| Age | Commit message (Collapse) | Author |
|---|
|
INIT_IPS and GATE_ENABLE fields have a wrong offset in SG_CONFIG_REG_3.
This register is used by stream gate control of PSFP, and it has not
been used before, because PSFP is not implemented in ocelot driver.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Documentation/networking/ip-sysctl.txt:46 says:
ip_forward_use_pmtu - BOOLEAN
By default we don't trust protocol path MTUs while forwarding
because they could be easily forged and can lead to unwanted
fragmentation by the router.
You only need to enable this if you have user-space software
which tries to discover path mtus by itself and depends on the
kernel honoring this information. This is normally not the case.
Default: 0 (disabled)
Possible values:
0 - disabled
1 - enabled
Which makes it pretty clear that setting it to 1 is a potential
security/safety/DoS issue, and yet it is entirely reasonable to want
forwarded traffic to honour explicitly administrator configured
route mtus (instead of defaulting to device mtu).
Indeed, I can't think of a single reason why you wouldn't want to.
Since you configured a route mtu you probably know better...
It is pretty common to have a higher device mtu to allow receiving
large (jumbo) frames, while having some routes via that interface
(potentially including the default route to the internet) specify
a lower mtu.
Note that ipv6 forwarding uses device mtu unless the route is locked
(in which case it will use the route mtu).
This approach is not usable for IPv4 where an 'mtu lock' on a route
also has the side effect of disabling TCP path mtu discovery via
disabling the IPv4 DF (don't frag) bit on all outgoing frames.
I'm not aware of a way to lock a route from an IPv6 RA, so that also
potentially seems wrong.
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Lorenzo Colitti <lorenzo@google.com>
Cc: Sunmeet Gill (Sunny) <sgill@quicinc.com>
Cc: Vinay Paradkar <vparadka@qti.qualcomm.com>
Cc: Tyler Wear <twear@quicinc.com>
Cc: David Ahern <dsahern@kernel.org>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All TC actions call tcf_idr_insert() for new action at the end
of their ->init(), so we can actually move it to a central place
in tcf_action_init_1().
And once the action is inserted into the global IDR, other parallel
process could free it immediately as its refcnt is still 1, so we can
not fail after this, we need to move it after the goto action
validation to avoid handling the failure case after insertion.
This is found during code review, is not directly triggered by syzbot.
And this prepares for the next patch.
Cc: Vlad Buslov <vladbu@mellanox.com>
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull vfs fixes from Al Viro:
"No common topic, just assorted fixes"
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fuse: fix the ->direct_IO() treatment of iov_iter
fs: fix cast in fsparam_u32hex() macro
vboxsf: Fix the check for the old binary mount-arguments struct
|
|
Pull networking fixes from Jakub Kicinski:
- fix failure to add bond interfaces to a bridge, the offload-handling
code was too defensive there and recent refactoring unearthed that.
Users complained (Ido)
- fix unnecessarily reflecting ECN bits within TOS values / QoS marking
in TCP ACK and reset packets (Wei)
- fix a deadlock with bpf iterator. Hopefully we're in the clear on
this front now... (Yonghong)
- BPF fix for clobbering r2 in bpf_gen_ld_abs (Daniel)
- fix AQL on mt76 devices with FW rate control and add a couple of AQL
issues in mac80211 code (Felix)
- fix authentication issue with mwifiex (Maximilian)
- WiFi connectivity fix: revert IGTK support in ti/wlcore (Mauro)
- fix exception handling for multipath routes via same device (David
Ahern)
- revert back to a BH spin lock flavor for nsid_lock: there are paths
which do require the BH context protection (Taehee)
- fix interrupt / queue / NAPI handling in the lantiq driver (Hauke)
- fix ife module load deadlock (Cong)
- make an adjustment to netlink reply message type for code added in
this release (the sole change touching uAPI here) (Michal)
- a number of fixes for small NXP and Microchip switches (Vladimir)
[ Pull request acked by David: "you can expect more of this in the
future as I try to delegate more things to Jakub" ]
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (167 commits)
net: mscc: ocelot: fix some key offsets for IP4_TCP_UDP VCAP IS2 entries
net: dsa: seville: fix some key offsets for IP4_TCP_UDP VCAP IS2 entries
net: dsa: felix: fix some key offsets for IP4_TCP_UDP VCAP IS2 entries
inet_diag: validate INET_DIAG_REQ_PROTOCOL attribute
net: bridge: br_vlan_get_pvid_rcu() should dereference the VLAN group under RCU
net: Update MAINTAINERS for MediaTek switch driver
net/mlx5e: mlx5e_fec_in_caps() returns a boolean
net/mlx5e: kTLS, Avoid kzalloc(GFP_KERNEL) under spinlock
net/mlx5e: kTLS, Fix leak on resync error flow
net/mlx5e: kTLS, Add missing dma_unmap in RX resync
net/mlx5e: kTLS, Fix napi sync and possible use-after-free
net/mlx5e: TLS, Do not expose FPGA TLS counter if not supported
net/mlx5e: Fix using wrong stats_grps in mlx5e_update_ndo_stats()
net/mlx5e: Fix multicast counter not up-to-date in "ip -s"
net/mlx5e: Fix endianness when calculating pedit mask first bit
net/mlx5e: Enable adding peer miss rules only if merged eswitch is supported
net/mlx5e: CT: Fix freeing ct_label mapping
net/mlx5e: Fix memory leak of tunnel info when rule under multipath not ready
net/mlx5e: Use synchronize_rcu to sync with NAPI
net/mlx5e: Use RCU to protect rq->xdp_prog
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
- Check kprobe is enabled before unregistering from ftrace as it isn't
registered when disabled.
- Remove kprobes enabled via command-line that is on init text when
freed.
- Add missing RCU synchronization for ftrace trampoline symbols removed
from kallsyms.
- Free trampoline on error path if ftrace_startup() fails.
- Give more space for the longer PID numbers in trace output.
- Fix a possible double free in the histogram code.
- A couple of fixes that were discovered by sparse.
* tag 'trace-v5.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
bootconfig: init: make xbc_namebuf static
kprobes: tracing/kprobes: Fix to kill kprobes on initmem after boot
tracing: fix double free
ftrace: Let ftrace_enable_sysctl take a kernel pointer buffer
tracing: Make the space reserved for the pid wider
ftrace: Fix missing synchronize_rcu() removing trampoline from kallsyms
ftrace: Free the trampoline when ftrace_startup() fails
kprobes: Fix to check probe enabled before disarm_kprobe_ftrace()
|
|
dax_supported() is defined whenever CONFIG_DAX is enabled. So dummy
implementation should be defined only in !CONFIG_DAX case, not in
!CONFIG_FS_DAX case.
Fixes: e2ec51282545 ("dm: Call proper helper to determine dax support")
Cc: <stable@vger.kernel.org>
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking fixes from Borislav Petkov:
"Two fixes from the locking/urgent pile:
- Fix lockdep's detection of "USED" <- "IN-NMI" inversions (Peter
Zijlstra)
- Make percpu-rwsem operations on the semaphore's ->read_count
IRQ-safe because it can be used in an IRQ context (Hou Tao)"
* tag 'locking_urgent_for_v5.9_rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
locking/percpu-rwsem: Use this_cpu_{inc,dec}() for read_count
locking/lockdep: Fix "USED" <- "IN-NMI" inversions
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fixes from Dan Williams:
"A handful of fixes to address a string of mistakes in the mechanism
for device-mapper to determine if its component devices are dax
capable.
- Fix an original bug in device-mapper table reference counting when
interrogating dax capability in the component device. This bug was
hidden by the following bug.
- Fix device-mapper to use the proper helper (dax_supported() instead
of the leaf helper generic_fsdax_supported()) to determine dax
operation of a stacked block device configuration. The original
implementation is only valid for one level of dax-capable block
device stacking. This bug was discovered while fixing the below
regression.
- Fix an infinite recursion regression introduced by broken attempts
to quiet the generic_fsdax_supported() path and make it bail out
before logging "dax capability not found" errors"
* tag 'libnvdimm-fixes-5.9-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
dax: Fix stack overflow when mounting fsdax pmem device
dm: Call proper helper to determine dax support
dm/dax: Fix table reference counts
|
|
When calculating ancestor_size with IPv6 enabled, simply using
sizeof(struct ipv6_pinfo) doesn't account for extra bytes needed for
alignment in the struct sctp6_sock. On x86, there aren't any extra
bytes, but on ARM the ipv6_pinfo structure is aligned on an 8-byte
boundary so there were 4 pad bytes that were omitted from the
ancestor_size calculation. This would lead to corruption of the
pd_lobby pointers, causing an oops when trying to free the sctp
structure on socket close.
Fixes: 636d25d557d1 ("sctp: not copy sctp_sock pd_lobby in sctp_copy_descendant")
Signed-off-by: Henry Ptasinski <hptasinski@google.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial/fbcon fixes from Greg KH:
"Here are some small tty/serial and one more fbcon fix.
They include:
- serial core locking regression fixes
- new device ids for 8250_pci driver
- fbcon fix for syzbot found issue
All have been in linux-next with no reported issues"
* tag 'tty-5.9-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
fbcon: Fix user font detection test at fbcon_resize().
serial: 8250_pci: Add Realtek 816a and 816b
serial: core: fix console port-lock regression
serial: core: fix port-lock initialisation
|
|
DM was calling generic_fsdax_supported() to determine whether a device
referenced in the DM table supports DAX. However this is a helper for "leaf" device drivers so that
they don't have to duplicate common generic checks. High level code
should call dax_supported() helper which that calls into appropriate
helper for the particular device. This problem manifested itself as
kernel messages:
dm-3: error: dax access failed (-95)
when lvm2-testsuite run in cases where a DM device was stacked on top of
another DM device.
Fixes: 7bf7eac8d648 ("dax: Arrange for dax_supported check to span multiple devices")
Cc: <stable@vger.kernel.org>
Tested-by: Adrian Huang <ahuang12@lenovo.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/160061715195.13131.5503173247632041975.stgit@dwillia2-desk3.amr.corp.intel.com
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Commit 32927393dc1c ("sysctl: pass kernel pointers to ->proc_handler")
changed ctl_table.proc_handler to take a kernel pointer. Adjust the
signature of stack_erasing_sysctl to match ctl_table.proc_handler which
fixes the following sparse warning:
kernel/stackleak.c:31:50: warning: incorrect type in argument 3 (different address spaces)
kernel/stackleak.c:31:50: expected void *
kernel/stackleak.c:31:50: got void [noderef] __user *buffer
Fixes: 32927393dc1c ("sysctl: pass kernel pointers to ->proc_handler")
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Link: https://lkml.kernel.org/r/20200907093253.13656-1-tklauser@distanz.ch
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Commit 32927393dc1c ("sysctl: pass kernel pointers to ->proc_handler")
changed ctl_table.proc_handler to take a kernel pointer. Adjust the
signature of ftrace_enable_sysctl to match ctl_table.proc_handler which
fixes the following sparse warning:
kernel/trace/ftrace.c:7544:43: warning: incorrect type in argument 3 (different address spaces)
kernel/trace/ftrace.c:7544:43: expected void *
kernel/trace/ftrace.c:7544:43: got void [noderef] __user *buffer
Fixes: 32927393dc1c ("sysctl: pass kernel pointers to ->proc_handler")
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Link: https://lkml.kernel.org/r/20200907093207.13540-1-tklauser@distanz.ch
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Currently mscc_ocelot_init_ports() will skip initializing a port when it
doesn't have a phy-handle, so the ocelot->ports[port] pointer will be
NULL. Take this into consideration when tearing down the driver, and add
a new function ocelot_deinit_port() to the switch library, mirror of
ocelot_init_port(), which needs to be called by the driver for all ports
it has initialized.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ocelot_port->ts_id is used to:
(a) populate skb->cb[0] for matching the TX timestamp in the PTP IRQ
with an skb.
(b) populate the REW_OP from the injection header of the ongoing skb.
Only then is ocelot_port->ts_id incremented.
This is a problem because, at least theoretically, another timestampable
skb might use the same ocelot_port->ts_id before that is incremented.
Normally all transmit calls are serialized by the netdev transmit
spinlock, but in this case, ocelot_port_add_txtstamp_skb() is also
called by DSA, which has started declaring the NETIF_F_LLTX feature
since commit 2b86cb829976 ("net: dsa: declare lockless TX feature for
slave ports"). So the logic of using and incrementing the timestamp id
should be atomic per port.
The solution is to use the global ocelot_port->ts_id only while
protected by the associated ocelot_port->ts_id_lock. That's where we
populate skb->cb[0]. Note that for ocelot, ocelot_port_add_txtstamp_skb
is called for the actual skb, but for felix, it is called for the skb's
clone. That is something which will also be changed in the future.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- Allow CPUs affected by erratum 1418040 to come online late
(previously we only fixed the other case - CPUs not affected by the
erratum coming up late).
- Fix branch offset in BPF JIT.
- Defer the stolen time initialisation to the CPU online time from the
CPU starting time to avoid a (sleep-able) memory allocation in an
atomic context.
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: paravirt: Initialize steal time when cpu is online
arm64: bpf: Fix branch offset in JIT
arm64: Allow CPUs unffected by ARM erratum 1418040 to come in late
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These add a new CPU ID to the RAPL power capping driver and prevent
the ACPI processor idle driver from triggering RCU-lockdep complaints.
Specifics:
- Add support for the Lakefield chip to the RAPL power capping driver
(Ricardo Neri).
- Modify the ACPI processor idle driver to prevent it from triggering
RCU-lockdep complaints which has started to happen after recent
changes in that area (Peter Zijlstra)"
* tag 'pm-5.9-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: processor: Take over RCU-idle for C3-BM idle
cpuidle: Allow cpuidle drivers to take over RCU-idle
ACPI: processor: Use CPUIDLE_FLAG_TLB_FLUSHED
ACPI: processor: Use CPUIDLE_FLAG_TIMER_STOP
powercap: RAPL: Add support for Lakefield
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Here is a collection of fixes for 5.9. All look small and are nothing
scary.
The majority of changes are about ASoC driver- specific fixes, while
there are a couple of ASoC core fixes (DAI lookup and lockdep stuff)
and usual HD-audio quirks"
* tag 'sound-5.9-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (23 commits)
ALSA: hda/realtek - The Mic on a RedmiBook doesn't work
ASoC: tlv320adcx140: Wake up codec before accessing register
ASoC: core: Do not cleanup uninitialized dais on soc_pcm_open failure
ALSA: hda: fixup headset for ASUS GX502 laptop
ASoC: Intel: bytcr_rt5640: Add quirk for MPMAN Converter9 2-in-1
ASoC: Intel: haswell: Fix power transition refactor
ASoC: tlv320adcx140: Fix accessing uninitialized adcx140->dev
ASoC: wm8994: Ensure the device is resumed in wm89xx_mic_detect functions
ASoC: wm8994: Skip setting of the WM8994_MICBIAS register for WM1811
ASoC: meson: axg-toddr: fix channel order on g12 platforms
ASoC: soc-core: add snd_soc_find_dai_with_mutex()
ASoC: qcom: common: Fix refcount imbalance on error
ASoC: rt700: Fix return check for devm_regmap_init_sdw()
ASoC: rt715: Fix return check for devm_regmap_init_sdw()
ASoC: rt711: Fix return check for devm_regmap_init_sdw()
ASoC: rt1308-sdw: Fix return check for devm_regmap_init_sdw()
ASoC: max98373: Fix return check for devm_regmap_init_sdw()
ASoC: ti: fixup ams_delta_mute() function name
ASoC: pcm3168a: ignore 0 Hz settings
ASoC: Intel: tgl_max98373: fix a runtime pm issue in multi-thread case
...
|
|
Since kprobe_event= cmdline option allows user to put kprobes on the
functions in initmem, kprobe has to make such probes gone after boot.
Currently the probes on the init functions in modules will be handled
by module callback, but the kernel init text isn't handled.
Without this, kprobes may access non-exist text area to disable or
remove it.
Link: https://lkml.kernel.org/r/159972810544.428528.1839307531600646955.stgit@devnote2
Fixes: 970988e19eb0 ("tracing/kprobe: Add kprobe_event= boot parameter")
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Shuah Khan <skhan@linuxfoundation.org>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
|
|
Commit 32927393dc1c ("sysctl: pass kernel pointers to ->proc_handler")
changed ctl_table.proc_handler to take a kernel pointer. Adjust the
signature of ftrace_enable_sysctl to match ctl_table.proc_handler which
fixes the following sparse warning:
kernel/trace/ftrace.c:7544:43: warning: incorrect type in argument 3 (different address spaces)
kernel/trace/ftrace.c:7544:43: expected void *
kernel/trace/ftrace.c:7544:43: got void [noderef] __user *buffer
Link: https://lkml.kernel.org/r/20200907093207.13540-1-tklauser@distanz.ch
Fixes: 32927393dc1c ("sysctl: pass kernel pointers to ->proc_handler")
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
|
|
Tunnel offload info code uses ETHTOOL_MSG_TUNNEL_INFO_GET message type (cmd
field in genetlink header) for replies to tunnel info netlink request, i.e.
the same value as the request have. This is a problem because we are using
two separate enums for userspace to kernel and kernel to userspace message
types so that this ETHTOOL_MSG_TUNNEL_INFO_GET (28) collides with
ETHTOOL_MSG_CABLE_TEST_TDR_NTF which is what message type 28 means for
kernel to userspace messages.
As the tunnel info request reached mainline in 5.9 merge window, we should
still be able to fix the reply message type without breaking backward
compatibility.
Fixes: c7d759eb7b12 ("ethtool: add tunnel info interface")
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 2a9127fcf229 ("mm: rewrite wait_on_page_bit_common() logic") made
the page locking entirely fair, in that if a waiter came in while the
lock was held, the lock would be transferred to the lockers strictly in
order.
That was intended to finally get rid of the long-reported watchdog
failures that involved the page lock under extreme load, where a process
could end up waiting essentially forever, as other page lockers stole
the lock from under it.
It also improved some benchmarks, but it ended up causing huge
performance regressions on others, simply because fair lock behavior
doesn't end up giving out the lock as aggressively, causing better
worst-case latency, but potentially much worse average latencies and
throughput.
Instead of reverting that change entirely, this introduces a controlled
amount of unfairness, with a sysctl knob to tune it if somebody needs
to. But the default value should hopefully be good for any normal load,
allowing a few rounds of lock stealing, but enforcing the strict
ordering before the lock has been stolen too many times.
There is also a hint from Matthieu Baerts that the fair page coloring
may end up exposing an ABBA deadlock that is hidden by the usual
optimistic lock stealing, and while the unfairness doesn't fix the
fundamental issue (and I'm still looking at that), it avoids it in
practice.
The amount of unfairness can be modified by writing a new value to the
'sysctl_page_lock_unfairness' variable (default value of 5, exposed
through /proc/sys/vm/page_lock_unfairness), but that is hopefully
something we'd use mainly for debugging rather than being necessary for
any deep system tuning.
This whole issue has exposed just how critical the page lock can be, and
how contended it gets under certain locks. And the main contention
doesn't really seem to be anything related to IO (which was the origin
of this lock), but for things like just verifying that the page file
mapping is stable while faulting in the page into a page table.
Link: https://lore.kernel.org/linux-fsdevel/ed8442fd-6f54-dd84-cd4a-941e8b7ee603@MichaelLarabel.com/
Link: https://www.phoronix.com/scan.php?page=article&item=linux-50-59&num=1
Link: https://lore.kernel.org/linux-fsdevel/c560a38d-8313-51fb-b1ec-e904bd8836bc@tessares.net/
Reported-and-tested-by: Michael Larabel <Michael@michaellarabel.com>
Tested-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Chris Mason <clm@fb.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Steal time initialization requires mapping a memory region which
invokes a memory allocation. Doing this at CPU starting time results
in the following trace when CONFIG_DEBUG_ATOMIC_SLEEP is enabled:
BUG: sleeping function called from invalid context at mm/slab.h:498
in_atomic(): 1, irqs_disabled(): 128, non_block: 0, pid: 0, name: swapper/1
CPU: 1 PID: 0 Comm: swapper/1 Not tainted 5.9.0-rc5+ #1
Call trace:
dump_backtrace+0x0/0x208
show_stack+0x1c/0x28
dump_stack+0xc4/0x11c
___might_sleep+0xf8/0x130
__might_sleep+0x58/0x90
slab_pre_alloc_hook.constprop.101+0xd0/0x118
kmem_cache_alloc_node_trace+0x84/0x270
__get_vm_area_node+0x88/0x210
get_vm_area_caller+0x38/0x40
__ioremap_caller+0x70/0xf8
ioremap_cache+0x78/0xb0
memremap+0x9c/0x1a8
init_stolen_time_cpu+0x54/0xf0
cpuhp_invoke_callback+0xa8/0x720
notify_cpu_starting+0xc8/0xd8
secondary_start_kernel+0x114/0x180
CPU1: Booted secondary processor 0x0000000001 [0x431f0a11]
However we don't need to initialize steal time at CPU starting time.
We can simply wait until CPU online time, just sacrificing a bit of
accuracy by returning zero for steal time until we know better.
While at it, add __init to the functions that are only called by
pv_time_init() which is __init.
Signed-off-by: Andrew Jones <drjones@redhat.com>
Fixes: e0685fa228fd ("arm64: Retrieve stolen time as paravirtualized guest")
Cc: stable@vger.kernel.org
Reviewed-by: Steven Price <steven.price@arm.com>
Link: https://lore.kernel.org/r/20200916154530.40809-1-drjones@redhat.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Some drivers have to do significant work, some of which relies on RCU
still being active. Instead of using RCU_NONIDLE in the drivers and
flipping RCU back on, allow drivers to take over RCU-idle duty.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The __this_cpu*() accessors are (in general) IRQ-unsafe which, given
that percpu-rwsem is a blocking primitive, should be just fine.
However, file_end_write() is used from IRQ context and will cause
load-store issues on architectures where the per-cpu accessors are not
natively irq-safe.
Fix it by using the IRQ-safe this_cpu_*() for operations on
read_count. This will generate more expensive code on a number of
platforms, which might cause a performance regression for some of the
other percpu-rwsem users.
If any such is reported, we can consider alternative solutions.
Fixes: 70fe2f48152e ("aio: fix freeze protection of aio writes")
Signed-off-by: Hou Tao <houtao1@huawei.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Will Deacon <will@kernel.org>
Acked-by: Oleg Nesterov <oleg@redhat.com>
Link: https://lkml.kernel.org/r/20200915140750.137881-1-houtao1@huawei.com
|
|
Fix the port-lock initialisation regression introduced by commit
a3cb39d258ef ("serial: core: Allow detach and attach serial device for
console") by making sure that the lock is again initialised during
console setup.
The console may be registered before the serial controller has been
probed in which case the port lock needs to be initialised during
console setup by a call to uart_set_options(). The console-detach
changes introduced a regression in several drivers by effectively
removing that initialisation by not initialising the lock when the port
is used as a console (which is always the case during console setup).
Add back the early lock initialisation and instead use a new
console-reinit flag to handle the case where a console is being
re-attached through sysfs.
The question whether the console-detach interface should have been added
in the first place is left for another discussion.
Note that the console-enabled check in uart_set_options() is not
redundant because of kgdboc, which can end up reinitialising an already
enabled console (see commit 42b6a1baa3ec ("serial_core: Don't
re-initialize a previously initialized spinlock.")).
Fixes: a3cb39d258ef ("serial: core: Allow detach and attach serial device for console")
Cc: stable <stable@vger.kernel.org> # 5.7
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200909143101.15389-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
As we can see from vxlan_build/parse_gbp_hdr(), when processing metadata
on vxlan rx/tx path, only dont_learn/policy_applied/policy_id fields can
be set to or parse from the packet for vxlan gbp option.
So we'd better do the mask when set it in act_tunnel_key and cls_flower.
Otherwise, when users don't know these bits, they may configure with a
value which can never be matched.
Reported-by: Shuang Li <shuali@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
flowi4_multipath_hash was added by the commit referenced below for
tunnels. Unfortunately, the patch did not initialize the new field
for several fast path lookups that do not initialize the entire flow
struct to 0. Fix those locations. Currently, flowi4_multipath_hash
is random garbage and affects the hash value computed by
fib_multipath_hash for multipath selection.
Fixes: 24ba14406c5c ("route: Add multipath_hash in flowi_common to make user-define hash")
Signed-off-by: David Ahern <dsahern@gmail.com>
Cc: wenxu <wenxu@ucloud.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg KH:
"Here are some small driver core and debugfs fixes for 5.9-rc5
Included in here are:
- firmware loader memory leak fix
- firmware loader testing fixes for non-EFI systems
- device link locking fixes found by lockdep
- kobject_del() bugfix that has been affecting some callers
- debugfs minor fix
All of these have been in linux-next for a while with no reported
issues"
* tag 'driver-core-5.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
test_firmware: Test platform fw loading on non-EFI systems
PM: <linux/device.h>: fix @em_pd kernel-doc warning
kobject: Drop unneeded conditional in __kobject_del()
driver core: Fix device_pm_lock() locking for device links
MAINTAINERS: Add the security document to SECURITY CONTACT
driver code: print symbolic error code
debugfs: Fix module state check condition
kobject: Restore old behaviour of kobject_del(NULL)
firmware_loader: fix memory leak for paged buffer
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char / misc driver fixes from Greg KH:
"Here are a number of small driver fixes for 5.9-rc5
Included in here are:
- habanalabs driver fixes
- interconnect driver fixes
- soundwire driver fixes
- dyndbg fixes for reported issues, and then reverts to fix it all up
to a sane state.
- phy driver fixes
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-5.9-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
Revert "dyndbg: accept query terms like file=bar and module=foo"
Revert "dyndbg: fix problem parsing format="foo bar""
scripts/tags.sh: exclude tools directory from tags generation
video: fbdev: fix OOB read in vga_8planes_imageblit()
dyndbg: fix problem parsing format="foo bar"
dyndbg: refine export, rename to dynamic_debug_exec_queries()
dyndbg: give %3u width in pr-format, cosmetic only
interconnect: qcom: Fix small BW votes being truncated to zero
soundwire: fix double free of dangling pointer
interconnect: Show bandwidth for disabled paths as zero in debugfs
habanalabs: fix report of RAZWI initiator coordinates
habanalabs: prevent user buff overflow
phy: omap-usb2-phy: disable PHY charger detect
phy: qcom-qmp: Use correct values for ipq8074 PCIe Gen2 PHY init
soundwire: bus: fix typo in comment on INTSTAT registers
phy: qualcomm: fix return value check in qcom_ipq806x_usb_phy_probe()
phy: qualcomm: fix platform_no_drv_owner.cocci warnings
|
|
Pull kvm fixes from Paolo Bonzini:
"A bit on the bigger side, mostly due to me being on vacation, then
busy, then on parental leave, but there's nothing worrisome.
ARM:
- Multiple stolen time fixes, with a new capability to match x86
- Fix for hugetlbfs mappings when PUD and PMD are the same level
- Fix for hugetlbfs mappings when PTE mappings are enforced (dirty
logging, for example)
- Fix tracing output of 64bit values
x86:
- nSVM state restore fixes
- Async page fault fixes
- Lots of small fixes everywhere"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (25 commits)
KVM: emulator: more strict rsm checks.
KVM: nSVM: more strict SMM checks when returning to nested guest
SVM: nSVM: setup nested msr permission bitmap on nested state load
SVM: nSVM: correctly restore GIF on vmexit from nesting after migration
x86/kvm: don't forget to ACK async PF IRQ
x86/kvm: properly use DEFINE_IDTENTRY_SYSVEC() macro
KVM: VMX: Don't freeze guest when event delivery causes an APIC-access exit
KVM: SVM: avoid emulation with stale next_rip
KVM: x86: always allow writing '0' to MSR_KVM_ASYNC_PF_EN
KVM: SVM: Periodically schedule when unregistering regions on destroy
KVM: MIPS: Change the definition of kvm type
kvm x86/mmu: use KVM_REQ_MMU_SYNC to sync when needed
KVM: nVMX: Fix the update value of nested load IA32_PERF_GLOBAL_CTRL control
KVM: fix memory leak in kvm_io_bus_unregister_dev()
KVM: Check the allocation of pv cpu mask
KVM: nVMX: Update VMCS02 when L2 PAE PDPTE updates detected
KVM: arm64: Update page shift if stage 2 block mapping not supported
KVM: arm64: Fix address truncation in traces
KVM: arm64: Do not try to map PUDs when they are folded into PMD
arm64/x86: KVM: Introduce steal-time cap
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
"Usual driver bugfixes for the I2C subsystem"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: algo: pca: Reapply i2c bus settings after reset
i2c: npcm7xx: Fix timeout calculation
misc: eeprom: at24: register nvmem only after eeprom is ready to use
|
|
MIPS defines two kvm types:
#define KVM_VM_MIPS_TE 0
#define KVM_VM_MIPS_VZ 1
In Documentation/virt/kvm/api.rst it is said that "You probably want to
use 0 as machine type", which implies that type 0 be the "automatic" or
"default" type. And, in user-space libvirt use the null-machine (with
type 0) to detect the kvm capability, which returns "KVM not supported"
on a VZ platform.
I try to fix it in QEMU but it is ugly:
https://lists.nongnu.org/archive/html/qemu-devel/2020-08/msg05629.html
And Thomas Huth suggests me to change the definition of kvm type:
https://lists.nongnu.org/archive/html/qemu-devel/2020-09/msg03281.html
So I define like this:
#define KVM_VM_MIPS_AUTO 0
#define KVM_VM_MIPS_VZ 1
#define KVM_VM_MIPS_TE 2
Since VZ and TE cannot co-exists, using type 0 on a TE platform will
still return success (so old user-space tools have no problems on new
kernels); the advantage is that using type 0 on a VZ platform will not
return failure. So, the only problem is "new user-space tools use type
2 on old kernels", but if we treat this as a kernel bug, we can backport
this patch to old stable kernels.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Message-Id: <1599734031-28746-1-git-send-email-chenhc@lemote.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
* powercap:
powercap: make documentation reflect code
powercap/intel_rapl: add support for AlderLake
powercap/intel_rapl: add support for RocketLake
powercap/intel_rapl: add support for TigerLake Desktop
|
|
There is no @validate argument.
CC: Johannes Berg <johannes.berg@intel.com>
Fixes: 3de644035446 ("netlink: re-add parse/validate functions in strict mode")
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove the weird space inside the NETIF_F_CSUM_MASK.
Signed-off-by: Miaohe Lin <linmiaohe@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix up the documentation of the struct powercap_control_type members
to match the code.
Also fixup stray whitespace.
Signed-off-by: Amit Kucheria <amitk@kernel.org>
[ rjw: Changelog edits ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Fix kernel-doc warning in <linux/device.h>:
../include/linux/device.h:613: warning: Function parameter or member 'em_pd' not described in 'device'
Fixes: 1bc138c62295 ("PM / EM: add support for other devices than CPUs in Energy Model")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
On non-EFI systems, it wasn't possible to test the platform firmware
loader because it will have never set "checked_fw" during __init.
Instead, allow the test code to override this check. Additionally split
the declarations into a private symbol namespace so there is greater
enforcement of the symbol visibility.
Fixes: 548193cba2a7 ("test_firmware: add support for firmware_request_platform")
Cc: stable@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20200909225354.3118328-1-keescook@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In CMT and NPAR the PF is unknown when the GFS block processes the
packet. Therefore cannot use searcher as it has a per PF database,
and thus ARFS must be disabled.
Fixes: d51e4af5c209 ("qed: aRFS infrastructure support")
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
skb_put_padto() and __skb_put_padto() callers
must check return values or risk use-after-free.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If something goes wrong (such as the SCL being stuck low) then we need
to reset the PCA chip. The issue with this is that on reset we lose all
config settings and the chip ends up in a disabled state which results
in a lock up/high CPU usage. We need to re-apply any configuration that
had previously been set and re-enable the chip.
Signed-off-by: Evan Nimmo <evan.nimmo@alliedtelesis.co.nz>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
On x86_64, each notification results in one skbuff allocation which
consumes at least 768 bytes due to the skbuff overhead.
This patch coalesces several notifications into one single skbuff, so
each notification consumes at least ~211 bytes, that ~3.5 times less
memory consumption. As a result, this is reducing the chances to exhaust
the netlink socket receive buffer.
Rule of thumb is that each notification batch only contains netlink
messages whose report flag is the same, nfnetlink_send() requires this
to do appropriate delivery to userspace, either via unicast (echo
mode) or multicast (monitor mode).
The skbuff control buffer is used to annotate the report flag for later
handling at the new coalescing routine.
The batch skbuff notification size is NLMSG_GOODSIZE, using a larger
skbuff would allow for more socket receiver buffer savings (to amortize
the cost of the skbuff even more), however, going over that size might
break userspace applications, so let's be conservative and stick to
NLMSG_GOODSIZE.
Reported-by: Phil Sutter <phil@nwl.cc>
Acked-by: Phil Sutter <phil@nwl.cc>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Fix kernel-doc warning in <linux/netdevice.h>:
../include/linux/netdevice.h:2158: warning: Function parameter or member 'xdp_state' not described in 'net_device'
Fixes: 7f0a838254bd ("bpf, xdp: Maintain info on attached XDP BPF programs in net_device")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Andrii Nakryiko <andriin@fb.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix kernel-doc warning in <linux/netdevice.h>:
../include/linux/netdevice.h:2158: warning: Function parameter or member 'proto_down_reason' not described in 'net_device'
Fixes: 829eb208e80d ("rtnetlink: add support for protodown reason")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix kernel-doc warning in <linux/device.h>:
../include/linux/device.h:613: warning: Function parameter or member 'em_pd' not described in 'device'
Fixes: 1bc138c62295 ("PM / EM: add support for other devices than CPUs in Energy Model")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Link: https://lore.kernel.org/r/d97f40ad-3033-703a-c3cb-2843ce0f6371@infradead.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Introduce for_each_rtd_dais_rollback macro which behaves exactly like
for_each_codec_dais_rollback and its cpu_dais equivalent but for all
dais instead.
Use newly added macro to fix soc_pcm_open error path and prevent
uninitialized dais from being cleaned-up.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Fixes: 5d9fa03e6c35 ("ASoC: soc-pcm: tidyup soc_pcm_open() order")
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/20200907111939.16169-1-cezary.rojewski@intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
- more generic entry code ABI fallout
- debug register handling bugfixes
- fix vmalloc mappings on 32-bit kernels
- kprobes instrumentation output fix on 32-bit kernels
- fix over-eager WARN_ON_ONCE() on !SMAP hardware
- NUMA debugging fix
- fix Clang related crash on !RETPOLINE kernels
* tag 'x86-urgent-2020-09-06' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/entry: Unbreak 32bit fast syscall
x86/debug: Allow a single level of #DB recursion
x86/entry: Fix AC assertion
tracing/kprobes, x86/ptrace: Fix regs argument order for i386
x86, fakenuma: Fix invalid starting node ID
x86/mm/32: Bring back vmalloc faulting on x86_32
x86/cmdline: Disable jump tables for cmdline.c
|
