| Age | Commit message (Collapse) | Author |
|---|
|
We currently have a hack to flip the boot cpu and its secondary thread
to logical cpuid 0 and 1. This means the logical - physical mapping will
differ depending on which cpu is boot cpu. This is most apparent on
kexec, where we might kexec on any cpu and therefore change the mapping
from boot to boot.
The patch below does a first pass early on to work out the logical cpuid
of the boot thread. We then fix up some paca structures to match.
Ive also removed the boot_cpuid_phys variable for ppc64, to be
consistent we use get_hard_smp_processor_id(boot_cpuid) everywhere.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
This implements accurate task and cpu time accounting for 64-bit
powerpc kernels. Instead of accounting a whole jiffy of time to a
task on a timer interrupt because that task happened to be running at
the time, we now account time in units of timebase ticks according to
the actual time spent by the task in user mode and kernel mode. We
also count the time spent processing hardware and software interrupts
accurately. This is conditional on CONFIG_VIRT_CPU_ACCOUNTING. If
that is not set, we do tick-based approximate accounting as before.
To get this accurate information, we read either the PURR (processor
utilization of resources register) on POWER5 machines, or the timebase
on other machines on
* each entry to the kernel from usermode
* each exit to usermode
* transitions between process context, hard irq context and soft irq
context in kernel mode
* context switches.
On POWER5 systems with shared-processor logical partitioning we also
read both the PURR and the timebase at each timer interrupt and
context switch in order to determine how much time has been taken by
the hypervisor to run other partitions ("steal" time). Unfortunately,
since we need values of the PURR on both threads at the same time to
accurately calculate the steal time, and since we can only calculate
steal time on a per-core basis, the apportioning of the steal time
between idle time (time which we ceded to the hypervisor in the idle
loop) and actual stolen time is somewhat approximate at the moment.
This is all based quite heavily on what s390 does, and it uses the
generic interfaces that were added by the s390 developers,
i.e. account_system_time(), account_user_time(), etc.
This patch doesn't add any new interfaces between the kernel and
userspace, and doesn't change the units in which time is reported to
userspace by things such as /proc/stat, /proc/<pid>/stat, getrusage(),
times(), etc. Internally the various task and cpu times are stored in
timebase units, but they are converted to USER_HZ units (1/100th of a
second) when reported to userspace. Some precision is therefore lost
but there should not be any accumulating error, since the internal
accumulation is at full precision.
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
This patch removes all self references and fixes references to files
in the now defunct arch/ppc64 tree. I think this accomplises
everything wanted, though there might be a few references I missed.
Signed-off-by: Jon Mason <jdmason@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
At present the lppaca - the structure shared with the iSeries
hypervisor and phyp - is contained within the PACA, our own low-level
per-cpu structure. This doesn't have to be so, the patch below
removes it, making a separate array of lppaca structures.
This saves approximately 500*NR_CPUS bytes of image size and kernel
memory, because we don't need aligning gap between the Linux and
hypervisor portions of every PACA. On the other hand it means an
extra level of dereference in many accesses to the lppaca.
The patch also gets rid of several places where we assign the paca
address to a local variable for no particular reason.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
The current ppc64 per cpu data implementation is quite slow. eg:
lhz 11,18(13) /* smp_processor_id() */
ld 9,.LC63-.LCTOC1(30) /* per_cpu__variable_name */
ld 8,.LC61-.LCTOC1(30) /* __per_cpu_offset */
sldi 11,11,3 /* form index into __per_cpu_offset */
mr 10,9
ldx 9,11,8 /* __per_cpu_offset[smp_processor_id()] */
ldx 0,10,9 /* load per cpu data */
5 loads for something that is supposed to be fast, pretty awful. One
reason for the large number of loads is that we have to synthesize 2
64bit constants (per_cpu__variable_name and __per_cpu_offset).
By putting __per_cpu_offset into the paca we can avoid the 2 loads
associated with it:
ld 11,56(13) /* paca->data_offset */
ld 9,.LC59-.LCTOC1(30) /* per_cpu__variable_name */
ldx 0,9,11 /* load per cpu data
Longer term we can should be able to do even better than 3 loads.
If per_cpu__variable_name wasnt a 64bit constant and paca->data_offset
was in a register we could cut it down to one load. A suggestion from
Rusty is to use gcc's __thread extension here. In order to do this we
would need to free up r13 (the __thread register and where the paca
currently is). So far Ive had a few unsuccessful attempts at doing that :)
The patch also allocates per cpu memory node local on NUMA machines.
This patch from Rusty has been sitting in my queue _forever_ but stalled
when I hit the compiler bug. Sorry about that.
Finally I also only allocate per cpu data for possible cpus, which comes
straight out of the x86-64 port. On a pseries kernel (with NR_CPUS == 128)
and 4 possible cpus we see some nice gains:
total used free shared buffers cached
Mem: 4012228 212860 3799368 0 0 162424
total used free shared buffers cached
Mem: 4016200 212984 3803216 0 0 162424
A saving of 3.75MB. Quite nice for smaller machines. Note: we now have
to be careful of per cpu users that touch data for !possible cpus.
At this stage it might be worth making the NUMA and possible cpu
optimisations generic, but per cpu init is done so early we have to be
careful that all architectures have their possible map setup correctly.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
include/asm-ppc/ had #ifdef __KERNEL__ in all header files that
are not meant for use by user space, include/asm-powerpc does
not have this yet.
This patch gets us a lot closer there. There are a few cases
where I was not sure, so I left them out. I have verified
that no CONFIG_* symbols are used outside of __KERNEL__
any more and that there are no obvious compile errors when
including any of the headers in user space libraries.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
This patch removes several unnecessary fields from the paca:
- next_jiffy_update_tb was simply unused. Remove trivially.
- The exdsi exception save area was not used. There were plans to use
it, but they never seem to have gone anywhere. If they ever do, we
can put it back. Remove from the paca, and from asm-offsets.c
- The default_decr field was used from asm, but was only ever assigned
the value of tb_ticks_per_jiffy. Just access tb_ticks_per_jiffy from
asm directly instead.
Built and booted on POWER5 LPAR and iSeries RS64.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
On iSeries, the paca contains, amongst other things an ItLpRegSave
structure used by the hypervisor to save registers. The hypervisor
locates this area through a pointer at the beginning of the paca, so
the structure itself can be located elsewhere. This patch moves the
reg_save area out into its own array. This reduces the amount of
iSeries specific gunk which is visible to general powerpc code via
paca.h
Built and booted on POWER5 LPAR and iSeries RS64.
Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
This patch moves a bunch of files from arch/ppc64 and
include/asm-ppc64 which have no equivalents in ppc32 code into
arch/powerpc and include/asm-powerpc. The file affected are:
abs_addr.h
compat.h
lppaca.h
paca.h
tce.h
cpu_setup_power4.S
ioctl32.c
firmware.c
pacaData.c
The only changes apart from the move and corresponding Makefile
changes are:
- #ifndef/#define in includes updated to _ASM_POWERPC_ form
- trailing whitespace removed
- comments giving full paths removed
- pacaData.c renamed paca.c to remove studlyCaps
- Misplaced { moved in lppaca.h
Built and booted on POWER5 LPAR (ARCH=powerpc and ARCH=ppc64), built
for 32-bit powermac (ARCH=powerpc).
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
