summaryrefslogtreecommitdiff
path: root/include/net/bluetooth
AgeCommit message (Collapse)Author
2019-05-05Bluetooth: Ignore CC events not matching the last HCI commandJoão Paulo Rechi Vita
This commit makes the kernel not send the next queued HCI command until a command complete arrives for the last HCI command sent to the controller. This change avoids a problem with some buggy controllers (seen on two SKUs of QCA9377) that send an extra command complete event for the previous command after the kernel had already sent a new HCI command to the controller. The problem was reproduced when starting an active scanning procedure, where an extra command complete event arrives for the LE_SET_RANDOM_ADDR command. When this happends the kernel ends up not processing the command complete for the following commmand, LE_SET_SCAN_PARAM, and ultimately behaving as if a passive scanning procedure was being performed, when in fact controller is performing an active scanning procedure. This makes it impossible to discover BLE devices as no device found events are sent to userspace. This problem is reproducible on 100% of the attempts on the affected controllers. The extra command complete event can be seen at timestamp 27.420131 on the btmon logs bellow. Bluetooth monitor ver 5.50 = Note: Linux version 5.0.0+ (x86_64) 0.352340 = Note: Bluetooth subsystem version 2.22 0.352343 = New Index: 80:C5:F2:8F:87:84 (Primary,USB,hci0) [hci0] 0.352344 = Open Index: 80:C5:F2:8F:87:84 [hci0] 0.352345 = Index Info: 80:C5:F2:8F:87:84 (Qualcomm) [hci0] 0.352346 @ MGMT Open: bluetoothd (privileged) version 1.14 {0x0001} 0.352347 @ MGMT Open: btmon (privileged) version 1.14 {0x0002} 0.352366 @ MGMT Open: btmgmt (privileged) version 1.14 {0x0003} 27.302164 @ MGMT Command: Start Discovery (0x0023) plen 1 {0x0003} [hci0] 27.302310 Address type: 0x06 LE Public LE Random < HCI Command: LE Set Random Address (0x08|0x0005) plen 6 #1 [hci0] 27.302496 Address: 15:60:F2:91:B2:24 (Non-Resolvable) > HCI Event: Command Complete (0x0e) plen 4 #2 [hci0] 27.419117 LE Set Random Address (0x08|0x0005) ncmd 1 Status: Success (0x00) < HCI Command: LE Set Scan Parameters (0x08|0x000b) plen 7 #3 [hci0] 27.419244 Type: Active (0x01) Interval: 11.250 msec (0x0012) Window: 11.250 msec (0x0012) Own address type: Random (0x01) Filter policy: Accept all advertisement (0x00) > HCI Event: Command Complete (0x0e) plen 4 #4 [hci0] 27.420131 LE Set Random Address (0x08|0x0005) ncmd 1 Status: Success (0x00) < HCI Command: LE Set Scan Enable (0x08|0x000c) plen 2 #5 [hci0] 27.420259 Scanning: Enabled (0x01) Filter duplicates: Enabled (0x01) > HCI Event: Command Complete (0x0e) plen 4 #6 [hci0] 27.420969 LE Set Scan Parameters (0x08|0x000b) ncmd 1 Status: Success (0x00) > HCI Event: Command Complete (0x0e) plen 4 #7 [hci0] 27.421983 LE Set Scan Enable (0x08|0x000c) ncmd 1 Status: Success (0x00) @ MGMT Event: Command Complete (0x0001) plen 4 {0x0003} [hci0] 27.422059 Start Discovery (0x0023) plen 1 Status: Success (0x00) Address type: 0x06 LE Public LE Random @ MGMT Event: Discovering (0x0013) plen 2 {0x0003} [hci0] 27.422067 Address type: 0x06 LE Public LE Random Discovery: Enabled (0x01) @ MGMT Event: Discovering (0x0013) plen 2 {0x0002} [hci0] 27.422067 Address type: 0x06 LE Public LE Random Discovery: Enabled (0x01) @ MGMT Event: Discovering (0x0013) plen 2 {0x0001} [hci0] 27.422067 Address type: 0x06 LE Public LE Random Discovery: Enabled (0x01) Signed-off-by: João Paulo Rechi Vita <jprvita@endlessm.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2019-04-25Bluetooth: Align minimum encryption key size for LE and BR/EDR connectionsMarcel Holtmann
The minimum encryption key size for LE connections is 56 bits and to align LE with BR/EDR, enforce 56 bits of minimum encryption key size for BR/EDR connections as well. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com> Cc: stable@vger.kernel.org
2019-02-26Bluetooth: Add quirk for reading BD_ADDR from fwnode propertyMatthias Kaehlcke
Add HCI_QUIRK_USE_BDADDR_PROPERTY to allow controllers to retrieve the public Bluetooth address from the firmware node property 'local-bd-address'. If quirk is set and the property does not exist or is invalid the controller is marked as unconfigured. Signed-off-by: Matthias Kaehlcke <mka@chromium.org> Reviewed-by: Balakrishna Godavarthi <bgodavar@codeaurora.org> Tested-by: Balakrishna Godavarthi <bgodavar@codeaurora.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2019-01-25Bluetooth: Allow driver specific cmd timeout handlingRajat Jain
Add a hook to allow the BT driver to do device or command specific handling in case of timeouts. This is to be used by Intel driver to reset the device after certain number of timeouts. Signed-off-by: Rajat Jain <rajatja@google.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2019-01-22Bluetooth: Fix locking in bt_accept_enqueue() for BH contextMatthias Kaehlcke
With commit e16337622016 ("Bluetooth: Handle bt_accept_enqueue() socket atomically") lock_sock[_nested]() is used to acquire the socket lock before manipulating the socket. lock_sock[_nested]() may block, which is problematic since bt_accept_enqueue() can be called in bottom half context (e.g. from rfcomm_connect_ind()): [<ffffff80080d81ec>] __might_sleep+0x4c/0x80 [<ffffff800876c7b0>] lock_sock_nested+0x24/0x58 [<ffffff8000d7c27c>] bt_accept_enqueue+0x48/0xd4 [bluetooth] [<ffffff8000e67d8c>] rfcomm_connect_ind+0x190/0x218 [rfcomm] Add a parameter to bt_accept_enqueue() to indicate whether the function is called from BH context, and acquire the socket lock with bh_lock_sock_nested() if that's the case. Also adapt all callers of bt_accept_enqueue() to pass the new parameter: - l2cap_sock_new_connection_cb() - uses lock_sock() to lock the parent socket => process context - rfcomm_connect_ind() - acquires the parent socket lock with bh_lock_sock() => BH context - __sco_chan_add() - called from sco_chan_add(), which is called from sco_connect(). parent is NULL, hence bt_accept_enqueue() isn't called in this code path and we can ignore it - also called from sco_conn_ready(). uses bh_lock_sock() to acquire the parent lock => BH context Fixes: e16337622016 ("Bluetooth: Handle bt_accept_enqueue() socket atomically") Signed-off-by: Matthias Kaehlcke <mka@chromium.org> Reviewed-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Cc: stable@vger.kernel.org
2018-10-14Bluetooth: Errata Service Release 8, Erratum 3253Mallikarjun Phulari
L2CAP: New result values 0x0006 - Connection refused – Invalid Source CID 0x0007 - Connection refused – Source CID already allocated As per the ESR08_V1.0.0, 1.11.2 Erratum 3253, Page No. 54, "Remote CID invalid Issue". Applies to Core Specification versions: V5.0, V4.2, v4.1, v4.0, and v3.0 + HS Vol 3, Part A, Section 4.2, 4.3, 4.14, 4.15. Core Specification Version 5.0, Page No.1753, Table 4.6 and Page No. 1767, Table 4.14 New result values are added to l2cap connect/create channel response as 0x0006 - Connection refused – Invalid Source CID 0x0007 - Connection refused – Source CID already allocated Signed-off-by: Mallikarjun Phulari <mallikarjun.phulari@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-10-14Bluetooth: Use separate L2CAP LE credit based connection result valuesMallikarjun Phulari
Add the result values specific to L2CAP LE credit based connections and change the old result values wherever they were used. Signed-off-by: Mallikarjun Phulari <mallikarjun.phulari@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-09-28Bluetooth: Fix debugfs NULL pointer dereferenceMatias Karhumaa
Fix crash caused by NULL pointer dereference when debugfs functions le_max_key_read, le_max_key_size_write, le_min_key_size_read or le_min_key_size_write and Bluetooth adapter was powered off. Fix is to move max_key_size and min_key_size from smp_dev to hci_dev. At the same time they were renamed to le_max_key_size and le_min_key_size. BUG: unable to handle kernel NULL pointer dereference at 00000000000002e8 PGD 0 P4D 0 Oops: 0000 [#24] SMP PTI CPU: 2 PID: 6255 Comm: cat Tainted: G D OE 4.18.9-200.fc28.x86_64 #1 Hardware name: LENOVO 4286CTO/4286CTO, BIOS 8DET76WW (1.46 ) 06/21/2018 RIP: 0010:le_max_key_size_read+0x45/0xb0 [bluetooth] Code: 00 00 00 48 83 ec 10 65 48 8b 04 25 28 00 00 00 48 89 44 24 08 31 c0 48 8b 87 c8 00 00 00 48 8d 7c 24 04 48 8b 80 48 0a 00 00 <48> 8b 80 e8 02 00 00 0f b6 48 52 e8 fb b6 b3 ed be 04 00 00 00 48 RSP: 0018:ffffab23c3ff3df0 EFLAGS: 00010246 RAX: 0000000000000000 RBX: 00007f0b4ca2e000 RCX: ffffab23c3ff3f08 RDX: ffffffffc0ddb033 RSI: 0000000000000004 RDI: ffffab23c3ff3df4 RBP: 0000000000020000 R08: 0000000000000000 R09: 0000000000000000 R10: ffffab23c3ff3ed8 R11: 0000000000000000 R12: ffffab23c3ff3f08 R13: 00007f0b4ca2e000 R14: 0000000000020000 R15: ffffab23c3ff3f08 FS: 00007f0b4ca0f540(0000) GS:ffff91bd5e280000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00000000000002e8 CR3: 00000000629fa006 CR4: 00000000000606e0 Call Trace: full_proxy_read+0x53/0x80 __vfs_read+0x36/0x180 vfs_read+0x8a/0x140 ksys_read+0x4f/0xb0 do_syscall_64+0x5b/0x160 entry_SYSCALL_64_after_hwframe+0x44/0xa9 Signed-off-by: Matias Karhumaa <matias.karhumaa@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-09-27Bluetooth: L2CAP: Derive rx credits from MTU and MPSLuiz Augusto von Dentz
Give enough rx credits for a full packet instead of using an arbitrary number which may not be enough depending on the MTU and MPS which can cause interruptions while waiting for more credits, also remove debugfs entry for l2cap_le_max_credits. With these changes the credits are restored after each SDU is received instead of using fixed threshold, this way it is garanteed that there will always be enough credits to send a packet without waiting more credits to arrive. Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-09-27Bluetooth: L2CAP: Derive MPS from connection MTULuiz Augusto von Dentz
This ensures the MPS can fit in a single HCI fragment so each segment don't have to be reassembled at HCI level, in addition to that also remove the debugfs entry to configure the MPS. Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-09-27Bluetooth: Add definitions and track LE resolve list modificationAnkit Navik
Add the definitions for adding entries to the LE resolve list and removing entries from the LE resolve list. When the LE resolve list gets changed via HCI commands make sure that the internal storage of the resolve list entries gets updated. Signed-off-by: Ankit Navik <ankit.p.navik@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-08-10Bluetooth: Add definitions for LE set address resolutionAnkit Navik
Add the definitions for LE address resolution enable HCI commands. When the LE address resolution enable gets changed via HCI commands make sure that flag gets updated. Signed-off-by: Ankit Navik <ankit.p.navik@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-08-06Bluetooth: btqca: Introduce HCI_EV_VENDOR and use itMarcel Holtmann
Using HCI_VENDOR_PKT for vendor specific events does work since it has also the value 0xff, but it is actually the packet type indicator constant and not the event constant. So introduce HCI_EV_VENDOR and use it. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2018-07-30Bluetooth: Add new quirk for non-persistent setup settingsSean Wang
Add a new quirk HCI_QUIRK_NON_PERSISTENT_SETUP allowing that a quirk that runs setup() after every open() and not just after the first open(). Signed-off-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-07-30Bluetooth: Implement secondary advertising on different PHYsJaganath Kanakkassery
This patch adds support for advertising in primary and secondary channel on different PHYs. User can add the phy preference in the flag based on which phy type will be added in extended advertising parameter would be set. @ MGMT Command: Add Advertising (0x003e) plen 11 Instance: 1 Flags: 0x00000200 Advertise in CODED on Secondary channel Duration: 0 Timeout: 0 Advertising data length: 0 Scan response length: 0 < HCI Command: LE Set Extended Advertising Enable (0x08|0x0039) plen 2 Extended advertising: Disabled (0x00) Number of sets: Disable all sets (0x00) > HCI Event: Command Complete (0x0e) plen 4 LE Set Extended Advertising Enable (0x08|0x0039) ncmd 2 Status: Success (0x00) < HCI Command: LE Set Extended Advertising Parameters (0x08|0x0036) plen 25 Handle: 0x00 Properties: 0x0000 Min advertising interval: 1280.000 msec (0x0800) Max advertising interval: 1280.000 msec (0x0800) Channel map: 37, 38, 39 (0x07) Own address type: Random (0x01) Peer address type: Public (0x00) Peer address: 00:00:00:00:00:00 (OUI 00-00-00) Filter policy: Allow Scan Request from Any, Allow Connect Request from Any (0x00) TX power: 127 dbm (0x7f) Primary PHY: LE Coded (0x03) Secondary max skip: 0x00 Secondary PHY: LE Coded (0x03) SID: 0x00 Scan request notifications: Disabled (0x00) Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-07-30Bluetooth: Handle ADv set terminated eventJaganath Kanakkassery
This event comes after connection complete event for incoming connections. Since we now have different random address for each instance, conn resp address is assigned from this event. As of now only connection part is handled as we are not enabling duration or max num of events while starting ext adv. Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-07-30Bluetooth: Implement Set ADV set random addressJaganath Kanakkassery
This basically sets the random address for the adv instance Random address can be set only if the instance is created which is done in Set ext adv param. Random address and rpa expire timer and flags have been added to adv instance which will be used when the respective instance is scheduled. This introduces a hci_get_random_address() which returns the own address type and random address (rpa or nrpa) based on the instance flags and hdev flags. New function is required since own address type should be known before setting adv params but address can be set only after setting params. < HCI Command: LE Set Advertising Set Random Address (0x08|0x0035) plen 7 Advertising handle: 0x00 Advertising random address: 3C:8E:56:9B:77:84 (OUI 3C-8E-56) > HCI Event: Command Complete (0x0e) plen 4 LE Set Advertising Set Random Address (0x08|0x0035) ncmd 1 Status: Success (0x00) Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-07-30Bluetooth: Implement disable and removal of adv instanceJaganath Kanakkassery
If ext adv is enabled then use ext adv to disable as well. Also remove the adv set during LE disable. < HCI Command: LE Set Extended Advertising Enable (0x08|0x0039) plen 2 Extended advertising: Disabled (0x00) Number of sets: Disable all sets (0x00) > HCI Event: Command Complete (0x0e) plen 4 LE Set Extended Advertising Enable (0x08|0x0039) ncmd 2 Status: Success (0x00) Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-07-30Bluetooth: Use Set ext adv/scan rsp data if controller supportsJaganath Kanakkassery
This patch implements Set Ext Adv data and Set Ext Scan rsp data if controller support extended advertising. Currently the operation is set as Complete data and fragment preference is set as no fragment < HCI Command: LE Set Extended Advertising Data (0x08|0x0037) plen 35 Handle: 0x00 Operation: Complete extended advertising data (0x03) Fragment preference: Minimize fragmentation (0x01) Data length: 0x15 16-bit Service UUIDs (complete): 2 entries Heart Rate (0x180d) Battery Service (0x180f) Name (complete): Test LE Company: Google (224) Data: 0102 > HCI Event: Command Complete (0x0e) plen 4 LE Set Extended Advertising Data (0x08|0x0037) ncmd 1 Status: Success (0x00) Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-07-30Bluetooth: Impmlement extended adv enableJaganath Kanakkassery
This patch basically replaces legacy adv with extended adv based on the controller support. Currently there is no design change. ie only one adv set will be enabled at a time. This also adds tx_power in instance and store whatever returns from Set_ext_parameter, use the same in adv data as well. For instance 0 tx_power is stored in hdev only. < HCI Command: LE Set Extended Advertising Parameters (0x08|0x0036) plen 25 Handle: 0x00 Properties: 0x0010 Use legacy advertising PDUs: ADV_NONCONN_IND Min advertising interval: 1280.000 msec (0x0800) Max advertising interval: 1280.000 msec (0x0800) Channel map: 37, 38, 39 (0x07) Own address type: Random (0x01) Peer address type: Public (0x00) Peer address: 00:00:00:00:00:00 (OUI 00-00-00) Filter policy: Allow Scan Request from Any, Allow Connect Request from Any (0x00) TX power: 127 dbm (0x7f) Primary PHY: LE 1M (0x01) Secondary max skip: 0x00 Secondary PHY: LE 1M (0x01) SID: 0x00 Scan request notifications: Disabled (0x00) > HCI Event: Command Complete (0x0e) plen 5 LE Set Extended Advertising Parameters (0x08|0x0036) ncmd 1 Status: Success (0x00) TX power (selected): 7 dbm (0x07) < HCI Command: LE Set Extended Advertising Enable (0x08|0x0039) plen 6 Extended advertising: Enabled (0x01) Number of sets: 1 (0x01) Entry 0 Handle: 0x00 Duration: 0 ms (0x00) Max ext adv events: 0 > HCI Event: Command Complete (0x0e) plen 4 LE Set Extended Advertising Enable (0x08|0x0039) ncmd 2 Status: Success (0x00) Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-07-30Bluetooth: Read no of adv sets during initJaganath Kanakkassery
This patch reads the number of advertising sets in the controller during init and save it in hdev. Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-07-30Bluetooth: Handle extended ADV PDU typesJaganath Kanakkassery
This patch defines the extended ADV types and handle it in ADV report. Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-07-30Bluetooth: Set Scan PHYs based on selected PHYs by userJaganath Kanakkassery
Use the PHYs selected in Set Phy Configuration management command while scanning. < HCI Command: LE Set Extended Scan Parameters (0x08|0x0041) plen 13 Own address type: Random (0x01) Filter policy: Accept all advertisement (0x00) PHYs: 0x05 Entry 0: LE 1M Type: Active (0x01) Interval: 11.250 msec (0x0012) Window: 11.250 msec (0x0012) Entry 1: LE Coded Type: Active (0x01) Interval: 11.250 msec (0x0012) Window: 11.250 msec (0x0012) > HCI Event: Command Complete (0x0e) plen 4 LE Set Extended Scan Parameters (0x08|0x0041) ncmd 1 Status: Success (0x00) < HCI Command: LE Set Extended Scan Enable (0x08|0x0042) plen 6 Extended scan: Enabled (0x01) Filter duplicates: Enabled (0x01) Duration: 0 msec (0x0000) Period: 0.00 sec (0x0000) > HCI Event: Command Complete (0x0e) plen 4 LE Set Extended Scan Enable (0x08|0x0042) ncmd 2 Status: Success (0x00) Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-07-30Bluetooth: Implement PHY changed eventJaganath Kanakkassery
This defines and implement phy changed event and send it to user whenever selected PHYs changes using SET_PHY_CONFIGURATION. This will be also trigerred when BREDR pkt_type is changed using the legacy ioctl HCISETPTYPE. @ MGMT Command: Set PHY Configuration (0x0045) plen 4 Selected PHYs: 0x7fff BR 1M 1SLOT BR 1M 3SLOT BR 1M 5SLOT EDR 2M 1SLOT EDR 2M 3SLOT EDR 2M 5SLOT EDR 3M 1SLOT EDR 3M 3SLOT EDR 3M 5SLOT LE 1M TX LE 1M RX LE 2M TX LE 2M RX LE CODED TX LE CODED RX < HCI Command: LE Set Default PHY (0x08|0x0031) plen 3 All PHYs preference: 0x00 TX PHYs preference: 0x07 LE 1M LE 2M LE Coded RX PHYs preference: 0x07 LE 1M LE 2M LE Coded > HCI Event: Command Complete (0x0e) plen 4 LE Set Default PHY (0x08|0x0031) ncmd 1 Status: Success (0x00) @ MGMT Event: Command Complete (0x0001) plen 3 Set PHY Configuration (0x0045) plen 0 Status: Success (0x00) @ MGMT Event: PHY Configuration Changed (0x0026) plen 4 Selected PHYs: 0x7fff BR 1M 1SLOT BR 1M 3SLOT BR 1M 5SLOT EDR 2M 1SLOT EDR 2M 3SLOT EDR 2M 5SLOT EDR 3M 1SLOT EDR 3M 3SLOT EDR 3M 5SLOT LE 1M TX LE 1M RX LE 2M TX LE 2M RX LE CODED TX LE CODED RX Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-07-30Bluetooth: Implement Set PHY Confguration commandJaganath Kanakkassery
This enables user to set phys which will be used in all subsequent connections. Also host will use the same in LE scanning as well. @ MGMT Command: Set PHY Configuration (0x0045) plen 4 Selected PHYs: 0x7fff BR 1M 1SLOT BR 1M 3SLOT BR 1M 5SLOT EDR 2M 1SLOT EDR 2M 3SLOT EDR 2M 5SLOT EDR 3M 1SLOT EDR 3M 3SLOT EDR 3M 5SLOT LE 1M TX LE 1M RX LE 2M TX LE 2M RX LE CODED TX LE CODED RX < HCI Command: LE Set Default PHY (0x08|0x0031) plen 3 All PHYs preference: 0x00 TX PHYs preference: 0x07 LE 1M LE 2M LE Coded RX PHYs preference: 0x07 LE 1M LE 2M LE Coded > HCI Event: Command Complete (0x0e) plen 4 LE Set Default PHY (0x08|0x0031) ncmd 1 Status: Success (0x00) @ MGMT Event: Command Complete (0x0001) plen 3 Set PHY Configuration (0x0045) plen 0 Status: Success (0x00) @ MGMT Event: PHY Configuration Changed (0x0026) plen 4 Selected PHYs: 0x7fff BR 1M 1SLOT BR 1M 3SLOT BR 1M 5SLOT EDR 2M 1SLOT EDR 2M 3SLOT EDR 2M 5SLOT EDR 3M 1SLOT EDR 3M 3SLOT EDR 3M 5SLOT LE 1M TX LE 1M RX LE 2M TX LE 2M RX LE CODED TX LE CODED RX Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-07-30Bluetooth: Implement Get PHY Configuration mgmt commandJaganath Kanakkassery
This commands basically retrieve the supported packet types of BREDR and supported PHYs of the controller. BR_1M_1SLOT, LE_1M_TX and LE_1M_RX would be supported by default. Other PHYs are supported based on the local features. Also this sets PHY_CONFIGURATION bit in supported settings. @ MGMT Command: Get PHY Configuration (0x0044) plen 0 @ MGMT Event: Command Complete (0x0001) plen 15 Get PHY Configuration (0x0044) plen 12 Status: Success (0x00) Supported PHYs: 0x7fff BR 1M 1SLOT BR 1M 3SLOT BR 1M 5SLOT EDR 2M 1SLOT EDR 2M 3SLOT EDR 2M 5SLOT EDR 3M 1SLOT EDR 3M 3SLOT EDR 3M 5SLOT LE 1M TX LE 1M RX LE 2M TX LE 2M RX LE CODED TX LE CODED RX Configurable PHYs: 0x79fe BR 1M 3SLOT BR 1M 5SLOT EDR 2M 1SLOT EDR 2M 3SLOT EDR 2M 5SLOT EDR 3M 1SLOT EDR 3M 3SLOT EDR 3M 5SLOT LE 2M TX LE 2M RX LE CODED TX LE CODED RX Selected PHYs: 0x07ff BR 1M 1SLOT BR 1M 3SLOT BR 1M 5SLOT EDR 2M 1SLOT EDR 2M 3SLOT EDR 2M 5SLOT EDR 3M 1SLOT EDR 3M 3SLOT EDR 3M 5SLOT LE 1M TX LE 1M RX Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-07-30Bluetooth: Add defines for BREDR pkt_type and LE PHYsJaganath Kanakkassery
This also add macros for checking LMP support for different pkt_types Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-07-30Bluetooth: Define PHY flags in hdev and set 1M as defaultJaganath Kanakkassery
1M is mandatory to be supported by LE controllers and the same would be set in power on. This patch defines hdev flags for LE PHYs and set 1M to default. Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-07-06Bluetooth: Use extended LE Connection if supportedJaganath Kanakkassery
This implements extended LE craete connection and enhanced LE conn complete event if the controller supports. For now it is as good as legacy LE connection and event as no new features in the extended connection is handled. < HCI Command: LE Extended Create Connection (0x08|0x0043) plen 26 Filter policy: White list is not used (0x00) Own address type: Public (0x00) Peer address type: Random (0x01) Peer address: DB:7E:2E:1D:85:E8 (Static) Initiating PHYs: 0x01 Entry 0: LE 1M Scan interval: 60.000 msec (0x0060) Scan window: 60.000 msec (0x0060) Min connection interval: 50.00 msec (0x0028) Max connection interval: 70.00 msec (0x0038) Connection latency: 0 (0x0000) Supervision timeout: 420 msec (0x002a) Min connection length: 0.000 msec (0x0000) Max connection length: 0.000 msec (0x0000) > HCI Event: Command Status (0x0f) plen 4 LE Extended Create Connection (0x08|0x0043) ncmd 2 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 31 LE Enhanced Connection Complete (0x0a) Status: Success (0x00) Handle: 3585 Role: Master (0x00) Peer address type: Random (0x01) Peer address: DB:7E:2E:1D:85:E8 (Static) Local resolvable private address: 00:00:00:00:00:00 (Non-Resolvable) Peer resolvable private address: 00:00:00:00:00:00 (Non-Resolvable) Connection interval: 67.50 msec (0x0036) Connection latency: 0 (0x0000) Supervision timeout: 420 msec (0x002a) Master clock accuracy: 0x00 @ MGMT Event: Device Connected (0x000b) plen 40 LE Address: DB:7E:2E:1D:85:E8 (Static) Flags: 0x00000000 Data length: 27 Name (complete): Designer Mouse Appearance: Mouse (0x03c2) Flags: 0x05 LE Limited Discoverable Mode BR/EDR Not Supported 16-bit Service UUIDs (complete): 1 entry Human Interface Device (0x1812) Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-07-06Bluetooth: Process extended ADV report eventJaganath Kanakkassery
This patch enables Extended ADV report event if extended scanning is supported in the controller and process the same. The new features are not handled and for now its as good as legacy ADV report. > HCI Event: LE Meta Event (0x3e) plen 53 LE Extended Advertising Report (0x0d) Num reports: 1 Entry 0 Event type: 0x0013 Props: 0x0013 Connectable Scannable Use legacy advertising PDUs Data status: Complete Legacy PDU Type: ADV_IND (0x0013) Address type: Random (0x01) Address: DB:7E:2E:1A:85:E8 (Static) Primary PHY: LE 1M Secondary PHY: LE 1M SID: 0x00 TX power: 0 dBm RSSI: -90 dBm (0xa6) Periodic advertising invteral: 0.00 msec (0x0000) Direct address type: Public (0x00) Direct address: 00:00:00:00:00:00 (OUI 00-00-00) Data length: 0x1b 0f 09 44 65 73 69 67 6e 65 72 20 4d 6f 75 73 65 ..Designer Mouse 03 19 c2 03 02 01 05 03 03 12 18 ........... Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-07-06Bluetooth: Use extended scanning if controller supportsJaganath Kanakkassery
This implements Set extended scan param and set extended scan enable commands and use it for start LE scan based on controller support. The new features added in these commands are setting of new PHY for scanning and setting of scan duration. Both features are disabled for now, meaning only 1M PHY is set and scan duration is set to 0 which means that scanning will be done untill scan disable is called. < HCI Command: LE Set Extended Scan Parameters (0x08|0x0041) plen 8 Own address type: Random (0x01) Filter policy: Accept all advertisement (0x00) PHYs: 0x01 Entry 0: LE 1M Type: Active (0x01) Interval: 11.250 msec (0x0012) Window: 11.250 msec (0x0012) > HCI Event: Command Complete (0x0e) plen 4 LE Set Extended Scan Parameters (0x08|0x0041) ncmd 1 Status: Success (0x00) < HCI Command: LE Set Extended Scan Enable (0x08|0x0042) plen 6 Extended scan: Enabled (0x01) Filter duplicates: Enabled (0x01) Duration: 0 msec (0x0000) Period: 0.00 sec (0x0000) > HCI Event: Command Complete (0x0e) plen 4 LE Set Extended Scan Enable (0x08|0x0042) ncmd 2 Status: Success (0x00) Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-07-06Bluetooth: Add HCI command for clear Resolv listAnkit Navik
Check for Resolv list supported by controller. So check the supported commmand first before issuing this command i.e.,HCI_OP_LE_CLEAR_RESOLV_LIST Before patch: < HCI Command: LE Read White List... (0x08|0x000f) plen 0 #55 [hci0] 13.338168 > HCI Event: Command Complete (0x0e) plen 5 #56 [hci0] 13.338842 LE Read White List Size (0x08|0x000f) ncmd 1 Status: Success (0x00) Size: 25 < HCI Command: LE Clear White List (0x08|0x0010) plen 0 #57 [hci0] 13.339029 > HCI Event: Command Complete (0x0e) plen 4 #58 [hci0] 13.339939 LE Clear White List (0x08|0x0010) ncmd 1 Status: Success (0x00) < HCI Command: LE Read Resolving L.. (0x08|0x002a) plen 0 #59 [hci0] 13.340152 > HCI Event: Command Complete (0x0e) plen 5 #60 [hci0] 13.340952 LE Read Resolving List Size (0x08|0x002a) ncmd 1 Status: Success (0x00) Size: 25 < HCI Command: LE Read Maximum Dat.. (0x08|0x002f) plen 0 #61 [hci0] 13.341180 > HCI Event: Command Complete (0x0e) plen 12 #62 [hci0] 13.341898 LE Read Maximum Data Length (0x08|0x002f) ncmd 1 Status: Success (0x00) Max TX octets: 251 Max TX time: 17040 Max RX octets: 251 Max RX time: 17040 After patch: < HCI Command: LE Read White List... (0x08|0x000f) plen 0 #55 [hci0] 28.919131 > HCI Event: Command Complete (0x0e) plen 5 #56 [hci0] 28.920016 LE Read White List Size (0x08|0x000f) ncmd 1 Status: Success (0x00) Size: 25 < HCI Command: LE Clear White List (0x08|0x0010) plen 0 #57 [hci0] 28.920164 > HCI Event: Command Complete (0x0e) plen 4 #58 [hci0] 28.920873 LE Clear White List (0x08|0x0010) ncmd 1 Status: Success (0x00) < HCI Command: LE Read Resolving L.. (0x08|0x002a) plen 0 #59 [hci0] 28.921109 > HCI Event: Command Complete (0x0e) plen 5 #60 [hci0] 28.922016 LE Read Resolving List Size (0x08|0x002a) ncmd 1 Status: Success (0x00) Size: 25 < HCI Command: LE Clear Resolving... (0x08|0x0029) plen 0 #61 [hci0] 28.922166 > HCI Event: Command Complete (0x0e) plen 4 #62 [hci0] 28.922872 LE Clear Resolving List (0x08|0x0029) ncmd 1 Status: Success (0x00) < HCI Command: LE Read Maximum Dat.. (0x08|0x002f) plen 0 #63 [hci0] 28.923117 > HCI Event: Command Complete (0x0e) plen 12 #64 [hci0] 28.924030 LE Read Maximum Data Length (0x08|0x002f) ncmd 1 Status: Success (0x00) Max TX octets: 251 Max TX time: 17040 Max RX octets: 251 Max RX time: 17040 Signed-off-by: Ankit Navik <ankit.p.navik@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-07-06Bluetooth: Store Resolv list sizeAnkit Navik
When the controller supports the Read LE Resolv List size feature, the maximum list size are read and now stored. Before patch: < HCI Command: LE Read White List... (0x08|0x000f) plen 0 #55 [hci0] 17.979791 > HCI Event: Command Complete (0x0e) plen 5 #56 [hci0] 17.980629 LE Read White List Size (0x08|0x000f) ncmd 1 Status: Success (0x00) Size: 25 < HCI Command: LE Clear White List (0x08|0x0010) plen 0 #57 [hci0] 17.980786 > HCI Event: Command Complete (0x0e) plen 4 #58 [hci0] 17.981627 LE Clear White List (0x08|0x0010) ncmd 1 Status: Success (0x00) < HCI Command: LE Read Maximum Dat.. (0x08|0x002f) plen 0 #59 [hci0] 17.981786 > HCI Event: Command Complete (0x0e) plen 12 #60 [hci0] 17.982636 LE Read Maximum Data Length (0x08|0x002f) ncmd 1 Status: Success (0x00) Max TX octets: 251 Max TX time: 17040 Max RX octets: 251 Max RX time: 17040 After patch: < HCI Command: LE Read White List... (0x08|0x000f) plen 0 #55 [hci0] 13.338168 > HCI Event: Command Complete (0x0e) plen 5 #56 [hci0] 13.338842 LE Read White List Size (0x08|0x000f) ncmd 1 Status: Success (0x00) Size: 25 < HCI Command: LE Clear White List (0x08|0x0010) plen 0 #57 [hci0] 13.339029 > HCI Event: Command Complete (0x0e) plen 4 #58 [hci0] 13.339939 LE Clear White List (0x08|0x0010) ncmd 1 Status: Success (0x00) < HCI Command: LE Read Resolving L.. (0x08|0x002a) plen 0 #59 [hci0] 13.340152 > HCI Event: Command Complete (0x0e) plen 5 #60 [hci0] 13.340952 LE Read Resolving List Size (0x08|0x002a) ncmd 1 Status: Success (0x00) Size: 25 < HCI Command: LE Read Maximum Dat.. (0x08|0x002f) plen 0 #61 [hci0] 13.341180 > HCI Event: Command Complete (0x0e) plen 12 #62 [hci0] 13.341898 LE Read Maximum Data Length (0x08|0x002f) ncmd 1 Status: Success (0x00) Max TX octets: 251 Max TX time: 17040 Max RX octets: 251 Max RX time: 17040 Signed-off-by: Ankit Navik <ankit.p.navik@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-06-28Revert changes to convert to ->poll_mask() and aio IOCB_CMD_POLLLinus Torvalds
The poll() changes were not well thought out, and completely unexplained. They also caused a huge performance regression, because "->poll()" was no longer a trivial file operation that just called down to the underlying file operations, but instead did at least two indirect calls. Indirect calls are sadly slow now with the Spectre mitigation, but the performance problem could at least be largely mitigated by changing the "->get_poll_head()" operation to just have a per-file-descriptor pointer to the poll head instead. That gets rid of one of the new indirections. But that doesn't fix the new complexity that is completely unwarranted for the regular case. The (undocumented) reason for the poll() changes was some alleged AIO poll race fixing, but we don't make the common case slower and more complex for some uncommon special case, so this all really needs way more explanations and most likely a fundamental redesign. [ This revert is a revert of about 30 different commits, not reverted individually because that would just be unnecessarily messy - Linus ] Cc: Al Viro <viro@zeniv.linux.org.uk> Cc: Christoph Hellwig <hch@lst.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2018-06-06Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-nextLinus Torvalds
Pull networking updates from David Miller: 1) Add Maglev hashing scheduler to IPVS, from Inju Song. 2) Lots of new TC subsystem tests from Roman Mashak. 3) Add TCP zero copy receive and fix delayed acks and autotuning with SO_RCVLOWAT, from Eric Dumazet. 4) Add XDP_REDIRECT support to mlx5 driver, from Jesper Dangaard Brouer. 5) Add ttl inherit support to vxlan, from Hangbin Liu. 6) Properly separate ipv6 routes into their logically independant components. fib6_info for the routing table, and fib6_nh for sets of nexthops, which thus can be shared. From David Ahern. 7) Add bpf_xdp_adjust_tail helper, which can be used to generate ICMP messages from XDP programs. From Nikita V. Shirokov. 8) Lots of long overdue cleanups to the r8169 driver, from Heiner Kallweit. 9) Add BTF ("BPF Type Format"), from Martin KaFai Lau. 10) Add traffic condition monitoring to iwlwifi, from Luca Coelho. 11) Plumb extack down into fib_rules, from Roopa Prabhu. 12) Add Flower classifier offload support to igb, from Vinicius Costa Gomes. 13) Add UDP GSO support, from Willem de Bruijn. 14) Add documentation for eBPF helpers, from Quentin Monnet. 15) Add TLS tx offload to mlx5, from Ilya Lesokhin. 16) Allow applications to be given the number of bytes available to read on a socket via a control message returned from recvmsg(), from Soheil Hassas Yeganeh. 17) Add x86_32 eBPF JIT compiler, from Wang YanQing. 18) Add AF_XDP sockets, with zerocopy support infrastructure as well. From Björn Töpel. 19) Remove indirect load support from all of the BPF JITs and handle these operations in the verifier by translating them into native BPF instead. From Daniel Borkmann. 20) Add GRO support to ipv6 gre tunnels, from Eran Ben Elisha. 21) Allow XDP programs to do lookups in the main kernel routing tables for forwarding. From David Ahern. 22) Allow drivers to store hardware state into an ELF section of kernel dump vmcore files, and use it in cxgb4. From Rahul Lakkireddy. 23) Various RACK and loss detection improvements in TCP, from Yuchung Cheng. 24) Add TCP SACK compression, from Eric Dumazet. 25) Add User Mode Helper support and basic bpfilter infrastructure, from Alexei Starovoitov. 26) Support ports and protocol values in RTM_GETROUTE, from Roopa Prabhu. 27) Support bulking in ->ndo_xdp_xmit() API, from Jesper Dangaard Brouer. 28) Add lots of forwarding selftests, from Petr Machata. 29) Add generic network device failover driver, from Sridhar Samudrala. * ra.kernel.org:/pub/scm/linux/kernel/git/davem/net-next: (1959 commits) strparser: Add __strp_unpause and use it in ktls. rxrpc: Fix terminal retransmission connection ID to include the channel net: hns3: Optimize PF CMDQ interrupt switching process net: hns3: Fix for VF mailbox receiving unknown message net: hns3: Fix for VF mailbox cannot receiving PF response bnx2x: use the right constant Revert "net: sched: cls: Fix offloading when ingress dev is vxlan" net: dsa: b53: Fix for brcm tag issue in Cygnus SoC enic: fix UDP rss bits netdev-FAQ: clarify DaveM's position for stable backports rtnetlink: validate attributes in do_setlink() mlxsw: Add extack messages for port_{un, }split failures netdevsim: Add extack error message for devlink reload devlink: Add extack to reload and port_{un, }split operations net: metrics: add proper netlink validation ipmr: fix error path when ipmr_new_table fails ip6mr: only set ip6mr_table from setsockopt when ip6mr_new_table succeeds net: hns3: remove unused hclgevf_cfg_func_mta_filter netfilter: provide udp*_lib_lookup for nf_tproxy qed*: Utilize FW 8.37.2.0 ...
2018-05-26net/bluetooth: convert to ->poll_maskChristoph Hellwig
Signed-off-by: Christoph Hellwig <hch@lst.de>
2018-05-18Bluetooth: Add __hci_cmd_send functionLoic Poulain
This function allows to send a HCI command without expecting any controller event/response in return. This is allowed for vendor- specific commands only. Signed-off-by: Loic Poulain <loic.poulain@linaro.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-04-08Merge branch 'for-upstream' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth Johan Hedberg says: ==================== pull request: bluetooth 2018-04-08 Here's one important Bluetooth fix for the 4.17-rc series that's needed to pass several Bluetooth qualification test cases. Let me know if there are any issues pulling. Thanks. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2018-04-03Bluetooth: Fix connection if directed advertising and privacy is usedSzymon Janc
Local random address needs to be updated before creating connection if RPA from LE Direct Advertising Report was resolved in host. Otherwise remote device might ignore connection request due to address mismatch. This was affecting following qualification test cases: GAP/CONN/SCEP/BV-03-C, GAP/CONN/GCEP/BV-05-C, GAP/CONN/DCEP/BV-05-C Before patch: < HCI Command: LE Set Random Address (0x08|0x0005) plen 6 #11350 [hci0] 84680.231216 Address: 56:BC:E8:24:11:68 (Resolvable) Identity type: Random (0x01) Identity: F2:F1:06:3D:9C:42 (Static) > HCI Event: Command Complete (0x0e) plen 4 #11351 [hci0] 84680.246022 LE Set Random Address (0x08|0x0005) ncmd 1 Status: Success (0x00) < HCI Command: LE Set Scan Parameters (0x08|0x000b) plen 7 #11352 [hci0] 84680.246417 Type: Passive (0x00) Interval: 60.000 msec (0x0060) Window: 30.000 msec (0x0030) Own address type: Random (0x01) Filter policy: Accept all advertisement, inc. directed unresolved RPA (0x02) > HCI Event: Command Complete (0x0e) plen 4 #11353 [hci0] 84680.248854 LE Set Scan Parameters (0x08|0x000b) ncmd 1 Status: Success (0x00) < HCI Command: LE Set Scan Enable (0x08|0x000c) plen 2 #11354 [hci0] 84680.249466 Scanning: Enabled (0x01) Filter duplicates: Enabled (0x01) > HCI Event: Command Complete (0x0e) plen 4 #11355 [hci0] 84680.253222 LE Set Scan Enable (0x08|0x000c) ncmd 1 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 18 #11356 [hci0] 84680.458387 LE Direct Advertising Report (0x0b) Num reports: 1 Event type: Connectable directed - ADV_DIRECT_IND (0x01) Address type: Random (0x01) Address: 53:38:DA:46:8C:45 (Resolvable) Identity type: Public (0x00) Identity: 11:22:33:44:55:66 (OUI 11-22-33) Direct address type: Random (0x01) Direct address: 7C:D6:76:8C:DF:82 (Resolvable) Identity type: Random (0x01) Identity: F2:F1:06:3D:9C:42 (Static) RSSI: -74 dBm (0xb6) < HCI Command: LE Set Scan Enable (0x08|0x000c) plen 2 #11357 [hci0] 84680.458737 Scanning: Disabled (0x00) Filter duplicates: Disabled (0x00) > HCI Event: Command Complete (0x0e) plen 4 #11358 [hci0] 84680.469982 LE Set Scan Enable (0x08|0x000c) ncmd 1 Status: Success (0x00) < HCI Command: LE Create Connection (0x08|0x000d) plen 25 #11359 [hci0] 84680.470444 Scan interval: 60.000 msec (0x0060) Scan window: 60.000 msec (0x0060) Filter policy: White list is not used (0x00) Peer address type: Random (0x01) Peer address: 53:38:DA:46:8C:45 (Resolvable) Identity type: Public (0x00) Identity: 11:22:33:44:55:66 (OUI 11-22-33) Own address type: Random (0x01) Min connection interval: 30.00 msec (0x0018) Max connection interval: 50.00 msec (0x0028) Connection latency: 0 (0x0000) Supervision timeout: 420 msec (0x002a) Min connection length: 0.000 msec (0x0000) Max connection length: 0.000 msec (0x0000) > HCI Event: Command Status (0x0f) plen 4 #11360 [hci0] 84680.474971 LE Create Connection (0x08|0x000d) ncmd 1 Status: Success (0x00) < HCI Command: LE Create Connection Cancel (0x08|0x000e) plen 0 #11361 [hci0] 84682.545385 > HCI Event: Command Complete (0x0e) plen 4 #11362 [hci0] 84682.551014 LE Create Connection Cancel (0x08|0x000e) ncmd 1 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 19 #11363 [hci0] 84682.551074 LE Connection Complete (0x01) Status: Unknown Connection Identifier (0x02) Handle: 0 Role: Master (0x00) Peer address type: Public (0x00) Peer address: 00:00:00:00:00:00 (OUI 00-00-00) Connection interval: 0.00 msec (0x0000) Connection latency: 0 (0x0000) Supervision timeout: 0 msec (0x0000) Master clock accuracy: 0x00 After patch: < HCI Command: LE Set Scan Parameters (0x08|0x000b) plen 7 #210 [hci0] 667.152459 Type: Passive (0x00) Interval: 60.000 msec (0x0060) Window: 30.000 msec (0x0030) Own address type: Random (0x01) Filter policy: Accept all advertisement, inc. directed unresolved RPA (0x02) > HCI Event: Command Complete (0x0e) plen 4 #211 [hci0] 667.153613 LE Set Scan Parameters (0x08|0x000b) ncmd 1 Status: Success (0x00) < HCI Command: LE Set Scan Enable (0x08|0x000c) plen 2 #212 [hci0] 667.153704 Scanning: Enabled (0x01) Filter duplicates: Enabled (0x01) > HCI Event: Command Complete (0x0e) plen 4 #213 [hci0] 667.154584 LE Set Scan Enable (0x08|0x000c) ncmd 1 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 18 #214 [hci0] 667.182619 LE Direct Advertising Report (0x0b) Num reports: 1 Event type: Connectable directed - ADV_DIRECT_IND (0x01) Address type: Random (0x01) Address: 50:52:D9:A6:48:A0 (Resolvable) Identity type: Public (0x00) Identity: 11:22:33:44:55:66 (OUI 11-22-33) Direct address type: Random (0x01) Direct address: 7C:C1:57:A5:B7:A8 (Resolvable) Identity type: Random (0x01) Identity: F4:28:73:5D:38:B0 (Static) RSSI: -70 dBm (0xba) < HCI Command: LE Set Scan Enable (0x08|0x000c) plen 2 #215 [hci0] 667.182704 Scanning: Disabled (0x00) Filter duplicates: Disabled (0x00) > HCI Event: Command Complete (0x0e) plen 4 #216 [hci0] 667.183599 LE Set Scan Enable (0x08|0x000c) ncmd 1 Status: Success (0x00) < HCI Command: LE Set Random Address (0x08|0x0005) plen 6 #217 [hci0] 667.183645 Address: 7C:C1:57:A5:B7:A8 (Resolvable) Identity type: Random (0x01) Identity: F4:28:73:5D:38:B0 (Static) > HCI Event: Command Complete (0x0e) plen 4 #218 [hci0] 667.184590 LE Set Random Address (0x08|0x0005) ncmd 1 Status: Success (0x00) < HCI Command: LE Create Connection (0x08|0x000d) plen 25 #219 [hci0] 667.184613 Scan interval: 60.000 msec (0x0060) Scan window: 60.000 msec (0x0060) Filter policy: White list is not used (0x00) Peer address type: Random (0x01) Peer address: 50:52:D9:A6:48:A0 (Resolvable) Identity type: Public (0x00) Identity: 11:22:33:44:55:66 (OUI 11-22-33) Own address type: Random (0x01) Min connection interval: 30.00 msec (0x0018) Max connection interval: 50.00 msec (0x0028) Connection latency: 0 (0x0000) Supervision timeout: 420 msec (0x002a) Min connection length: 0.000 msec (0x0000) Max connection length: 0.000 msec (0x0000) > HCI Event: Command Status (0x0f) plen 4 #220 [hci0] 667.186558 LE Create Connection (0x08|0x000d) ncmd 1 Status: Success (0x00) > HCI Event: LE Meta Event (0x3e) plen 19 #221 [hci0] 667.485824 LE Connection Complete (0x01) Status: Success (0x00) Handle: 0 Role: Master (0x00) Peer address type: Random (0x01) Peer address: 50:52:D9:A6:48:A0 (Resolvable) Identity type: Public (0x00) Identity: 11:22:33:44:55:66 (OUI 11-22-33) Connection interval: 50.00 msec (0x0028) Connection latency: 0 (0x0000) Supervision timeout: 420 msec (0x002a) Master clock accuracy: 0x07 @ MGMT Event: Device Connected (0x000b) plen 13 {0x0002} [hci0] 667.485996 LE Address: 11:22:33:44:55:66 (OUI 11-22-33) Flags: 0x00000000 Data length: 0 Signed-off-by: Szymon Janc <szymon.janc@codecoup.pl> Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Cc: stable@vger.kernel.org
2018-04-01Bluetooth: Fix data type of appearenceJaganath Kanakkassery
It should be __le16 instead of __u16 since its part of mgmt API. Signed-off-by: Jaganath Kanakkassery <jaganathx.kanakkassery@intel.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2017-11-27net: annotate ->poll() instancesAl Viro
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
2017-10-30Bluetooth: Use bt_dev_err and bt_dev_info when possibleMarcel Holtmann
In case of using BT_ERR and BT_INFO, convert to bt_dev_err and bt_dev_info when possible. This allows for controller specific reporting. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2017-10-29Bluetooth: increase timeout for le auto connectionsKonrad Zapałowicz
This patch increases the connection timeout for LE connections that are triggered by the advertising report to 4 seconds. It has been observed that devices equipped with wifi+bt combo SoC fail to create a connection with BLE devices due to their coexistence issues. Increasing this timeout gives them enough time to complete the connection with success. Signed-off-by: Konrad Zapałowicz <konrad.zapalowicz@canonical.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2017-09-01Bluetooth: make baswap src constLoic Poulain
Signed-off-by: Loic Poulain <loic.poulain@linaro.org> Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2017-05-18Bluetooth: Set LE Default PHY preferencesMarcel Holtmann
If the LE Set Default PHY command is supported, the indicate to the controller that the host has no preferences for transmitter PHY or receiver PHY selection. Issuing this command gives the controller a clear indication that other PHY can be selected if available. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2017-05-18Bluetooth: Enable LE Channel Selection Algorithm eventMarcel Holtmann
If the Channel Selection Algorithm #2 feature is supported, then enable the new LE Channel Selection Algorithm event. Signed-off-by: Marcel Holtmann <marcel@holtmann.org> Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
2017-04-12Bluetooth: L2CAP: Fix L2CAP_CR_SCID_IN_USE valueMarcin Kraglak
Fix issue found during L2CAP qualification test TP/LE/CFC/BV-20-C. Signed-off-by: Marcin Kraglak <marcin.kraglak@tieto.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2017-04-12Bluetooth: convert rfcomm_dlc.refcnt from atomic_t to refcount_tElena Reshetova
refcount_t type and corresponding API should be used instead of atomic_t when the variable is used as a reference counter. This allows to avoid accidental refcounter overflows that might lead to use-after-free situations. Signed-off-by: Elena Reshetova <elena.reshetova@intel.com> Signed-off-by: Hans Liljestrand <ishkamiel@gmail.com> Signed-off-by: Kees Cook <keescook@chromium.org> Signed-off-by: David Windsor <dwindsor@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2017-03-02sched/headers: Prepare to use <linux/rcuupdate.h> instead of ↵Ingo Molnar
<linux/rculist.h> in <linux/sched.h> We don't actually need the full rculist.h header in sched.h anymore, we will be able to include the smaller rcupdate.h header instead. But first update code that relied on the implicit header inclusion. Acked-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: Mike Galbraith <efault@gmx.de> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-kernel@vger.kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org>
2017-01-14locking/atomic, kref: Add kref_read()Peter Zijlstra
Since we need to change the implementation, stop exposing internals. Provide kref_read() to read the current reference count; typically used for debug messages. Kills two anti-patterns: atomic_read(&kref->refcount) kref->refcount.counter Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-kernel@vger.kernel.org Signed-off-by: Ingo Molnar <mingo@kernel.org>
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-15 07:35:41 +0000