| Age | Commit message (Collapse) | Author |
|---|
|
Separate the code that counts the interface types and channels from
the code that check the interface combinations. The new function that
checks for combinations is exported so it can be called by the
drivers.
This is done in preparation for moving the interface combinations
checks out of cfg80211.
Signed-off-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Allow GO operation on a channel marked with IEEE80211_CHAN_GO_CONCURRENT
iff there is an active station interface that is associated to
an AP operating on the same channel in the 2 GHz band or the same UNII band
(in the 5 GHz band). This relaxation is not allowed if the channel is
marked with IEEE80211_CHAN_RADAR.
Note that this is a permissive approach to the FCC definitions,
that require a clear assessment that the device operating the AP is
an authorized master, i.e., with radar detection and DFS capabilities.
It is assumed that such restrictions are enforced by user space.
Furthermore, it is assumed, that if the conditions that allowed for
the operation of the GO on such a channel change, i.e., the station
interface disconnected from the AP, it is the responsibility of user
space to evacuate the GO from the channel.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The FCC are clarifying some soft configuration requirements,
which among other include the following:
1. Indoor operation, where a device can use channels requiring indoor
operation, subject to that it can guarantee indoor operation,
i.e., the device is connected to AC Power or the device is under
the control of a local master that is acting as an AP and is
connected to AC Power.
2. Concurrent GO operation, where devices may instantiate a P2P GO
while they are under the guidance of an authorized master. For example,
on a channel on which a BSS is connected to an authorized master, i.e.,
with DFS and radar detection capability in the UNII band.
See https://apps.fcc.gov/eas/comments/GetPublishedDocument.html?id=327&tn=528122
Add support for advertising Indoor-only and GO-Concurrent channel
properties.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This will allow the low level driver to make decision based
on the vif such as queues etc...
Since the vif might be NULL, we can't add it to the tracing
functions.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
[fix staging rtl8821ae driver]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When dynamically creating interfaces from userspace, e.g. for P2P usage,
such interfaces are usually owned by the process that created them, i.e.
wpa_supplicant. Should wpa_supplicant crash, such interfaces will often
cease operating properly and cause problems on restarting the process.
To avoid this problem, introduce an ownership concept for interfaces. If
an interface is owned by a netlink socket, then it will be destroyed if
the netlink socket is closed for any reason, including if the process it
belongs to crashed. This gives us a race-free way to get rid of any such
interfaces.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Pull more networking updates from David Miller:
1) If a VXLAN interface is created with no groups, we can crash on
reception of packets. Fix from Mike Rapoport.
2) Missing includes in CPTS driver, from Alexei Starovoitov.
3) Fix string validations in isdnloop driver, from YOSHIFUJI Hideaki
and Dan Carpenter.
4) Missing irq.h include in bnxw2x, enic, and qlcnic drivers. From
Josh Boyer.
5) AF_PACKET transmit doesn't statistically count TX drops, from Daniel
Borkmann.
6) Byte-Queue-Limit enabled drivers aren't handled properly in
AF_PACKET transmit path, also from Daniel Borkmann.
Same problem exists in pktgen, and Daniel fixed it there too.
7) Fix resource leaks in driver probe error paths of new sxgbe driver,
from Francois Romieu.
8) Truesize of SKBs can gradually get more and more corrupted in NAPI
packet recycling path, fix from Eric Dumazet.
9) Fix uniprocessor netfilter build, from Florian Westphal. In the
longer term we should perhaps try to find a way for ARRAY_SIZE() to
work even with zero sized array elements.
10) Fix crash in netfilter conntrack extensions due to mis-estimation of
required extension space. From Andrey Vagin.
11) Since we commit table rule updates before trying to copy the
counters back to userspace (it's the last action we perform), we
really can't signal the user copy with an error as we are beyond the
point from which we can unwind everything. This causes all kinds of
use after free crashes and other mysterious behavior.
From Thomas Graf.
12) Restore previous behvaior of div/mod by zero in BPF filter
processing. From Daniel Borkmann.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (38 commits)
net: sctp: wake up all assocs if sndbuf policy is per socket
isdnloop: several buffer overflows
netdev: remove potentially harmful checks
pktgen: fix xmit test for BQL enabled devices
net/at91_ether: avoid NULL pointer dereference
tipc: Let tipc_release() return 0
at86rf230: fix MAX_CSMA_RETRIES parameter
mac802154: fix duplicate #include headers
sxgbe: fix duplicate #include headers
net: filter: be more defensive on div/mod by X==0
netfilter: Can't fail and free after table replacement
xen-netback: Trivial format string fix
net: bcmgenet: Remove unnecessary version.h inclusion
net: smc911x: Remove unused local variable
bonding: Inactive slaves should keep inactive flag's value
netfilter: nf_tables: fix wrong format in request_module()
netfilter: nf_tables: set names cannot be larger than 15 bytes
netfilter: nf_conntrack: reserve two bytes for nf_ct_ext->len
netfilter: Add {ipt,ip6t}_osf aliases for xt_osf
netfilter: x_tables: allow to use cgroup match for LOCAL_IN nf hooks
...
|
|
"len" contains sizeof(nf_ct_ext) and size of extensions. In a worst
case it can contain all extensions. Bellow you can find sizes for all
types of extensions. Their sum is definitely bigger than 256.
nf_ct_ext_types[0]->len = 24
nf_ct_ext_types[1]->len = 32
nf_ct_ext_types[2]->len = 24
nf_ct_ext_types[3]->len = 32
nf_ct_ext_types[4]->len = 152
nf_ct_ext_types[5]->len = 2
nf_ct_ext_types[6]->len = 16
nf_ct_ext_types[7]->len = 8
I have seen "len" up to 280 and my host has crashes w/o this patch.
The right way to fix this problem is reducing the size of the ecache
extension (4) and Florian is going to do this, but these changes will
be quite large to be appropriate for a stable tree.
Fixes: 5b423f6a40a0 (netfilter: nf_conntrack: fix racy timer handling with reliable)
Cc: Pablo Neira Ayuso <pablo@netfilter.org>
Cc: Patrick McHardy <kaber@trash.net>
Cc: Jozsef Kadlecsik <kadlec@blackhole.kfki.hu>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrey Vagin <avagin@openvz.org>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup
Pull cgroup updates from Tejun Heo:
"A lot updates for cgroup:
- The biggest one is cgroup's conversion to kernfs. cgroup took
after the long abandoned vfs-entangled sysfs implementation and
made it even more convoluted over time. cgroup's internal objects
were fused with vfs objects which also brought in vfs locking and
object lifetime rules. Naturally, there are places where vfs rules
don't fit and nasty hacks, such as credential switching or lock
dance interleaving inode mutex and cgroup_mutex with object serial
number comparison thrown in to decide whether the operation is
actually necessary, needed to be employed.
After conversion to kernfs, internal object lifetime and locking
rules are mostly isolated from vfs interactions allowing shedding
of several nasty hacks and overall simplification. This will also
allow implmentation of operations which may affect multiple cgroups
which weren't possible before as it would have required nesting
i_mutexes.
- Various simplifications including dropping of module support,
easier cgroup name/path handling, simplified cgroup file type
handling and task_cg_lists optimization.
- Prepatory changes for the planned unified hierarchy, which is still
a patchset away from being actually operational. The dummy
hierarchy is updated to serve as the default unified hierarchy.
Controllers which aren't claimed by other hierarchies are
associated with it, which BTW was what the dummy hierarchy was for
anyway.
- Various fixes from Li and others. This pull request includes some
patches to add missing slab.h to various subsystems. This was
triggered xattr.h include removal from cgroup.h. cgroup.h
indirectly got included a lot of files which brought in xattr.h
which brought in slab.h.
There are several merge commits - one to pull in kernfs updates
necessary for converting cgroup (already in upstream through
driver-core), others for interfering changes in the fixes branch"
* 'for-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup: (74 commits)
cgroup: remove useless argument from cgroup_exit()
cgroup: fix spurious lockdep warning in cgroup_exit()
cgroup: Use RCU_INIT_POINTER(x, NULL) in cgroup.c
cgroup: break kernfs active_ref protection in cgroup directory operations
cgroup: fix cgroup_taskset walking order
cgroup: implement CFTYPE_ONLY_ON_DFL
cgroup: make cgrp_dfl_root mountable
cgroup: drop const from @buffer of cftype->write_string()
cgroup: rename cgroup_dummy_root and related names
cgroup: move ->subsys_mask from cgroupfs_root to cgroup
cgroup: treat cgroup_dummy_root as an equivalent hierarchy during rebinding
cgroup: remove NULL checks from [pr_cont_]cgroup_{name|path}()
cgroup: use cgroup_setup_root() to initialize cgroup_dummy_root
cgroup: reorganize cgroup bootstrapping
cgroup: relocate setting of CGRP_DEAD
cpuset: use rcu_read_lock() to protect task_cs()
cgroup_freezer: document freezer_fork() subtleties
cgroup: update cgroup_transfer_tasks() to either succeed or fail
cgroup: drop task_lock() protection around task->cgroups
cgroup: update how a newly forked task gets associated with css_set
...
|
|
Pull networking updates from David Miller:
"Here is my initial pull request for the networking subsystem during
this merge window:
1) Support for ESN in AH (RFC 4302) from Fan Du.
2) Add full kernel doc for ethtool command structures, from Ben
Hutchings.
3) Add BCM7xxx PHY driver, from Florian Fainelli.
4) Export computed TCP rate information in netlink socket dumps, from
Eric Dumazet.
5) Allow IPSEC SA to be dumped partially using a filter, from Nicolas
Dichtel.
6) Convert many drivers to pci_enable_msix_range(), from Alexander
Gordeev.
7) Record SKB timestamps more efficiently, from Eric Dumazet.
8) Switch to microsecond resolution for TCP round trip times, also
from Eric Dumazet.
9) Clean up and fix 6lowpan fragmentation handling by making use of
the existing inet_frag api for it's implementation.
10) Add TX grant mapping to xen-netback driver, from Zoltan Kiss.
11) Auto size SKB lengths when composing netlink messages based upon
past message sizes used, from Eric Dumazet.
12) qdisc dumps can take a long time, add a cond_resched(), From Eric
Dumazet.
13) Sanitize netpoll core and drivers wrt. SKB handling semantics.
Get rid of never-used-in-tree netpoll RX handling. From Eric W
Biederman.
14) Support inter-address-family and namespace changing in VTI tunnel
driver(s). From Steffen Klassert.
15) Add Altera TSE driver, from Vince Bridgers.
16) Optimizing csum_replace2() so that it doesn't adjust the checksum
by checksumming the entire header, from Eric Dumazet.
17) Expand BPF internal implementation for faster interpreting, more
direct translations into JIT'd code, and much cleaner uses of BPF
filtering in non-socket ocntexts. From Daniel Borkmann and Alexei
Starovoitov"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1976 commits)
netpoll: Use skb_irq_freeable to make zap_completion_queue safe.
net: Add a test to see if a skb is freeable in irq context
qlcnic: Fix build failure due to undefined reference to `vxlan_get_rx_port'
net: ptp: move PTP classifier in its own file
net: sxgbe: make "core_ops" static
net: sxgbe: fix logical vs bitwise operation
net: sxgbe: sxgbe_mdio_register() frees the bus
Call efx_set_channels() before efx->type->dimension_resources()
xen-netback: disable rogue vif in kthread context
net/mlx4: Set proper build dependancy with vxlan
be2net: fix build dependency on VxLAN
mac802154: make csma/cca parameters per-wpan
mac802154: allow only one WPAN to be up at any given time
net: filter: minor: fix kdoc in __sk_run_filter
netlink: don't compare the nul-termination in nla_strcmp
can: c_can: Avoid led toggling for every packet.
can: c_can: Simplify TX interrupt cleanup
can: c_can: Store dlc private
can: c_can: Reduce register access
can: c_can: Make the code readable
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
Pull trivial tree updates from Jiri Kosina:
"Usual rocket science -- mostly documentation and comment updates"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
sparse: fix comment
doc: fix double words
isdn: capi: fix "CAPI_VERSION" comment
doc: DocBook: Fix typos in xml and template file
Bluetooth: add module name for btwilink
driver core: unexport static function create_syslog_header
mmc: core: typo fix in printk specifier
ARM: spear: clean up editing mistake
net-sysfs: fix comment typo 'CONFIG_SYFS'
doc: Insert MODULE_ in module-signing macros
Documentation: update URL to hfsplus Technote 1150
gpio: update path to documentation
ixgbe: Fix format string in ixgbe_fcoe.
Kconfig: Remove useless "default N" lines
user_namespace.c: Remove duplicated word in comment
CREDITS: fix formatting
treewide: Fix typo in Documentation/DocBook
mm: Fix warning on make htmldocs caused by slab.c
ata: ata-samsung_cf: cleanup in header file
idr: remove unused prototype of idr_free()
|
|
Commit 9b2777d6089bcd (ieee802154: add TX power control to wpan_phy)
and following erroneously added CSMA and CCA parameters for 802.15.4
devices as PHY parameters, while they are actually MAC parameters and
can differ for any two WPAN instances. Since it is now sensible to have
multiple WPAN devices with differing CSMA/CCA parameters, make these
parameters MAC parameters instead.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next
John W. Linville says:
====================
pull request: wireless-next 2014-03-31
Please accept this one last round of general wireless updates for
the 3.15 merge window!
For the Bluetooth bits, Gustavo says:
"Here follow another set of patches to 3.15. This is mostly a bug fix
pull request with the exception of one commit from Marcel which adds
tracking to the current configured LE scan type parameter."
Beyond that, notable bits include some final refactoring of rtl8180
and the addition of the rtl8187se driver, fixes for a number of
problems identified by Dan Carpenter and his static analysis tools,
and a handful of other bits here and there.
Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move the whole rt6_need_strict as static inline into ip6_route.h,
so that it can be reused
Signed-off-by: Wang Yufen <wangyufen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem
|
|
This patch basically does two things, i) removes the extern keyword
from the include/linux/filter.h file to be more consistent with the
rest of Joe's changes, and ii) moves filter accounting into the filter
core framework.
Filter accounting mainly done through sk_filter_{un,}charge() take
care of the case when sockets are being cloned through sk_clone_lock()
so that removal of the filter on one socket won't result in eviction
as it's still referenced by the other.
These functions actually belong to net/core/filter.c and not
include/net/sock.h as we want to keep all that in a central place.
It's also not in fast-path so uninlining them is fine and even allows
us to get rd of sk_filter_release_rcu()'s EXPORT_SYMBOL and a forward
declaration.
Joint work with Alexei Starovoitov.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Cc: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/ethernet/marvell/mvneta.c
The mvneta.c conflict is a case of overlapping changes,
a conversion to devm_ioremap_resource() vs. a conversion
to netdev_alloc_pcpu_stats.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
addrconf_join_solict and addrconf_join_anycast may cause actions which
need rtnl locked, especially on first address creation.
A new DAD state is introduced which defers processing of the initial
DAD processing into a workqueue.
To get rtnl lock we need to push the code paths which depend on those
calls up to workqueues, specifically addrconf_verify and the DAD
processing.
(v2)
addrconf_dad_failure needs to be queued up to the workqueue, too. This
patch introduces a new DAD state and stop the DAD processing in the
workqueue (this is because of the possible ipv6_del_addr processing
which removes the solicited multicast address from the device).
addrconf_verify_lock is removed, too. After the transition it is not
needed any more.
As we are not processing in bottom half anymore we need to be a bit more
careful about disabling bottom half out when we lock spin_locks which are also
used in bh.
Relevant backtrace:
[ 541.030090] RTNL: assertion failed at net/core/dev.c (4496)
[ 541.031143] CPU: 0 PID: 0 Comm: swapper/0 Tainted: G O 3.10.33-1-amd64-vyatta #1
[ 541.031145] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2007
[ 541.031146] ffffffff8148a9f0 000000000000002f ffffffff813c98c1 ffff88007c4451f8
[ 541.031148] 0000000000000000 0000000000000000 ffffffff813d3540 ffff88007fc03d18
[ 541.031150] 0000880000000006 ffff88007c445000 ffffffffa0194160 0000000000000000
[ 541.031152] Call Trace:
[ 541.031153] <IRQ> [<ffffffff8148a9f0>] ? dump_stack+0xd/0x17
[ 541.031180] [<ffffffff813c98c1>] ? __dev_set_promiscuity+0x101/0x180
[ 541.031183] [<ffffffff813d3540>] ? __hw_addr_create_ex+0x60/0xc0
[ 541.031185] [<ffffffff813cfe1a>] ? __dev_set_rx_mode+0xaa/0xc0
[ 541.031189] [<ffffffff813d3a81>] ? __dev_mc_add+0x61/0x90
[ 541.031198] [<ffffffffa01dcf9c>] ? igmp6_group_added+0xfc/0x1a0 [ipv6]
[ 541.031208] [<ffffffff8111237b>] ? kmem_cache_alloc+0xcb/0xd0
[ 541.031212] [<ffffffffa01ddcd7>] ? ipv6_dev_mc_inc+0x267/0x300 [ipv6]
[ 541.031216] [<ffffffffa01c2fae>] ? addrconf_join_solict+0x2e/0x40 [ipv6]
[ 541.031219] [<ffffffffa01ba2e9>] ? ipv6_dev_ac_inc+0x159/0x1f0 [ipv6]
[ 541.031223] [<ffffffffa01c0772>] ? addrconf_join_anycast+0x92/0xa0 [ipv6]
[ 541.031226] [<ffffffffa01c311e>] ? __ipv6_ifa_notify+0x11e/0x1e0 [ipv6]
[ 541.031229] [<ffffffffa01c3213>] ? ipv6_ifa_notify+0x33/0x50 [ipv6]
[ 541.031233] [<ffffffffa01c36c8>] ? addrconf_dad_completed+0x28/0x100 [ipv6]
[ 541.031241] [<ffffffff81075c1d>] ? task_cputime+0x2d/0x50
[ 541.031244] [<ffffffffa01c38d6>] ? addrconf_dad_timer+0x136/0x150 [ipv6]
[ 541.031247] [<ffffffffa01c37a0>] ? addrconf_dad_completed+0x100/0x100 [ipv6]
[ 541.031255] [<ffffffff8105313a>] ? call_timer_fn.isra.22+0x2a/0x90
[ 541.031258] [<ffffffffa01c37a0>] ? addrconf_dad_completed+0x100/0x100 [ipv6]
Hunks and backtrace stolen from a patch by Stephen Hemminger.
Reported-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To be consistent, lets use msec for this timeout as well.
Note: This define value is a minimum scan time taken from BT Core spec 4.0,
Vol 3, Part C, chapter 9.2.6
Signed-off-by: Lukasz Rymanowski <lukasz.rymanowski@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
With this patch it is possible to control discovery interleaved
timeout value from debugfs.
It is for fine tuning of this timeout.
Signed-off-by: Lukasz Rymanowski <lukasz.rymanowski@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Keep msec instead of jiffies in this define. This is needed by following
patch where we want this timeout to be exposed in debugfs.
Note: Value of this timeout comes from recommendation in BT Core Spec.4.0,
Vol 3, Part C, chapter 13.2.1.
Signed-off-by: Lukasz Rymanowski <lukasz.rymanowski@tieto.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
If an IPv6 host route with metrics exists, an attempt to add a
new route for the same target with different metrics fails but
rewrites the metrics anyway:
12sp0:~ # ip route add fec0::1 dev eth0 rto_min 1000
12sp0:~ # ip -6 route show
fe80::/64 dev eth0 proto kernel metric 256
fec0::1 dev eth0 metric 1024 rto_min lock 1s
12sp0:~ # ip route add fec0::1 dev eth0 rto_min 1500
RTNETLINK answers: File exists
12sp0:~ # ip -6 route show
fe80::/64 dev eth0 proto kernel metric 256
fec0::1 dev eth0 metric 1024 rto_min lock 1.5s
This is caused by all IPv6 host routes using the metrics in
their inetpeer (or the shared default). This also holds for the
new route created in ip6_route_add() which shares the metrics
with the already existing route and thus ip6_route_add()
rewrites the metrics even if the new route ends up not being
used at all.
Another problem is that old metrics in inetpeer can reappear
unexpectedly for a new route, e.g.
12sp0:~ # ip route add fec0::1 dev eth0 rto_min 1000
12sp0:~ # ip route del fec0::1
12sp0:~ # ip route add fec0::1 dev eth0
12sp0:~ # ip route change fec0::1 dev eth0 hoplimit 10
12sp0:~ # ip -6 route show
fe80::/64 dev eth0 proto kernel metric 256
fec0::1 dev eth0 metric 1024 hoplimit 10 rto_min lock 1s
Resolve the first problem by moving the setting of metrics down
into fib6_add_rt2node() to the point we are sure we are
inserting the new route into the tree. Second problem is
addressed by introducing new flag DST_METRICS_FORCE_OVERWRITE
which is set for a new host route in ip6_route_add() and makes
ipv6_cow_metrics() always overwrite the metrics in inetpeer
(even if they are not "new"); it is reset after that.
v5: use a flag in _metrics member rather than one in flags
v4: fix a typo making a condition always true (thanks to Hannes
Frederic Sowa)
v3: rewritten based on David Miller's idea to move setting the
metrics (and allocation in non-host case) down to the point we
already know the route is to be inserted. Also rebased to
net-next as it is quite late in the cycle.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next
|
|
The packet hash can be considered a property of the packet, not just
on RX path.
This patch changes name of rxhash and l4_rxhash skbuff fields to be
hash and l4_hash respectively. This includes changing uses of the
field in the code which don't call the access functions.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Especially in crowded environments it can become frequent that we have
to send out whatever pending event there is stored. Since user space
has its own filtering of small RSSI changes sending a 0 value will
essentially force user space to wake up the higher layers (e.g. over
D-Bus) even though the RSSI didn't actually change more than the
threshold value.
This patch adds storing also of the RSSI for pending advertising reports
so that we report an as accurate RSSI as possible when we have to send
out the stored information to user space.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The line was incorrectly split between the variable type and its name.
This patch fixes the issue.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
To avoid too many events being sent to user space and to help parsing of
all available remote device data it makes sense for us to wait for the
scan response and send a single merged Device Found event to user space.
This patch adds a few new variables to hci_dev to track the last
received ADV_IND/ADV_SCAN_IND, i.e. those which will cause a SCAN_REQ to
be send in the case of active scanning. When the SCAN_RSP is received
the pending data is passed together with the SCAN_RSP to the
mgmt_device_found function which takes care of merging them into a
single Device Found event.
We also need a bit of extra logic to handle situations where we don't
receive a SCAN_RSP after caching some data. In such a scenario we simply
have to send out the pending data as it is and then operate on the new
report as if there was no pending data.
We also need to send out any pending data when scanning stops as
well as ensure that the storage is empty at the start of a new active
scanning session. These both cases are covered by the update to the
hci_cc_le_set_scan_enable function in this patch.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
When we're in peripheral mode (HCI_ADVERTISING flag is set) the most
natural mapping of connect() is to perform directed advertising to the
peer device.
This patch does the necessary changes to enable directed advertising and
keeps the hci_conn state as BT_CONNECT in a similar way as is done for
central or BR/EDR connection initiation.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
In preparation for being able to merge ADV_IND/ADV_SCAN_IND and SCAN_RSP
together into a single device found event add a second parameter to the
mgmt_device_found function. For now all callers pass NULL as this
parameters since we don't yet have storing of the last received
advertising report.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Conflicts:
Documentation/devicetree/bindings/net/micrel-ks8851.txt
net/core/netpoll.c
The net/core/netpoll.c conflict is a bug fix in 'net' happening
to code which is completely removed in 'net-next'.
In micrel-ks8851.txt we simply have overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next
John W. Linville says:
====================
Please pull this batch of wireless updates intended for 3.15!
For the mac80211 bits, Johannes says:
"This has a whole bunch of bugfixes for things that went into -next
previously as well as some other bugfixes I didn't want to rush into
3.14 at this point. The rest of it is some cleanups and a few small
features, the biggest of which is probably Janusz's regulatory DFS CAC
time code."
For the Bluetooth bits, Gustavo says:
"One more pull request to 3.15. This is mostly and bug fix pull request, it
contains several fixes and clean up all over the tree, plus some small new
features."
For the NFC bits, Samuel says:
"This is the NFC pull request for 3.15. With this one we have:
- Support for ISO 15693 a.k.a. NFC vicinity a.k.a. Type 5 tags. ISO
15693 are long range (1 - 2 meters) vicinity tags/cards. The kernel
now supports those through the NFC netlink and digital APIs.
- Support for TI's trf7970a chipset. This chipset relies on the NFC
digital layer and the driver currently supports type 2, 4A and 5 tags.
- Support for NXP's pn544 secure firmare download. The pn544 C3 chipsets
relies on a different firmware download protocal than the C2 one. We
now support both and use the right one depending on the version we
detect at runtime.
- Support for 4A tags from the NFC digital layer.
- A bunch of cleanups and minor fixes from Axel Lin and Thierry Escande."
For the iwlwifi bits, Emmanuel says:
"We were sending a host command while the mutex wasn't held. This
led to hard-to-catch races."
And...
"I have a fix for a "merge damage" which is not really a merge
damage: it enables scheduled scan which has been disabled in
wireless.git. Since you merged wireless.git into wireless-next.git,
this can now be fixed in wireless-next.git.
Besides this, Alex made a workaround for a hardware bug. This fix
allows us to consume less power in S3. Arik and Eliad continue to
work on D0i3 which is a run-time power saving feature. Eliad also
contributes a few bits to the rate scaling logic to which Eyal adds his
own contribution. Avri dives deep in the power code - newer firmware
will allow to enable power save in newer scenarios. Johannes made a few
clean-ups. I have the regular amount of BT Coex boring stuff. I disable
uAPSD since we identified firmware bugs that cause packet loss. One
thing that do stand out is the udev event that we now send when the
FW asserts. I hope it will allow us to debug the FW more easily."
Also included is one last iwlwifi pull for a build breakage fix...
For the Atheros bits, Kalle says:
"Michal now did some optimisations and was able to improve throughput by
100 Mbps on our MIPS based AP135 platform. Chun-Yeow added some
workarounds to be able to better use ad-hoc mode. Ben improved log
messages and added support for MSDU chaining. And, as usual, also some
smaller fixes."
Beyond that...
Andrea Merello continues his rtl8180 refactoring, in preparation for
a long-awaited rtl8187 driver. We get a new driver (rsi) for the
RS9113 chip, from Fariya Fatima. And, of course, we get the usual
round of updates for ath9k, brcmfmac, mwifiex, wil6210, etc. as well.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Simon Derr <simon.derr@bull.net>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
|
|
This request state is mostly useless, and properly implementing it
for RDMA would require an extra lock to be taken in handle_recv()
and in rdma_cancel() to avoid this race:
handle_recv() rdma_cancel()
. .
. if req->state == SENT
req->state = RCVD .
. req->state = FLSH
So just get rid of it.
Signed-off-by: Simon Derr <simon.derr@bull.net>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
|
|
And move transport-specific code out of net/9p/client.c
Signed-off-by: Simon Derr <simon.derr@bull.net>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
|
|
We need barriers to guarantee this pattern works as intended:
[w] req->rc, 1 [r] req->status, 1
wmb rmb
[w] req->status, 1 [r] req->rc
Where the wmb ensures that rc gets written before status,
and the rmb ensures that if you observe status == 1, rc is the new value.
Signed-off-by: Dominique Martinet <dominique.martinet@cea.fr>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
|
|
ip_rt_dump do nothing after IPv4 route caches removal, so we can remove it.
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When changing one 16bit value by another in IP header, we can adjust
the IP checksum by doing a simple operation described in RFC 1624, as
reminded by David.
csum_partial() is a complex function on x86_64, not really suited for
small number of checksummed bytes.
I spotted csum_partial() being in the top 20 most consuming functions
(more than 1 %) in a GRO workload, which was rather unexpected.
The caller was inet_gro_complete() doing a csum_replace2() when
building the new IP header for the GRO packet.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The LE scan type paramter defines if active scanning or passive scanning
is in use. Track the currently set value so it can be used for decision
making from other pieces in the core.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next into for-davem
|
|
While it is true that getnstimeofday() uses about 40 cycles if TSC
is available, it can use 1600 cycles if hpet is the clocksource.
Switch to get_jiffies_64(), as this is more than enough, and
go back to 60 seconds periods.
Fixes: 8c27bd75f04f ("tcp: syncookies: reduce cookie lifetime to 128 seconds")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Florian Westphal <fw@strlen.de>
Acked-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-next
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
|
|
The passkey_notify and user_confirm functions in mgmt.c were expecting
different endianess for the passkey, leading to a big endian bug and
sparse warning in recently added SMP code. This patch converts both
functions to expect host endianess and do the conversion to little
endian only when assigning to the mgmt event struct.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Add a bit in rx_status.vht_flags to let the low level driver
notify mac80211 about a beamformed packet. Propagate this
to the radiotap header.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
On 2.4Ghz band, the channels overlap since the delta
between different channels is 5Mhz while the width of the
receiver is 20Mhz (at least).
This means that we can hear beacons or probe responses from
adjacent channels. These frames will have a significant
lower RSSI which will feed all kinds of logic with inaccurate
data. An obvious example is the roaming algorithm that will
think our AP is getting weak and will try to move to another
AP.
In order to avoid this, update the signal only if the frame
has been heard on the same channel as the one advertised by
the AP in its DS / HT IEs.
We refrain from updating the values only if the AP is
already in the BSS list so that we will still have a valid
(but inaccurate) value if the AP was heard on an adjacent
channel only.
To achieve this, stop taking the channel from DS / HT IEs
in mac80211. The DS / HT IEs is taken into account to
discard the frame if it was received on a disabled channel.
This can happen due to the same phenomenon: the frame is
sent on channel 12, but heard on channel 11 while channel
12 can be disabled on certain devices. Since this check
is done in cfg80211, stop even checking this in mac80211.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
[remove unused rx_freq variable]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Drivers might want to have private data in addition
to all other ieee80211_tx_info.status fields.
The current ieee80211_tx_info.rate_driver_data overlaps
with some of the non-rate data (e.g. ampdu_ack_len), so
it might not be good enough.
Since we already know how much free bytes remained,
simply use this size to define (void *) array.
While on it, change ack_signal type from int to the more
explicit s32 type.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsec-next
Steffen Klassert says:
====================
One patch to rename a newly introduced struct. The rest is
the rework of the IPsec virtual tunnel interface for ipv6 to
support inter address family tunneling and namespace crossing.
1) Rename the newly introduced struct xfrm_filter to avoid a
conflict with iproute2. From Nicolas Dichtel.
2) Introduce xfrm_input_afinfo to access the address family
dependent tunnel callback functions properly.
3) Add and use a IPsec protocol multiplexer for ipv6.
4) Remove dst_entry caching. vti can lookup multiple different
dst entries, dependent of the configured xfrm states. Therefore
it does not make to cache a dst_entry.
5) Remove caching of flow informations. vti6 does not use the the
tunnel endpoint addresses to do route and xfrm lookups.
6) Update the vti6 to use its own receive hook.
7) Remove the now unused xfrm_tunnel_notifier. This was used from vti
and is replaced by the IPsec protocol multiplexer hooks.
8) Support inter address family tunneling for vti6.
9) Check if the tunnel endpoints of the xfrm state and the vti interface
are matching and return an error otherwise.
10) Enable namespace crossing for vti devices.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nf-next
Pablo Neira Ayuso says:
====================
Netfilter/IPVS updates for net-next
The following patchset contains Netfilter/IPVS updates for net-next,
most relevantly they are:
* cleanup to remove double semicolon from stephen hemminger.
* calm down sparse warning in xt_ipcomp, from Fan Du.
* nf_ct_labels support for nf_tables, from Florian Westphal.
* new macros to simplify rcu dereferences in the scope of nfnetlink
and nf_tables, from Patrick McHardy.
* Accept queue and drop (including reason for drop) to verdict
parsing in nf_tables, also from Patrick.
* Remove unused random seed initialization in nfnetlink_log, from
Florian Westphal.
* Allow to attach user-specific information to nf_tables rules, useful
to attach user comments to rule, from me.
* Return errors in ipset according to the manpage documentation, from
Jozsef Kadlecsik.
* Fix coccinelle warnings related to incorrect bool type usage for ipset,
from Fengguang Wu.
* Add hash:ip,mark set type to ipset, from Vytas Dauksa.
* Fix message for each spotted by ipset for each netns that is created,
from Ilia Mirkin.
* Add forceadd option to ipset, which evicts a random entry from the set
if it becomes full, from Josh Hunt.
* Minor IPVS cleanups and fixes from Andi Kleen and Tingwei Liu.
* Improve conntrack scalability by removing a central spinlock, original
work from Eric Dumazet. Jesper Dangaard Brouer took them over to address
remaining issues. Several patches to prepare this change come in first
place.
* Rework nft_hash to resolve bugs (leaking chain, missing rcu synchronization
on element removal, etc. from Patrick McHardy.
* Restore context in the rule deletion path, as we now release rule objects
synchronously, from Patrick McHardy. This gets back event notification for
anonymous sets.
* Fix NAT family validation in nft_nat, also from Patrick.
* Improve scalability of xt_connlimit by using an array of spinlocks and
by introducing a rb-tree of hashtables for faster lookup of accounted
objects per network. This patch was preceded by several patches and
refactorizations to accomodate this change including the use of kmem_cache,
from Florian Westphal.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sameo/nfc-next
Samuel Ortiz <sameo@linux.intel.com> says:
"NFC: 3.15: First pull request
This is the NFC pull request for 3.15. With this one we have:
- Support for ISO 15693 a.k.a. NFC vicinity a.k.a. Type 5 tags. ISO
15693 are long range (1 - 2 meters) vicinity tags/cards. The kernel
now supports those through the NFC netlink and digital APIs.
- Support for TI's trf7970a chipset. This chipset relies on the NFC
digital layer and the driver currently supports type 2, 4A and 5 tags.
- Support for NXP's pn544 secure firmare download. The pn544 C3 chipsets
relies on a different firmware download protocal than the C2 one. We
now support both and use the right one depending on the version we
detect at runtime.
- Support for 4A tags from the NFC digital layer.
- A bunch of cleanups and minor fixes from Axel Lin and Thierry Escande."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Conflicts:
drivers/net/usb/r8152.c
drivers/net/xen-netback/netback.c
Both the r8152 and netback conflicts were simple overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fragmentation and reassembly information for 6lowpan is independent from
the 802.15.4 stack and used only by the 6lowpan reassembly process. Move
the ieee802154_frag_info struct to a private are, it needn't be in the
802.15.4 skb control block.
Signed-off-by: Phoebe Buckheister <phoebe.buckheister@itwm.fraunhofer.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
