| Age | Commit message (Collapse) | Author |
|---|
|
Need rc5 for udl fix to add udl cleanups on top.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Recently, for Intel platforms the "ignore_module_refcount" field
was introduced for the component driver. In order to avoid a
deadlock preventing the PCI modules from being removed
even when the card was idle, the refcounts were not incremented
for the device driver module during component probe.
However, this change introduced a nasty side effect:
the device driver module can be unloaded while a pcm stream is open.
This patch proposes to change the field to be renamed as
"module_get_upon_open". When this field is set, the module
refcount should be incremented on pcm open amd decremented
upon pcm close. This will enable modules to be removed
when no PCM playback/capture happens and prevent removal
when the component is actually in use.
Also, align with the skylake component driver with the new name.
Fixes: b450b878('ASoC: core: don't increase component module refcount
unconditionally'
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://anongit.freedesktop.org/drm/drm-intel into drm-next
UAPI Changes:
- Report an error early instead of SIGBUS later when mmap beyond BO size
Core Changes:
- This includes backmerge of drm-next and two merges of Maarten's
topic/hdr-formats
Driver Changes:
- Add Comet Lake (Gen9) PCI IDs to Coffee Lake ID list (Anusha)
- Add missing ICL PCI ID (Jose)
- Fix legacy gamma mode for ICL (Ville)
- Assume eDP is present on port A when there is no VBT (Thomas)
- Corrections to eDP training patterns (Jose)
- Fix PSR2 selective update corruption after PSR1 setup (Jose)
- Fix CRC mismatch error for DP link layer compliance (Aditya)
- Fix CNL DPLL readout and clean up code (Ville)
- Turn off the CUS when turning off a HDR plane (Ville)
- Avoid a race with execlist tasklet during race (Chris)
- Add missing CSC readout and clean up code (Ville)
- Avoid unnecessary wakeref during debugfs/drop_caches/set (Chris, Caz)
- Hold references to ring/HW context/context explicitly when used (Chris)
- Assume next platforms inherit old platform (Rodrigo)
- Use HWS indices rather than addresses for breadcrumbs (Chris)
- Add REG_BIT/REG_GENMASK and REG_FIELD_PREP macros (Jani)
- Convert crept in C99 types to kernel fixed size types (Jani)
- Avoid passing full dev_priv in forcewake functions (Daniele)
- Reset GuC on GPU reset (Sujaritha)
- Rework MG and Combo PLLs to vfuncs (Lucas)
- Explicitly track ppGTT size (Chris, Bob)
- Coding style improvements and code modularization (Ville)
- Selftest and debugging improvements (Chris)
Signed-off-by: Dave Airlie <airlied@redhat.com>
# Conflicts:
# drivers/gpu/drm/i915/intel_hdmi.c
From: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190325124925.GA12726@jlahtine-desk.ger.corp.intel.com
|
|
Linux 5.1-rc1
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Some cleaning after the first batch; mostly about HD-audio quirks but
also some NULL dereference fixes in corner cases and a random build
error fix, too"
* tag 'sound-fix-5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/realtek - Add support headset mode for New DELL WYSE NB
ALSA: hda/realtek - Add support headset mode for DELL WYSE AIO
ALSA: hda/realtek: merge alc_fixup_headset_jack to alc295_fixup_chromebook
ALSA: pcm: Fix function name in kernel-doc comment
ALSA: hda: hdmi - add Icelake support
ALSA: hda - add more quirks for HP Z2 G4 and HP Z240
ALSA: hda/realtek - Fixed Headset Mic JD not stable
ALSA: hda/realtek: Enable headset MIC of Acer TravelMate X514-51T with ALC255
ALSA: hda/tegra: avoid build error without CONFIG_PM
ALSA: usx2y: Fix potential NULL pointer dereference
ALSA: hda: Avoid NULL pointer dereference at snd_hdac_stream_start()
|
|
Signed-off-by: Ricardo Biehl Pasquali <pasqualirb@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The dpcm get from fe_clients/be_clients
may be free before use
Add a spin lock at snd_soc_card level,
to protect the dpcm instance.
The lock may be used in atomic context, so use spin lock.
Use irq spin lock version,
since the lock may be used in interrupts.
possible race condition between
void dpcm_be_disconnect(
...
list_del(&dpcm->list_be);
list_del(&dpcm->list_fe);
kfree(dpcm);
...
and
for_each_dpcm_fe()
for_each_dpcm_be*()
race condition example
Thread 1:
snd_soc_dapm_mixer_update_power()
-> soc_dpcm_runtime_update()
-> dpcm_be_disconnect()
-> kfree(dpcm);
Thread 2:
dpcm_fe_dai_trigger()
-> dpcm_be_dai_trigger()
-> snd_soc_dpcm_can_be_free_stop()
-> if (dpcm->fe == fe)
Excpetion Scenario:
two FE link to same BE
FE1 -> BE
FE2 ->
Thread 1: switch of mixer between FE2 -> BE
Thread 2: pcm_stop FE1
Exception:
Unable to handle kernel paging request at virtual address dead0000000000e0
pc=<> [<ffffff8960e2cd10>] dpcm_be_dai_trigger+0x29c/0x47c
sound/soc/soc-pcm.c:3226
if (dpcm->fe == fe)
lr=<> [<ffffff8960e2f694>] dpcm_fe_dai_do_trigger+0x94/0x26c
Backtrace:
[<ffffff89602dba80>] notify_die+0x68/0xb8
[<ffffff896028c7dc>] die+0x118/0x2a8
[<ffffff89602a2f84>] __do_kernel_fault+0x13c/0x14c
[<ffffff89602a27f4>] do_translation_fault+0x64/0xa0
[<ffffff8960280cf8>] do_mem_abort+0x4c/0xd0
[<ffffff8960282ad0>] el1_da+0x24/0x40
[<ffffff8960e2cd10>] dpcm_be_dai_trigger+0x29c/0x47c
[<ffffff8960e2f694>] dpcm_fe_dai_do_trigger+0x94/0x26c
[<ffffff8960e2edec>] dpcm_fe_dai_trigger+0x3c/0x44
[<ffffff8960de5588>] snd_pcm_do_stop+0x50/0x5c
[<ffffff8960dded24>] snd_pcm_action+0xb4/0x13c
[<ffffff8960ddfdb4>] snd_pcm_drop+0xa0/0x128
[<ffffff8960de69bc>] snd_pcm_common_ioctl+0x9d8/0x30f0
[<ffffff8960de1cac>] snd_pcm_ioctl_compat+0x29c/0x2f14
[<ffffff89604c9d60>] compat_SyS_ioctl+0x128/0x244
[<ffffff8960283740>] el0_svc_naked+0x34/0x38
[<ffffffffffffffff>] 0xffffffffffffffff
Signed-off-by: KaiChieh Chuang <kaichieh.chuang@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big char/misc driver patch pull request for 5.1-rc1.
The largest thing by far is the new habanalabs driver for their AI
accelerator chip. For now it is in the drivers/misc directory but will
probably move to a new directory soon along with other drivers of this
type.
Other than that, just the usual set of individual driver updates and
fixes. There's an "odd" merge in here from the DRM tree that they
asked me to do as the MEI driver is starting to interact with the i915
driver, and it needed some coordination. All of those patches have
been properly acked by the relevant subsystem maintainers.
All of these have been in linux-next with no reported issues, most for
quite some time"
* tag 'char-misc-5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (219 commits)
habanalabs: adjust Kconfig to fix build errors
habanalabs: use %px instead of %p in error print
habanalabs: use do_div for 64-bit divisions
intel_th: gth: Fix an off-by-one in output unassigning
habanalabs: fix little-endian<->cpu conversion warnings
habanalabs: use NULL to initialize array of pointers
habanalabs: fix little-endian<->cpu conversion warnings
habanalabs: soft-reset device if context-switch fails
habanalabs: print pointer using %p
habanalabs: fix memory leak with CBs with unaligned size
habanalabs: return correct error code on MMU mapping failure
habanalabs: add comments in uapi/misc/habanalabs.h
habanalabs: extend QMAN0 job timeout
habanalabs: set DMA0 completion to SOB 1007
habanalabs: fix validation of WREG32 to DMA completion
habanalabs: fix mmu cache registers init
habanalabs: disable CPU access on timeouts
habanalabs: add MMU DRAM default page mapping
habanalabs: Dissociate RAZWI info from event types
misc/habanalabs: adjust Kconfig to fix build errors
...
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: More changes for v5.1
Another batch of changes for ASoC, no big core changes - it's mainly
small fixes and improvements for individual drivers.
- A big refresh and cleanup of the Samsung drivers, fixing a number of
issues which allow the driver to be used with a wider range of
userspaces.
- Fixes for the Intel drivers to make them more standard so less likely
to get bitten by core issues.
- New driver for Cirrus Logic CS35L26.
|
|
|
|
We need 32ea33a04484 ("mei: bus: export to_mei_cl_device for mei
client devices drivers") for the mei-hdcp patches.
References: https://lkml.org/lkml/2019/2/19/356
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
|
|
git://anongit.freedesktop.org/drm/drm-intel into drm-intel-next-queued
Prep patches + headers for the mei-hdcp/i915 component interfaces
Also contains the prep work in the component helpers plus adjustements
for the snd-hda/i915 component interface.
Plus one small static inline in the drm_hdcp.h header that both i915
and mei_hdcp will need.
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
From: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20190219071619.GA11016@phenom.ffwll.local
|
|
Doing a backmerge to be able to merge topic/mei-hdcp-2019-02-19 PR.
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
|
|
drm/i915 is tracking all wakeref owners with a cookie in order to
identify leaks. To that end, each rpm acquisition ops->get_power is
assigned a cookie which should be passed to ops->put_power to signify
its release (and removal from the list of wakeref owners). As snd/hda is
already using a bool to track current status of display_power extending
that to an unsigned long to hold the boolean cookie is a trivial
extension, and will quell all doubt that snd/hda is the cause of the
device runtime pm leaks.
v2: Keep using the power abstraction for local wakeref tracking.
v3: BUILD_BUG_ON impedance mismatch
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Jani Nikula <jani.nikula@intel.com>
Acked-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190213152109.16997-1-chris@chris-wilson.co.uk
|
|
There is now no users of this flag so remove it together with
related code. The chan_name field of snd_dmaengine_dai_dma_data
data structure is not removed as it is still in use by the PXA
platform.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
We never used this field (or in older SOF implementations), let's
remove it
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This field was never used, let's remove it
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The ASoC core has for the longest time increased the module reference
counts, even before the transition to the component model. This is
probably fine on most platforms, but it introduces a deadlock case on
Intel devices with the Skylake and SOF drivers which cannot be removed
due to their reference counts being modified by the core.
In these 2 cases, the PCI or ACPI driver .probe creates a platform
device to let the machine driver .probe register the audio
card. Conversely the PCI or ACPI driver .remove will unregister the
platform device which results in the card being removed by the machine
driver .remove.
With ascii art, this can be represented as
modprobe
snd_soc_skl/
soc-pci-dev/sof-acpci-dev ----------> pci/acpi probe
^ |
| ---------------|
| | |
| V V
increase register register machine
refcount component platform_device
^ |
| |
| V
component <---- register card <---- probe
probe
The issue is that by playing with the component's module reference
counts during the card registration, it's no longer possible to remove
the module which controls the component. This can be shown, e.g. with
the following error:
root@plb-XPS-13-9350:~# lsmod | grep snd_soc_skl
snd_soc_skl 110592 1
root@plb-XPS-13-9350:~# rmmod snd_soc_skl
rmmod: ERROR: Module snd_soc_skl is in use
Increasing the reference count during the component probe is not
useful. If the PCI/ACPI module is removed, the card will be removed
anyway.
To avoid breaking existing platforms and allowing Intel platforms to
safely deal with module load/unload cases, this patch introduces a
flag which needs to be set during the component initialization. This
is a strictly opt-in capability that should only be used when the
handling of the component module does not require a reference count
increase to prevent removal during use.
Note that this solution is not directly applicable to the legacy
Atom/SST driver, which uses a different device hierarchy. There are
however additional refcount issues which prevent the ACPI driver from
being removed. This is a different issue which would need a different
patch.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Since we need multiple components for I915 for different purposes
(Audio & Mei_hdcp), we adopt the subcomponents methodology introduced
by the previous patch (mentioned below).
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Mon Jan 28 17:08:20 2019 +0530
components: multiple components for a device
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by-by: Ramalingam C <ramalinagm.c@intel.com> (commit message)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch> (code)
cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
cc: Russell King <rmk+kernel@arm.linux.org.uk>
cc: Rafael J. Wysocki <rafael@kernel.org>
cc: Jaroslav Kysela <perex@perex.cz>
cc: Takashi Iwai <tiwai@suse.com>
cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
cc: Jani Nikula <jani.nikula@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190207232759.14553-4-daniel.vetter@ffwll.ch
|
|
Now all callers no longer check the return value from
snd_pcm_lib_preallocate_pages() and co, let's make them to return
void, so that any new code won't fall into the same pitfall.
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Updates for v5.1
Lots and lots of new drivers so far, a highlight being the MediaTek
BTCVSD which is a driver for a Bluetooth radio chip - the first such
driver we've had upstream. Hopefully we will soon also see a baseband
with an upstream driver!
- Support for only powering up channels that are actively being used.
- Quite a few improvements to simplify the generic card drivers,
especially the merge of the SCU cards into the main generic drivers.
- Lots of fixes for probing on Intel systems, trying to rationalize
things to look more standard from a framework point of view.
- New drivers for Asahi Kasei Microdevices AK4497, Cirrus Logic CS4341,
Google ChromeOS embedded controllers, Ingenic JZ4725B, MediaTek
BTCVSD, MT8183 and MT6358, NXP MICFIL, Rockchip RK3328, Spreadtrum
DMA controllers, Qualcomm WCD9335, Xilinx S/PDIF and PCM formatters.
|
|
Add driver support for Cirrus Logic CS35L36 boosted
speaker amplifier
Signed-off-by: James Schulman <james.schulman@cirrus.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
To detect potential errors, let's add:
a) build-time warnings when the table size isn't aligned with the enum
list
b) run-time warnings when the values are not initialized. This
requires an increase by one of all values to avoid the default 0.
Suggested-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The creation of card's id proc file can be moved gracefully into
info.c. Also, the assignment of card->proc_id is superfluous and can
be dropped. So let's do it.
Basically this is no functional change but code refactoring, but one
potential behavior change is that now it returns properly the error
code from snd_info_card_register(), which is a good thing (tm).
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
It's referred only in snd_card_id_read() which can receive the card
object via private_data.
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Two new helper functions are added here for cleaning up the existing
lengthy calls.
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
It is normal user behaviour to start, stop, then start a stream
again without closing it. Currently this works for compressed
playback streams but not capture ones.
The states on a compressed capture stream go directly from OPEN to
PREPARED, unlike a playback stream which moves to SETUP and waits
for a write of data before moving to PREPARED. Currently however,
when a stop is sent the state is set to SETUP for both types of
streams. This leaves a capture stream in the situation where a new
start can't be sent as that requires the state to be PREPARED and
a new set_params can't be sent as that requires the state to be
OPEN. The only option being to close the stream, and then reopen.
Correct this issues by allowing snd_compr_drain_notify to set the
state depending on the stream direction, as we already do in
set_params.
Fixes: 49bb6402f1aa ("ALSA: compress_core: Add support for capture streams")
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
soc_tplg_link_config() will find the physical dai link and call
soc_tplg_dai_link_load() to load the BE dai link. Currently remove_link()
is only used to remove the FE dai link which is created by the topology.
The BE dai link cannot however be unloaded in snd_soc_tplg_component
_remove(), which is problematic if anything needs to be released or
reinitialized.
This patch aligns the definitions of dynamic types with the existing
UAPI and adds a new remove_backend_link() routine to unload the the BE
dai link when snd_soc_tplg_component_remove() is invoked.
Signed-off-by: Bard liao <yung-chuan.liao@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Currently all widgets attached to a DAI link will be powered
up when the DAI is active, however this may include routes
that are not actually in use if there are unused channels
available on the DAI.
The macros for creating AIF widgets already include an entry for
slot, it is proposed to change that to channel. The effective
difference here being respresenting the logical channel index
rather than the physical slot index. The CODECs currently
using the slot entry on the DAPM_AIF macros are using it in
a manner consistent with this, the CODECs not using it just
have the field set to zero.
A variable is added to snd_soc_dapm_widget to represent
this channel index and then for each AIF widget attached to
a DAI this is compared against the number of channels on
the stream. Enabling the links for those which will be in
use. This has the nice property that the CODECs which haven't
used the slot/channel entry in the macro will function exactly
as before due to all the AIF widgets having a channel of zero
and a stream by definition having at least one channel.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
We used to pass NULL to memory allocators for ISA devices due to
historical reasons. But we prefer rather a proper device object to be
assigned, so let's fix it by replacing snd_dma_isa_data() call with
card->dev reference, and kill snd_dma_isa_data() definition.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
In the current code, the codec registration may happen both at the
codec bind time and the end of the controller probe time. In a rare
occasion, they race with each other, leading to Oops due to the still
uninitialized card device.
This patch introduces a simple flag to prevent the codec registration
at the codec bind time as long as the controller probe is going on.
The controller probe invokes snd_card_register() that does the whole
registration task, and we don't need to register each piece
beforehand.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Add a new dobj type SND_SOC_DOBJ_GRAPH for dapm routes
and add snd_soc_dobj member to struct snd_soc_dapm_route.
This enables device drivers to save driver specific
data pertaining to dapm routes and also be able
to clean up the data when the driver module is unloaded.
Also, reorder the snd_soc_dobj_type types to align with
matching topology header types.
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Pull 5.0 branch for further development of USB-audio quirks
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
To reuse the same machine drivers with Atom/SST, Skylake and SOF, we
need to change the default platform_name (or platforms->name in the
"modern" representation).
So far, this override was done with an automatic override, which was
broken by a set of changes for DT platforms related to deferred probe
handling.
This automatic override is actually not really needed, the machine
driver can already receive the platform name as a platform_data
parameter. This is used e.g. for HDaudio support where we have
different PCI aliases used for different platforms. We can reuse the
same mechanism and modify the machine drivers to override the dailinks
prior to registrating the card.
This will require additional work for SOF, but with this helper it'll
be just two lines of additional code per machine driver which is
reused, not the end of the world.
This helper can be simplified when all drivers have transitioned to
the "modern" representation of dailinks.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Fix compilation issues reported by 0day-Kbuild with sparc64 w/ SOF.
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Pull PCM lock refactoring.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The proc files are recursively freed by calling with the root
snd_info_entry object, so we don't have to keep each object for
releasing one by one. Move the release of the PCM stream proc root at
the beginning, so that we can remove the redundant code and resource.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
It's assigned but nowhere used. Let's remove it.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
We have currently two global locks, a rwlock and a rwsem, that are
used for managing linking the PCM streams. Due to these global locks,
once when a linked stream is used, the lock granularity suffers a
lot.
This patch attempts to eliminate the former global lock for atomic
ops. The latter rwsem needs remaining because of the loosy way of the
loop calls in snd_pcm_action_nonatomic(), as well as for avoiding the
deadlock at linking. However, these are used far rarely, actually
only by two actions (prepare and reset), where both are no timing
critical ones. So this can be still seen as a good improvement.
The basic strategy to eliminate the rwlock is to assure group->lock at
adding or removing a stream to / from the group. Since we already
takes the group lock whenever taking the all substream locks under the
group, this shouldn't be a big problem. The reference to group
pointer in snd_pcm_substream object is protected by the stream lock
itself.
However, there are still pitfalls: a race window at re-locking and the
lifecycle of group object. The former is a small race window for
dereferencing the substream group object opened while snd_pcm_action()
performs re-locking to avoid ABBA deadlocks. This includes the unlink
of group during that window, too. And the latter is the kfree
performed after all streams are removed from the group while it's
still dereferenced.
For addressing these corner cases, two new tricks are introduced:
- After re-locking, the group assigned to the stream is checked again;
if the group is changed, we retry the whole procedure.
- Introduce a refcount to snd_pcm_group object, so that it's freed
only when it's empty and really no one refers to it.
(Some readers might wonder why not RCU for the latter. RCU in this
case would cost more than refcounting, unfortunately. We take the
group lock sooner or later, hence the performance improvement by RCU
would be negligible. Meanwhile, because we need to deal with
schedulable context depending on the pcm->nonatomic flag, it'll become
dynamic RCU/SRCU switch, and the grace period may become too long.)
Along with these changes, there are a significant amount of code
refactoring. The complex group re-lock & ref code is factored out to
snd_pcm_stream_group_ref() function, for example.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Current simple-card is using asoc_simple_card_canonicalize_dailink().
Its naming is "dailink", but is for "platform".
We already have asoc_simple_card_canonicalize_cpu() for "cpu",
let's follow same naming rule.
It never return error, so, void function is better idea.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Current snd_soc_dai_link is starting to use snd_soc_dai_link_component
(= modern) style for Platform, but it is still assuming single Platform
so far. We will need to have multi Platform support in the not far
future.
Currently only simple card is using it as sound card driver,
and other drivers are converted to it from legacy style by
snd_soc_init_platform().
To avoid future problem of multi Platform support, let's add
num_platforms before it is too late.
In the same time, to make it same naming mothed, "platform" should
be "platforms". This patch fixup it too.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Make a common helper to re-assign the PCM link using list_move() instead
of open code with manual list_del() and list_add_tail(). This assures
the consistency and we can get rid of snd_pcm_group.count field -- its
purpose is only to check whether the list is singular, and we can know
it by list_is_singular() call now.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Current ALSA SoC is assuming 1 CPU 1 Platform (= DMA) style system.
Because of this background, it is directly using
xxx_name / xxx_of_node / xxx_dai_name on dai_link.
Let's call it as legacy style here.
More complex style system like multi CPU multi Platform (= DMA) will
coming. To supporting it, we can use snd_soc_dai_link_component on
dai_link. Let's call it as modern style here.
But current ALSA SoC can't support it so far. Thus, we need to have
multi CPU / multi Codec / multi Platform style in the future on ALSA SoC.
Currently we already have multi Codec support. Platform is starting to
use modern style on dai_link, but still style only. Multi Platform is
not yet implemented. And we still don't have multi CPU support on ALSA
SoC, and not have modern style either.
Currently, if driver is using legacy style Codec/Platform, it will be
converted to modern style on soc-core. This means, we are using glue code
for legacy vs modern style so far on ALSA SoC.
We can fully switch to modern style on all drivers if ALSA SoC supported
modern style for CPU, and then, legacy style code will be removed from
ALSA SoC.
Untile then, we need to keep both legacy/modern style and its glue code.
This patch adds such future plan and background on soc.h
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
ASoC: Fixes for v5.0
Quite a big batch of fixes here. There's a couple of things going on,
the main one is that we found some issues with not deferring probe when
we should, causing us to skip some driver initialization. The fixes for
this then in turn exposed some issues with how we were searching for
components which had previously gone unnoticed due to the original
issue.
There's also been the normal driver specific stuff and there's been what
looks like several batches of automated scanning for issues which have
generated quite a large set of smaller fixes for potential crashes and
missed error handling.
|
|
Pull the PCM suspend improvement / cleanup.
This moves the most of snd_pcm_suspend*() calls into PCM's own device
PM ops. There should be no change from the functionality POV.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v5.0
Quite a big batch of fixes here. There's a couple of things going on,
the main one is that we found some issues with not deferring probe when
we should, causing us to skip some driver initialization. The fixes for
this then in turn exposed some issues with how we were searching for
components which had previously gone unnoticed due to the original
issue.
There's also been the normal driver specific stuff and there's been what
looks like several batches of automated scanning for issues which have
generated quite a large set of smaller fixes for potential crashes and
missed error handling.
|
|
snd_pcm_suspend() is no longer called from outside, so let's make it
local static. Also drop a superfluous NULL check there.
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Until now we rely on each driver calling snd_pcm_suspend*() explicitly
at its own PM handling. However, this can be done far more easily by
setting the PM ops to each actual snd_pcm device object.
This patch adds the device_type object for PCM stream and assigns to
each PCM stream object. The type contains only the PM ops for system
suspend; we don't need to deal with the resume in general.
The suspend hook simply calls snd_pcm_suspend_all() for the given PCM
streams. This implies that the PM order is correctly put, i.e. PCM is
suspended before the main (or codec) driver, which should be true in
general. If a special ordering is needed, you'd need to adjust the
device PM order manually later.
This patch introduces a new flag, snd_pcm.no_device_suspend, too.
With this flag set, the PCM device object won't invoke
snd_pcm_suspend_all() by itself. This is needed for ASoC who wants to
manage the PM call orders in its serialized way, and the flag is set
in soc_new_pcm() as default.
For the non-ASoC world, we can get rid of the manual snd_pcm_suspend
calls. This will be done in the later patches.
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
snd_soc_init_platform initializes pointers to snd_soc_dai_link which is
statically allocated and it does this by devm_kzalloc. In the event of
an EPROBE_DEFER the memory will be freed and the pointers are left
dangling. snd_soc_init_platform sees the dangling pointers and assumes
they are pointing to initialized memory and does not reallocate them on
the second probe attempt which results in a use after free bug since
devm has freed the memory from the first probe attempt.
Since the intention for snd_soc_dai_link->platform is that it can be set
statically by the machine driver we need to respect the pointer in the
event we did not set it but still catch dangling pointers. The solution
is to add a flag to track whether the pointer was dynamically allocated
or not.
Signed-off-by: Curtis Malainey <cujomalainey@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
