
This commit uses reference-counting to replace
irq_run_affinity_notifiers(). It also removes
irq_run_affinity_notifiers() altogether.
[akpm@linux-foundation.org: eliminate free_cpu_rmap, rename cpu_rmap_reclaim() to cpu_rmap_release(), propagate kref_put() retval from cpu_rmap_put()]
Signed-off-by: David Decotigny <decot@googlers.com>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Acked-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull intel DRM fixes from Dave Airlie:
"Just intel fixes, including getting the Ironlake systems back to the
state they were in for 3.6."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/i915: Revert shrinker changes from "Track unbound pages"
drm/i915: Use pixel size for computing linear offsets into a sprite
drm/i915: Add DEBUG messages to all intel_create_user_framebuffer error paths
drm/i915: The sprite scaler on Ironlake also support YUV planes
drm: Only evict the blocks required to create the requested hole
drm/i915: Treat crtc->mode.clock == 0 as disabled
Revert "drm/i915: no lvds quirk for Zotac ZDBOX SD ID12/ID13"
drm/i915; Only increment the user-pin-count after successfully pinning the bo
|
|
Eric Wong reported on 3.7 and 3.8-rc2 that ppoll() got stuck when
waiting for POLLIN on a local TCP socket. It was easier to trigger if
there was disk IO and dirty pages at the same time and he bisected it to
commit 1fb3f8ca0e92 ("mm: compaction: capture a suitable high-order page
immediately when it is made available").
The intention of that patch was to improve high-order allocations under
memory pressure after changes made to reclaim in 3.6 drastically hurt
THP allocations but the approach was flawed. For Eric, the problem was
that page->pfmemalloc was not being cleared for captured pages leading
to a poor interaction with swap-over-NFS support causing the packets to
be dropped. However, I identified a few more problems with the patch
including the fact that it can increase contention on zone->lock in some
cases which could result in async direct compaction being aborted early.
In retrospect the capture patch took the wrong approach. What it should
have done is mark the pageblock being migrated as MIGRATE_ISOLATE if it
was allocating for THP and avoided races that way. While the patch was
showing to improve allocation success rates at the time, the benefit is
marginal given the relative complexity and it should be revisited from
scratch in the context of the other reclaim-related changes that have
taken place since the patch was first written and tested. This patch
partially reverts commit 1fb3f8ca "mm: compaction: capture a suitable
high-order page immediately when it is made available".
Reported-and-tested-by: Eric Wong <normalperson@yhbt.net>
Tested-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mel Gorman <mgorman@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Introduce TCM_NO_SENSE, mapping to sense code
'Not ready, no additional sense information'.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Cc: Nicholas Bellinger <nab@risingtidesystems.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Daniel writes:
"Pretty much all just major fixes:
- 2 pieces of duct-tape for the ilk bug.
- Sprite regression fixes from Chris.
- OOPS fix for a div-by-zero from Chris, regression due to the modeset
rework in 3.7, now brought to light by a benign change in 3.8.
- Fix interrupted bo pinning, used to work around CS coherency issues on
i830/i845 (kernel also has a w/a newly in 3.8, but pinning is more efficient if
possible)."
|
