| Age | Commit message (Collapse) | Author |
|---|
|
Adding delays to TCP flows is crucial for studying behavior
of TCP stacks, including congestion control modules.
Linux offers netem module, but it has unpractical constraints :
- Need root access to change qdisc
- Hard to setup on egress if combined with non trivial qdisc like FQ
- Single delay for all flows.
EDT (Earliest Departure Time) adoption in TCP stack allows us
to enable a per socket delay at a very small cost.
Networking tools can now establish thousands of flows, each of them
with a different delay, simulating real world conditions.
This requires FQ packet scheduler or a EDT-enabled NIC.
This patchs adds TCP_TX_DELAY socket option, to set a delay in
usec units.
unsigned int tx_delay = 10000; /* 10 msec */
setsockopt(fd, SOL_TCP, TCP_TX_DELAY, &tx_delay, sizeof(tx_delay));
Note that FQ packet scheduler limits might need some tweaking :
man tc-fq
PARAMETERS
limit
Hard limit on the real queue size. When this limit is
reached, new packets are dropped. If the value is lowered,
packets are dropped so that the new limit is met. Default
is 10000 packets.
flow_limit
Hard limit on the maximum number of packets queued per
flow. Default value is 100.
Use of TCP_TX_DELAY option will increase number of skbs in FQ qdisc,
so packets would be dropped if any of the previous limit is hit.
Use of a jump label makes this support runtime-free, for hosts
never using the option.
Also note that TSQ (TCP Small Queues) limits are slightly changed
with this patch : we need to account that skbs artificially delayed
wont stop us providind more skbs to feed the pipe (netem uses
skb_orphan_partial() for this purpose, but FQ can not use this trick)
Because of that, using big delays might very well trigger
old bugs in TSO auto defer logic and/or sndbuf limited detection.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
TLS offload drivers keep track of TCP seq numbers to make sure
the packets are fed into the HW in order.
When packets get dropped on the way through the stack, the driver
will get out of sync and have to use fallback encryption, but unless
TCP seq number is resynced it will never match the packets correctly
(or even worse - use incorrect record sequence number after TCP seq
wraps).
Existing drivers (mlx5) feed the entire record on every out-of-order
event, allowing FW/HW to always be in sync.
This patch adds an alternative, more akin to the RX resync. When
driver sees a frame which is past its expected sequence number the
stream must have gotten out of order (if the sequence number is
smaller than expected its likely a retransmission which doesn't
require resync). Driver will ask the stack to perform TX sync
before it submits the next full record, and fall back to software
crypto until stack has performed the sync.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently only RX direction is ever resynced, however, TX may
also get out of sequence if packets get dropped on the way to
the driver. Rename the resync callback and add a direction
parameter.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
TLS offload device may lose sync with the TCP stream if packets
arrive out of order. Drivers can currently request a resync at
a specific TCP sequence number. When a record is found starting
at that sequence number kernel will inform the device of the
corresponding record number.
This requires the device to constantly scan the stream for a
known pattern (constant bytes of the header) after sync is lost.
This patch adds an alternative approach which is entirely under
the control of the kernel. Kernel tracks records it had to fully
decrypt, even though TLS socket is in TLS_HW mode. If multiple
records did not have any decrypted parts - it's a pretty strong
indication that the device is out of sync.
We choose the min number of fully encrypted records to be 2,
which should hopefully be more than will get retransmitted at
a time.
After kernel decides the device is out of sync it schedules a
resync request. If the TCP socket is empty the resync gets
performed immediately. If socket is not empty we leave the
record parser to resync when next record comes.
Before resync in message parser we peek at the TCP socket and
don't attempt the sync if the socket already has some of the
next record queued.
On resync failure (encrypted data continues to flow in) we
retry with exponential backoff, up to once every 128 records
(with a 16k record thats at most once every 2M of data).
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
handle_device_resync() doesn't describe the function very well.
The function checks if resync should be issued upon parsing of
a new record.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
TLS offload code casts record number to a u64. The buffer
should be aligned to 8 bytes, but its actually a __be64, and
the rest of the TLS code treats it as big int. Make the
offload callbacks take a byte array, drivers can make the
choice to do the ugly cast if they want to.
Prepare for copying the record number onto the stack by
defining a constant for max size of the byte array.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for RTA_NH_ID attribute to allow a user to specify a
nexthop id to use with a route. fc_nh_id is added to fib6_config to
hold the value passed in the RTA_NH_ID attribute. If a nexthop id
is given, the gateway, device, encap and multipath attributes can
not be set.
Update ip6_route_del to check metric and protocol before nexthop
specs. If fc_nh_id is set, then it must match the id in the route
entry. Since IPv6 allows delete of a cached entry (an exception),
add ip6_del_cached_rt_nh to cycle through all of the fib6_nh in
a fib entry if it is using a nexthop.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for RTA_NH_ID attribute to allow a user to specify a
nexthop id to use with a route. fc_nh_id is added to fib_config to
hold the value passed in the RTA_NH_ID attribute. If a nexthop id
is given, the gateway, device, encap and multipath attributes can
not be set.
Update fib_nh_match to check ids on a route delete.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IPv6 has traditionally had a single fib6_nh per fib6_info. With
nexthops we can have multiple fib6_nh associated with a fib6_info.
Add a nexthop helper to invoke a callback for each fib6_nh in a
'struct nexthop'. If the callback returns non-0, the loop is
stopped and the return value passed to the caller.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case autoflowlabel is in action, skb_get_hash_flowi6()
derives a non zero skb->hash to the flowlabel.
If skb->hash is zero, a flow dissection is performed.
Since all TCP skbs sent from ESTABLISH state inherit their
skb->hash from sk->sk_txhash, we better keep a copy
of sk->sk_txhash into the TIME_WAIT socket.
After this patch, ACK or RST packets sent on behalf of
a TIME_WAIT socket have the flowlabel that was previously
used by the flow.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Based on review, `lock' is only acquired in hwbm_pool_add() which is
invoked via ->probe(), ->resume() and ->ndo_change_mtu(). Based on this
the lock can become a mutex and there is no need to disable interrupts
during the procedure.
Now that the lock is a mutex, hwbm_pool_add() no longer invokes
hwbm_pool_refill() in an atomic context so we can pass GFP_KERNEL to
hwbm_pool_refill() and remove the `gfp' argument from hwbm_pool_add().
Cc: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The nhg->nh_entries[] array is allocated in nexthop_grp_alloc() and it
has nhg->num_nh elements so this check should be >= instead of >.
Fixes: 430a049190de ("nexthop: Add support for nexthop groups")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Where possible, we generally want both the bond master and the relevant slave
information in message output. Standardize the format using new slave_*
printk macros.
Suggested-by: Joe Perches <joe@perches.com>
CC: Jay Vosburgh <j.vosburgh@gmail.com>
CC: Veaceslav Falico <vfalico@gmail.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: netdev@vger.kernel.org
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is helpful for e.g. draining per-driver (not per-port) tagger
queues.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some ISDN files that got removed in net-next had some changes
done in mainline, take the removals.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes from David Miller:
1) Free AF_PACKET po->rollover properly, from Willem de Bruijn.
2) Read SFP eeprom in max 16 byte increments to avoid problems with
some SFP modules, from Russell King.
3) Fix UDP socket lookup wrt. VRF, from Tim Beale.
4) Handle route invalidation properly in s390 qeth driver, from Julian
Wiedmann.
5) Memory leak on unload in RDS, from Zhu Yanjun.
6) sctp_process_init leak, from Neil HOrman.
7) Fix fib_rules rule insertion semantic change that broke Android,
from Hangbin Liu.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (33 commits)
pktgen: do not sleep with the thread lock held.
net: mvpp2: Use strscpy to handle stat strings
net: rds: fix memory leak in rds_ib_flush_mr_pool
ipv6: fix EFAULT on sendto with icmpv6 and hdrincl
ipv6: use READ_ONCE() for inet->hdrincl as in ipv4
Revert "fib_rules: return 0 directly if an exactly same rule exists when NLM_F_EXCL not supplied"
net: aquantia: fix wol configuration not applied sometimes
ethtool: fix potential userspace buffer overflow
Fix memory leak in sctp_process_init
net: rds: fix memory leak when unload rds_rdma
ipv6: fix the check before getting the cookie in rt6_get_cookie
ipv4: not do cache for local delivery if bc_forwarding is enabled
s390/qeth: handle error when updating TX queue count
s390/qeth: fix VLAN attribute in bridge_hostnotify udev event
s390/qeth: check dst entry before use
s390/qeth: handle limited IPv4 broadcast in L3 TX path
net: fix indirect calls helpers for ptype list hooks.
net: ipvlan: Fix ipvlan device tso disabled while NETIF_F_IP_CSUM is set
udp: only choose unbound UDP socket for multicast when not in a VRF
net/tls: replace the sleeping lock around RX resync with a bit lock
...
|
|
While offloading TLS connections, drivers need to handle the case where
out of order packets need to be transmitted.
Other drivers obtain the entire TLS record for the specific skb to
provide as context to hardware for encryption. However, other designs
may also want to keep the hardware state intact and perform the
out of order encryption entirely on the host.
To achieve this, export the already existing software encryption
fallback path so drivers could access this.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently drivers have to ensure the alignment of their tls state
structure, which leads to unnecessary layers of getters and
encapsulated structures in each driver.
Simplify all this by marking the driver state as aligned (driver_state
members are currently aligned, so no hole is added, besides ALIGN in
TLS_OFFLOAD_CONTEXT_SIZE_RX/TX would reserve this extra space, anyway.)
With that we can add a common accessor to the core.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
8 bytes of driver state has been enough so far, but for drivers
which have to store 8 byte handle it's no longer practical to
store the state directly in the context.
Drivers generally don't need much extra state on RX side, while
TX side has to be tracking TCP sequence numbers. Split the
lengths of max driver state size on RX and TX.
The struct tls_offload_context_tx currently stands at 616 bytes and
struct tls_offload_context_rx stands at 368 bytes. Upcoming work
will consume extra 8 bytes in both for kernel-driven resync.
This means that we can bump TX side to 16 bytes and still fit
into the same number of cache lines but on RX side we would be 8
bytes over.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The monolithic hash_lock could cause huge contention when
inserting/deletiing vxlan_fdbs into the fdb_head.
Use FDB_HASH_SIZE hash_locks to protect insertions/deletions
of vxlan_fdbs into the fdb_head hash table.
Suggested-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Litao jiao <jiaolitao@raisecom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In Jianlin's testing, netperf was broken with 'Connection reset by peer',
as the cookie check failed in rt6_check() and ip6_dst_check() always
returned NULL.
It's caused by Commit 93531c674315 ("net/ipv6: separate handling of FIB
entries from dst based routes"), where the cookie can be got only when
'c1'(see below) for setting dst_cookie whereas rt6_check() is called
when !'c1' for checking dst_cookie, as we can see in ip6_dst_check().
Since in ip6_dst_check() both rt6_dst_from_check() (c1) and rt6_check()
(!c1) will check the 'from' cookie, this patch is to remove the c1 check
in rt6_get_cookie(), so that the dst_cookie can always be set properly.
c1:
(rt->rt6i_flags & RTF_PCPU || unlikely(!list_empty(&rt->rt6i_uncached)))
Fixes: 93531c674315 ("net/ipv6: separate handling of FIB entries from dst based routes")
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add struct nexthop and nh_list list_head to fib6_info. nh_list is the
fib6_info side of the nexthop <-> fib_info relationship. Since a fib6_info
referencing a nexthop object can not have 'sibling' entries (the old way
of doing multipath routes), the nh_list is a union with fib6_siblings.
Add f6i_list list_head to 'struct nexthop' to track fib6_info entries
using a nexthop instance. Update __remove_nexthop_fib to walk f6_list
and delete fib entries using the nexthop.
Add a few nexthop helpers for use when a nexthop is added to fib6_info:
- nexthop_fib6_nh - return first fib6_nh in a nexthop object
- fib6_info_nh_dev moved to nexthop.h and updated to use nexthop_fib6_nh
if the fib6_info references a nexthop object
- nexthop_path_fib6_result - similar to ipv4, select a path within a
multipath nexthop object. If the nexthop is a blackhole, set
fib6_result type to RTN_BLACKHOLE, and set the REJECT flag
Update the fib6_info references to check for nh and take a different path
as needed:
- rt6_qualify_for_ecmp - if a fib entry uses a nexthop object it can NOT
be coalesced with other fib entries into a multipath route
- rt6_duplicate_nexthop - use nexthop_cmp if either fib6_info references
a nexthop
- addrconf (host routes), RA's and info entries (anything configured via
ndisc) does not use nexthop objects
- fib6_info_destroy_rcu - put reference to nexthop object
- fib6_purge_rt - drop fib6_info from f6i_list
- fib6_select_path - update to use the new nexthop_path_fib6_result when
fib entry uses a nexthop object
- rt6_device_match - update to catch use of nexthop object as a blackhole
and set fib6_type and flags.
- ip6_route_info_create - don't add space for fib6_nh if fib entry is
going to reference a nexthop object, take a reference to nexthop object,
disallow use of source routing
- rt6_nlmsg_size - add space for RTA_NH_ID
- add rt6_fill_node_nexthop to add nexthop data on a dump
As with ipv4, most of the changes push existing code into the else branch
of whether the fib entry uses a nexthop object.
Update the nexthop code to walk f6i_list on a nexthop deleted to remove
fib entries referencing it.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add 'struct nexthop' and nh_list list_head to fib_info. nh_list is the
fib_info side of the nexthop <-> fib_info relationship.
Add fi_list list_head to 'struct nexthop' to track fib_info entries
using a nexthop instance. Add __remove_nexthop_fib and add it to
__remove_nexthop to walk the new list_head and mark those fib entries
as dead when the nexthop is deleted.
Add a few nexthop helpers for use when a nexthop is added to fib_info:
- nexthop_cmp to determine if 2 nexthops are the same
- nexthop_path_fib_result to select a path for a multipath
'struct nexthop'
- nexthop_fib_nhc to select a specific fib_nh_common within a
multipath 'struct nexthop'
Update existing fib_info_nhc to use nexthop_fib_nhc if a fib_info uses
a 'struct nexthop', and mark fib_info_nh as only used for the non-nexthop
case.
Update the fib_info functions to check for fi->nh and take a different
path as needed:
- free_fib_info_rcu - put the nexthop object reference
- fib_release_info - remove the fib_info from the nexthop's fi_list
- nh_comp - use nexthop_cmp when either fib_info references a nexthop
object
- fib_info_hashfn - use the nexthop id for the hashing vs the oif of
each fib_nh in a fib_info
- fib_nlmsg_size - add space for the RTA_NH_ID attribute
- fib_create_info - verify nexthop reference can be taken, verify
nexthop spec is valid for fib entry, and add fib_info to fi_list for
a nexthop
- fib_select_multipath - use the new nexthop_path_fib_result to select a
path when nexthop objects are used
- fib_table_lookup - if the 'struct nexthop' is a blackhole nexthop, treat
it the same as a fib entry using 'blackhole'
The bulk of the changes are in fib_semantics.c and most of that is
moving the existing change_nexthops into an else branch.
Update the nexthop code to walk fi_list on a nexthop deleted to remove
fib entries referencing it.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Convert more IPv4 code to use fib_nh_common over fib_nh to enable routes
to use a fib6_nh based nexthop. In the end, only code not using a
nexthop object in a fib_info should directly access fib_nh in a fib_info
without checking the famiy and going through fib_nh_common. Those
functions will be marked when it is not directly evident.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use helpers to access fib_nh and fib_nhs fields of a fib_info. Drop the
fib_dev macro which is an alias for the first nexthop. Replacements:
fi->fib_dev --> fib_info_nh(fi, 0)->fib_nh_dev
fi->fib_nh --> fib_info_nh(fi, 0)
fi->fib_nh[i] --> fib_info_nh(fi, i)
fi->fib_nhs --> fib_info_num_path(fi)
where fib_info_nh(fi, i) returns fi->fib_nh[nhsel] and fib_info_num_path
returns fi->fib_nhs.
Move the existing fib_info_nhc to nexthop.h and define the new ones
there. A later patch adds a check if a fib_info uses a nexthop object,
and defining the helpers in nexthop.h avoid circular header
dependencies.
After this all remaining open coded references to fi->fib_nhs and
fi->fib_nh are in:
- fib_create_info and helpers used to lookup an existing fib_info
entry, and
- the netdev event functions fib_sync_down_dev and fib_sync_up.
The latter two will not be reused for nexthops, and the fib_create_info
will be updated to handle a nexthop in a fib_info.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All callers pass prot->version as the last parameter
of tls_advance_record_sn(), yet tls_advance_record_sn()
itself needs a pointer to prot. Pass prot from callers.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
struct tls_context is slightly badly laid out. If we reorder things
right we can save 16 bytes (320 -> 304) but also make all fast path
data fit into two cache lines (one read only and one read/write,
down from four cache lines).
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce a function to be called from drivers during flash. It sends
notification to userspace about flash update progress.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 38030d7cb779 ("net/tls: avoid NULL-deref on resync during device removal")
tried to fix a potential NULL-dereference by taking the
context rwsem. Unfortunately the RX resync may get called
from soft IRQ, so we can't use the rwsem to protect from
the device disappearing. Because we are guaranteed there
can be only one resync at a time (it's called from strparser)
use a bit to indicate resync is busy and make device
removal wait for the bit to get cleared.
Note that there is a leftover "flags" field in struct
tls_context already.
Fixes: 4799ac81e52a ("tls: Add rx inline crypto offload")
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
syzbot reported nasty use-after-free [1]
Lets remove frag_list field from structs ip_fraglist_iter
and ip6_fraglist_iter. This seens not needed anyway.
[1] :
BUG: KASAN: use-after-free in kfree_skb_list+0x5d/0x60 net/core/skbuff.c:706
Read of size 8 at addr ffff888085a3cbc0 by task syz-executor303/8947
CPU: 0 PID: 8947 Comm: syz-executor303 Not tainted 5.2.0-rc2+ #12
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x172/0x1f0 lib/dump_stack.c:113
print_address_description.cold+0x7c/0x20d mm/kasan/report.c:188
__kasan_report.cold+0x1b/0x40 mm/kasan/report.c:317
kasan_report+0x12/0x20 mm/kasan/common.c:614
__asan_report_load8_noabort+0x14/0x20 mm/kasan/generic_report.c:132
kfree_skb_list+0x5d/0x60 net/core/skbuff.c:706
ip6_fragment+0x1ef4/0x2680 net/ipv6/ip6_output.c:882
__ip6_finish_output+0x577/0xaa0 net/ipv6/ip6_output.c:144
ip6_finish_output+0x38/0x1f0 net/ipv6/ip6_output.c:156
NF_HOOK_COND include/linux/netfilter.h:294 [inline]
ip6_output+0x235/0x7f0 net/ipv6/ip6_output.c:179
dst_output include/net/dst.h:433 [inline]
ip6_local_out+0xbb/0x1b0 net/ipv6/output_core.c:179
ip6_send_skb+0xbb/0x350 net/ipv6/ip6_output.c:1796
ip6_push_pending_frames+0xc8/0xf0 net/ipv6/ip6_output.c:1816
rawv6_push_pending_frames net/ipv6/raw.c:617 [inline]
rawv6_sendmsg+0x2993/0x35e0 net/ipv6/raw.c:947
inet_sendmsg+0x141/0x5d0 net/ipv4/af_inet.c:802
sock_sendmsg_nosec net/socket.c:652 [inline]
sock_sendmsg+0xd7/0x130 net/socket.c:671
___sys_sendmsg+0x803/0x920 net/socket.c:2292
__sys_sendmsg+0x105/0x1d0 net/socket.c:2330
__do_sys_sendmsg net/socket.c:2339 [inline]
__se_sys_sendmsg net/socket.c:2337 [inline]
__x64_sys_sendmsg+0x78/0xb0 net/socket.c:2337
do_syscall_64+0xfd/0x680 arch/x86/entry/common.c:301
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x44add9
Code: e8 7c e6 ff ff 48 83 c4 18 c3 0f 1f 80 00 00 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 1b 05 fc ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:00007f826f33bce8 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 00000000006e7a18 RCX: 000000000044add9
RDX: 0000000000000000 RSI: 0000000020000240 RDI: 0000000000000005
RBP: 00000000006e7a10 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00000000006e7a1c
R13: 00007ffcec4f7ebf R14: 00007f826f33c9c0 R15: 20c49ba5e353f7cf
Allocated by task 8947:
save_stack+0x23/0x90 mm/kasan/common.c:71
set_track mm/kasan/common.c:79 [inline]
__kasan_kmalloc mm/kasan/common.c:489 [inline]
__kasan_kmalloc.constprop.0+0xcf/0xe0 mm/kasan/common.c:462
kasan_slab_alloc+0xf/0x20 mm/kasan/common.c:497
slab_post_alloc_hook mm/slab.h:437 [inline]
slab_alloc_node mm/slab.c:3269 [inline]
kmem_cache_alloc_node+0x131/0x710 mm/slab.c:3579
__alloc_skb+0xd5/0x5e0 net/core/skbuff.c:199
alloc_skb include/linux/skbuff.h:1058 [inline]
__ip6_append_data.isra.0+0x2a24/0x3640 net/ipv6/ip6_output.c:1519
ip6_append_data+0x1e5/0x320 net/ipv6/ip6_output.c:1688
rawv6_sendmsg+0x1467/0x35e0 net/ipv6/raw.c:940
inet_sendmsg+0x141/0x5d0 net/ipv4/af_inet.c:802
sock_sendmsg_nosec net/socket.c:652 [inline]
sock_sendmsg+0xd7/0x130 net/socket.c:671
___sys_sendmsg+0x803/0x920 net/socket.c:2292
__sys_sendmsg+0x105/0x1d0 net/socket.c:2330
__do_sys_sendmsg net/socket.c:2339 [inline]
__se_sys_sendmsg net/socket.c:2337 [inline]
__x64_sys_sendmsg+0x78/0xb0 net/socket.c:2337
do_syscall_64+0xfd/0x680 arch/x86/entry/common.c:301
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Freed by task 8947:
save_stack+0x23/0x90 mm/kasan/common.c:71
set_track mm/kasan/common.c:79 [inline]
__kasan_slab_free+0x102/0x150 mm/kasan/common.c:451
kasan_slab_free+0xe/0x10 mm/kasan/common.c:459
__cache_free mm/slab.c:3432 [inline]
kmem_cache_free+0x86/0x260 mm/slab.c:3698
kfree_skbmem net/core/skbuff.c:625 [inline]
kfree_skbmem+0xc5/0x150 net/core/skbuff.c:619
__kfree_skb net/core/skbuff.c:682 [inline]
kfree_skb net/core/skbuff.c:699 [inline]
kfree_skb+0xf0/0x390 net/core/skbuff.c:693
kfree_skb_list+0x44/0x60 net/core/skbuff.c:708
__dev_xmit_skb net/core/dev.c:3551 [inline]
__dev_queue_xmit+0x3034/0x36b0 net/core/dev.c:3850
dev_queue_xmit+0x18/0x20 net/core/dev.c:3914
neigh_direct_output+0x16/0x20 net/core/neighbour.c:1532
neigh_output include/net/neighbour.h:511 [inline]
ip6_finish_output2+0x1034/0x2550 net/ipv6/ip6_output.c:120
ip6_fragment+0x1ebb/0x2680 net/ipv6/ip6_output.c:863
__ip6_finish_output+0x577/0xaa0 net/ipv6/ip6_output.c:144
ip6_finish_output+0x38/0x1f0 net/ipv6/ip6_output.c:156
NF_HOOK_COND include/linux/netfilter.h:294 [inline]
ip6_output+0x235/0x7f0 net/ipv6/ip6_output.c:179
dst_output include/net/dst.h:433 [inline]
ip6_local_out+0xbb/0x1b0 net/ipv6/output_core.c:179
ip6_send_skb+0xbb/0x350 net/ipv6/ip6_output.c:1796
ip6_push_pending_frames+0xc8/0xf0 net/ipv6/ip6_output.c:1816
rawv6_push_pending_frames net/ipv6/raw.c:617 [inline]
rawv6_sendmsg+0x2993/0x35e0 net/ipv6/raw.c:947
inet_sendmsg+0x141/0x5d0 net/ipv4/af_inet.c:802
sock_sendmsg_nosec net/socket.c:652 [inline]
sock_sendmsg+0xd7/0x130 net/socket.c:671
___sys_sendmsg+0x803/0x920 net/socket.c:2292
__sys_sendmsg+0x105/0x1d0 net/socket.c:2330
__do_sys_sendmsg net/socket.c:2339 [inline]
__se_sys_sendmsg net/socket.c:2337 [inline]
__x64_sys_sendmsg+0x78/0xb0 net/socket.c:2337
do_syscall_64+0xfd/0x680 arch/x86/entry/common.c:301
entry_SYSCALL_64_after_hwframe+0x49/0xbe
The buggy address belongs to the object at ffff888085a3cbc0
which belongs to the cache skbuff_head_cache of size 224
The buggy address is located 0 bytes inside of
224-byte region [ffff888085a3cbc0, ffff888085a3cca0)
The buggy address belongs to the page:
page:ffffea0002168f00 refcount:1 mapcount:0 mapping:ffff88821b6f63c0 index:0x0
flags: 0x1fffc0000000200(slab)
raw: 01fffc0000000200 ffffea00027bbf88 ffffea0002105b88 ffff88821b6f63c0
raw: 0000000000000000 ffff888085a3c080 000000010000000c 0000000000000000
page dumped because: kasan: bad access detected
Memory state around the buggy address:
ffff888085a3ca80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
ffff888085a3cb00: 00 00 00 00 00 00 00 00 00 00 00 00 fc fc fc fc
>ffff888085a3cb80: fc fc fc fc fc fc fc fc fb fb fb fb fb fb fb fb
^
ffff888085a3cc00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
ffff888085a3cc80: fb fb fb fb fc fc fc fc fc fc fc fc fc fc fc fc
Fixes: 0feca6190f88 ("net: ipv6: add skbuff fraglist splitter")
Fixes: c8b17be0b7a4 ("net: ipv4: add skbuff fraglist splitter")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
flow_stats_update() uses max_t, so ensure we have that defined.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This flag is not used by any caller, remove it.
Signed-off-by: Stanislav Fomichev <sdf@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset container Netfilter/IPVS update for net-next:
1) Add UDP tunnel support for ICMP errors in IPVS.
Julian Anastasov says:
This patchset is a followup to the commit that adds UDP/GUE tunnel:
"ipvs: allow tunneling with gue encapsulation".
What we do is to put tunnel real servers in hash table (patch 1),
add function to lookup tunnels (patch 2) and use it to strip the
embedded tunnel headers from ICMP errors (patch 3).
2) Extend xt_owner to match for supplementary groups, from
Lukasz Pawelczyk.
3) Remove unused oif field in flow_offload_tuple object, from
Taehee Yoo.
4) Release basechain counters from workqueue to skip synchronize_rcu()
call. From Florian Westphal.
5) Replace skb_make_writable() by skb_ensure_writable(). Patchset
from Florian Westphal.
6) Checksum support for gue encapsulation in IPVS, from Jacky Hu.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The phylink conflict was between a bug fix by Russell King
to make sure we have a consistent PHY interface mode, and
a change in net-next to pull some code in phylink_resolve()
into the helper functions phylink_mac_link_{up,down}()
On the dp83867 side it's mostly overlapping changes, with
the 'net' side removing a condition that was supposed to
trigger for RGMII but because of how it was coded never
actually could trigger.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add checksum support for gue encapsulation with the tun_flags parameter,
which could be one of the values below:
IP_VS_TUNNEL_ENCAP_FLAG_NOCSUM
IP_VS_TUNNEL_ENCAP_FLAG_CSUM
IP_VS_TUNNEL_ENCAP_FLAG_REMCSUM
Signed-off-by: Jacky Hu <hengqing.hu@gmail.com>
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
The oifidx in the struct flow_offload_tuple is not used anymore.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Add ip_vs_find_tunnel() to match tunnel headers
by family, address and optional port. Use it to
properly find the tunnel real server used in
received ICMP errors.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Before now rs_table was used only for NAT real servers.
Change it to allow TUN real severs from different types,
possibly hashed with different port key.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull yet more SPDX updates from Greg KH:
"Here is another set of reviewed patches that adds SPDX tags to
different kernel files, based on a set of rules that are being used to
parse the comments to try to determine that the license of the file is
"GPL-2.0-or-later" or "GPL-2.0-only". Only the "obvious" versions of
these matches are included here, a number of "non-obvious" variants of
text have been found but those have been postponed for later review
and analysis.
There is also a patch in here to add the proper SPDX header to a bunch
of Kbuild files that we have missed in the past due to new files being
added and forgetting that Kbuild uses two different file names for
Makefiles. This issue was reported by the Kbuild maintainer.
These patches have been out for review on the linux-spdx@vger mailing
list, and while they were created by automatic tools, they were
hand-verified by a bunch of different people, all whom names are on
the patches are reviewers"
* tag 'spdx-5.2-rc3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (82 commits)
treewide: Add SPDX license identifier - Kbuild
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 225
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 224
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 223
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 222
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 221
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 220
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 218
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 217
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 216
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 215
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 214
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 213
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 211
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 210
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 209
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 207
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 206
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 203
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 201
...
|
|
Pull networking fixes from David Miller:
1) Fix OOPS during nf_tables rule dump, from Florian Westphal.
2) Use after free in ip_vs_in, from Yue Haibing.
3) Fix various kTLS bugs (NULL deref during device removal resync,
netdev notification ignoring, etc.) From Jakub Kicinski.
4) Fix ipv6 redirects with VRF, from David Ahern.
5) Memory leak fix in igmpv3_del_delrec(), from Eric Dumazet.
6) Missing memory allocation failure check in ip6_ra_control(), from
Gen Zhang. And likewise fix ip_ra_control().
7) TX clean budget logic error in aquantia, from Igor Russkikh.
8) SKB leak in llc_build_and_send_ui_pkt(), from Eric Dumazet.
9) Double frees in mlx5, from Parav Pandit.
10) Fix lost MAC address in r8169 during PCI D3, from Heiner Kallweit.
11) Fix botched register access in mvpp2, from Antoine Tenart.
12) Use after free in napi_gro_frags(), from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (89 commits)
net: correct zerocopy refcnt with udp MSG_MORE
ethtool: Check for vlan etype or vlan tci when parsing flow_rule
net: don't clear sock->sk early to avoid trouble in strparser
net-gro: fix use-after-free read in napi_gro_frags()
net: dsa: tag_8021q: Create a stable binary format
net: dsa: tag_8021q: Change order of rx_vid setup
net: mvpp2: fix bad MVPP2_TXQ_SCHED_TOKEN_CNTR_REG queue value
ipv4: tcp_input: fix stack out of bounds when parsing TCP options.
mlxsw: spectrum: Prevent force of 56G
mlxsw: spectrum_acl: Avoid warning after identical rules insertion
net: dsa: mv88e6xxx: fix handling of upper half of STATS_TYPE_PORT
r8169: fix MAC address being lost in PCI D3
net: core: support XDP generic on stacked devices.
netvsc: unshare skb in VF rx handler
udp: Avoid post-GRO UDP checksum recalculation
net: phy: dp83867: Set up RGMII TX delay
net: phy: dp83867: do not call config_init twice
net: phy: dp83867: increase SGMII autoneg timer duration
net: phy: dp83867: fix speed 10 in sgmii mode
net: phy: marvell10g: report if the PHY fails to boot firmware
...
|
|
The same skb_checksum_ops struct is defined twice in two different places,
leading to code duplication. Declare it as a global variable into a common
header instead of allocating it on the stack on each function call.
bloat-o-meter reports a slight code shrink.
add/remove: 1/1 grow/shrink: 0/10 up/down: 128/-1282 (-1154)
Function old new delta
sctp_csum_ops - 128 +128
crc32c_csum_ops 16 - -16
sctp_rcv 6616 6583 -33
sctp_packet_pack 4542 4504 -38
nf_conntrack_sctp_packet 4980 4926 -54
execute_masked_set_action 6453 6389 -64
tcf_csum_sctp 575 428 -147
sctp_gso_segment 1292 1126 -166
sctp_csum_check 579 412 -167
sctp_snat_handler 957 772 -185
sctp_dnat_handler 1321 1132 -189
l4proto_manip_pkt 2536 2313 -223
Total: Before=359297613, After=359296459, chg -0.00%
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds basic connection tracking support for the bridge,
including initial IPv4 support.
This patch register two hooks to deal with the bridge forwarding path,
one from the bridge prerouting hook to call nf_conntrack_in(); and
another from the bridge postrouting hook to confirm the entry.
The conntrack bridge prerouting hook defragments packets before passing
them to nf_conntrack_in() to look up for an existing entry, otherwise a
new entry is allocated and it is attached to the skbuff. The conntrack
bridge postrouting hook confirms new conntrack entries, ie. if this is
the first packet seen, then it adds the entry to the hashtable and (if
needed) it refragments the skbuff into the original fragments, leaving
the geometry as is if possible. Exceptions are linearized skbuffs, eg.
skbuffs that are passed up to nfqueue and conntrack helpers, as well as
cloned skbuff for the local delivery (eg. tcpdump), also in case of
bridge port flooding (cloned skbuff too).
The packet defragmentation is done through the ip_defrag() call. This
forces us to save the bridge control buffer, reset the IP control buffer
area and then restore it after call. This function also bumps the IP
fragmentation statistics, it would be probably desiderable to have
independent statistics for the bridge defragmentation/refragmentation.
The maximum fragment length is stored in the control buffer and it is
used to refragment the skbuff from the postrouting path.
The new fraglist splitter and fragment transformer APIs are used to
implement the bridge refragmentation code. The br_ip_fragment() function
drops the packet in case the maximum fragment size seen is larger than
the output port MTU.
This patchset follows the principle that conntrack should not drop
packets, so users can do it through policy via invalid state matching.
Like br_netfilter, there is no refragmentation for packets that are
passed up for local delivery, ie. prerouting -> input path. There are
calls to nf_reset() already in several spots in the stack since time ago
already, eg. af_packet, that show that skbuff fraglist handling from the
netif_rx path is supported already.
The helpers are called from the postrouting hook, before confirmation,
from there we may see packet floods to bridge ports. Then, although
unlikely, this may result in exercising the helpers many times for each
clone. It would be good to explore how to pass all the packets in a list
to the conntrack hook to do this handle only once for this case.
Thanks to Florian Westphal for handing me over an initial patchset
version to add support for conntrack bridge.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds infrastructure to register and to unregister bridge
support for the conntrack module via nf_ct_bridge_register() and
nf_ct_bridge_unregister().
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch exposes a new API to refragment a skbuff. This allows you to
split either a linear skbuff or to force the refragmentation of an
existing fraglist using a different mtu. The API consists of:
* ip6_frag_init(), that initializes the internal state of the transformer.
* ip6_frag_next(), that allows you to fetch the next fragment. This function
internally allocates the skbuff that represents the fragment, it pushes
the IPv6 header, and it also copies the payload for each fragment.
The ip6_frag_state object stores the internal state of the splitter.
This code has been extracted from ip6_fragment(). Symbols are also
exported to allow to reuse this iterator from the bridge codepath to
build its own refragmentation routine by reusing the existing codebase.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch exposes a new API to refragment a skbuff. This allows you to
split either a linear skbuff or to force the refragmentation of an
existing fraglist using a different mtu. The API consists of:
* ip_frag_init(), that initializes the internal state of the transformer.
* ip_frag_next(), that allows you to fetch the next fragment. This function
internally allocates the skbuff that represents the fragment, it pushes
the IPv4 header, and it also copies the payload for each fragment.
The ip_frag_state object stores the internal state of the splitter.
This code has been extracted from ip_do_fragment(). Symbols are also
exported to allow to reuse this iterator from the bridge codepath to
build its own refragmentation routine by reusing the existing codebase.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the skbuff fraglist split iterator. This API provides an
iterator to transform the fraglist into single skbuff objects, it
consists of:
* ip6_fraglist_init(), that initializes the internal state of the
fraglist iterator.
* ip6_fraglist_prepare(), that restores the IPv6 header on the fragment.
* ip6_fraglist_next(), that retrieves the fragment from the fraglist and
updates the internal state of the iterator to point to the next
fragment in the fraglist.
The ip6_fraglist_iter object stores the internal state of the iterator.
This code has been extracted from ip6_fragment(). Symbols are also
exported to allow to reuse this iterator from the bridge codepath to
build its own refragmentation routine by reusing the existing codebase.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the skbuff fraglist splitter. This API provides an
iterator to transform the fraglist into single skbuff objects, it
consists of:
* ip_fraglist_init(), that initializes the internal state of the
fraglist splitter.
* ip_fraglist_prepare(), that restores the IPv4 header on the
fragments.
* ip_fraglist_next(), that retrieves the fragment from the fraglist and
it updates the internal state of the splitter to point to the next
fragment skbuff in the fraglist.
The ip_fraglist_iter object stores the internal state of the iterator.
This code has been extracted from ip_do_fragment(). Symbols are also
exported to allow to reuse this iterator from the bridge codepath to
build its own refragmentation routine by reusing the existing codebase.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We would like to be able to rotate TFO keys while minimizing the number of
client cookies that are rejected. Currently, we have only one key which can
be used to generate and validate cookies, thus if we simply replace this
key clients can easily have cookies rejected upon rotation.
We propose having the ability to have both a primary key and a backup key.
The primary key is used to generate as well as to validate cookies.
The backup is only used to validate cookies. Thus, keys can be rotated as:
1) generate new key
2) add new key as the backup key
3) swap the primary and backup key, thus setting the new key as the primary
We don't simply set the new key as the primary key and move the old key to
the backup slot because the ip may be behind a load balancer and we further
allow for the fact that all machines behind the load balancer will not be
updated simultaneously.
We make use of this infrastructure in subsequent patches.
Suggested-by: Igor Lubashev <ilubashe@akamai.com>
Signed-off-by: Jason Baron <jbaron@akamai.com>
Signed-off-by: Christoph Paasch <cpaasch@apple.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not see http www gnu org
licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 228 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528171438.107155473@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Based on 1 normalized pattern(s):
license terms gnu general public license gpl version 2
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 161 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528170027.447718015@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
