| Age | Commit message (Collapse) | Author |
|---|
|
cfi_ppb_unlock() walks all flash chips when unlocking sectors,
avoid walking chips unaffected by the unlock operation.
Fixes: 1648eaaa1575 ("mtd: cfi_cmdset_0002: Support Persistent Protection Bits (PPB) locking")
Cc: stable@vger.kernel.org
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
|
|
The "sector is in requested range" test used to determine whether
sectors should be re-locked or not is done on a variable that is reset
everytime we cross a chip boundary, which can lead to some blocks being
re-locked while the caller expect them to be unlocked.
Fix the check to make sure this cannot happen.
Fixes: 1648eaaa1575 ("mtd: cfi_cmdset_0002: Support Persistent Protection Bits (PPB) locking")
Cc: stable@vger.kernel.org
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
|
|
cfi_ppb_unlock() tries to relock all sectors that were locked before
unlocking the whole chip.
This locking used the chip start address + the FULL offset from the
first flash chip, thereby forming an illegal address. Fix that by using
the chip offset(adr).
Fixes: 1648eaaa1575 ("mtd: cfi_cmdset_0002: Support Persistent Protection Bits (PPB) locking")
Cc: stable@vger.kernel.org
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
|
|
do_ppb_xxlock() fails to add chip->start when querying for lock status
(and chip_ready test), which caused false status reports.
Fix that by adding adr += chip->start and adjust call sites
accordingly.
Fixes: 1648eaaa1575 ("mtd: cfi_cmdset_0002: Support Persistent Protection Bits (PPB) locking")
Cc: stable@vger.kernel.org
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
|
|
Make sure we flag all broken chips as not supporting this feature.
Also move this logic to a new function to keep things readable.
Fixes: 34c5c01e0c8c ("mtd: rawnand: macronix: nack the support of changing timings for one chip")
Cc: <stable@vger.kernel.org>
Signed-off-by: Mason Yang <masonccyang@mxic.com.tw>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Positive return value from read_oob() is making false BAD
blocks. For some of the NAND controllers, OOB bytes will be
protected with ECC and read_oob() will return number of bitflips.
If there is any bitflip in ECC protected OOB bytes for BAD block
status page, then that block is getting treated as BAD.
Fixes: c120e75e0e7d ("mtd: nand: use read_oob() instead of cmdfunc() for bad block check")
Cc: <stable@vger.kernel.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
|
|
The v21 version of the NAND flash controller contains a Spare Area Size
Register (SPAS) at offset 0x10. Its setting defaults to the maximum
spare area size of 218 bytes. The size that is set in this register is
used by the controller when it calculates the ECC bytes internally in
hardware.
Usually, this register is updated from settings in the IIM fuses when
the system is booting from NAND flash. For other boot media, however,
the SPAS register remains at the default setting, which may not work for
the particular flash chip on the board. The same goes for flash chips
whose configuration cannot be set in the IIM fuses (e.g. chips with 2k
sector size and 128 bytes spare area size can't be configured in the IIM
fuses on imx25 systems).
Set the SPAS register explicitly during the preset operation. Derive the
register value from mtd->oobsize that was detected during probe by
decoding the flash chip's ID bytes.
While at it, rename the define for the spare area register's offset to
NFC_V21_RSLTSPARE_AREA. The register at offset 0x10 on v1 controllers is
different from the register on v21 controllers.
Fixes: d484018 ("mtd: mxc_nand: set NFC registers after reset")
Cc: stable@vger.kernel.org
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
|
|
Add ONFI_FEATURE_ON_DIE_ECC to the set/get features list for Micron
NAND flash.
Fixes: 789157e41a06 ("mtd: rawnand: allow vendors to declare (un)supported features")
Cc: <stable@vger.kernel.org>
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
|
|
Pull block fixes from Jens Axboe:
"A collection of fixes that should go into -rc1. This contains:
- bsg_open vs bsg_unregister race fix (Anatoliy)
- NVMe pull request from Christoph, with fixes for regressions in
this window, FC connect/reconnect path code unification, and a
trace point addition.
- timeout fix (Christoph)
- remove a few unused functions (Christoph)
- blk-mq tag_set reinit fix (Roman)"
* tag 'for-linus-20180616' of git://git.kernel.dk/linux-block:
bsg: fix race of bsg_open and bsg_unregister
block: remov blk_queue_invalidate_tags
nvme-fabrics: fix and refine state checks in __nvmf_check_ready
nvme-fabrics: handle the admin-only case properly in nvmf_check_ready
nvme-fabrics: refactor queue ready check
blk-mq: remove blk_mq_tagset_iter
nvme: remove nvme_reinit_tagset
nvme-fc: fix nulling of queue data on reconnect
nvme-fc: remove reinit_request routine
blk-mq: don't time out requests again that are in the timeout handler
nvme-fc: change controllers first connect to use reconnect path
nvme: don't rely on the changed namespace list log
nvmet: free smart-log buffer after use
nvme-rdma: fix error flow during mapping request data
nvme: add bio remapping tracepoint
nvme: fix NULL pointer dereference in nvme_init_subsystem
blk-mq: reinit q->tag_set_list entry only after grace period
|
|
Pull documentation fixes from Mauro Carvalho Chehab:
"This solves a series of broken links for files under Documentation,
and improves a script meant to detect such broken links (see
scripts/documentation-file-ref-check).
The changes on this series are:
- can.rst: fix a footnote reference;
- crypto_engine.rst: Fix two parsing warnings;
- Fix a lot of broken references to Documentation/*;
- improve the scripts/documentation-file-ref-check script, in order
to help detecting/fixing broken references, preventing
false-positives.
After this patch series, only 33 broken references to doc files are
detected by scripts/documentation-file-ref-check"
* tag 'docs-broken-links' of git://linuxtv.org/mchehab/experimental: (26 commits)
fix a series of Documentation/ broken file name references
Documentation: rstFlatTable.py: fix a broken reference
ABI: sysfs-devices-system-cpu: remove a broken reference
devicetree: fix a series of wrong file references
devicetree: fix name of pinctrl-bindings.txt
devicetree: fix some bindings file names
MAINTAINERS: fix location of DT npcm files
MAINTAINERS: fix location of some display DT bindings
kernel-parameters.txt: fix pointers to sound parameters
bindings: nvmem/zii: Fix location of nvmem.txt
docs: Fix more broken references
scripts/documentation-file-ref-check: check tools/*/Documentation
scripts/documentation-file-ref-check: get rid of false-positives
scripts/documentation-file-ref-check: hint: dash or underline
scripts/documentation-file-ref-check: add a fix logic for DT
scripts/documentation-file-ref-check: accept more wildcards at filenames
scripts/documentation-file-ref-check: fix help message
media: max2175: fix location of driver's companion documentation
media: v4l: fix broken video4linux docs locations
media: dvb: point to the location of the old README.dvb-usb file
...
|
|
Pull fbdev updates from Bartlomiej Zolnierkiewicz:
"There is nothing really major here, few small fixes, some cleanups and
dead drivers removal:
- mark omapfb drivers as orphans in MAINTAINERS file (Tomi Valkeinen)
- add missing module license tags to omap/omapfb driver (Arnd
Bergmann)
- add missing GPIOLIB dependendy to omap2/omapfb driver (Arnd
Bergmann)
- convert savagefb, aty128fb & radeonfb drivers to use msleep & co.
(Jia-Ju Bai)
- allow COMPILE_TEST build for viafb driver (media part was reviewed
by media subsystem Maintainer)
- remove unused MERAM support from sh_mobile_lcdcfb and shmob-drm
drivers (drm parts were acked by shmob-drm driver Maintainer)
- remove unused auo_k190xfb drivers
- misc cleanups (Souptick Joarder, Wolfram Sang, Markus Elfring, Andy
Shevchenko, Colin Ian King)"
* tag 'fbdev-v4.18' of git://github.com/bzolnier/linux: (26 commits)
fb_omap2: add gpiolib dependency
video/omap: add module license tags
MAINTAINERS: make omapfb orphan
video: fbdev: pxafb: match_string() conversion fixup
video: fbdev: nvidia: fix spelling mistake: "scaleing" -> "scaling"
video: fbdev: fix spelling mistake: "frambuffer" -> "framebuffer"
video: fbdev: pxafb: Convert to use match_string() helper
video: fbdev: via: allow COMPILE_TEST build
video: fbdev: remove unused sh_mobile_meram driver
drm: shmobile: remove unused MERAM support
video: fbdev: sh_mobile_lcdcfb: remove unused MERAM support
video: fbdev: remove unused auo_k190xfb drivers
video: omap: Improve a size determination in omapfb_do_probe()
video: sm501fb: Improve a size determination in sm501fb_probe()
video: fbdev-MMP: Improve a size determination in path_init()
video: fbdev-MMP: Delete an error message for a failed memory allocation in two functions
video: auo_k190x: Delete an error message for a failed memory allocation in auok190x_common_probe()
video: sh_mobile_lcdcfb: Delete an error message for a failed memory allocation in two functions
video: sh_mobile_meram: Delete an error message for a failed memory allocation in sh_mobile_meram_probe()
video: fbdev: sh_mobile_meram: Drop SUPERH platform dependency
...
|
|
Pull networking fixes from David Miller:
1) Various netfilter fixlets from Pablo and the netfilter team.
2) Fix regression in IPVS caused by lack of PMTU exceptions on local
routes in ipv6, from Julian Anastasov.
3) Check pskb_trim_rcsum for failure in DSA, from Zhouyang Jia.
4) Don't crash on poll in TLS, from Daniel Borkmann.
5) Revert SO_REUSE{ADDR,PORT} change, it regresses various things
including Avahi mDNS. From Bart Van Assche.
6) Missing of_node_put in qcom/emac driver, from Yue Haibing.
7) We lack checking of the TCP checking in one special case during SYN
receive, from Frank van der Linden.
8) Fix module init error paths of mac80211 hwsim, from Johannes Berg.
9) Handle 802.1ad properly in stmmac driver, from Elad Nachman.
10) Must grab HW caps before doing quirk checks in stmmac driver, from
Jose Abreu.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (81 commits)
net: stmmac: Run HWIF Quirks after getting HW caps
neighbour: skip NTF_EXT_LEARNED entries during forced gc
net: cxgb3: add error handling for sysfs_create_group
tls: fix waitall behavior in tls_sw_recvmsg
tls: fix use-after-free in tls_push_record
l2tp: filter out non-PPP sessions in pppol2tp_tunnel_ioctl()
l2tp: reject creation of non-PPP sessions on L2TPv2 tunnels
mlxsw: spectrum_switchdev: Fix port_vlan refcounting
mlxsw: spectrum_router: Align with new route replace logic
mlxsw: spectrum_router: Allow appending to dev-only routes
ipv6: Only emit append events for appended routes
stmmac: added support for 802.1ad vlan stripping
cfg80211: fix rcu in cfg80211_unregister_wdev
mac80211: Move up init of TXQs
mac80211_hwsim: fix module init error paths
cfg80211: initialize sinfo in cfg80211_get_station
nl80211: fix some kernel doc tag mistakes
hv_netvsc: Fix the variable sizes in ipsecv2 and rsc offload
rds: avoid unenecessary cong_update in loop transport
l2tp: clean up stale tunnel or session in pppol2tp_connect's error path
...
|
|
Pull virtio updates from Michael Tsirkin:
"virtio, vhost: features, fixes
- PCI virtual function support for virtio
- DMA barriers for virtio strong barriers
- bugfixes"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio: update the comments for transport features
virtio_pci: support enabling VFs
vhost: fix info leak due to uninitialized memory
virtio_ring: switch to dma_XX barriers for rpmsg
|
|
As files move around, their previous links break. Fix the
references for them.
Acked-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
|
|
As we move stuff around, some doc references are broken. Fix some of
them via this script:
./scripts/documentation-file-ref-check --fix
Manually checked that produced results are valid.
Acked-by: Matthias Brugger <matthias.bgg@gmail.com>
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Miguel Ojeda <miguel.ojeda.sandonis@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
|
|
There's a missing ".rst" at the doc's file name.
Acked-by: Ramesh Shanmugasundaram <Ramesh.shanmugasundaram@bp.renesas.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
|
|
There are several places pointing to old documentation files:
Documentation/video4linux/API.html
Documentation/video4linux/bttv/
Documentation/video4linux/cx2341x/fw-encoder-api.txt
Documentation/video4linux/m5602.txt
Documentation/video4linux/v4l2-framework.txt
Documentation/video4linux/videobuf
Documentation/video4linux/Zoran
Make them point to the new location where available, removing
otherwise.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
|
|
This file got renamed, but the references still point to the
old place.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
|
|
This script was moved out of Documentation/dvb, but the
links weren't updated.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
|
|
As we move stuff around, some doc references are broken. Fix some of
them via this script:
./scripts/documentation-file-ref-check --fix
Manually checked if the produced result is valid, removing a few
false-positives.
Acked-by: Takashi Iwai <tiwai@suse.de>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Coly Li <colyli@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
|
|
The script:
./scripts/documentation-file-ref-check --fix
Gives multiple hints for broken references on some files.
Manually use the one that applies for some files.
Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Acked-by: James Morris <james.morris@microsoft.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Jonathan Corbet <corbet@lwn.net>
|
|
Currently we were running HWIF quirks before getting HW capabilities.
This is not right because some HWIF callbacks depend on HW caps.
Lets save the quirks callback and use it in a later stage.
This fixes Altera socfpga.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Fixes: 5f0456b43140 ("net: stmmac: Implement logic to automatically select HW Interface")
Reported-by: Dinh Nguyen <dinh.linux@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Vitor Soares <soares@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When sysfs_create_group fails, the lack of error-handling code may
cause unexpected results.
This patch adds error-handling code after calling sysfs_create_group.
Signed-off-by: Zhouyang Jia <jiazhouyang09@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Switchdev notifications for addition of SWITCHDEV_OBJ_ID_PORT_VLAN are
distributed not only on clean addition, but also when flags on an
existing VLAN are changed. mlxsw_sp_bridge_port_vlan_add() calls
mlxsw_sp_port_vlan_get() to get at the port_vlan in question, which
implicitly references the object. This then leads to discrepancies in
reference counting when the VLAN is removed. spectrum.c warns about the
problem when the module is removed:
[13578.493090] WARNING: CPU: 0 PID: 2454 at drivers/net/ethernet/mellanox/mlxsw/spectrum.c:2973 mlxsw_sp_port_remove+0xfd/0x110 [mlxsw_spectrum]
[...]
[13578.627106] Call Trace:
[13578.629617] mlxsw_sp_fini+0x2a/0xe0 [mlxsw_spectrum]
[13578.634748] mlxsw_core_bus_device_unregister+0x3e/0x130 [mlxsw_core]
[13578.641290] mlxsw_pci_remove+0x13/0x40 [mlxsw_pci]
[13578.646238] pci_device_remove+0x31/0xb0
[13578.650244] device_release_driver_internal+0x14f/0x220
[13578.655562] driver_detach+0x32/0x70
[13578.659183] bus_remove_driver+0x47/0xa0
[13578.663134] pci_unregister_driver+0x1e/0x80
[13578.667486] mlxsw_sp_module_exit+0xc/0x3fa [mlxsw_spectrum]
[13578.673207] __x64_sys_delete_module+0x13b/0x1e0
[13578.677888] ? exit_to_usermode_loop+0x78/0x80
[13578.682374] do_syscall_64+0x39/0xe0
[13578.685976] entry_SYSCALL_64_after_hwframe+0x44/0xa9
Fix by putting the port_vlan when mlxsw_sp_port_vlan_bridge_join()
determines it's a flag-only change.
Fixes: b3529af6bb0d ("spectrum: Reference count VLAN entries")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit f34436a43092 ("net/ipv6: Simplify route replace and appending
into multipath route") changed the IPv6 route replace logic so that the
first matching route (i.e., same metric) is replaced.
Have mlxsw replace the first matching route as well.
Fixes: f34436a43092 ("net/ipv6: Simplify route replace and appending into multipath route")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit f34436a43092 ("net/ipv6: Simplify route replace and appending
into multipath route") changed the IPv6 route append logic so that
dev-only routes can be appended and not only gatewayed routes.
Align mlxsw with the new behaviour.
Fixes: f34436a43092 ("net/ipv6: Simplify route replace and appending into multipath route")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
A handful of fixes:
* missing RCU grace period enforcement led to drivers freeing
data structures before; fix from Dedy Lansky.
* hwsim module init error paths were messed up; fixed it myself
after a report from Colin King (who had sent a partial patch)
* kernel-doc tag errors; fix from Luca Coelho
* initialize the on-stack sinfo data structure when getting
station information; fix from Sven Eckelmann
* TXQ state dumping is now done from init, and when TXQs aren't
initialized yet at that point, bad things happen, move the
initialization; fix from Toke Høiland-Jørgensen.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
stmmac reception handler calls stmmac_rx_vlan() to strip the vlan before
calling napi_gro_receive().
The function assumes VLAN tagged frames are always tagged with
802.1Q protocol, and assigns ETH_P_8021Q to the skb by hard-coding
the parameter on call to __vlan_hwaccel_put_tag() .
This causes packets not to be passed to the VLAN slave if it was created
with 802.1AD protocol
(ip link add link eth0 eth0.100 type vlan proto 802.1ad id 100).
This fix passes the protocol from the VLAN header into
__vlan_hwaccel_put_tag() instead of using the hard-coded value of
ETH_P_8021Q.
NETIF_F_HW_VLAN_STAG_RX check was added and the strip action is now
dependent on the correct combination of features and the detected vlan tag.
NETIF_F_HW_VLAN_STAG_RX feature was added to be in line with the driver
actual abilities.
Signed-off-by: Elad Nachman <eladn@gilat.com>
Reviewed-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull NVMe fixes from Christoph:
"Fix various little regressions introduced in this merge window, plus
a rework of the fibre channel connect and reconnect path to share the
code instead of having separate sets of bugs. Last but not least a
trivial trace point addition from Hannes."
* 'nvme-4.18' of git://git.infradead.org/nvme:
nvme-fabrics: fix and refine state checks in __nvmf_check_ready
nvme-fabrics: handle the admin-only case properly in nvmf_check_ready
nvme-fabrics: refactor queue ready check
blk-mq: remove blk_mq_tagset_iter
nvme: remove nvme_reinit_tagset
nvme-fc: fix nulling of queue data on reconnect
nvme-fc: remove reinit_request routine
nvme-fc: change controllers first connect to use reconnect path
nvme: don't rely on the changed namespace list log
nvmet: free smart-log buffer after use
nvme-rdma: fix error flow during mapping request data
nvme: add bio remapping tracepoint
nvme: fix NULL pointer dereference in nvme_init_subsystem
|
|
We didn't free the workqueue on any errors, nor did we
correctly check for rhashtable allocation errors, nor
did we free the hashtable on error.
Reported-by: Colin King <colin.king@canonical.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
|
|
- make sure we only allow internally generates commands in any non-live
state
- only allow connect commands on non-live queues when actually in the
new or connecting states
- treat all other non-live, non-dead states the same as a default
cach-all
This fixes a regression where we could not shutdown a controller
orderly as we didn't allow the internal generated Property Set
command, and also ensures we don't accidentally let a Connect command
through in the wrong state.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: James Smart <james.smart@broadcom.com>
|
|
In the ADMIN_ONLY state we don't have any I/O queues, but we should accept
all admin commands without further checks.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: James Smart <james.smart@broadcom.com>
|
|
Move the is_connected check to the fibre channel transport, as it has no
meaning for other transports. To facilitate this split out a new
nvmf_fail_nonready_command helper that is called by the transport when
it is asked to handle a command on a queue that is not ready.
Also avoid a function call for the queue live fast path by inlining
the check.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: James Smart <james.smart@broadcom.com>
|
|
Pull amd drm fixes from Dave Airlie:
"Just a single set of AMD fixes for stuff in -next for -rc1"
* tag 'drm-next-2018-06-15' of git://anongit.freedesktop.org/drm/drm: (47 commits)
drm/amd/powerplay: Set higher SCLK&MCLK frequency than dpm7 in OD (v2)
drm/amd/powerplay: remove uncessary extra gfxoff control call
drm/amdgpu: fix parsing indirect register list v2
drm/amd/include: Update df 3.6 mask and shift definition
drm/amd/pp: Fix OD feature enable failed on Vega10 workstation cards
drm/amd/display: Fix stale buffer object (bo) use
drm/amd/pp: initialize result to before or'ing in data
drm/amd/powerplay: fix wrong clock adjust sequence
drm/amdgpu: Grab/put runtime PM references in atomic_commit_tail()
drm/amd/powerplay: fix missed hwmgr check warning before call gfx_off_control handler
drm/amdgpu: fix CG enabling hang with gfxoff enabled
drm/amdgpu: fix clear_all and replace handling in the VM (v2)
drm/amdgpu: add checking for sos version
drm/amdgpu: fix the missed vcn fw version report
Revert "drm/amdgpu: Add an ATPX quirk for hybrid laptop"
drm/amdgpu/df: fix potential array out-of-bounds read
drm/amdgpu: Fix NULL pointer when load kfd driver with PP block is disabled
drm/gfx9: Update gc goldensetting for vega20.
drm/amd/pp: Allow underclocking when od table is empty in vbios
drm/amdgpu/display: check if ppfuncs exists before using it
...
|
|
These fields in struct ndis_ipsecv2_offload and struct ndis_rsc_offload
are one byte according to the specs. This patch defines them with the
right size. These structs are not in use right now, but will be used soon.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
into drm-next
Fixes for 4.18. Highlights:
- Fixes for gfxoff on Raven
- Remove an ATPX quirk now that the root cause is fixed
- Runtime PM fixes
- Vega20 register header update
- Wattman fixes
- Misc bug fixes
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180614141428.2909-1-alexander.deucher@amd.com
|
|
Errors are already reported in xemaclite_mdio_setup so avoid
reporting it again.
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove unused 'has_mdio' flag.
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since 'has_mdio' flag is not used,sequence insmod->rmmod-> insmod
leads to failure as MDIO unregister doesn't happen in .remove().
Fix it by checking MII bus pointer instead.
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To ensure MDIO bus is not double freed in remove() path
assign lp->mii_bus after MDIO bus registration.
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add missing of_node_put() call for device node returned by
of_parse_phandle().
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Merge more updates from Andrew Morton:
- MM remainders
- various misc things
- kcov updates
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (27 commits)
lib/test_printf.c: call wait_for_random_bytes() before plain %p tests
hexagon: drop the unused variable zero_page_mask
hexagon: fix printk format warning in setup.c
mm: fix oom_kill event handling
treewide: use PHYS_ADDR_MAX to avoid type casting ULLONG_MAX
mm: use octal not symbolic permissions
ipc: use new return type vm_fault_t
sysvipc/sem: mitigate semnum index against spectre v1
fault-injection: reorder config entries
arm: port KCOV to arm
sched/core / kcov: avoid kcov_area during task switch
kcov: prefault the kcov_area
kcov: ensure irq code sees a valid area
kernel/relay.c: change return type to vm_fault_t
exofs: avoid VLA in structures
coredump: fix spam with zero VMA process
fat: use fat_fs_error() instead of BUG_ON() in __fat_get_block()
proc: skip branch in /proc/*/* lookup
mremap: remove LATENCY_LIMIT from mremap to reduce the number of TLB shootdowns
mm/memblock: add missing include <linux/bootmem.h>
...
|
|
With PHYS_ADDR_MAX there is now a type safe variant for all bits set.
Make use of it.
Patch created using a semantic patch as follows:
// <smpl>
@@
typedef phys_addr_t;
@@
-(phys_addr_t)ULLONG_MAX
+PHYS_ADDR_MAX
// </smpl>
Link: http://lkml.kernel.org/r/20180419214204.19322-1-stefan@agner.ch
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com> [arm64]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arnd/playground
Pull inode timestamps conversion to timespec64 from Arnd Bergmann:
"This is a late set of changes from Deepa Dinamani doing an automated
treewide conversion of the inode and iattr structures from 'timespec'
to 'timespec64', to push the conversion from the VFS layer into the
individual file systems.
As Deepa writes:
'The series aims to switch vfs timestamps to use struct timespec64.
Currently vfs uses struct timespec, which is not y2038 safe.
The series involves the following:
1. Add vfs helper functions for supporting struct timepec64
timestamps.
2. Cast prints of vfs timestamps to avoid warnings after the switch.
3. Simplify code using vfs timestamps so that the actual replacement
becomes easy.
4. Convert vfs timestamps to use struct timespec64 using a script.
This is a flag day patch.
Next steps:
1. Convert APIs that can handle timespec64, instead of converting
timestamps at the boundaries.
2. Update internal data structures to avoid timestamp conversions'
Thomas Gleixner adds:
'I think there is no point to drag that out for the next merge
window. The whole thing needs to be done in one go for the core
changes which means that you're going to play that catchup game
forever. Let's get over with it towards the end of the merge window'"
* tag 'vfs-timespec64' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/playground:
pstore: Remove bogus format string definition
vfs: change inode times to use struct timespec64
pstore: Convert internal records to timespec64
udf: Simplify calls to udf_disk_stamp_to_time
fs: nfs: get rid of memcpys for inode times
ceph: make inode time prints to be long long
lustre: Use long long type to print inode time
fs: add timespec64_truncate()
|
|
Pull ceph updates from Ilya Dryomov:
"The main piece is a set of libceph changes that revamps how OSD
requests are aborted, improving CephFS ENOSPC handling and making
"umount -f" actually work (Zheng and myself).
The rest is mostly mount option handling cleanups from Chengguang and
assorted fixes from Zheng, Luis and Dongsheng.
* tag 'ceph-for-4.18-rc1' of git://github.com/ceph/ceph-client: (31 commits)
rbd: flush rbd_dev->watch_dwork after watch is unregistered
ceph: update description of some mount options
ceph: show ino32 if the value is different with default
ceph: strengthen rsize/wsize/readdir_max_bytes validation
ceph: fix alignment of rasize
ceph: fix use-after-free in ceph_statfs()
ceph: prevent i_version from going back
ceph: fix wrong check for the case of updating link count
libceph: allocate the locator string with GFP_NOFAIL
libceph: make abort_on_full a per-osdc setting
libceph: don't abort reads in ceph_osdc_abort_on_full()
libceph: avoid a use-after-free during map check
libceph: don't warn if req->r_abort_on_full is set
libceph: use for_each_request() in ceph_osdc_abort_on_full()
libceph: defer __complete_request() to a workqueue
libceph: move more code into __complete_request()
libceph: no need to call flush_workqueue() before destruction
ceph: flush pending works before shutdown super
ceph: abort osd requests on force umount
libceph: introduce ceph_osdc_abort_requests()
...
|
|
Unused now that all transports stopped using it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jens Axboe <axboe@kernel.dk>
|
|
The reconnect path is calling the init routines to clear a queue
structure. But the queue structure has state that perhaps needs
to persist as long as the controller is live.
Remove the nvme_fc_init_queue() calls on reconnect.
The nvme_fc_free_queue() calls will clear state bits and reset
any relevant queue state for a new connection.
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
The reinit_request routine is not necessary. Remove support for the
op callback.
As all that nvme_reinit_tagset() does is itterate and call the
reinit routine, it too has no purpose. Remove the call.
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
vfs-timespec64
Pull the timespec64 conversion from Deepa Dinamani:
"The series aims to switch vfs timestamps to use
struct timespec64. Currently vfs uses struct timespec,
which is not y2038 safe.
The flag patch applies cleanly. I've not seen the timestamps
update logic change often. The series applies cleanly on 4.17-rc6
and linux-next tip (top commit: next-20180517).
I'm not sure how to merge this kind of a series with a flag patch.
We are targeting 4.18 for this.
Let me know if you have other suggestions.
The series involves the following:
1. Add vfs helper functions for supporting struct timepec64 timestamps.
2. Cast prints of vfs timestamps to avoid warnings after the switch.
3. Simplify code using vfs timestamps so that the actual
replacement becomes easy.
4. Convert vfs timestamps to use struct timespec64 using a script.
This is a flag day patch.
I've tried to keep the conversions with the script simple, to
aid in the reviews. I've kept all the internal filesystem data
structures and function signatures the same.
Next steps:
1. Convert APIs that can handle timespec64, instead of converting
timestamps at the boundaries.
2. Update internal data structures to avoid timestamp conversions."
I've pulled it into a branch based on top of the NFS changes that
are now in mainline, so I could resolve the non-obvious conflict
between the two while merging.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Fix the issue that SCLK&MCLK can't be set higher than dpm7 when
OD is enabled in SMU7.
v2: fix warning (Alex)
Signed-off-by: Kenneth Feng <kenneth.feng@amd.com>
Acked-by: Rex Zhu<rezhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
