Age | Commit message (Collapse) | Author |
|
sd_ioctl() still use printk() for log output.
It should use sd_printk() instead of printk(), as well as other sd_*.
All SCSI messages should output via s*_printk() instead of printk().
Signed-off-by: Nao Nishijima <nao.nishijima.xt@hitachi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Since it is already called in the right context with rtnl_lock and dev_mutex
held.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Fix SYSFS interface issues.
- In the lpfc_sli4_pdev_status_reg_wait() routine, after initial 100ms delay
following write to PHYSDEV_CONTROL register for the firmware reaction, check
the RN bit and ERR bit of the SLIPORT_STATUS register. If none of them
became 1, the previous PHYSDEV_CONTROL register should be considered failed
due to lack of privilege and error for no permission should be returned
immediately without getting into the wait for RDY bits on the SLIPORT_STATUS
register.
- Remove the driver check on dev->is_physfn before proceed to perform the
PHYSDEV_CONTROL register write, and let the PCI function's privilege
setting and driver handling of PHYSDEV_CONTROL register write failure to
handle the reset-ability through the SLI port.
- Added key to ctlreg_write to prevent unauthorized or unexpected write to
the control register.
- Change return to EACCES for sysfs access that are failed because hba_reset
is disabled.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Fix HBA initialization issues
- Swap all values that come from the firmware image on little endian systems.
Created a new bf_get_be macro that does the same as the bf_get_le macro but
for big endian data instead of little endian data.
- Moved the incrementing of temp_offset after the copy
fixed the write object loop to use temp_offset to figure out where the end
of the image is instead of offset.
- Added the necessary codes for properly bringing the driver instance offline
and then trying to bring the port back online with the PCI function IP reset.
If it fails to bring the SLI port back online, it will fall through to
bringing the SLI port to HBA error offline.
- Add a call in the probe_one_s3 and probe_one_s4 routines to get the Modeldesc
- Change OCe50100 to OCe15100
- Made the error log also include the PCI BAR bitmap returned from kernel call
pci_select_bars().
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Fix issues pertaining to SCSI/FC protocol.
- Allow frames destined to 0xFFFFFE to be processed by the driver by matching
that DID with the physical port.
- Call lpfc_sli_issue_iocb with context1 set to ndlp
- In echo command accept function, adjust memcpy to limit memcpy to 1K
- Set LPFC_SLI3_BG_ENABLED properly upon completion.
- Skip the INIT_VFI call in lpfc_register_fcf if the FCF is already
registered and go immediately to initial flogi.
- use "status" variable instead of "ret" variable to hold the return of the
fc_block_scsi_eh.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
This patch adds call to pci_disable_device during
rmmod and shutdown. The lack of this call was causing hang in
insmod - rmmod loop test
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
This patch adds a shutdown routine. It fixes a bug where when be2net
and be2iscsi are both used be2iscsi was not cleaning up its resources
properly causing be2net to fail to get loaded when the system is
rebooted.
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Fix be2iscsi driver to use a separate pointer for each irq action->name
field and avoid display corruption in /proc/interrupts. The be2iscsi driver
was using a single static array in a function for the irq action->name field.
This results in garbage output from /proc/interrupts
The pointer for action->name is garbage and scribbles the output on the screen.
This patch fixes the problem:
156: 0 0 0 0 0 0
0 0 0 0 0 0 0
0 0 0 0 0 0 0
0 0 0 0 PCI-MSI-X beiscsi_msix_0017
This patch is based on Prarit's patch here:
http://www.spinics.net/lists/linux-scsi/msg52325.html
but I have fixed up the failure paths and removed
redundant check for !i suggested by Eike.
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Since active_mask is first assigned in an "else" block, the compiler throws
a warning saying that the active_mask variable may be used uninitialized in
a print statement later. Initialize active_mask to 0 in the declaration to
stop the warning.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
for ISP82xx.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Return sysfs error codes that match the conditions encountered.
This prevents sysfs from retrying a request which is conditioned
to fail under the current circumstance.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Provide bsg interface for updating VPD attached on the I2C serial bus.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Corrects the return value for the cases where read/write edc fails;
this prevents sysfs from retrying the operation until forever.
Corrects the printk width specifier for the first byte of buf.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
parameters to be changed dynamically.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Driver is not releasing the lock if ql2xdontresethba is set, this might lead
to a lockup.
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
[jejb: fix up checkpatch.pl errors]
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Minidump allows us to catpure a snapshot of the firmware/hardware states at the
time of failure for further analysis.
[jejb: added missing #include <linux/vmalloc.h>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au> ]
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
FICON Express8S supports hardware data router, which requires an
adapted qdio request format.
This part 2/2 exploits the functionality in zfcp.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
FICON Express8S supports hardware data router, which requires an
adapted qdio request format.
This part 1/2 provides the qdio base required for exploitation in
zfcp.
Signed-off-by: Swen Schillig <swen@vnet.ibm.com>
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
DIF/DIX support for zfcp is no longer experimental,
and config option is no longer necessary.
Return error from queuecommand for unsupported data directions.
Signed-off-by: Steffen Maier <maier@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
The Marvell Universal Message Interface (UMI) defines a messaging
interface between host and Marvell products (Plato, for example). It
considers situations of limited system resource and optimized system
performance.
UMI driver translates host request to message and sends message
to FW via UMI, FW receives message and processes it, then sends response
to UMI driver.
FW generates an interrupt when it needs to send information or
response to UMI driver
Signed-off-by: Jianyun Li <jyli@marvell.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Export the name of iface session is attached to. This is needed
so tools like iscsiadm/iscsistart can match the sessions to
userspace ifaces when rebuilding iscsid's state during boot.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Added new sysfs attr 'host_reset' in scsi_sysfs.c to
perform adapter or firmware reset as suggested by
Mike Christie here:
http://marc.info/?l=linux-scsi&m=127359347111167&w=2
user/application can write "adapter" or "firmware" on
this attr and it will call newly added function hook
in scsi_host_template to call LDD adapter or firmware
reset implementation.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
This command is used to read ACB params from firmware
Signed-off-by: Harish Zunjarrao <harish.zunjarrao@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
This command will causes the firmware to update all
configurations to pre-defined factory default settings.
Signed-off-by: Harish Zunjarrao <harish.zunjarrao@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Some CD-ROMs fail to report a media change correctly. The specific
one for this patch simply fails to respond to commands, then gives a
UNIT ATTENTION after being reset which returns ASC/ASCQ 28/00. This
is out of spec behaviour, but add a check in the eat CC/UA on reset
path to catch this case so the CD-ROM will function somewhat properly.
[jejb: fixed up white space and accepted without signoff]
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Added board_id, fw_state, phy_port_cnt, phy_port_num,
iscsi_func_cnt, hba_model
Signed-off-by: Harish Zunjarrao <harish.zunjarrao@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Signed-off-by: Harish Zunjarrao <harish.zunjarrao@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Signed-off-by: Harish Zunjarrao <harish.zunjarrao@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
- Corrected return status
- Added reset active check
- Removed unused dma_map_sg calls
- Added debug prints on failure
Signed-off-by: Harish Zunjarrao <harish.zunjarrao@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Hook qla4xxx in fw boot sysfs interface so iscsi tools
can use the info to create boot sessions.
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
1. Remove device database entry (ddb) state.
2. Remove device database (DDB) list building.
With open-iscsi integration the logins to the target devices are
handled by the user space. So the information of target is now
maintained in the iscsi_session object. This is handled at
libiscsi level so there is no need to maintain a list of DDBs in
the qla4xxx LLD.
3. qla4xxx: Remove add_device_dynamically.
Since autologin in FW is disabled with open-iscsi integration,
driver will never get an AEN for which driver has not requested
a DDB index. So remove the add_device_dynamically function.
4. Remove qla4xxx_tgt_dscvr
Since firmware autologin is disabled this function will not work.
Now user has the ability to do the target discovery and login to
each target individually. Firwmare will not do the login on its own.
5. Remove relogin related code
All relogin is handled by userspace now. qla4xxx just need to
notify userspace of a connection failure, this triggers the
relogin.
6. Remove add_session and alloc_session
Now qla4xxx uses iscsi_session_setup that would do the necessary
allocations for session and ddb_entry.
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Add scsi_transport_iscsi hooks in qla4xxx to support
iSCSI session management using iscsiadm.
This patch is based on discussion here
http://groups.google.com/group/open-iscsi/browse_thread/thread/e89fd888baf656a0#
Now users can use iscsiadm to do target discovery and do login/logout to
individual targets using the qla4xxx iSCSI class interface.
This patch leaves some dead code, but to make it easier to review
we are leaving and in the next patch we will remove that old code.
V2 - NOTE: Added code to avoid waiting for AEN during login/logout
in the driver, instead added a kernel to user event
to notify iscsid about login status. Because of this
iscsid will not get blocked.
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
support offload session login.
Offload drivers like qla4xxx will offload the sending of the login/logout
pdus still, so this patch adds iscsi_conn_login_event which is
used by these types of drivers to notify userspace that the connection
has changed state.
It also adds a iscsi_is_session_online helper so the lld
can query the sessions state field.
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
This patch adds bsg support to qla4xxx.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Harish Zunjarrao <harish.zunjarrao@qlogic.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
This patch adds bsg support to the iscsi class. There is only
1 request, the host vendor one, supported. It is expected that
this would be used for things like flash updates.
This patch is made over this one
http://marc.info/?l=linux-scsi&m=131149780020992&w=2
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Add support to set VLAN and show vlan settings in sysfs
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: Harish Zunjarrao <harish.zunjarrao@qlogic.com>
[Patch updated to new defines]
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
libiscsi does not support markers and if someone tries
to set them the driver does a BUG(). There is not need
to be that extreme. Just return -ENOSYS.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Add support to set vlan priority and enable/disble a vlan.
Patch based on code from Vikas Chaudhary.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
iscsi_session_to_shost is a macro around dev_to_shost which returns a
Scsi_Host so there is no need to cast.
iscsi_session_to_shost is a macro around shost_priv which
returns a void pointer so no need to cast.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
The iscsi class currently does not support writable sysfs
attrs for LLD sysfs settings. This patch converts the
iscsi class and driver's host attrs to use the attribute
container sysfs group and the sysfs group's is_visible callout
to be able to support readable or writable sysfs attrs.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|