| Age | Commit message (Collapse) | Author |
|---|
|
Pull rdma updates from Jason Gunthorpe:
"A usual cycle for RDMA with a typical mix of driver and core subsystem
updates:
- Driver minor changes and bug fixes for mlx5, efa, rxe, vmw_pvrdma,
hns, usnic, qib, qedr, cxgb4, hns, bnxt_re
- Various rtrs fixes and updates
- Bug fix for mlx4 CM emulation for virtualization scenarios where
MRA wasn't working right
- Use tracepoints instead of pr_debug in the CM code
- Scrub the locking in ucma and cma to close more syzkaller bugs
- Use tasklet_setup in the subsystem
- Revert the idea that 'destroy' operations are not allowed to fail
at the driver level. This proved unworkable from a HW perspective.
- Revise how the umem API works so drivers make fewer mistakes using
it
- XRC support for qedr
- Convert uverbs objects RWQ and MW to new the allocation scheme
- Large queue entry sizes for hns
- Use hmm_range_fault() for mlx5 On Demand Paging
- uverbs APIs to inspect the GID table instead of sysfs
- Move some of the RDMA code for building large page SGLs into
lib/scatterlist"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (191 commits)
RDMA/ucma: Fix use after free in destroy id flow
RDMA/rxe: Handle skb_clone() failure in rxe_recv.c
RDMA/rxe: Move the definitions for rxe_av.network_type to uAPI
RDMA: Explicitly pass in the dma_device to ib_register_device
lib/scatterlist: Do not limit max_segment to PAGE_ALIGNED values
IB/mlx4: Convert rej_tmout radix-tree to XArray
RDMA/rxe: Fix bug rejecting all multicast packets
RDMA/rxe: Fix skb lifetime in rxe_rcv_mcast_pkt()
RDMA/rxe: Remove duplicate entries in struct rxe_mr
IB/hfi,rdmavt,qib,opa_vnic: Update MAINTAINERS
IB/rdmavt: Fix sizeof mismatch
MAINTAINERS: CISCO VIC LOW LATENCY NIC DRIVER
RDMA/bnxt_re: Fix sizeof mismatch for allocation of pbl_tbl.
RDMA/bnxt_re: Use rdma_umem_for_each_dma_block()
RDMA/umem: Move to allocate SG table from pages
lib/scatterlist: Add support in dynamic allocation of SG table from pages
tools/testing/scatterlist: Show errors in human readable form
tools/testing/scatterlist: Rejuvenate bit-rotten test
RDMA/ipoib: Set rtnl_link_ops for ipoib interfaces
RDMA/uverbs: Expose the new GID query API to user space
...
|
|
Add new FTE in TX IPsec FT per IPsec state. It has the
same matching criteria as the RX steering rule.
The IPsec FT is created/destroyed when the first/last rule
is added/deleted respectively.
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Boris Pismenny <borisp@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Add new namespace that represents the NIC TX domain.
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Raed Salem <raeds@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Firmware live patch event notifies the driver that the firmware was just
updated using live patch. In such case the driver should not reload or
re-initiate entities, part to updating the firmware version and
re-initiate the firmware tracer which can be updated by live patch with
new strings database to help debugging an issue.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Once the driver gets sync_reset_request from firmware it prepares for the
coming reset and sends acknowledge.
After getting this event the driver expects device reset, either it will
trigger PCI reset on sync_reset_now event or such PCI reset will be
triggered by another PF of the same device. So it moves to reset
requested mode and if it gets PCI reset triggered by the other PF it
detect the reset and reloads.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Rejecting non-native endian BTF overlapped with the addition
of support for it.
The rest were more simple overlapping changes, except the
renesas ravb binding update, which had to follow a file
move as well as a YAML conversion.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case of pci is offline reclaim_pages_cmd() will still try to call
the FW to release FW pages, cmd_exec() in this case will return a silent
success without actually calling the FW.
This is wrong and will cause page leaks, what we should do is to detect
pci offline or command interface un-available before tying to access the
FW and manually release the FW pages in the driver.
In this patch we share the code to check for FW command interface
availability and we call it in sensitive places e.g. reclaim_pages_cmd().
Alternative fix:
1. Remove MLX5_CMD_OP_MANAGE_PAGES form mlx5_internal_err_ret_value,
command success simulation list.
2. Always Release FW pages even if cmd_exec fails in reclaim_pages_cmd().
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Upon command completion timeout, driver simulates a forced command
completion. In a rare case where real interrupt for that command arrives
simultaneously, it might release the command entry while the forced
handler might still access it.
Fix that by adding an entry refcount, to track current amount of allowed
handlers. Command entry to be released only when this refcount is
decremented to zero.
Command refcount is always initialized to one. For callback commands,
command completion handler is the symmetric flow to decrement it. For
non-callback commands, it is wait_func().
Before ringing the doorbell, increment the refcount for the real completion
handler. Once the real completion handler is called, it will decrement it.
For callback commands, once the delayed work is scheduled, increment the
refcount. Upon callback command completion handler, we will try to cancel
the timeout callback. In case of success, we need to decrement the callback
refcount as it will never run.
In addition, gather the entry index free and the entry free into a one
flow for all command types release.
Fixes: e126ba97dba9 ("mlx5: Add driver for Mellanox Connect-IB adapters")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Currently only 256 vports can be supported as only 8 bits are
reserved for them and 8 bits are reserved for vhca_ids in
metadata reg c0. To support more than 256 vports, replace
vhca_id with a unique shorter 4-bit PF number which covers
upto 16 PF's. Use remaining 12 bits for vports ranging 1-4095.
This will continue to generate unique metadata even if
multiple PCI devices have same switch_id.
Signed-off-by: sunils <sunils@nvidia.com>
Reviewed-by: Parav Pandit <parav@nvidia.com>
Reviewed-by: Vu Pham <vuhuong@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Leon Romanovsky says:
====================
This series from Alex extends software steering interface to support
devices with extra capability "sw_owner_2" which will replace existing
"sw_owner".
====================
Based on the mlx5-next branch at
git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
due to dependencies.
* branch 'mlx5_sw_owner_v2:
RDMA/mlx5: Expose TIR and QP ICM address for sw_owner_v2 devices
RDMA/mlx5: Allow DM allocation for sw_owner_v2 enabled devices
RDMA/mlx5: Add sw_owner_v2 bit capability
|
|
Leon Romanovsky says:
====================
IBTA declares speed as 16 bits, but kernel stores it in u8. This series
fixes in-kernel declaration while keeping external interface intact.
====================
Based on the mlx5-next branch at
git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
due to dependencies.
* branch 'mlx5_active_speed':
RDMA: Fix link active_speed size
RDMA/mlx5: Delete duplicated mlx5_ptys_width enum
net/mlx5: Refactor query port speed functions
|
|
Added sw_owner_v2 which will be enabled for future devices,
replacing sw_owner bit.
Signed-off-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
|
|
Combine two same enums to avoid duplication.
Signed-off-by: Aharon Landau <aharonl@mellanox.com>
Reviewed-by: Michael Guralnik <michaelgur@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
|
|
The functions mlx5_query_port_link_width_oper and
mlx5_query_port_ib_proto_oper are always called together, so combine them
to a new function called mlx5_query_port_oper to avoid duplication.
And while the mlx5i_get_port_settings is the same as
mlx5_query_port_oper therefore let's remove it.
According to the IB spec link_width_oper and ib_proto_oper should be u16
and not as written u8, so perform casting as a preparation to cross-RDMA
patch which will fix that type for all drivers in the RDMA subsystem.
Fixes: ada68c31ba9c ("net/mlx5: Introduce a new header file for physical port functions")
Signed-off-by: Aharon Landau <aharonl@mellanox.com>
Reviewed-by: Michael Guralnik <michaelgur@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
|
|
Add CQE compression support for completions of packets that span
multiple strides in a Striding RQ, per the HW capability.
In our memory model, we use small strides (256B as of today) for the
non-linear SKB mode. This feature allows CQE compression to work also
for multiple strides packets. In this case decompressing the mini CQE
array will use stride index provided by HW as part of the mini CQE.
Before this feature, compression was possible only for single-strided
packets, i.e. for packets of size up to 256 bytes when in non-linear
mode, and the index was maintained by SW.
This feature is supported for ConnectX-5 and above.
Feature performance test:
This was whitebox-tested, we reduced the PCI speed from 125Gb/s to
62.5Gb/s to overload pci and manipulated mlx5 driver to drop incoming
packets before building the SKB to achieve low cpu utilization.
Outcome is low cpu utilization and bottleneck on pci only.
Test setup:
Server: Intel(R) Xeon(R) Silver 4108 CPU @ 1.80GHz server, 32 cores
NIC: ConnectX-6 DX.
Sender side generates 300 byte packets at full pci bandwidth.
Receiver side configuration:
Single channel, one cpu processing with one ring allocated. Cpu utilization
is ~20% while pci bandwidth is fully utilized.
For the generated traffic and interface MTU of 4500B (to activate the
non-linear SKB mode), packet rate improvement is about 19% from ~17.6Mpps
to ~21Mpps.
Without this feature, counters show no CQE compression blocks for
this setup, while with the feature, counters show ~20.7Mpps compressed CQEs
in ~500K compression blocks.
Signed-off-by: Ofer Levi <oferle@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Clock struct is part of struct mlx5_core_dev. Code was inconsistent, on
some cases used container_of and on another used clock->mdev.
Align code to use container_of amd remove clock->mdev pointer.
While here, fix reverse xmas tree coding style.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
|
|
When DCT QPs work in RoCE LAG mode:
1. DCT creation is allowed only when it is supported
2. The "port" of a DCT QP is assigned in a round-robin way
Link: https://lore.kernel.org/r/20200818115245.700581-3-leon@kernel.org
Signed-off-by: Mark Zhang <markz@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
|
|
Pull rdma updates from Jason Gunthorpe:
"A quiet cycle after the larger 5.8 effort. Substantially cleanup and
driver work with a few smaller features this time.
- Driver updates for hfi1, rxe, mlx5, hns, qedr, usnic, bnxt_re
- Removal of dead or redundant code across the drivers
- RAW resource tracker dumps to include a device specific data blob
for device objects to aide device debugging
- Further advance the IOCTL interface, remove the ability to turn it
off. Add QUERY_CONTEXT, QUERY_MR, and QUERY_PD commands
- Remove stubs related to devices with no pkey table
- A shared CQ scheme to allow multiple ULPs to share the CQ rings of
a device to give higher performance
- Several more static checker, syzkaller and rare crashers fixed"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (121 commits)
RDMA/mlx5: Fix flow destination setting for RDMA TX flow table
RDMA/rxe: Remove pkey table
RDMA/umem: Add a schedule point in ib_umem_get()
RDMA/hns: Fix the unneeded process when getting a general type of CQE error
RDMA/hns: Fix error during modify qp RTS2RTS
RDMA/hns: Delete unnecessary memset when allocating VF resource
RDMA/hns: Remove redundant parameters in set_rc_wqe()
RDMA/hns: Remove support for HIP08_A
RDMA/hns: Refactor hns_roce_v2_set_hem()
RDMA/hns: Remove redundant hardware opcode definitions
RDMA/netlink: Remove CAP_NET_RAW check when dump a raw QP
RDMA/include: Replace license text with SPDX tags
RDMA/rtrs: remove WQ_MEM_RECLAIM for rtrs_wq
RDMA/rtrs-clt: add an additional random 8 seconds before reconnecting
RDMA/cma: Execute rdma_cm destruction from a handler properly
RDMA/cma: Remove unneeded locking for req paths
RDMA/cma: Using the standard locking pattern when delivering the removal event
RDMA/cma: Simplify DEVICE_REMOVAL for internal_id
RDMA/efa: Add EFA 0xefa1 PCI ID
RDMA/efa: User/kernel compatibility handshake mechanism
...
|
|
Resolved kernel/bpf/btf.c using instructions from merge commit
69138b34a7248d2396ab85c8652e20c0c39beaba
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When setting the PF interface up/down, notify the firmware to update
uplink state via MODIFY_VPORT_STATE, when E-Switch is enabled.
This behavior will prevent sending traffic out on uplink port when PF is
down, such as sending traffic from a VF interface which is still up.
Currently when calling mlx5e_open/close(), the driver only sends PAOS
command to notify the firmware to set the physical port state to
up/down, however, it is not sufficient. When VF is in "auto" state, it
follows the uplink state, which was not updated on mlx5e_open/close()
before this patch.
When switchdev mode is enabled and uplink representor is first enabled,
set the uplink port state value back to its FW default "AUTO".
Fixes: 63bfd399de55 ("net/mlx5e: Send PAOS command on interface up/down")
Signed-off-by: Ron Diskin <rondi@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Per page request event, FW request to allocated or release pages for a
single function. Driver maintains FW pages object per function, so there
is no need to hold one global page data-base. Instead, have a page
data-base per function, which will improve performance release flow in all
cases, especially for "release all pages".
As the range of function IDs is large and not sequential, use xarray to
store a per function ID page data-base, where the function ID is the key.
Upon first allocation of a page to a function ID, create the page
data-base per function. This data-base will be released only at pagealloc
mechanism cleanup.
NIC: ConnectX-4 Lx
CPU: Intel(R) Xeon(R) CPU E5-2650 v2 @ 2.60GHz
Test case: 32 VFs, measure release pages on one VF as part of FLR
Before: 0.021 Sec
After: 0.014 Sec
The improvement depends on amount of VFs and memory utilization
by them. Time measurements above were taken from idle system.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Up to ConnectX-7 UMR is not used when user passes relaxed ordering access
flag. ConnectX-7 supports setting relaxed ordering read/write mkey
attribute by UMR, indicated by new HCA capabilities.
With ConnectX-7 driver uses UMR when user set relaxed ordering access
flag, in contrast to previous silicon models. Specifically it includes
setting relvant flags of mkey context mask in UMR control segment, and
relaxed ordering write and read flags in UMR mkey context segment.
Link: https://lore.kernel.org/r/20200716105248.1423452-4-leon@kernel.org
Signed-off-by: Meir Lichtinger <meirl@mellanox.com>
Reviewed-by: Michael Guralnik <michaelgur@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
|
|
Use generic mlx5 structure defined in mlx5_ifc.h to represent ConnectX
device data structures instead of using structure defined specifically for
mlx5_ib module.
Link: https://lore.kernel.org/r/20200716105248.1423452-3-leon@kernel.org
Signed-off-by: Meir Lichtinger <meirl@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
|
|
Up to ConnectX-7 setting mkey relaxed ordering read/write attributes
by UMR is not supported. ConnectX-7 supports this option, which is
indicated by two new HCA capabilities - relaxed_ordering_write_umr
and relaxed_ordering_read_umr.
Signed-off-by: Meir Lichtinger <meirl@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
|
|
Add FTE actions IPsec ENCRYPT/DECRYPT
Add ipsec_obj_id field in FTE
Add new action field MLX5_ACTION_IN_FIELD_IPSEC_SYNDROME
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Raed Salem <raeds@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
This to set the base for downstream patches to support
the new IPsec implementation of the Connect-X family.
Following modifications made:
- Remove accel layer dependency from MLX5_FPGA_IPSEC.
- Introduce accel_ipsec_ops, each IPsec device will
have to support these ops.
Signed-off-by: Raed Salem <raeds@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Rename mlx5_ifc_device_virtio_emulation_cap_bits to
mlx5_ifc_virtio_emulation_cap_bits to match names produced by the
tools producing these auto generated files.
In addition missing capabilities that will be required by VDPA
implementation.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
VDPA is a new interface that will be added in subsequent patches. It
uses mlx5 core devices and resources. Add an interface type for it.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
mlx5_fill_page_frag_array() is used to populate dma addresses to
resources that require it, such as QPs, RQs etc. When the resource is
used, PA list permissions are ignored. For resources that use MTT list,
the user is required to provide the access rights. Subsequent patches
use resources that require MTT lists, so modify API and implementation
to support that.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
All conflicts seemed rather trivial, with some guidance from
Saeed Mameed on the tc_ct.c one.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Device unit for port buffers size, xoff_threshold and xon_threshold is
cells. Fix a bug in driver where cell unit size was hard-coded to
128 bytes. This hard-coded value is buggy, as it is wrong for some hardware
versions.
Driver to read cell size from SBCAM register and translate bytes to cell
units accordingly.
In order to fix the bug, this patch exposes SBCAM (Shared buffer
capabilities mask) layout and defines.
If SBCAM.cap_cell_size is valid, use it for all bytes to cells
calculations. If not valid, fallback to 128.
Cell size do not change on the fly per device. Instead of issuing SBCAM
access reg command every time such translation is needed, cache it in
mlx5e_dcbx as part of mlx5e_dcbnl_initialize(). Pass dcbx.port_buff_cell_sz
as a param to every function that needs bytes to cells translation.
While fixing the bug, move MLX5E_BUFFER_CELL_SHIFT macro to
en_dcbnl.c, as it is only used by that file.
Fixes: 0696d60853d5 ("net/mlx5e: Receive buffer configuration")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
This patch exposes new link modes using 100Gbps per lane, including 100G,
200G and 400G modes.
Signed-off-by: Meir Lichtinger <meirl@mellanox.com>
Reviewed-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If in the process of creating the underlay QP for an IPoIB interface
the user has set the address and specifically the 1st-3rd bytes
representing the QP number, use the requested QP number when creating
the underlay QP.
For a user to be able to request a QP number on QP creation, the MKEY_BY_NAME
NVCONFIG should be set. As mkey_by_name and qp_by_name are coupled in FW.
This requires driver to query the mkey_by_name max cap during initialization
and set the current cap if it was enabled in FW.
Signed-off-by: Michael Guralnik <michaelgur@mellanox.com>
Reviewed-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
* 'mlx5-next' of git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux:
net/mlx5: kTLS, Improve TLS params layout structures
net/mlx5: Avoid eswitch header inclusion in fs core layer
net/mlx5: Avoid RDMA file inclusion in core driver
net/mlx5: Add support in query QP, CQ and MKEY segments
net/mlx5: Export resource dump interface
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Add explicit WQE segment structures for the TLS static and progress
params.
According to the HW spec, TISN is not part of the progress params context,
take it out of it.
Rename the control segment tisn field as it could hold either a TIS or
a TIR number.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
mlx5 cq.h does not depend on RDMA verbs.
Remove RDMA verbs file inclusion.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Minor overlapping changes in xfrm_device.c, between the double
ESP trailing bug fix setting the XFRM_INIT flag and the changes
in net-next preparing for bonding encryption support.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce new resource dump segments - PRM_QUERY_QP,
PRM_QUERY_CQ and PRM_QUERY_MKEY. These segments contains the resource
dump in PRM query format.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
|
|
Export some of the resource dump API. mlx5_ib driver will use
it in downstream patches.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
|
|
Since none of the functions need to modify the input mac address,
constify them.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Missed steps during ECE handshake left userspace application with less
options for the ECE handshake. Pass ECE options in the additional
transitions.
Fixes: 50aec2c3135e ("RDMA/mlx5: Return ECE data after modify QP")
Link: https://lore.kernel.org/r/20200616104536.2426384-1-leon@kernel.org
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
Pull rdma updates from Jason Gunthorpe:
"A more active cycle than most of the recent past, with a few large,
long discussed works this time.
The RNBD block driver has been posted for nearly two years now, and
flowing through RDMA due to it also introducing a new ULP.
The removal of FMR has been a recurring discussion theme for a long
time.
And the usual smattering of features and bug fixes.
Summary:
- Various small driver bugs fixes in rxe, mlx5, hfi1, and efa
- Continuing driver cleanups in bnxt_re, hns
- Big cleanup of mlx5 QP creation flows
- More consistent use of src port and flow label when LAG is used and
a mlx5 implementation
- Additional set of cleanups for IB CM
- 'RNBD' network block driver and target. This is a network block
RDMA device specific to ionos's cloud environment. It brings strong
multipath and resiliency capabilities.
- Accelerated IPoIB for HFI1
- QP/WQ/SRQ ioctl migration for uverbs, and support for multiple
async fds
- Support for exchanging the new IBTA defiend ECE data during RDMA CM
exchanges
- Removal of the very old and insecure FMR interface from all ULPs
and drivers. FRWR should be preferred for at least a decade now"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (247 commits)
RDMA/cm: Spurious WARNING triggered in cm_destroy_id()
RDMA/mlx5: Return ECE DC support
RDMA/mlx5: Don't rely on FW to set zeros in ECE response
RDMA/mlx5: Return an error if copy_to_user fails
IB/hfi1: Use free_netdev() in hfi1_netdev_free()
RDMA/hns: Uninitialized variable in modify_qp_init_to_rtr()
RDMA/core: Move and rename trace_cm_id_create()
IB/hfi1: Fix hfi1_netdev_rx_init() error handling
RDMA: Remove 'max_map_per_fmr'
RDMA: Remove 'max_fmr'
RDMA/core: Remove FMR device ops
RDMA/rdmavt: Remove FMR memory registration
RDMA/mthca: Remove FMR support for memory registration
RDMA/mlx4: Remove FMR support for memory registration
RDMA/i40iw: Remove FMR leftovers
RDMA/bnxt_re: Remove FMR leftovers
RDMA/mlx5: Remove FMR leftovers
RDMA/core: Remove FMR pool API
RDMA/rds: Remove FMR support for memory registration
RDMA/srp: Remove support for FMR memory registration
...
|
|
The DC QPs are many-to-one QP types that means that first connection will
establish ECE options that coming connections should follow. Due to this
property, the ECE code was removed between first [1] and second [2] ECE
submissions.
This patch returns the dropped code, because ECE is a property of a
connection and like any other connection users are needed to manage this
data. Allow them to set ECE parameter for DC too and avoid need of having
compatibility flag for the DC ECE.
[1]
https://lore.kernel.org/linux-rdma/20200523132243.817936-1-leon@kernel.org/
[2]
https://lore.kernel.org/linux-rdma/20200525174401.71152-1-leon@kernel.org/
Link: https://lore.kernel.org/r/20200602125548.172654-4-leon@kernel.org
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
spi is __be32, fix that.
Fixes sparse warning:
drivers/net/ethernet/mellanox/mlx5/core/accel/ipsec.c:74:64
warning: incorrect type
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Fix sparse warning:
drivers/net/ethernet/mellanox/mlx5/core/cmd.c:1949:15:
warning: memset with byte count of 271720
mlx5_cmd_stats array is too big to be held inline in mlx5_cmd.
Allocate it separately.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
net/mlx5: Add ability to read and write ECE options
net/mlx5: Add support for RDMA TX FT headers modifying
net/mlx5: Move iseg access helper routines close to mlx5_core driver
net/mlx5: Cleanup mlx5_ifc_fte_match_set_misc2_bits
net/mlx5: Add support in forward to namespace
{IB/net}/mlx5: Simplify don't trap code
net/mlx5: Replace zero-length array with flexible-array
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Instead of hand crafted mlx5_qp_context and mlx5_qp_path use common
MLX5_SET() macros.
Link: https://lore.kernel.org/r/20200526115440.205922-7-leon@kernel.org
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Reviewed-by: Mark Zhang <markz@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
From the mlx5-next branch at
git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux
Required for dependencies in following patches
* branch 'mellanox/mlx5-next':
net/mlx5: Add ability to read and write ECE options
net/mlx5: Add support for RDMA TX FT headers modifying
net/mlx5: Move iseg access helper routines close to mlx5_core driver
net/mlx5: Cleanup mlx5_ifc_fte_match_set_misc2_bits
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
The end result of RDMA-CM ECE handshake is ECE options, which is
needed to be used while configuring data QPs. Such options can
come in any QP state, so add in/out fields to set and query
ECE options.
OUT fields:
* create_qp() - default ECE options for that type of QP.
* modify_qp() - enabled ECE options after QP state transition.
IN fields:
* create_qp() - create QP with this ECE option.
* modify_qp() - requested options. For unconnected QPs, the FW
will return an error if ECE is already configured with any options
that not equal to previously set.
Reviewed-by: Mark Zhang <markz@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
|
|
The MSCC bug fix in 'net' had to be slightly adjusted because the
register accesses are done slightly differently in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
