| Age | Commit message (Collapse) | Author |
|---|
|
The split into multiple structures of the "ll" register bank is
impractical. It makes it hard to add ll_lfps_timers_2 which is
at offset 0x794, which is outside of the existing "lfps" structure
and would require us to add yet another one.
Instead, move all the "ll" registers into a single usb338x_ll_regs
structure, and add ll_lfps_timers_2 while at it. It will be used
in a subsequent patch.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
While testing our host system using Microsoft's usb stack against our
gadget for various BESL values, we found an issue with their usb stack
when the recommended baseline BESL value is 0 (125us) or when the deep
BESL is 1 or less. The Windows host will issue a usb reset immediately
after it receives the extended BOS descriptor and the enumeration will
fail after a few attempts.
To keep compatibility with Microsoft's host usb stack, let's workaround
this issue by using the recommended baseline BESL of 1 (or 150us)
and clamp the deep BESL value within 2 to 15.
This was tested against Windows 10 build 18956.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Controller for OUT endpoints has shared on-chip buffers for all incoming
packets, including ep0out. It's FIFO buffer, so packets must be handled
by DMA in correct order. If the first packet in the buffer will not be
handled, then the following packets directed for other endpoints and
functions will be blocked.
Additionally the packets directed to one endpoint can block entire on-chip
buffers. In this case transfer to other endpoints also will blocked.
To resolve this issue after raising the descriptor missing interrupt
driver prepares internal usb_request object and use it to arm DMA
transfer.
The problematic situation was observed in case when endpoint has
been enabled but no usb_request were queued. Driver try detects
such endpoints and will use this workaround only for these endpoint.
Driver use limited number of buffer. This number can be set by macro
CDNS_WA2_NUM_BUFFERS.
Such blocking situation was observed on ACM gadget. For this function
host send OUT data packet but ACM function is not prepared for
this packet. It's cause that buffer placed in on chip memory block
transfer to other endpoints.
Issue has been fixed for DEV_VER_V2 version of controller.
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
This patch introduce new Cadence USBSS DRD driver to Linux kernel.
The Cadence USBSS DRD Controller is a highly configurable IP Core which
can be instantiated as Dual-Role Device (DRD), Peripheral Only and
Host Only (XHCI)configurations.
The current driver has been validated with FPGA platform. We have
support for PCIe bus, which is used on FPGA prototyping.
The host side of USBSS-DRD controller is compliant with XHCI
specification, so it works with standard XHCI Linux driver.
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Patch moves switch responsible for decoding descriptor type
outside snprintf. It improves code readability a little.
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Patch adds usb_decode_test_mode and usb_decode_device_feature functions,
which allow to make more readable and simplify the
usb_decode_set_clear_feature function.
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Patch moves some decoding functions from driver/usb/dwc3/debug.h driver
to driver/usb/common/debug.c file. These moved functions include:
dwc3_decode_get_status
dwc3_decode_set_clear_feature
dwc3_decode_set_address
dwc3_decode_get_set_descriptor
dwc3_decode_get_configuration
dwc3_decode_set_configuration
dwc3_decode_get_intf
dwc3_decode_set_intf
dwc3_decode_synch_frame
dwc3_decode_set_sel
dwc3_decode_set_isoch_delay
dwc3_decode_ctrl
These functions are used also in inroduced cdns3 driver.
All functions prefixes were changed from dwc3 to usb.
Also, function's parameters has been extended according to the name
of fields in standard SETUP packet.
Additionally, patch adds usb_decode_ctrl function to
include/linux/usb/ch9.h file.
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Set the recommended BESL deep and baseline values based on the gadget's
configuration parameters to the extended BOS descriptor. This feature
helps to optimize power savings by maximizing the opportunity for longer
L1 residency time.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
When operating with LPM signals, the controller asserts the deep
low-power signal (utmi_l1_suspend_n) to the phy when the BESL value of
the LPM token is equal to or greater than DCTL.HIRD_Thres[3:0] (and
with DCTL.HIRD_Thres[4] set). Otherwise, the shallow low-power signal
(utmi_sleep_n) is asserted. Set the recommended deep BESL equal to the
controller's DCTL.HIRD_Thres[3:0] setting, and set the baseline BESL
to 0 for the shallow low-power signal. This maximizes the opportunity
for L1 residency and optimizes power savings.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
dwc->hird_threshold field should store "snps,hird_threshold" property
only and not a combination of multiple properties. Remove the value of
"snps,is-utmi-l1-suspend" property from the field dwc->hird_threshold.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Static structure fsl_otg_initdata, of type fsl_otg_config, is used only
once, when the value of its field otg_port is assigned to another
variable. As fsl_otg_initdata.otg_port is of type u8, any changes to
its copy do not affect the original, and fsl_otg_initdata itself is
never modified. Hence make fsl_otg_initdata constant to protect it from
unintended modification.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Silence the following fall-through warning by adding a break statement:
drivers/usb/gadget/udc/lpc32xx_udc.c:2230:3: warning: this statement may
fall through [-Wimplicit-fallthrough=]
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
When going in suspend, in Device mode, then resuming back leads
to the following:
unbalanced disables for USB_PWR_EN
WARNING: CPU: 0 PID: 163 at ../drivers/regulator/core.c:2590 _regulator_disable+0x104/0x180
Hardware name: Amlogic Meson G12A U200 Development Board (DT)
[...]
pc : _regulator_disable+0x104/0x180
lr : _regulator_disable+0x104/0x180
[...]
Call trace:
_regulator_disable+0x104/0x180
regulator_disable+0x40/0x78
dwc3_meson_g12a_otg_mode_set+0x84/0xb0
dwc3_meson_g12a_irq_thread+0x58/0xb8
irq_thread_fn+0x28/0x80
irq_thread+0x118/0x1b8
kthread+0xf4/0x120
ret_from_fork+0x10/0x18
This disables the regulator if enabled on suspend, and the reverse on
resume.
Fixes: c99993376f72 ("usb: dwc3: Add Amlogic G12A DWC3 glue")
Tested-by: Kevin Hilman <khilman@baylibre.com>
Reported-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/usb/gadget/udc/lpc32xx_udc.c: In function ‘udc_protocol_cmd_r’:
drivers/usb/gadget/udc/lpc32xx_udc.c:744:6: warning: variable ‘tmp’ set but not used [-Wunused-but-set-variable]
drivers/usb/gadget/udc/lpc32xx_udc.c: In function ‘udc_handle_dma_ep’:
drivers/usb/gadget/udc/lpc32xx_udc.c:1994:14: warning: variable ‘epstatus’ set but not used [-Wunused-but-set-variable]
drivers/usb/gadget/udc/lpc32xx_udc.c: In function ‘udc_handle_ep0_setup’:
drivers/usb/gadget/udc/lpc32xx_udc.c:2200:22: warning: variable ‘wLength’ set but not used [-Wunused-but-set-variable]
It is not used since commit 90fccb529d24 ("usb: gadget: Gadget directory cleanup - group UDC drivers")
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
driver fails
If a gadget driver is in the pending drivers list, a UDC
becomes available and udc_bind_to_driver() fails, then it
gets deleted from the pending list.
i.e. list_del(&driver->pending) in check_pending_gadget_drivers().
Then if that gadget driver is unregistered,
usb_gadget_unregister_driver() does a list_del(&driver->pending)
again thus causing a page fault as that list entry has been poisoned
by the previous list_del().
Fix this by using list_del_init() instead of list_del() in
check_pending_gadget_drivers().
Test case:
- Make sure no UDC is available
- modprobe g_mass_storage file=wrongfile
- Load UDC driver so it becomes available
lun0: unable to open backing file: wrongfile
- modprobe -r g_mass_storage
[ 60.900431] Unable to handle kernel paging request at virtual address dead000000000108
[ 60.908346] Mem abort info:
[ 60.911145] ESR = 0x96000044
[ 60.914227] Exception class = DABT (current EL), IL = 32 bits
[ 60.920162] SET = 0, FnV = 0
[ 60.923217] EA = 0, S1PTW = 0
[ 60.926354] Data abort info:
[ 60.929228] ISV = 0, ISS = 0x00000044
[ 60.933058] CM = 0, WnR = 1
[ 60.936011] [dead000000000108] address between user and kernel address ranges
[ 60.943136] Internal error: Oops: 96000044 [#1] PREEMPT SMP
[ 60.948691] Modules linked in: g_mass_storage(-) usb_f_mass_storage libcomposite xhci_plat_hcd xhci_hcd usbcore ti_am335x_adc kfifo_buf omap_rng cdns3 rng_core udc_core crc32_ce xfrm_user crct10dif_ce snd_so6
[ 60.993995] Process modprobe (pid: 834, stack limit = 0x00000000c2aebc69)
[ 61.000765] CPU: 0 PID: 834 Comm: modprobe Not tainted 4.19.59-01963-g065f42a60499 #92
[ 61.008658] Hardware name: Texas Instruments SoC (DT)
[ 61.014472] pstate: 60000005 (nZCv daif -PAN -UAO)
[ 61.019253] pc : usb_gadget_unregister_driver+0x7c/0x108 [udc_core]
[ 61.025503] lr : usb_gadget_unregister_driver+0x30/0x108 [udc_core]
[ 61.031750] sp : ffff00001338fda0
[ 61.035049] x29: ffff00001338fda0 x28: ffff800846d40000
[ 61.040346] x27: 0000000000000000 x26: 0000000000000000
[ 61.045642] x25: 0000000056000000 x24: 0000000000000800
[ 61.050938] x23: ffff000008d7b0d0 x22: ffff0000088b07c8
[ 61.056234] x21: ffff000001100000 x20: ffff000002020260
[ 61.061530] x19: ffff0000010ffd28 x18: 0000000000000000
[ 61.066825] x17: 0000000000000000 x16: 0000000000000000
[ 61.072121] x15: 0000000000000000 x14: 0000000000000000
[ 61.077417] x13: ffff000000000000 x12: ffffffffffffffff
[ 61.082712] x11: 0000000000000030 x10: 7f7f7f7f7f7f7f7f
[ 61.088008] x9 : fefefefefefefeff x8 : 0000000000000000
[ 61.093304] x7 : ffffffffffffffff x6 : 000000000000ffff
[ 61.098599] x5 : 8080000000000000 x4 : 0000000000000000
[ 61.103895] x3 : ffff000001100020 x2 : ffff800846d40000
[ 61.109190] x1 : dead000000000100 x0 : dead000000000200
[ 61.114486] Call trace:
[ 61.116922] usb_gadget_unregister_driver+0x7c/0x108 [udc_core]
[ 61.122828] usb_composite_unregister+0x10/0x18 [libcomposite]
[ 61.128643] msg_cleanup+0x18/0xfce0 [g_mass_storage]
[ 61.133682] __arm64_sys_delete_module+0x17c/0x1f0
[ 61.138458] el0_svc_common+0x90/0x158
[ 61.142192] el0_svc_handler+0x2c/0x80
[ 61.145926] el0_svc+0x8/0xc
[ 61.148794] Code: eb03003f d10be033 54ffff21 a94d0281 (f9000420)
[ 61.154869] ---[ end trace afb22e9b637bd9a7 ]---
Segmentation fault
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
In function st_dwc3_probe, variable child_pdev takes the value returned
by of_find_device_by_node, which gets a device pointer but does not put
it. If child_pdev is not put before the probe function returns, it may
cause a reference leak. Hence put child_pdev after its last usage.
Issue found with Coccinelle.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
The local variable child in the function st_dwc3_probe takes the return
value of of_get_child_by_name, which gets a node and does not put it. If
the function returns without releasing child, this could cause a memory
error. Hence put child as soon as there is no more use for it. Also
create a new label, err_node_put, just before label undo_softreset; so
that err_node_put puts child. In between initialisation of child and its
first put, modify all statements that go to undo_softreset to now go to
err_node_put instead, from where they can fall through to
undo_softreset.
Issue found with Coccinelle.
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
This reverts
commit 6a4290cc28be1 ("usb: dwc3: gadget: set the OTG flag in dwc3 gadget driver.")
We don't yet support any of the OTG mechanisms (HNP/SRP/ADP)
and are not setting gadget->otg_caps, so don't set gadget->is_otg
flag.
If we do then we end up publishing a OTG1.0 descriptor in
the gadget descriptor which causes device enumeration to fail
if we are connected to a host with CONFIG_USB_OTG enabled.
Host side log without this patch
[ 96.720453] usb 1-1: new high-speed USB device number 2 using xhci-hcd
[ 96.901391] usb 1-1: Dual-Role OTG device on non-HNP port
[ 96.907552] usb 1-1: set a_alt_hnp_support failed: -32
[ 97.060447] usb 1-1: new high-speed USB device number 3 using xhci-hcd
[ 97.241378] usb 1-1: Dual-Role OTG device on non-HNP port
[ 97.247536] usb 1-1: set a_alt_hnp_support failed: -32
[ 97.253606] usb usb1-port1: attempt power cycle
[ 97.960449] usb 1-1: new high-speed USB device number 4 using xhci-hcd
[ 98.141383] usb 1-1: Dual-Role OTG device on non-HNP port
[ 98.147540] usb 1-1: set a_alt_hnp_support failed: -32
[ 98.300453] usb 1-1: new high-speed USB device number 5 using xhci-hcd
[ 98.481391] usb 1-1: Dual-Role OTG device on non-HNP port
[ 98.487545] usb 1-1: set a_alt_hnp_support failed: -32
[ 98.493532] usb usb1-port1: unable to enumerate USB device
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
We just accept them instead of stalling and return
zeros on GetTTState.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
When nuking requests, it's useful to display how many were
actually nuked. It has proven handy when debugging issues
where EP0 went in a wrong state.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
The state bit in the hub is sufficient
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
We had some dodgy code using the speed setting to decide whether a
port reset would reset the device or just enable it.
Instead, if the device is disabled and has a gadget attached, a
reset will enable it. If it's already enabled, a reset will
reset it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
.. before calling them
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
A disconnect may just suspend the hub in absence of a physical
disconnect detection. If we start rejecting requests, the mass
storage function gets into a spin trying to requeue the same
request for ever and hangs.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
When stalling EP0, we need to wait for an ACK interrupt,
otherwise we may get out of sync on the next setup packet
data phase. Also we need to ignore the direction when
processing that interrupt as the HW reports a potential
mismatch.
Implement this by adding a stall state to EP0. This fixes
some reported issues with mass storage and some hosts.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Otherwise, we can have a stale state after a disconnect and reconnect
causing errors on the first SETUP packet to the device.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
This bit should be only set when the port enable goes down, for
example, on errors. Not when it gets set after a port reset. Some
USB stacks seem to be sensitive to this and fails enumeration.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Use clk_bulk_prepare_enable() and clk_bulk_disable_unprepare() to
simplify code a bit. No functional change intended.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Use devres to get clocks and drop explicit clock freeing. No
functional change intended.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Commit 08f871a3aca2 ("usb: dwc3: host: convey the PHYs to xhci") added
forwarding of the generic PHYs from DWC3 core to the instantiated XHCI-plat
device. However XHCI(-plat) driver never gained support for generic PHYs,
thus the lookup added by that commit is never used. In meantime the commit
d64ff406e51e ("usb: dwc3: use bus->sysdev for DMA configuration")
incorrectly changed the device used for creating lookup, making the lookup
useless and generic PHYs inaccessible from XHCI device.
However since commit 178a0bce05cb ("usb: core: hcd: integrate the PHY
wrapper into the HCD core") USB HCD already handles generic PHYs acquired
from the HCD's 'sysdev', which in this case is DWC3 core device. This means
that creating any custom lookup entries for XHCI driver is no longer needed
and can be simply removed.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Starting from DWC_usb31 version 1.90a and later, the DCTL.CSFRST bit
will not be cleared until after all the internal clocks are synchronized
during soft-reset. This may take a little more than 50ms. Set the
polling rate at 20ms instead.
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
This enum is only used in drivers/usb/dwc3/dwc3-omap3.c
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Use use device_property_count_u32() directly, that makes code neater.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Instead of using to_pci_dev + pci_get_drvdata,
use dev_get_drvdata to make code simpler.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Use use device_property_count_u32() directly, that makes code neater.
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
When a gadget is disabled, kill_all_requests() can be called
simultaneously from both a user process via dwc2_hsotg_pullup() and from
the interrupt handler if the hardware detects disconnection.
Since we drop the lock in dwc2_hsotg_complete_request() in order to call
the completion handler, this means that the list is modified
concurrently and leads to an infinite loop in kill_all_requests().
Replace the foreach loop with a while-not-empty loop in order to remove
the danger of this concurrent modification.
Note: I observed this with threadirqs, I'm not sure if it can be
triggered without threaded interrupts.
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Mark switch cases where we are expecting to fall through.
This patch fixes the following warning (Building: at91_dt_defconfig arm):
drivers/usb/gadget/udc/atmel_usba_udc.c:329:13: warning: this statement may fall through [-Wimplicit-fallthrough=]
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Mark switch cases where we are expecting to fall through.
This patch fixes the following warning (Building: tct_hammer_defconfig arm):
drivers/usb/gadget/udc/s3c2410_udc.c:314:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
drivers/usb/gadget/udc/s3c2410_udc.c:418:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Pull tpm fixes from Jarkko Sakkinen:
"Two bug fixes that did not make into my first pull request"
* tag 'tpmdd-next-20190805' of git://git.infradead.org/users/jjs/linux-tpmdd:
tpm: tpm_ibm_vtpm: Fix unallocated banks
tpm: Fix null pointer dereference on chip register error path
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD fixes from Miquel Raynal:
"NAND:
- Fix Micron driver as some chips enable internal ECC correction
during their discovery while they advertize they do not have any.
Hyperbus:
- Restrict the build to only ARM64 SoCs (and compile testing) which
is what should have been done since the beginning.
- Fix Kconfig issue by selection something instead of implying it"
* tag 'mtd/fixes-for-5.3-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux:
mtd: hyperbus: Add hardware dependency to AM654 driver
mtd: hyperbus: Kconfig: Fix HBMC_AM654 dependencies
mtd: rawnand: micron: handle on-die "ECC-off" devices correctly
|
|
The nr_allocated_banks and allocated banks are initialized as part of
tpm_chip_register. Currently, this is done as part of auto startup
function. However, some drivers, like the ibm vtpm driver, do not run
auto startup during initialization. This results in uninitialized memory
issue and causes a kernel panic during boot.
This patch moves the pcr allocation outside the auto startup function
into tpm_chip_register. This ensures that allocated banks are initialized
in any case.
Fixes: 879b589210a9 ("tpm: retrieve digest size of unknown algorithms with PCR read")
Reported-by: Michal Suchanek <msuchanek@suse.de>
Signed-off-by: Nayna Jain <nayna@linux.ibm.com>
Reviewed-by: Mimi Zohar <zohar@linux.ibm.com>
Tested-by: Sachin Sant <sachinp@linux.vnet.ibm.com>
Tested-by: Michal Suchánek <msuchanek@suse.de>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
If clk_enable is not defined and chip initialization
is canceled code hits null dereference.
Easily reproducible with vTPM init fail:
swtpm chardev --tpmstate dir=nonexistent_dir --tpm2 --vtpm-proxy
BUG: kernel NULL pointer dereference, address: 00000000
...
Call Trace:
tpm_chip_start+0x9d/0xa0 [tpm]
tpm_chip_register+0x10/0x1a0 [tpm]
vtpm_proxy_work+0x11/0x30 [tpm_vtpm_proxy]
process_one_work+0x214/0x5a0
worker_thread+0x134/0x3e0
? process_one_work+0x5a0/0x5a0
kthread+0xd4/0x100
? process_one_work+0x5a0/0x5a0
? kthread_park+0x90/0x90
ret_from_fork+0x19/0x24
Fixes: 719b7d81f204 ("tpm: introduce tpm_chip_start() and tpm_chip_stop()")
Cc: stable@vger.kernel.org # v5.1+
Signed-off-by: Milan Broz <gmazyland@gmail.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Some more powerpc fixes for 5.3:
- Wire up the new clone3 syscall.
- A fix for the PAPR SCM nvdimm driver, to fix a crash when firmware
gives us a device that's attached to a non-online NUMA node.
- A fix for a boot failure on 32-bit with KASAN enabled.
- Three fixes for implicit fall through warnings, some of which are
errors for us due to -Werror.
Thanks to: Aneesh Kumar K.V, Christophe Leroy, Kees Cook, Santosh
Sivaraj, Stephen Rothwell"
* tag 'powerpc-5.3-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/kasan: fix early boot failure on PPC32
drivers/macintosh/smu.c: Mark expected switch fall-through
powerpc/spe: Mark expected switch fall-throughs
powerpc/nvdimm: Pick nearby online node if the device node is not online
powerpc/kvm: Fall through switch case explicitly
powerpc: Wire up clone3 syscall
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"A set of driver fixes for the I2C subsystem"
* 'i2c/for-current-fixed' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: s3c2410: Mark expected switch fall-through
i2c: at91: fix clk_offset for sama5d2
i2c: at91: disable TXRDY interrupt after sending data
i2c: iproc: Fix i2c master read more than 63 bytes
eeprom: at24: make spd world-readable again
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
"A small bunch of fixes from the irqchip department:
- Fix a couple of UAF on error paths (RZA1, GICv3 ITS)
- Fix iMX GPCv2 trigger setting
- Add missing of_node_put() on error path in MBIGEN
- Add another bunch of /* fall-through */ to silence warnings"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/renesas-rza1: Fix an use-after-free in rza1_irqc_probe()
irqchip/irq-imx-gpcv2: Forward irq type to parent
irqchip/irq-mbigen: Add of_node_put() before return
irqchip/gic-v3-its: Free unused vpt_page when alloc vpe table fail
irqchip/gic-v3: Mark expected switch fall-through
|
|
Merge misc fixes from Andrew Morton:
"17 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
drivers/acpi/scan.c: document why we don't need the device_hotplug_lock
memremap: move from kernel/ to mm/
lib/test_meminit.c: use GFP_ATOMIC in RCU critical section
asm-generic: fix -Wtype-limits compiler warnings
cgroup: kselftest: relax fs_spec checks
mm/memory_hotplug.c: remove unneeded return for void function
mm/migrate.c: initialize pud_entry in migrate_vma()
coredump: split pipe command whitespace before expanding template
page flags: prioritize kasan bits over last-cpuid
ubsan: build ubsan.c more conservatively
kasan: remove clang version check for KASAN_STACK
mm: compaction: avoid 100% CPU usage during compaction when a task is killed
mm: migrate: fix reference check race between __find_get_block() and migration
mm: vmscan: check if mem cgroup is disabled or not before calling memcg slab shrinker
ocfs2: remove set but not used variable 'last_hash'
Revert "kmemleak: allow to coexist with fault injection"
kernel/signal.c: fix a kernel-doc markup
|
|
Let's document why the lock is not needed in acpi_scan_init(), right now
this is not really obvious.
[akpm@linux-foundation.org: fix tpyo]
Link: http://lkml.kernel.org/r/20190731135306.31524-1-david@redhat.com
Signed-off-by: David Hildenbrand <david@redhat.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Oscar Salvador <osalvador@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
