| Age | Commit message (Collapse) | Author |
|---|
|
commit d79f16c046086f4fe0d42184a458e187464eb83e fixed a user triggerable
scribble on free memory but added a new one which allows the user to
scribble even more and user controlled data into freed space.
As with 6pack we need to halt the queue before we free the buffers, because
the transmit logic is not protected by the semaphore.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit acf673a3187edf72068ee2f92f4dc47d66baed47 fixed a user triggerable free
memory scribble but in doing so replaced it with a different one that allows
the user to control the data and scribble even more.
sixpack_close is called by the tty layer in tty context. The tty context is
protected by sp_get() and sp_put(). However network layer activity via
sp_xmit() is not protected this way. We must therefore stop the queue
otherwise the user gets to dump a buffer mostly of their choice into freed
kernel pages.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commands run in a vrf context are not failing as expected on a route lookup:
root@kenny:~# ip ro ls table vrf-red
unreachable default
root@kenny:~# ping -I vrf-red -c1 -w1 10.100.1.254
ping: Warning: source address might be selected on device other than vrf-red.
PING 10.100.1.254 (10.100.1.254) from 0.0.0.0 vrf-red: 56(84) bytes of data.
--- 10.100.1.254 ping statistics ---
2 packets transmitted, 0 received, 100% packet loss, time 999ms
Since the vrf table does not have a route for 10.100.1.254 the ping
should have failed. The saddr lookup causes a full VRF table lookup.
Propogating a lookup failure to the user allows the command to fail as
expected:
root@kenny:~# ping -I vrf-red -c1 -w1 10.100.1.254
connect: No route to host
Signed-off-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the reset_resume() is called, the flag of SELECTIVE_SUSPEND should be
cleared and reinitialize the device, whether the SELECTIVE_SUSPEND is set
or not. If reset_resume() is called, it means the power supply is cut or the
device is reset. That is, the device wouldn't be in runtime suspend state and
the reinitialization is necessary.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Dmitry reports memleak with syskaller program.
Problem is that connector bumps skb usecount but might not invoke callback.
So move skb_get to where we invoke the callback.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since t4_alloc_mem can be failed in memory pressure,
if not properly handled, NULL dereference could be happened.
Signed-off-by: Insu Yun <wuninsu@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since qlcnic_alloc_mbx_args can be failed,
return value should be checked.
Signed-off-by: Insu Yun <wuninsu@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI bugfix from Bjorn Helgaas:
"Here's another fix for v4.4.
This fixes 32-bit config reads for the HiSilicon driver. Obviously
the driver is completely broken without this fix (apparently it
actually was tested internally, but got broken somehow in the process
of upstreaming it).
Summary:
HiSilicon host bridge driver
Fix 32-bit config reads (Dongdong Liu)"
* tag 'pci-v4.4-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: hisi: Fix hisi_pcie_cfg_read() 32-bit reads
|
|
Pull networking fixes from David Miller:
1) Prevent XFRM per-cpu counter updates for one namespace from being
applied to another namespace. Fix from DanS treetman.
2) Fix RCU de-reference in iwl_mvm_get_key_sta_id(), from Johannes
Berg.
3) Remove ethernet header assumption in nft_do_chain_netdev(), from
Pablo Neira Ayuso.
4) Fix cpsw PHY ident with multiple slaves and fixed-phy, from Pascal
Speck.
5) Fix use after free in sixpack_close and mkiss_close.
6) Fix VXLAN fw assertion on bnx2x, from Yuval Mintz.
7) natsemi doesn't check for DMA mapping errors, from Alexey
Khoroshilov.
8) Fix inverted test in ip6addrlbl_get(), from ANdrey Ryabinin.
9) Missing initialization of needed_headroom in geneve tunnel driver,
from Paolo Abeni.
10) Fix conntrack template leak in openvswitch, from Joe Stringer.
11) Mission initialization of wq->flags in sock_alloc_inode(), from
Nicolai Stange.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (35 commits)
sctp: sctp should release assoc when sctp_make_abort_user return NULL in sctp_close
net, socket, socket_wq: fix missing initialization of flags
drivers: net: cpsw: fix error return code
openvswitch: Fix template leak in error cases.
sctp: label accepted/peeled off sockets
sctp: use GFP_USER for user-controlled kmalloc
qlcnic: fix a loop exit condition better
net: cdc_ncm: avoid changing RX/TX buffers on MTU changes
geneve: initialize needed_headroom
ipv6: honor ifindex in case we receive ll addresses in router advertisements
addrconf: always initialize sysctl table data
ipv6/addrlabel: fix ip6addrlbl_get()
switchdev: bridge: Pass ageing time as clock_t instead of jiffies
sh_eth: fix 16-bit descriptor field access endianness too
veth: don’t modify ip_summed; doing so treats packets with bad checksums as good.
net: usb: cdc_ncm: Adding Dell DW5813 LTE AT&T Mobile Broadband Card
net: usb: cdc_ncm: Adding Dell DW5812 LTE Verizon Mobile Broadband Card
natsemi: add checks for dma mapping errors
rhashtable: Kill harmless RCU warning in rhashtable_walk_init
openvswitch: correct encoding of set tunnel action attributes
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
iwlwifi
* don't load firmware that won't exist for 7260
* fix RCU splat
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull block fixes from Jens Axboe:
"Make the block layer great again.
Basically three amazing fixes in this pull request, split into 4
patches. Believe me, they should go into 4.4. Two of them fix a
regression, the third and last fixes an easy-to-trigger bug.
- Fix a bad irq enable through null_blk, for queue_mode=1 and using
timer completions. Add a block helper to restart a queue
asynchronously, and use that from null_blk. From me.
- Fix a performance issue in NVMe. Some devices (Intel Pxxxx) expose
a stripe boundary, and performance suffers if we cross it. We took
that into account for merging, but not for the newer splitting
code. Fix from Keith.
- Fix a kernel oops in lightnvm with multiple channels. From Matias"
* 'for-linus' of git://git.kernel.dk/linux-block:
lightnvm: wrong offset in bad blk lun calculation
null_blk: use async queue restart helper
block: add blk_start_queue_async()
block: Split bios on chunk boundaries
|
|
Propagate the return value of platform_get_irq on failure.
A simplified version of the semantic match that finds the two cases where
no error code is returned at all is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret; expression e1,e2;
@@
(
if (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
dev->nr_luns reports the total number of luns available in a device
while dev->luns_per_chnl is the number of luns per channel.
When multiple channels are available, the offset is calculated from a
channel and lun id into a linear array. As it multiplies with
the total number of luns, we go out of bound when channel id > 0 and
causes the kernel to panic when we read a protected kernel memory area.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma fixes from Doug Ledford:
"Three late 4.4-rc fixes.
The first two were very small in terms of number of lines, the third
is more lines of change than I like this late in the cycle, but there
are positive test results from Avagotech and from my own test setup
with the target hardware, and given the problem was a 100% failure
case, I sent it through.
- A previous patch updated the mlx4 driver to use vmalloc when there
was not enough memory to get a contiguous region large enough for
our needs, so we need kvfree() whenever we free that item. We
missed one place, so fix that now.
- A previous patch added code to match incoming packets against a
specific device, but failed to compensate for devices that have
both InfiniBand and Ethernet ports. Fix that.
- Under certain vlan conditions, the ocrdma driver would fail to
bring up any vlan interfaces and would print out a circular locking
failure. Fix that"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma:
RDMA/be2net: Remove open and close entry points
RDMA/ocrdma: Depend on async link events from CNA
RDMA/ocrdma: Dispatch only port event when port state changes
RDMA/ocrdma: Fix vlan-id assignment in qp parameters
IB/mlx4: Replace kfree with kvfree in mlx4_ib_destroy_srq
IB/cma: cma_match_net_dev needs to take into account port_num
|
|
If null_blk is run in NULL_IRQ_TIMER mode and with queue_mode NULL_Q_RQ,
we need to restart the queue from the hrtimer interrupt. We can't
directly invoke the request_fn from that context, so punt the queue run
to async kblockd context.
Tested-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Recently Dough Ledford reported a deadlock happening
between ocrdma-load sequence and NetworkManager service
issueing "open" on be2net interface.
The deadlock happens when any be2net hook (e.g. open/close) is called
in parallel to insmod ocrdma.ko.
A. be2net is sending administrative open/close event to ocrdma holding
device_list_mutex. It does this from ndo_open/ndo_stop hooks of be2net.
So sequence of locks is rtnl_lock---> device_list lock
B. When new ocrdma roce device gets registered, infiniband stack now
takes rtnl_lock in ib_register_device() in GID initialization routines.
So sequence of locks in this path is device_list lock ---> rtnl_lock.
This improper locking sequence causes deadlock.
In order to resolve the above deadlock condition, ocrdma intorduced a
patch to stop listening to administrative open/close events generated from
be2net driver. It now depends on link-state-change async-event generated from
CNA. This change leaves behind dead code which used to generate administrative
open/close events. This patch cleans-up all that dead code from be2net.
Reported-by: Doug Ledford <dledford@redhat.com>
CC: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@avagotech.com>
Signed-off-by: Selvin Xavier <selvin.xavier@avagotech.com>
Signed-off-by: Devesh Sharma <devesh.sharma@avagotech.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Recently Dough Ledford reported a deadlock happening
between ocrdma-load sequence and NetworkManager service
issuing "open" on be2net interface.
The deadlock happens when any be2net hook (e.g. open/close) is called
in parallel to insmod ocrdma.ko.
A. be2net is sending administrative open/close event to ocrdma holding
device_list_mutex. It does this from ndo_open/ndo_stop hooks of be2net.
So sequence of locks is rtnl_lock---> device_list lock
B. When new ocrdma roce device gets registered, infiniband stack now
takes rtnl_lock in ib_register_device() in GID initialization routines.
So sequence of locks in this path is device_list lock ---> rtnl_lock.
This improper locking sequence causes deadlock.
With this patch we stop using administrative open and close events
injected by be2net driver. These events were used to dispatch PORT_ACTIVE
and PORT_ERROR events to the IB-stack. This patch implements a logic
to receive async-link-events generated from CNA whenever link-state-change
is detected. Now on, these async-events will be used to dispatch
PORT_ACTIVE and PORT_ERROR events to IB-stack.
Depending on async-events from CNA removes the need to hold device-list-mutex
and thus breaks the busy-wait scenario.
Reported-by: Doug Ledford <dledford@redhat.com>
CC: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@avagotech.com>
Signed-off-by: Selvin Xavier <selvin.xavier@avagotech.com>
Signed-off-by: Devesh Sharma <devesh.sharma@avagotech.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Dispatch only port event to IB stack when port state changes.
Don't explicitly modify qps to error. Let application listen to
port events on async event queue or let QP fail with retry-exceeded
completion error.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@avagotech.com>
Signed-off-by: Devesh Sharma <devesh.sharma@avagotech.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
vlan-id is wrongly getting as 0 when PFC is enabled.
Set vlan-id configured by user in QP parameters.
In case vlan interface is not used, flash a warning to
user to configure vlan and assign vlan-id as 0 in qp params.
Fixes: dbf727de7440 ('IB/core: Use GID table in AH creation and dmac resolution')
Cc: Matan Barak <matanb@mellanox.com>
Signed-off-by: Devesh Sharma <devesh.sharma@avagotech.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A smallish set of fixes that we've been sitting on for a while now,
flushing the queue here so they go in. Summary:
A handful of fixes for OMAP, i.MX, Allwinner and Tegra:
- A clock rate and a PHY setup fix for i.MX6Q/DL
- A couple of fixes for the reduced serial bus (sunxi-rsb) on
Allwinner
- UART wakeirq fix for an OMAP4 board, timer config fixes for AM43XX.
- Suspend fix for Tegra124 Chromebooks
- Fix for missing implicit include that's different between
ARM/ARM64"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: tegra: Fix suspend hang on Tegra124 Chromebooks
bus: sunxi-rsb: Fix peripheral IC mapping runtime address
bus: sunxi-rsb: Fix primary PMIC mapping hardware address
ARM: dts: Fix UART wakeirq for omap4 duovero parlor
ARM: OMAP2+: AM43xx: select ARM TWD timer
ARM: OMAP2+: am43xx: enable GENERIC_CLOCKEVENTS_BROADCAST
fsl-ifc: add missing include on ARM64
ARM: dts: imx6: Fix Ethernet PHY mode on Ventana boards
ARM: dts: imx: Fix the assigned-clock mismatch issue on imx6q/dl
bus: sunxi-rsb: unlock on error in sunxi_rsb_read()
ARM: dts: sunxi: sun6i-a31s-primo81.dts: add touchscreen axis swapping property
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael Wysocki:
"These fix an ACPI processor driver regression introduced during the
4.3 cycle and a mistake in the recently added SCPI support in the
arm_big_little cpufreq driver.
Specifics:
- Fix a thermal management issue introduced by an ACPI processor
driver change made during the 4.3 development cycle that failed to
return 0 from a function on success which triggered an error
cleanup path every time it had been called that deleted useful data
structures created previously (Srinivas Pandruvada).
- Fix a variable data type issue in the arm_big_little cpufreq
driver's SCPI support code added recently that prevents error
handling in there from working correctly (Dan Carpenter)"
* tag 'pm+acpi-4.4-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: scpi-cpufreq: signedness bug in scpi_get_dvfs_info()
ACPI / processor: Fix thermal cooling device regression
|
|
Pull md bugfix from Neil Brown:
"One more md fix for 4.4-rc
Fix a regression which causes reshape to not start properly sometimes"
* tag 'md/4.4-rc6-fix' of git://neil.brown.name/md:
md: remove check for MD_RECOVERY_NEEDED in action_store.
|
|
Pull UBI bug fixes from Richard Weinberger:
"This contains four bug fixes for UBI"
* tag 'upstream-4.4-rc7' of git://git.infradead.org/linux-ubifs:
mtd: ubi: don't leak e if schedule_erase() fails
mtd: ubi: fixup error correction in do_sync_erase()
UBI: fix use of "VID" vs. "EC" in header self-check
UBI: fix return error code
|
|
* acpi-processor:
ACPI / processor: Fix thermal cooling device regression
* pm-cpufreq:
cpufreq: scpi-cpufreq: signedness bug in scpi_get_dvfs_info()
|
|
Pull sparc fixes from David Miller:
1) Finally make perf stack backtraces stable on sparc, several problems
(mostly due to the context in which the user copies from the stack
are done) contributed to this.
From Rob Gardner.
2) Export ADI capability if the cpu supports it.
3) Hook up userfaultfd system call.
4) When faults happen during user copies we really have to clean up and
restore the FPU state fully. Also from Rob Gardner
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
tty/serial: Skip 'NULL' char after console break when sysrq enabled
sparc64: fix FP corruption in user copy functions
sparc64: Perf should save/restore fault info
sparc64: Ensure perf can access user stacks
sparc64: Don't set %pil in rtrap_nmi too early
sparc64: Add ADI capability to cpu capabilities
tty: serial: constify sunhv_ops structs
sparc: Hook up userfaultfd system call
|
|
When sysrq is triggered from console, serial driver for SUN hypervisor
console receives a console break and enables the sysrq. It expects a valid
sysrq char following with break. Meanwhile if driver receives 'NULL'
ASCII char then it disables sysrq and sysrq handler will never be invoked.
This fix skips calling uart sysrq handler when 'NULL' is received while
sysrq is enabled.
Signed-off-by: Vijay Kumar <vijay.ac.kumar@oracle.com>
Acked-by: Karl Volz <karl.volz@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Constifies sunhv_ops structures in tty's serial
driver since they are not modified after their
initialization.
Detected and found using Coccinelle.
Suggested-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Aya Mahfouz <mahfouz.saif.elyazal@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the original code, if we succeeded on the last iteration through the
loop then we still returned failure.
Fixes: 389e4e04ad2d ('qlcnic: fix a timeout loop')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
NCM buffer sizes are negotiated with the device independently of
the network device MTU. The RX buffers are allocated by the
usbnet framework based on the rx_urb_size value set by cdc_ncm. A
single RX buffer can hold a number of MTU sized packets.
The default usbnet change_mtu ndo only modifies rx_urb_size if it
is equal to hard_mtu. And the cdc_ncm driver will set rx_urb_size
and hard_mtu independently of each other, based on dwNtbInMaxSize
and dwNtbOutMaxSize respectively. It was therefore assumed that
usbnet_change_mtu() would never touch rx_urb_size. This failed to
consider the case where dwNtbInMaxSize and dwNtbOutMaxSize happens
to be equal.
Fix by implementing an NCM specific change_mtu ndo, modifying the
netdev MTU without touching the buffer size settings.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently the needed_headroom field for the geneve device is left
to the default value.
This patch set it to space required for basic geneve encapsulation,
so that we can avoid the skb head re-allocation on xmit.
This give a 6% speedup for unsegment traffic on geneve tunnel.
v1 -> v2:
- add ETH_HLEN for the lower device to the needed headroom
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The "domain" variable needs to be signed for the error handling to work.
Fixes: 8def31034d03 (cpufreq: arm_big_little: add SCPI interface driver)
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://anongit.freedesktop.org/drm-intel
Pull i915 drm fixes from Jani Nikula:
"Here's a batch of i915 fixes all around. It may be slightly bigger
than one would hope for at this stage, but they've all been through
testing in our -next before being picked up for v4.4. Also, I missed
Dave's fixes pull earlier today just because I wanted an extra testing
round on this. So I'm fairly confident.
Wishing you all the things it is customary to wish this time of the
year"
* tag 'drm-intel-fixes-2015-12-23' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Correct max delay for HDMI hotplug live status checking
drm/i915: mdelay(10) considered harmful
drm/i915: Kill intel_crtc->cursor_bo
drm/i915: Workaround CHV pipe C cursor fail
drm/i915: Only spin whilst waiting on the current request
drm/i915: Limit the busy wait on requests to 5us not 10ms!
drm/i915: Break busywaiting for requests on pending signals
drm/i915: Disable primary plane if we fail to reconstruct BIOS fb (v2)
drm/i915: Set the map-and-fenceable flag for preallocated objects
drm/i915: Drop the broken cursor base==0 special casing
|
|
Pull drm fixes from Dave Airlie:
"Not much happening, should have dequeued this lot earlier.
One amdgpu, one nouveau and one exynos fix"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/exynos: atomic check only enabled crtc states
drm/nouveau/bios/fan: hardcode the fan mode to linear
drm/amdgpu: fix user fence handling
|
|
Commit 0ef2f05c7e02ff99c0b5b583d7dee2cd12b053f2 uses vmalloc for WR buffers
when needed and uses kvfree to free the buffers. It missed changing kfree
to kvfree in mlx4_ib_destroy_srq().
Reported-by: Matthew Finaly <matt@Mellanox.com>
Signed-off-by: Wengang Wang <wen.gang.wang@oracle.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Previously, cma_match_net_dev called cma_protocol_roce which
tried to verify that the IB device uses RoCE protocol. However,
if rdma_id wasn't bound to a port, then the check would occur
against the first port of the device without regard to whether
that port was even of the same type as the type of port the
incoming packet was received on.
Fix this by passing the port of the request and only checking
against the same port of the device.
Reported-by: Or Gerlitz <gerlitz.or@gmail.com>
Fixes: b8cab5dab15f ('IB/cma: Accept connection without a valid netdev on RoCE')
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Pull block layer fixes from Jens Axboe:
"Three small fixes for 4.4 final. Specifically:
- The segment issue fix from Junichi, where the old IO path does a
bio limit split before potentially bouncing the pages. We need to
do that in the right order, to ensure that limitations are met.
- A NVMe surprise removal IO hang fix from Keith.
- A use-after-free in null_blk, introduced by a previous patch in
this series. From Mike Krinkin"
* 'for-linus' of git://git.kernel.dk/linux-block:
null_blk: fix use-after-free error
block: ensure to split after potentially bouncing a bio
NVMe: IO ending fixes on surprise removal
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Martin Schwidefsky:
"Two late bug fixes for kernel 4.4.
Merry Christmas"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/dis: Fix handling of format specifiers
s390/zcrypt: Fix AP queue handling if queue is full
|
|
Pull virtio fix from Michael Tsirkin:
"This includes a single fix for virtio ccw error handling"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio/s390: handle error values in irb
|
|
Commit 1299653affa4 ("sh_eth: fix descriptor access endianness") only
addressed the 32-bit buffer address field byte-swapping but the driver
still accesses 16-bit frame/buffer length descriptor fields without the
necessary byte-swapping -- which should affect the big-endian kernels.
In order to be able to use {cpu|edmac}_to_{edmac|cpu}(), we need to declare
the RX/TX descriptor word 1 as a 32-bit field and use shifts/masking to
access the 16-bit subfields (which gets rid of the ugly #ifdef'ery too)...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
as good.
Packets that arrive from real hardware devices have ip_summed ==
CHECKSUM_UNNECESSARY if the hardware verified the checksums, or
CHECKSUM_NONE if the packet is bad or it was unable to verify it. The
current version of veth will replace CHECKSUM_NONE with
CHECKSUM_UNNECESSARY, which causes corrupt packets routed from hardware to
a veth device to be delivered to the application. This caused applications
at Twitter to receive corrupt data when network hardware was corrupting
packets.
We believe this was added as an optimization to skip computing and
verifying checksums for communication between containers. However, locally
generated packets have ip_summed == CHECKSUM_PARTIAL, so the code as
written does nothing for them. As far as we can tell, after removing this
code, these packets are transmitted from one stack to another unmodified
(tcpdump shows invalid checksums on both sides, as expected), and they are
delivered correctly to applications. We didn’t test every possible network
configuration, but we tried a few common ones such as bridging containers,
using NAT between the host and a container, and routing from hardware
devices to containers. We have effectively deployed this in production at
Twitter (by disabling RX checksum offloading on veth devices).
This code dates back to the first version of the driver, commit
<e314dbdc1c0dc6a548ecf> ("[NET]: Virtual ethernet device driver"), so I
suspect this bug occurred mostly because the driver API has evolved
significantly since then. Commit <0b7967503dc97864f283a> ("net/veth: Fix
packet checksumming") (in December 2010) fixed this for packets that get
created locally and sent to hardware devices, by not changing
CHECKSUM_PARTIAL. However, the same issue still occurs for packets coming
in from hardware devices.
Co-authored-by: Evan Jones <ej@evanjones.ca>
Signed-off-by: Evan Jones <ej@evanjones.ca>
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Vijay Pandurangan <vijayp@vijayp.ca>
Acked-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
0x4e is the runtime address normally associated with perihperal ICs.
0x45 is not a valid runtime address.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The primary PMICs use 0x3a3 as their hardware address, not 0x3e3.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
blk_end_request_all may free request, so we need to save
request_queue pointer before blk_end_request_all call.
The problem was introduced in commit cf8ecc5a8455266f8d51
("null_blk: guarantee device restart in all irq modes")
and causes general protection fault with slab poisoning
enabled.
Fixes: cf8ecc5a8455266f8d51 ("null_blk: guarantee device
restart in all irq modes")
Signed-off-by: Mike Krinkin <krinkin.m.u@gmail.com>
Reviewed-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
This patch fixes a lost request discovered during IO + hot removal.
The driver's pci removal deletes gendisks prior to shutting down the
controller to allow dirty data to sync. Dirty data can not be synced on
a surprise removal, though, and would potentially block indefinitely.
The driver previously had marked the queue as dying in this scenario
to prevent new requests from attempting, however it will still block
for requests that already entered the queue. This patch fixes this by
quiescing IO first, then aborting the requeued requests before deleting
disks.
Reported-by: Sujith Pandel <sujith_pandel@dell.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Tested-by: Sujith Pandel <sujith_pandel@dell.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
The total delay of HDMI hotplug detecting with 30ms have already
been split into a resolution of 3 retries of 10ms each, for the worst
cases. But it still suffered from only waiting 10ms at most in
intel_hdmi_detect(). This patch corrects it by reading hotplug status
with 4 times at most for 30ms delay.
v2:
- straight up to loop execution for more clear in code readability
- mdelay will replace with msleep by Daniel's new patch
drm/i915: mdelay(10) considered harmful
- suggest to re-evaluate try times for being compatible to old HDMI monitor
Reviewed-by: Cooper Chiou <cooper.chiou@intel.com>
Tested-by: Gary Wang <gary.c.wang@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Gavin Hindman <gavin.hindman@intel.com>
Cc: Sonika Jindal <sonika.jindal@intel.com>
Cc: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: Gary Wang <gary.c.wang@intel.com>
[danvet: fixup conflict with s/mdelay/msleep/ patch.]
Cc: drm-intel-fixes@lists.freedesktop.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
(cherry picked from commit 61fb3980dd396880ffba48523b1e27579868b82b)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
I missed this myself when reviewing
commit 237ed86c693d8a8e4db476976aeb30df4deac74b
Author: Sonika Jindal <sonika.jindal@intel.com>
Date: Tue Sep 15 09:44:20 2015 +0530
drm/i915: Check live status before reading edid
Long sleeps like this really shouldn't waste cpu cycles spinning.
Cc: Sonika Jindal <sonika.jindal@intel.com>
Cc: "Wang, Gary C" <gary.c.wang@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1449859455-32609-1-git-send-email-daniel.vetter@ffwll.ch
Reviewed-by: Sonika Jindal <sonika.jindal@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
(cherry picked from commit 71a199bacb398ee54eeac001699257dda083a455)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
The vma may have been rebound between the last time the cursor was
enabled and now, so skipping the cursor gtt offset deduction is not
safe unless we would also reset cursor_bo to NULL when disabling the
cursor. Just thow cursor_bo to the bin instead since it's lost all
other uses thanks to universal plane support.
Chris pointed out that cursor updates are currently too slow
via universal planes that micro optimizations like these wouldn't
even help.
v2: Add a note about futility of micro optimizations (Chris)
Cc: drm-intel-fixes@lists.freedesktop.org
References: http://lists.freedesktop.org/archives/intel-gfx/2015-December/082976.html
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450107302-17171-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
(cherry picked from commit 1264859d648c4bdc9f0a098efbff90cbf462a075)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
Turns out CHV pipe C was glued on somewhat poorly, and there's something
wrong with the cursor. If the cursor straddles the left screen edge,
and is then moved away from the edge or disabled, the pipe will often
underrun. If enough underruns are triggered quickly enough the pipe
will fall over and die (it just scans out a solid color and reports
a constant underrun). We need to turn the disp2d power well off and
on again to recover the pipe.
None of that is very nice for the user, so let's just refuse to place
the cursor in the compromised position. The ddx appears to fall back
to swcursor when the ioctl returns an error, so theoretically there's
no loss of functionality for the user (discounting swcursor bugs).
I suppose most cursors images actually have the hotspot not exactly
at 0,0 so under typical conditions the fallback will in fact kick in
as soon as the cursor touches the left edge of the screen.
Any atomic compositor should anyway be prepared to fall back to
GPU composition when things don't work out, so there should be no
problem with those.
Other things that I tried to solve this include flipping all
display related clock gating knobs I could find, increasing the
minimum gtt alignment all the way up to 512k. I also tried to see
if there are more specific screen coordinates that hit the bug, but
the findings were somewhat inconclusive. Sometimes the failures
happen almost across the whole left edge, sometimes more at the very
top and around the bottom half. I wasn't able to find any real pattern
to these variations, so it seems our only choice is to just refuse
to straddle the left screen edge at all.
Cc: stable@vger.kernel.org
Cc: Jason Plum <max@warheads.net>
Testcase: igt/kms_chv_cursor_fail
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92826
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450459479-16286-1-git-send-email-ville.syrjala@linux.intel.com
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
(cherry picked from commit b29ec92c4f5e6d45d8bae8194e664427a01c6687)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
Limit busywaiting only to the request currently being processed by the
GPU. If the request is not currently being processed by the GPU, there
is a very low likelihood of it being completed within the 2 microsecond
spin timeout and so we will just be wasting CPU cycles.
v2: Check for logical inversion when rebasing - we were incorrectly
checking for this request being active, and instead busywaiting for
when the GPU was not yet processing the request of interest.
v3: Try another colour for the seqno names.
v4: Another colour for the function names.
v5: Remove the forced coherency when checking for the active request. On
reflection and plenty of recent experimentation, the issue is not a
cache coherency problem - but an irq/seqno ordering problem (timing issue).
Here, we do not need the w/a to force ordering of the read with an
interrupt.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: "Rogozhkin, Dmitry V" <dmitry.v.rogozhkin@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: Eero Tamminen <eero.t.tamminen@intel.com>
Cc: "Rantala, Valtteri" <valtteri.rantala@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449833608-22125-4-git-send-email-chris@chris-wilson.co.uk
(cherry picked from commit 821485dc2ad665f136c57ee589bf7a8210160fe2)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
When waiting for high frequency requests, the finite amount of time
required to set up the irq and wait upon it limits the response rate. By
busywaiting on the request completion for a short while we can service
the high frequency waits as quick as possible. However, if it is a slow
request, we want to sleep as quickly as possible. The tradeoff between
waiting and sleeping is roughly the time it takes to sleep on a request,
on the order of a microsecond. Based on measurements of synchronous
workloads from across big core and little atom, I have set the limit for
busywaiting as 10 microseconds. In most of the synchronous cases, we can
reduce the limit down to as little as 2 miscroseconds, but that leaves
quite a few test cases regressing by factors of 3 and more.
The code currently uses the jiffie clock, but that is far too coarse (on
the order of 10 milliseconds) and results in poor interactivity as the
CPU ends up being hogged by slow requests. To get microsecond resolution
we need to use a high resolution timer. The cheapest of which is polling
local_clock(), but that is only valid on the same CPU. If we switch CPUs
because the task was preempted, we can also use that as an indicator that
the system is too busy to waste cycles on spinning and we should sleep
instead.
__i915_spin_request was introduced in
commit 2def4ad99befa25775dd2f714fdd4d92faec6e34 [v4.2]
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Tue Apr 7 16:20:41 2015 +0100
drm/i915: Optimistically spin for the request completion
v2: Drop full u64 for unsigned long - the timer is 32bit wraparound safe,
so we can use native register sizes on smaller architectures. Mention
the approximate microseconds units for elapsed time and add some extra
comments describing the reason for busywaiting.
v3: Raise the limit to 10us
v4: Now 5us.
Reported-by: Jens Axboe <axboe@kernel.dk>
Link: https://lkml.org/lkml/2015/11/12/621
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: "Rogozhkin, Dmitry V" <dmitry.v.rogozhkin@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: Eero Tamminen <eero.t.tamminen@intel.com>
Cc: "Rantala, Valtteri" <valtteri.rantala@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449833608-22125-3-git-send-email-chris@chris-wilson.co.uk
(cherry picked from commit ca5b721e238226af1d767103ac852aeb8e4c0764)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
