Age | Commit message (Collapse) | Author |
|
commit 2c8f8afa7f92 ("mtd: nand: add generic helpers to check,
match, maximize ECC settings") provides generic helpers which
drivers can use for setting up ECC parameters.
Since same board can have different ECC strength nand chips so
following is the logic for setting up ECC strength and ECC step
size, which can be used by most of the drivers.
1. If both ECC step size and ECC strength are already set
(usually by DT) then just check whether this setting
is supported by NAND controller.
2. If NAND_ECC_MAXIMIZE is set, then select maximum ECC strength
supported by NAND controller.
3. Otherwise, try to match the ECC step size and ECC strength closest
to the chip's requirement. If available OOB size can't fit the chip
requirement then select maximum ECC strength which can be fit with
available OOB size.
This patch introduces nand_ecc_choose_conf function which calls the
required helper functions for the above logic. The drivers can use
this single function instead of calling the 3 helper functions
individually.
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Add defines for the ONFI version bits and use them in
nand_flash_detect_onfi().
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
This is called after the ONFI parameter page checksum is verified
and allows us to override the contents of the parameter page.
Suggested-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Allow to define a NAND chip as a boot device. This can be helpful
for the selection of the ECC algorithm and strength in case the boot
ROM supports only a subset of controller provided options.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Add Reed-Solomon (RS) to the enumeration of ECC algorithms.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/IIO fixes from Greg KH:
"Here are a few small staging and IIO driver fixes for 4.18-rc3.
Nothing major or big, all just fixes for reported problems since
4.18-rc1. All of these have been in linux-next this week with no
reported problems"
* tag 'staging-4.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: android: ion: Return an ERR_PTR in ion_map_kernel
staging: comedi: quatech_daqp_cs: fix no-op loop daqp_ao_insn_write()
iio: imu: inv_mpu6050: Fix probe() failure on older ACPI based machines
iio: buffer: fix the function signature to match implementation
iio: mma8452: Fix ignoring MMA8452_INT_DRDY
iio: tsl2x7x/tsl2772: avoid potential division by zero
iio: pressure: bmp280: fix relative humidity unit
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here is a number of USB gadget and other driver fixes for 4.18-rc3.
There's a bunch of them here, most of them being gadget driver and
xhci host controller fixes for reported issues (as normal), but there
are also some new device ids, and some fixes for the typec code.
There is an acpi core patch in here that was acked by the acpi
maintainer as it is needed for the typec fixes in order to properly
solve a problem in that driver.
All of these have been in linux-next this week with no reported
issues"
* tag 'usb-4.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (33 commits)
usb: chipidea: host: fix disconnection detect issue
usb: typec: tcpm: fix logbuffer index is wrong if _tcpm_log is re-entered
typec: tcpm: Fix a msecs vs jiffies bug
NFC: pn533: Fix wrong GFP flag usage
usb: cdc_acm: Add quirk for Uniden UBC125 scanner
staging/typec: fix tcpci_rt1711h build errors
usb: typec: ucsi: Fix for incorrect status data issue
usb: typec: ucsi: acpi: Workaround for cache mode issue
acpi: Add helper for deactivating memory region
usb: xhci: increase CRS timeout value
usb: xhci: tegra: fix runtime PM error handling
usb: xhci: remove the code build warning
xhci: Fix kernel oops in trace_xhci_free_virt_device
xhci: Fix perceived dead host due to runtime suspend race with event handler
dwc2: gadget: Fix ISOC IN DDMA PID bitfield value calculation
usb: gadget: dwc2: fix memory leak in gadget_init()
usb: gadget: composite: fix delayed_status race condition when set_interface
usb: dwc2: fix isoc split in transfer with no data
usb: dwc2: alloc dma aligned buffer for isoc split in
usb: dwc2: fix the incorrect bitmaps for the ports of multi_tt hub
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild fixes from Masahiro Yamada:
- introduce __diag_* macros and suppress -Wattribute-alias warnings
from GCC 8
- fix stack protector test script for x86_64
- fix line number handling in Kconfig
- document that '#' starts a comment in Kconfig
- handle P_SYMBOL property in dump debugging of Kconfig
- correct help message of LD_DEAD_CODE_DATA_ELIMINATION
- fix occasional segmentation faults in Kconfig
* tag 'kbuild-fixes-v4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
kconfig: loop boundary condition fix
kbuild: reword help of LD_DEAD_CODE_DATA_ELIMINATION
kconfig: handle P_SYMBOL in print_symbol()
kconfig: document Kconfig source file comments
kconfig: fix line numbers for if-entries in menu tree
stack-protector: Fix test with 32-bit userland and CONFIG_64BIT=y
powerpc: Remove -Wattribute-alias pragmas
disable -Wattribute-alias warning for SYSCALL_DEFINEx()
kbuild: add macro for controlling warnings to linux/compiler.h
|
|
Pull block fixes from Jens Axboe:
"Small set of fixes for this series. Mostly just minor fixes, the only
oddball in here is the sg change.
The sg change came out of the stall fix for NVMe, where we added a
mempool and limited us to a single page allocation. CONFIG_SG_DEBUG
sort-of ruins that, since we'd need to account for that. That's
actually a generic problem, since lots of drivers need to allocate SG
lists. So this just removes support for CONFIG_SG_DEBUG, which I added
back in 2007 and to my knowledge it was never useful.
Anyway, outside of that, this pull contains:
- clone of request with special payload fix (Bart)
- drbd discard handling fix (Bart)
- SATA blk-mq stall fix (me)
- chunk size fix (Keith)
- double free nvme rdma fix (Sagi)"
* tag 'for-linus-20180629' of git://git.kernel.dk/linux-block:
sg: remove ->sg_magic member
drbd: Fix drbd_request_prepare() discard handling
blk-mq: don't queue more if we get a busy return
block: Fix cloning of requests with a special payload
nvme-rdma: fix possible double free of controller async event buffer
block: Fix transfer when chunk sectors exceeds max
|
|
This was introduced more than a decade ago when sg chaining was
added, but we never really caught anything with it. The scatterlist
entry size can be critical, since drivers allocate it, so remove
the magic member. Recently it's been triggering allocation stalls
and failures in NVMe.
Tested-by: Jordan Glover <Golden_Miller83@protonmail.ch>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix up recently added features (the Kryo cpufreq driver and
performance states coverage in the generic power domains framework),
add missing documentation for a recently added sysfs knob in the
intel_pstate driver and fix an error in its documentation.
Specifics:
- Fix the initialization time error handling in the recently added
Kryo cpufreq driver (Dan Carpenter).
- Fix up the recently added coverage of performance states in the
generic power domains (genpd) framework (Viresh Kumar).
- Add missing documentation of the new hwp_dynamic_boost sysfs knob
in the intel_pstate driver (Rafael Wysocki).
- Fix incorrect sysfs path in the intel_pstate driver documentation
(Rafael Wysocki)"
* tag 'pm-4.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
Documentation: intel_pstate: Describe hwp_dynamic_boost sysfs knob
Documentation: admin-guide: intel_pstate: Fix sysfs path
PM / Domains: Rename opp_node to np
PM / Domains: Fix return value of of_genpd_opp_to_performance_state()
cpufreq: qcom-kryo: Fix error handling in probe()
|
|
io_pgetevents() will not change the signal mask. Mark it const to make
it clear and to reduce the need for casts in user code.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Avi Kivity <avi@scylladb.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
[hch: reapply the patch that got incorrectly reverted]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Merge fixes from Andrew Morton:
"7 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
proc: add Alexey to MAINTAINERS
kasan: depend on CONFIG_SLUB_DEBUG
include/linux/dax.h: dax_iomap_fault() returns vm_fault_t
x86/e820: put !E820_TYPE_RAM regions into memblock.reserved
slub: fix failure when we delete and create a slab cache
Revert mm/vmstat.c: fix vmstat_update() preemption BUG
lib/percpu_ida.c: don't do alloc from per-CPU list if there is none
|
|
Commit 1c8f422059ae ("mm: change return type to vm_fault_t") missed a
conversion. It's not a big problem at present because mainline is still
using
typedef int vm_fault_t;
Fixes: 1c8f422059ae ("mm: change return type to vm_fault_t")
Link: http://lkml.kernel.org/r/20180620172046.GA27894@jordon-HP-15-Notebook-PC
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
In kernel 4.17 I removed some code from dm-bufio that did slab cache
merging (commit 21bb13276768: "dm bufio: remove code that merges slab
caches") - both slab and slub support merging caches with identical
attributes, so dm-bufio now just calls kmem_cache_create and relies on
implicit merging.
This uncovered a bug in the slub subsystem - if we delete a cache and
immediatelly create another cache with the same attributes, it fails
because of duplicate filename in /sys/kernel/slab/. The slub subsystem
offloads freeing the cache to a workqueue - and if we create the new
cache before the workqueue runs, it complains because of duplicate
filename in sysfs.
This patch fixes the bug by moving the call of kobject_del from
sysfs_slab_remove_workfn to shutdown_cache. kobject_del must be called
while we hold slab_mutex - so that the sysfs entry is deleted before a
cache with the same attributes could be created.
Running device-mapper-test-suite with:
dmtest run --suite thin-provisioning -n /commit_failure_causes_fallback/
triggered:
Buffer I/O error on dev dm-0, logical block 1572848, async page read
device-mapper: thin: 253:1: metadata operation 'dm_pool_alloc_data_block' failed: error = -5
device-mapper: thin: 253:1: aborting current metadata transaction
sysfs: cannot create duplicate filename '/kernel/slab/:a-0000144'
CPU: 2 PID: 1037 Comm: kworker/u48:1 Not tainted 4.17.0.snitm+ #25
Hardware name: Supermicro SYS-1029P-WTR/X11DDW-L, BIOS 2.0a 12/06/2017
Workqueue: dm-thin do_worker [dm_thin_pool]
Call Trace:
dump_stack+0x5a/0x73
sysfs_warn_dup+0x58/0x70
sysfs_create_dir_ns+0x77/0x80
kobject_add_internal+0xba/0x2e0
kobject_init_and_add+0x70/0xb0
sysfs_slab_add+0xb1/0x250
__kmem_cache_create+0x116/0x150
create_cache+0xd9/0x1f0
kmem_cache_create_usercopy+0x1c1/0x250
kmem_cache_create+0x18/0x20
dm_bufio_client_create+0x1ae/0x410 [dm_bufio]
dm_block_manager_create+0x5e/0x90 [dm_persistent_data]
__create_persistent_data_objects+0x38/0x940 [dm_thin_pool]
dm_pool_abort_metadata+0x64/0x90 [dm_thin_pool]
metadata_operation_failed+0x59/0x100 [dm_thin_pool]
alloc_data_block.isra.53+0x86/0x180 [dm_thin_pool]
process_cell+0x2a3/0x550 [dm_thin_pool]
do_worker+0x28d/0x8f0 [dm_thin_pool]
process_one_work+0x171/0x370
worker_thread+0x49/0x3f0
kthread+0xf8/0x130
ret_from_fork+0x35/0x40
kobject_add_internal failed for :a-0000144 with -EEXIST, don't try to register things with the same name in the same directory.
kmem_cache_create(dm_bufio_buffer-16) failed with error -17
Link: http://lkml.kernel.org/r/alpine.LRH.2.02.1806151817130.6333@file01.intranet.prod.int.rdu2.redhat.com
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Reported-by: Mike Snitzer <snitzer@redhat.com>
Tested-by: Mike Snitzer <snitzer@redhat.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The poll() changes were not well thought out, and completely
unexplained. They also caused a huge performance regression, because
"->poll()" was no longer a trivial file operation that just called down
to the underlying file operations, but instead did at least two indirect
calls.
Indirect calls are sadly slow now with the Spectre mitigation, but the
performance problem could at least be largely mitigated by changing the
"->get_poll_head()" operation to just have a per-file-descriptor pointer
to the poll head instead. That gets rid of one of the new indirections.
But that doesn't fix the new complexity that is completely unwarranted
for the regular case. The (undocumented) reason for the poll() changes
was some alleged AIO poll race fixing, but we don't make the common case
slower and more complex for some uncommon special case, so this all
really needs way more explanations and most likely a fundamental
redesign.
[ This revert is a revert of about 30 different commits, not reverted
individually because that would just be unnecessarily messy - Linus ]
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Three small bug fixes (barrier elimination, memory leak on unload,
spinlock recursion) and a technical enhancement left over from the
merge window: the TCMU read length support is required for tape
devices read when the length of the read is greater than the tape
block size"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: scsi_debug: Fix memory leak on module unload
scsi: qla2xxx: Spinlock recursion in qla_target
scsi: ipr: Eliminate duplicate barriers
scsi: target: tcmu: add read length support
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input updates from Dmitry Torokhov:
- the main change is a fix for my brain-dead patch to PS/2 button
reporting for some protocols that made it in 4.17
- there is a new driver for Spreadtum vibrator that I intended to send
during merge window but ended up not sending the 2nd pull request.
Given that this is a brand new driver we should not see regressions
here
- a fixup to Elantech PS/2 driver to avoid decoding errors on Thinkpad
P52
- addition of few more ACPI IDs for Silead and Elan drivers
- RMI4 is switched to using IRQ domain code instead of rolling its own
implementation
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: psmouse - fix button reporting for basic protocols
Input: xpad - fix GPD Win 2 controller name
Input: elan_i2c_smbus - fix more potential stack buffer overflows
Input: elan_i2c - add ELAN0618 (Lenovo v330 15IKB) ACPI ID
Input: elantech - fix V4 report decoding for module with middle key
Input: elantech - enable middle button of touchpads on ThinkPad P52
Input: do not assign new tracking ID when changing tool type
Input: make input_report_slot_state() return boolean
Input: synaptics-rmi4 - fix axis-swap behavior
Input: synaptics-rmi4 - fix the error return code in rmi_probe_interrupts()
Input: synaptics-rmi4 - convert irq distribution to irq_domain
Input: silead - add MSSL0002 ACPI HID
Input: goldfish_events - fix checkpatch warnings
Input: add Spreadtrum vibrator driver
|
|
A device may have boundary restrictions where the number of sectors
between boundaries exceeds its max transfer size. In this case, we need
to cap the max size to the smaller of the two limits.
Reported-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Tested-by: Jitendra Bhivare <jitendra.bhivare@broadcom.com>
Cc: <stable@vger.kernel.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First set of IIO fixes for the 4.18 cycle.
* bmp280
- Fix wrong relative humidity unit.
* buffer
- Fix a function signature to match the function.
* inv_mpu6050
- Fix a regression in which older ACPI devices won't have working
interrupts due to lack of information on the interrupt type.
* mma8452
- Don't ignore data ready interrupt when handling interrupts as will
look like an unhandled interrupt.
* tsl2x7x/tsl2772
- Avoid a potential division by zero.
|
|
gcc-8 warns for every single definition of a system call entry
point, e.g.:
include/linux/compat.h:56:18: error: 'compat_sys_rt_sigprocmask' alias between functions of incompatible types 'long int(int, compat_sigset_t *, compat_sigset_t *, compat_size_t)' {aka 'long int(int, struct <anonymous> *, struct <anonymous> *, unsigned int)'} and 'long int(long int, long int, long int, long int)' [-Werror=attribute-alias]
asmlinkage long compat_sys##name(__MAP(x,__SC_DECL,__VA_ARGS__))\
^~~~~~~~~~
include/linux/compat.h:45:2: note: in expansion of macro 'COMPAT_SYSCALL_DEFINEx'
COMPAT_SYSCALL_DEFINEx(4, _##name, __VA_ARGS__)
^~~~~~~~~~~~~~~~~~~~~~
kernel/signal.c:2601:1: note: in expansion of macro 'COMPAT_SYSCALL_DEFINE4'
COMPAT_SYSCALL_DEFINE4(rt_sigprocmask, int, how, compat_sigset_t __user *, nset,
^~~~~~~~~~~~~~~~~~~~~~
include/linux/compat.h:60:18: note: aliased declaration here
asmlinkage long compat_SyS##name(__MAP(x,__SC_LONG,__VA_ARGS__))\
^~~~~~~~~~
The new warning seems reasonable in principle, but it doesn't
help us here, since we rely on the type mismatch to sanitize the
system call arguments. After I reported this as GCC PR82435, a new
-Wno-attribute-alias option was added that could be used to turn the
warning off globally on the command line, but I'd prefer to do it a
little more fine-grained.
Interestingly, turning a warning off and on again inside of
a single macro doesn't always work, in this case I had to add
an extra statement inbetween and decided to copy the __SC_TEST
one from the native syscall to the compat syscall macro. See
https://gcc.gnu.org/bugzilla/show_bug.cgi?id=83256 for more details
about this.
[paul.burton@mips.com:
- Rebase atop current master.
- Split GCC & version arguments to __diag_ignore() in order to match
changes to the preceding patch.
- Add the comment argument to match the preceding patch.]
Link: https://gcc.gnu.org/bugzilla/show_bug.cgi?id=82435
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Tested-by: Christophe Leroy <christophe.leroy@c-s.fr>
Tested-by: Stafford Horne <shorne@gmail.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
I have occasionally run into a situation where it would make sense to
control a compiler warning from a source file rather than doing so from
a Makefile using the $(cc-disable-warning, ...) or $(cc-option, ...)
helpers.
The approach here is similar to what glibc uses, using __diag() and
related macros to encapsulate a _Pragma("GCC diagnostic ...") statement
that gets turned into the respective "#pragma GCC diagnostic ..." by
the preprocessor when the macro gets expanded.
Like glibc, I also have an argument to pass the affected compiler
version, but decided to actually evaluate that one. For now, this
supports GCC_4_6, GCC_4_7, GCC_4_8, GCC_4_9, GCC_5, GCC_6, GCC_7,
GCC_8 and GCC_9. Adding support for CLANG_5 and other interesting
versions is straightforward here. GNU compilers starting with gcc-4.2
could support it in principle, but "#pragma GCC diagnostic push"
was only added in gcc-4.6, so it seems simpler to not deal with those
at all. The same versions show a large number of warnings already,
so it seems easier to just leave it at that and not do a more
fine-grained control for them.
The use cases I found so far include:
- turning off the gcc-8 -Wattribute-alias warning inside of the
SYSCALL_DEFINEx() macro without having to do it globally.
- Reducing the build time for a simple re-make after a change,
once we move the warnings from ./Makefile and
./scripts/Makefile.extrawarn into linux/compiler.h
- More control over the warnings based on other configurations,
using preprocessor syntax instead of Makefile syntax. This should make
it easier for the average developer to understand and change things.
- Adding an easy way to turn the W=1 option on unconditionally
for a subdirectory or a specific file. This has been requested
by several developers in the past that want to have their subsystems
W=1 clean.
- Integrating clang better into the build systems. Clang supports
more warnings than GCC, and we probably want to classify them
as default, W=1, W=2 etc, but there are cases in which the
warnings should be classified differently due to excessive false
positives from one or the other compiler.
- Adding a way to turn the default warnings into errors (e.g. using
a new "make E=0" tag) while not also turning the W=1 warnings into
errors.
This patch for now just adds the minimal infrastructure in order to
do the first of the list above. As the #pragma GCC diagnostic
takes precedence over command line options, the next step would be
to convert a lot of the individual Makefiles that set nonstandard
options to use __diag() instead.
[paul.burton@mips.com:
- Rebase atop current master.
- Add __diag_GCC, or more generally __diag_<compiler>, abstraction to
avoid code outside of linux/compiler-gcc.h needing to duplicate
knowledge about different GCC versions.
- Add a comment argument to __diag_{ignore,warn,error} which isn't
used in the expansion of the macros but serves to push people to
document the reason for using them - per feedback from Kees Cook.
- Translate severity to GCC-specific pragmas in linux/compiler-gcc.h
rather than using GCC-specific in linux/compiler_types.h.
- Drop all but GCC 8 macros, since we only need to define macros for
versions that we need to introduce pragmas for, and as of this
series that's just GCC 8.
- Capitalize comments in linux/compiler-gcc.h to match the style of
the rest of the file.
- Line up macro definitions with tabs in linux/compiler-gcc.h.]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Tested-by: Christophe Leroy <christophe.leroy@c-s.fr>
Tested-by: Stafford Horne <shorne@gmail.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Sometimes memory resource may be overlapping with
SystemMemory Operation Region by design, for example if the
memory region is used as a mailbox for communication with a
firmware in the system. One occasion of such mailboxes is
USB Type-C Connector System Software Interface (UCSI).
With regions like that, it is important that the driver is
able to map the memory with the requirements it has. For
example, the driver should be allowed to map the memory as
non-cached memory. However, if the operation region has been
accessed before the driver has mapped the memory, the memory
has been marked as write-back by the time the driver is
loaded. That means the driver will fail to map the memory
if it expects non-cached memory.
To work around the problem, introducing helper that the
drivers can use to temporarily deactivate (unmap)
SystemMemory Operation Regions that overlap with their
IO memory.
Fixes: 8243edf44152 ("usb: typec: ucsi: Add ACPI driver")
Cc: stable@vger.kernel.org
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Pull networking fixes from David Miller:
1) Fix netpoll OOPS in r8169, from Ville Syrjälä.
2) Fix bpf instruction alignment on powerpc et al., from Eric Dumazet.
3) Don't ignore IFLA_MTU attribute when creating new ipvlan links. From
Xin Long.
4) Fix use after free in AF_PACKET, from Eric Dumazet.
5) Mis-matched RTNL unlock in xen-netfront, from Ross Lagerwall.
6) Fix VSOCK loopback on big-endian, from Claudio Imbrenda.
7) Missing RX buffer offset correction when computing DMA addresses in
mvneta driver, from Antoine Tenart.
8) Fix crashes in DCCP's ccid3_hc_rx_send_feedback, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (34 commits)
sfc: make function efx_rps_hash_bucket static
strparser: Corrected typo in documentation.
qmi_wwan: add support for the Dell Wireless 5821e module
cxgb4: when disabling dcb set txq dcb priority to 0
net_sched: remove a bogus warning in hfsc
net: dccp: switch rx_tstamp_last_feedback to monotonic clock
net: dccp: avoid crash in ccid3_hc_rx_send_feedback()
net: Remove depends on HAS_DMA in case of platform dependency
MAINTAINERS: Add file patterns for dsa device tree bindings
net: mscc: make sparse happy
net: mvneta: fix the Rx desc DMA address in the Rx path
Documentation: e1000: Fix docs build error
Documentation: e100: Fix docs build error
Documentation: e1000: Use correct heading adornment
Documentation: e100: Use correct heading adornment
ipv6: mcast: fix unsolicited report interval after receiving querys
vhost_net: validate sock before trying to put its fd
VSOCK: fix loopback on big-endian systems
net: ethernet: ti: davinci_cpdma: make function cpdma_desc_pool_create static
xen-netfront: Update features after registering netdev
...
|
|
The DT node passed here isn't necessarily an OPP node, as this routine
can also be used for cases where the "required-opps" property is present
directly in the device's node. Rename it.
This also removes a stale comment.
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
of_genpd_opp_to_performance_state() should return 0 for errors, but the
dummy routine isn't doing that. Fix it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
linux/iio/buffer-dma.h was not updated to when length was changed to
unsigned int.
Fixes: c043ec1ca5ba ("iio:buffer: make length types match kfifo types")
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull rseq fixes from Thomas Gleixer:
"A pile of rseq related fixups:
- Prevent infinite recursion when delivering SIGSEGV
- Remove the abort of rseq critical section on fork() as syscalls
inside rseq critical sections are explicitely forbidden. So no
point in doing the abort on the child.
- Align the rseq structure on 32 bytes in the ARM selftest code.
- Fix file permissions of the test script"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
rseq: Avoid infinite recursion when delivering SIGSEGV
rseq/cleanup: Do not abort rseq c.s. in child on fork()
rseq/selftests/arm: Align 'struct rseq_cs' on 32 bytes
rseq/selftests: Make run_param_test.sh executable
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull core fixes from Thomas Gleixner:
"Two tiny fixes:
- Add the missing machine_real_restart() to objtools noreturn list so
it stops complaining
- Fix a trivial comment typo"
* 'core-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
kernel.h: Fix a typo in comment
objtool: Add machine_real_restart() to the noreturn list
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Thomas Gleixner:
"A set of fixes for x86:
- Make Xen PV guest deal with speculative store bypass correctly
- Address more fallout from the 5-Level pagetable handling. Undo an
__initdata annotation to avoid section mismatch and malfunction
when post init code would touch the freed variable.
- Handle exception fixup in math_error() before calling notify_die().
The reverse call order incorrectly triggers notify_die() listeners
for soemthing which is handled correctly at the site which issues
the floating point instruction.
- Fix an off by one in the LLC topology calculation on AMD
- Handle non standard memory block sizes gracefully un UV platforms
- Plug a memory leak in the microcode loader
- Sanitize the purgatory build magic
- Add the x86 specific device tree bindings directory to the x86
MAINTAINER file patterns"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm: Fix 'no5lvl' handling
Revert "x86/mm: Mark __pgtable_l5_enabled __initdata"
x86/CPU/AMD: Fix LLC ID bit-shift calculation
MAINTAINERS: Add file patterns for x86 device tree bindings
x86/microcode/intel: Fix memleak in save_microcode_patch()
x86/platform/UV: Add kernel parameter to set memory block size
x86/platform/UV: Use new set memory block size function
x86/platform/UV: Add adjustable set memory block size function
x86/build: Remove unnecessary preparation for purgatory
Revert "kexec/purgatory: Add clean-up for purgatory directory"
x86/xen: Add call of speculative_store_bypass_ht_init() to PV paths
x86: Call fixup_exception() before notify_die() in math_error()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking fixes from Thomas Gleixner:
"A set of fixes and updates for the locking code:
- Prevent lockdep from updating irq state within its own code and
thereby confusing itself.
- Buid fix for older GCCs which mistreat anonymous unions
- Add a missing lockdep annotation in down_read_non_onwer() which
causes up_read_non_owner() to emit a lockdep splat
- Remove the custom alpha dec_and_lock() implementation which is
incorrect in terms of ordering and use the generic one.
The remaining two commits are not strictly fixes. They provide irqsave
variants of atomic_dec_and_lock() and refcount_dec_and_lock(). These
are required to merge the relevant updates and cleanups into different
maintainer trees for 4.19, so routing them into mainline without
actual users is the sanest approach.
They should have been in -rc1, but last weekend I took the liberty to
just avoid computers in order to regain some mental sanity"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
locking/qspinlock: Fix build for anonymous union in older GCC compilers
locking/lockdep: Do not record IRQ state within lockdep code
locking/rwsem: Fix up_read_non_owner() warning with DEBUG_RWSEMS
locking/refcounts: Implement refcount_dec_and_lock_irqsave()
atomic: Add irqsave variant of atomic_dec_and_lock()
alpha: Remove custom dec_and_lock() implementation
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
"A set of fixes mostly for the ARM/GIC world:
- Fix the MSI affinity handling in the ls-scfg irq chip driver so it
updates and uses the effective affinity mask correctly
- Prevent binding LPIs to offline CPUs and respect the Cavium erratum
which requires that LPIs which belong to an offline NUMA node are
not bound to a CPU on a different NUMA node.
- Free only the amount of allocated interrupts in the GIC-V2M driver
instead of trying to free log2(nrirqs).
- Prevent emitting SYNC and VSYNC targetting non existing interrupt
collections in the GIC-V3 ITS driver
- Ensure that the GIV-V3 interrupt redistributor is correctly
reprogrammed on CPU hotplug
- Remove a stale unused helper function"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqdesc: Delete irq_desc_get_msi_desc()
irqchip/gic-v3-its: Fix reprogramming of redistributors on CPU hotplug
irqchip/gic-v3-its: Only emit VSYNC if targetting a valid collection
irqchip/gic-v3-its: Only emit SYNC if targetting a valid collection
irqchip/gic-v3-its: Don't bind LPI to unavailable NUMA node
irqchip/gic-v2m: Fix SPI release on error path
irqchip/ls-scfg-msi: Fix MSI affinity handling
genirq/debugfs: Add missing IRQCHIP_SUPPORTS_LEVEL_MSI debug
|
|
Pull block fixes from Jens Axboe:
- Further timeout fixes. We aren't quite there yet, so expect another
round of fixes for that to completely close some of the IRQ vs
completion races. (Christoph/Bart)
- Set of NVMe fixes from the usual suspects, mostly error handling
- Two off-by-one fixes (Dan)
- Another bdi race fix (Jan)
- Fix nbd reconfigure with NBD_DISCONNECT_ON_CLOSE (Doron)
* tag 'for-linus-20180623' of git://git.kernel.dk/linux-block:
blk-mq: Fix timeout handling in case the timeout handler returns BLK_EH_DONE
bdi: Fix another oops in wb_workfn()
lightnvm: Remove depends on HAS_DMA in case of platform dependency
nvme-pci: limit max IO size and segments to avoid high order allocations
nvme-pci: move nvme_kill_queues to nvme_remove_dead_ctrl
nvme-fc: release io queues to allow fast fail
nbd: Add the nbd NBD_DISCONNECT_ON_CLOSE config flag.
block: sed-opal: Fix a couple off by one bugs
blk-mq-debugfs: Off by one in blk_mq_rq_state_name()
nvmet: reset keep alive timer in controller enable
nvme-rdma: don't override opts->queue_size
nvme-rdma: Fix command completion race at error recovery
nvme-rdma: fix possible free of a non-allocated async event buffer
nvme-rdma: fix possible double free condition when failing to create a controller
Revert "block: Add warning for bi_next not NULL in bio_endio()"
block: fix timeout changes for legacy request drivers
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen fixes from Juergen Gross:
"This contains the following fixes/cleanups:
- the removal of a BUG_ON() which wasn't necessary and which could
trigger now due to a recent change
- a correction of a long standing bug happening very rarely in Xen
dom0 when a hypercall buffer from user land was not accessible by
the hypervisor for very short periods of time due to e.g. page
migration or compaction
- usage of EXPORT_SYMBOL_GPL() instead of EXPORT_SYMBOL() in a
Xen-related driver (no breakage possible as using those symbols
without others already exported via EXPORT-SYMBOL_GPL() wouldn't
make any sense)
- a simplification for Xen PVH or Xen ARM guests
- some additional error handling for callers of xenbus_printf()"
* tag 'for-linus-4.18-rc2-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen: Remove unnecessary BUG_ON from __unbind_from_irq()
xen: add new hypercall buffer mapping device
xen/scsiback: add error handling for xenbus_printf
scsi: xen-scsifront: add error handling for xenbus_printf
xen/grant-table: Export gnttab_{alloc|free}_pages as GPL
xen: add error handling for xenbus_printf
xen: share start flags between PV and PVH
|
|
Required to queue a dependent fix.
|
|
syzbot is reporting NULL pointer dereference at wb_workfn() [1] due to
wb->bdi->dev being NULL. And Dmitry confirmed that wb->state was
WB_shutting_down after wb->bdi->dev became NULL. This indicates that
unregister_bdi() failed to call wb_shutdown() on one of wb objects.
The problem is in cgwb_bdi_unregister() which does cgwb_kill() and thus
drops bdi's reference to wb structures before going through the list of
wbs again and calling wb_shutdown() on each of them. This way the loop
iterating through all wbs can easily miss a wb if that wb has already
passed through cgwb_remove_from_bdi_list() called from wb_shutdown()
from cgwb_release_workfn() and as a result fully shutdown bdi although
wb_workfn() for this wb structure is still running. In fact there are
also other ways cgwb_bdi_unregister() can race with
cgwb_release_workfn() leading e.g. to use-after-free issues:
CPU1 CPU2
cgwb_bdi_unregister()
cgwb_kill(*slot);
cgwb_release()
queue_work(cgwb_release_wq, &wb->release_work);
cgwb_release_workfn()
wb = list_first_entry(&bdi->wb_list, ...)
spin_unlock_irq(&cgwb_lock);
wb_shutdown(wb);
...
kfree_rcu(wb, rcu);
wb_shutdown(wb); -> oops use-after-free
We solve these issues by synchronizing writeback structure shutdown from
cgwb_bdi_unregister() with cgwb_release_workfn() using a new mutex. That
way we also no longer need synchronization using WB_shutting_down as the
mutex provides it for CONFIG_CGROUP_WRITEBACK case and without
CONFIG_CGROUP_WRITEBACK wb_shutdown() can be called only once from
bdi_unregister().
Reported-by: syzbot <syzbot+4a7438e774b21ddd8eca@syzkaller.appspotmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
When delivering a signal to a task that is using rseq, we call into
__rseq_handle_notify_resume() so that the registers pushed in the
sigframe are updated to reflect the state of the restartable sequence
(for example, ensuring that the signal returns to the abort handler if
necessary).
However, if the rseq management fails due to an unrecoverable fault when
accessing userspace or certain combinations of RSEQ_CS_* flags, then we
will attempt to deliver a SIGSEGV. This has the potential for infinite
recursion if the rseq code continuously fails on signal delivery.
Avoid this problem by using force_sigsegv() instead of force_sig(), which
is explicitly designed to reset the SEGV handler to SIG_DFL in the case
of a recursive fault. In doing so, remove rseq_signal_deliver() from the
internal rseq API and have an optional struct ksignal * parameter to
rseq_handle_notify_resume() instead.
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: peterz@infradead.org
Cc: paulmck@linux.vnet.ibm.com
Cc: boqun.feng@gmail.com
Link: https://lkml.kernel.org/r/1529664307-983-1-git-send-email-will.deacon@arm.com
|
|
Function irq_desc_get_msi_desc() is not referenced in the kernel (and does
not seem to have been referenced since e39758e0ea76, 3 years ago), so
delete it.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: <marc.zyngier@arm.com>
Cc: <will.deacon@arm.com>
Cc: <kstewart@linuxfoundation.org>
Cc: <julien.thierry@arm.com>
Cc: <andrew@lunn.ch>
Cc: <trivial@kernel.org>
Link: https://lkml.kernel.org/r/1529667333-92959-1-git-send-email-john.garry@huawei.com
|
|
Debug is missing the IRQCHIP_SUPPORTS_LEVEL_MSI debug entry, making debugfs
slightly less useful.
Take this opportunity to also add a missing comment in the definition of
IRQCHIP_SUPPORTS_LEVEL_MSI.
Fixes: 6988e0e0d283 ("genirq/msi: Limit level-triggered MSI to platform devices")
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Yang Yingliang <yangyingliang@huawei.com>
Cc: Sumit Garg <sumit.garg@linaro.org>
Link: https://lkml.kernel.org/r/20180622095254.5906-2-marc.zyngier@arm.com
|
|
One of my tests compiles the kernel with gcc 4.5.3, and I hit the
following build error:
include/linux/semaphore.h: In function 'sema_init':
include/linux/semaphore.h:35:17: error: unknown field 'val' specified in initializer
include/linux/semaphore.h:35:17: warning: missing braces around initializer
include/linux/semaphore.h:35:17: warning: (near initialization for '(anonymous).raw_lock.<anonymous>.val')
I bisected it down to:
625e88be1f41 ("locking/qspinlock: Merge 'struct __qspinlock' into 'struct qspinlock'")
... which makes qspinlock have an anonymous union, which makes initializing it special
for older compilers. By adding strategic brackets, it makes the build
happy again.
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Acked-by: Waiman Long <longman@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Boqun Feng <boqun.feng@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Fixes: 625e88be1f41 ("locking/qspinlock: Merge 'struct __qspinlock' into 'struct qspinlock'")
Link: http://lkml.kernel.org/r/20180621203526.172ab5c4@vmware.local.home
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Pull NFS client bugfixes from Trond Myklebust:
"Hightlights include:
- fix an rcu deadlock in nfs_delegation_find_inode()
- fix NFSv4 deadlocks due to not freeing the session slot in
layoutget
- don't send layoutreturn if the layout is already invalid
- prevent duplicate XID allocation
- flexfiles: Don't tie up all the rpciod threads in resends"
* tag 'nfs-for-4.18-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
pNFS/flexfiles: Process writeback resends from nfsiod context as well
pNFS/flexfiles: Don't tie up all the rpciod threads in resends
sunrpc: Prevent duplicate XID allocation
pNFS: Don't send layoutreturn if the layout is already invalid
pNFS: Always free the session slot on error in nfs4_layoutget_handle_exception
NFS: Fix an rcu deadlock in nfs_delegation_find_inode()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"These fix a suspend/resume regression in the ACPI driver for Intel
SoCs (LPSS), add a new system wakeup quirk to the ACPI EC driver and
fix an inline stub of a function in the ACPI processor driver that
diverged from the original.
Specifics:
- Fix a suspend/resume regression in the ACPI driver for Intel SoCs
(LPSS) to make it work on systems where some power management
quirks should only be applied for runtime PM and suspend-to-idle
and not for suspend-to-RAM (Rafael Wysocki).
- Add a system wakeup quirk for Thinkpad X1 Carbon 6th to the ACPI EC
driver to avoid drainig battery too fast while suspended to idle on
those systems (Mika Westerberg).
- Fix an inline stub of acpi_processor_ppc_has_changed() to match the
original function definition (Brian Norris)"
* tag 'acpi-4.18-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / processor: Finish making acpi_processor_ppc_has_changed() void
ACPI / EC: Use ec_no_wakeup on Thinkpad X1 Carbon 6th
ACPI / LPSS: Avoid PM quirks on suspend and resume from S3
|
|
Signed-off-by: Wei Wang <wvw@google.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Borislav Petkov <bp@suse.de>
Cc: Crt Mori <cmo@melexis.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: gregkh@linuxfoundation.org
Cc: wei.vince.wang@gmail.com
Link: https://lkml.kernel.org/lkml/20180424212241.16013-1-wvw@google.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Add a new function to "adjust" the current fixed UV memory block size
of 2GB so it can be changed to a different physical boundary. This is
out of necessity so arch dependent code can accommodate specific BIOS
requirements which can align these new PMEM modules at less than the
default boundaries.
A "set order" type of function was used to insure that the memory block
size will be a power of two value without requiring a validity check.
64GB was chosen as the upper limit for memory block size values to
accommodate upcoming 4PB systems which have 6 more bits of physical
address space (46 becoming 52).
Signed-off-by: Mike Travis <mike.travis@hpe.com>
Reviewed-by: Andrew Banman <andrew.banman@hpe.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Dimitri Sivanich <dimitri.sivanich@hpe.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Russ Anderson <russ.anderson@hpe.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: dan.j.williams@intel.com
Cc: jgross@suse.com
Cc: kirill.shutemov@linux.intel.com
Cc: mhocko@suse.com
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/lkml/20180524201711.609546602@stormcage.americas.sgi.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Considering that we explicitly forbid system calls in rseq critical
sections, it is not valid to issue a fork or clone system call within a
rseq critical section, so rseq_fork() is not required to restart an
active rseq c.s. in the child process.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Ben Maurer <bmaurer@fb.com>
Cc: Boqun Feng <boqun.feng@gmail.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Lameter <cl@linux.com>
Cc: Dave Watson <davejwatson@fb.com>
Cc: Joel Fernandes <joelaf@google.com>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: Paul E . McKenney <paulmck@linux.vnet.ibm.com>
Cc: Paul Turner <pjt@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Shuah Khan <shuahkh@osg.samsung.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Cc: linux-api@vger.kernel.org
Cc: linux-kselftest@vger.kernel.org
Link: https://lore.kernel.org/lkml/20180619133230.4087-4-mathieu.desnoyers@efficios.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
After commit 9facc336876f ("bpf: reject any prog that failed read-only lock")
offsetof(struct bpf_binary_header, image) became 3 instead of 4,
breaking powerpc BPF badly, since instructions need to be word aligned.
Fixes: 9facc336876f ("bpf: reject any prog that failed read-only lock")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: Martin KaFai Lau <kafai@fb.com>
Cc: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If NBD_DISCONNECT_ON_CLOSE is set on a device, then the driver will
issue a disconnect from nbd_release if the device has no remaining
bdev->bd_openers.
Fix ret val so reconfigure with only setting the flag succeeds.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Doron Roberts-Kedes <doronrk@fb.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Pull rdma fixes from Jason Gunthorpe:
"Here are eight fairly small fixes collected over the last two weeks.
Regression and crashing bug fixes:
- mlx4/5: Fixes for issues found from various checkers
- A resource tracking and uverbs regression in the core code
- qedr: NULL pointer regression found during testing
- rxe: Various small bugs"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
IB/rxe: Fix missing completion for mem_reg work requests
RDMA/core: Save kernel caller name when creating CQ using ib_create_cq()
IB/uverbs: Fix ordering of ucontext check in ib_uverbs_write
IB/mlx4: Fix an error handling path in 'mlx4_ib_rereg_user_mr()'
RDMA/qedr: Fix NULL pointer dereference when running over iWARP without RDMA-CM
IB/mlx5: Fix return value check in flow_counters_set_data()
IB/mlx5: Fix memory leak in mlx5_ib_create_flow
IB/rxe: avoid double kfree skb
|
|
Pull networking fixes from David Miller:
1) Fix crash on bpf_prog_load() errors, from Daniel Borkmann.
2) Fix ATM VCC memory accounting, from David Woodhouse.
3) fib6_info objects need RCU freeing, from Eric Dumazet.
4) Fix SO_BINDTODEVICE handling for TCP sockets, from David Ahern.
5) Fix clobbered error code in enic_open() failure path, from
Govindarajulu Varadarajan.
6) Propagate dev_get_valid_name() error returns properly, from Li
RongQing.
7) Fix suspend/resume in davinci_emac driver, from Bartosz Golaszewski.
8) Various act_ife fixes (recursive locking, IDR leaks, etc.) from
Davide Caratti.
9) Fix buggy checksum handling in sungem driver, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (40 commits)
ip: limit use of gso_size to udp
stmmac: fix DMA channel hang in half-duplex mode
net: stmmac: socfpga: add additional ocp reset line for Stratix10
net: sungem: fix rx checksum support
bpfilter: ignore binary files
bpfilter: fix build error
net/usb/drivers: Remove useless hrtimer_active check
net/sched: act_ife: preserve the action control in case of error
net/sched: act_ife: fix recursive lock and idr leak
net: ethernet: fix suspend/resume in davinci_emac
net: propagate dev_get_valid_name return code
enic: do not overwrite error code
net/tcp: Fix socket lookups with SO_BINDTODEVICE
ptp: replace getnstimeofday64() with ktime_get_real_ts64()
net/ipv6: respect rcu grace period before freeing fib6_info
net: net_failover: fix typo in net_failover_slave_register()
ipvlan: use ETH_MAX_MTU as max mtu
net: hamradio: use eth_broadcast_addr
enic: initialize enic->rfs_h.lock in enic_probe
MAINTAINERS: Add Sam as the maintainer for NCSI
...
|
|
Commit bca5f557dcea "ACPI / processor: Make acpi_processor_ppc_has_changed()
void" changed one of the declarations of acpi_processor_ppc_has_changed()
to return void, but the !CPU_FREQ version still returns int. Let's return
void to be consistent.
Fixes: bca5f557dcea "ACPI / processor: Make acpi_processor_ppc_has_changed() void"
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|