| Age | Commit message (Collapse) | Author |
|---|
|
ConnectX HCA supports shrinking WQEs, so that a single work request
can be made of multiple units of wqe_shift. This way, WRs can differ
in size, and do not have to be a power of 2 in size, saving memory and
speeding up send WR posting. Unfortunately, if we do this then the
wqe_index field in CQEs can't be used to look up the WR ID anymore, so
our implementation does this only if selective signaling is off.
Further, on 32-bit platforms, we can't use vmap() to make the QP
buffer virtually contigious. Thus we have to use constant-sized WRs to
make sure a WR is always fully within a single page-sized chunk.
Finally, we use WRs with the NOP opcode to avoid wrapping around the
queue buffer in the middle of posting a WR, and we set the
NoErrorCompletion bit to avoid getting completions with error for NOP
WRs. However, NEC is only supported starting with firmware 2.2.232,
so we use constant-sized WRs for older firmware. And, since MLX QPs
only support SEND, we use constant-sized WRs in this case.
When stamping during NOP posting, do stamping following setting of the
NOP WQE valid bit.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Now that struct mlx4_buf.u is a struct instead of a union because of
the vmap() changes, there's no point in having a struct at all. So
move .direct and .page_list directly into struct mlx4_buf and get rid
of a bunch of unnecessary ".u"s.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
Since kernel virtual memory is not a problem on 64-bit systems, there
is no reason to use our own 2-layer page mapping scheme for large
kernel queue buffers on such systems. Instead, map the page list to a
single virtually contiguous buffer with vmap(), so that can we access
buffer memory via direct indexing.
Signed-off-by: Michael S. Tsirkin <mst@dev.mellanox.co.il>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
We use struct mlx4_buf for kernel QP, CQ and SRQ buffers, and the code
to look up an entry is duplicated in get_cqe_from_buf() and the QP and
SRQ versions of get_wqe(). Factor this out into mlx4_buf_offset().
This will also make it easier to switch over to using vmap() for buffers.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
|
|
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
[S390] dcss: Initialize workqueue before using it.
[S390] Remove BUILD_BUG_ON() in vmem code.
[S390] sclp_tty/sclp_vt220: Fix scheduling while atomic
[S390] dasd: fix panic caused by alias device offline
[S390] dasd: add ifcc handling
[S390] latencytop s390 support.
[S390] Implement ext2_find_next_bit.
[S390] Cleanup & optimize bitops.
[S390] Define GENERIC_LOCKBREAK.
[S390] console: allow vt220 console to be the only console
[S390] Fix couple of section mismatches.
[S390] Fix smp_call_function_mask semantics.
[S390] Fix linker script.
[S390] DEBUG_PAGEALLOC support for s390.
[S390] cio: Add shutdown callback for ccwgroup.
[S390] cio: Update documentation.
[S390] cio: Clean up chsc response code handling.
[S390] cio: make sense id procedure work with partial hardware response
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (21 commits)
[PKT_SCHED]: vlan tag match
[NET]: Add if_addrlabel.h to sanitized headers.
[NET] rtnetlink.c: remove no longer used functions
[ICMP]: Restore pskb_pull calls in receive function
[INET]: Fix accidentally broken inet(6)_hash_connect's port offset calculations.
[NET]: Remove further references to net-modules.txt
bluetooth rfcomm tty: destroy before tty_close()
bluetooth: blacklist another Broadcom BCM2035 device
drivers/bluetooth/btsdio.c: fix double-free
drivers/bluetooth/bpa10x.c: fix memleak
bluetooth: uninlining
bluetooth: hidp_process_hid_control remove unnecessary parameter dealing
tun: impossible to deassert IFF_ONE_QUEUE or IFF_NO_PI
hamradio: fix dmascc section mismatch
[SCTP]: Fix kernel panic while received AUTH chunk with BAD shared key identifier
[SCTP]: Fix kernel panic while received AUTH chunk while enabled auth
[IPV4]: Formatting fix for /proc/net/fib_trie.
[IPV6]: Fix sysctl compilation error.
[NET_SCHED]: Add #ifdef CONFIG_NET_EMATCH in net/sched/cls_flow.c (latest git broken build)
[IPV4]: Fix compile error building without CONFIG_FS_PROC
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/airlied/agp-2.6
* 'agp-patches' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/agp-2.6:
agp: remove flush_agp_mappings calls from new flush handling code
intel-agp: introduce IS_I915 and do some cleanups..
[intel_agp] fix name for G35 chipset
intel-agp: fixup resource handling in flush code.
intel-agp: add new chipset ID
agp: remove unnecessary pci_dev_put
agp: remove uid comparison as security check
fix AGP warning
agp/intel: Add chipset flushing support for i8xx chipsets.
intel-agp: add chipset flushing support
agp: add chipset flushing support to AGP interface
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
RDMA/nes: Add a driver for NetEffect RNICs
IB/mthca: Return proper error codes from mthca_fmr_alloc()
IB: Avoid marking __devinitdata as const
IB/mlx4: Actually print out the driver version
IB/ib_mthca: Pre-link receive WQEs in Tavor mode
IB/mthca: Remove checks for srq->first_free < 0
IB/fmr_pool: Allocate page list for pool FMRs only when caching enabled
IB/srp: Retry stale connections
mlx4_core: Don't read reserved fields in mlx4_QUERY_ADAPTER()
IB/mthca: Don't read reserved fields in mthca_QUERY_ADAPTER()
IPoIB: Remove a misleading debug print
IPoIB: Handle bonding failover race for connected neighbours too
IB/mthca: Fix and simplify page size calculation in mthca_reg_phys_mr()
IB/ehca: Add PMA support
IB/ehca: Update sma_attr also in case of disruptive config change
IB/ehca: Prevent sending UD packets to QP0
IB/cm: Add interim support for routed paths
mlx4_core: Fix more section mismatches
|
|
Corrects a mistake I made in a comment.
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
nubus: kill drivers/nubus/nubus_syms.c
EXPORT_SYMBOL's belong to the actual code.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
[Geert: eliminate NUMNAMES, as suggested by Richard Knutsson ]
[akpm@linux-foundation.org: coding-syle fixes]
Signed-off-by: Alejandro Martinez Ruiz <alex@flawedcode.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Richard Knutsson <ricknu-0@student.ltu.se>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Modify the b43 driver to avoid deadlocking suspend and resume, which happens
as a result of attempting to unregister device objects locked by the PM core
during suspend/resume cycles. Also, make it use a suspend-safe method of
unregistering device object in the resume error path.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Michael Buesch <mb@bu3sch.de>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Len Brown <lenb@kernel.org>
Cc: Greg KH <greg@kroah.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Make it possible to unregister a led classdev object in a safe way during a
suspend/resume cycle.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Michael Buesch <mb@bu3sch.de>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Len Brown <lenb@kernel.org>
Cc: Greg KH <greg@kroah.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Make it possible to unregister a Hardware Random Number Generator
device object in a safe way during a suspend/resume cycle.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Michael Buesch <mb@bu3sch.de>
Cc: Michael Buesch <mb@bu3sch.de>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Len Brown <lenb@kernel.org>
Cc: Greg KH <greg@kroah.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Make it possible to unregister a misc device object in a safe way during a
suspend/resume cycle.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Michael Buesch <mb@bu3sch.de>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Len Brown <lenb@kernel.org>
Cc: Greg KH <greg@kroah.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Replace latency.c use with pm_qos_params use.
Signed-off-by: mark gross <mgross@linux.intel.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Jaroslav Kysela <perex@suse.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The following patch is a generalization of the latency.c implementation done
by Arjan last year. It provides infrastructure for more than one parameter,
and exposes a user mode interface for processes to register pm_qos
expectations of processes.
This interface provides a kernel and user mode interface for registering
performance expectations by drivers, subsystems and user space applications on
one of the parameters.
Currently we have {cpu_dma_latency, network_latency, network_throughput} as
the initial set of pm_qos parameters.
The infrastructure exposes multiple misc device nodes one per implemented
parameter. The set of parameters implement is defined by pm_qos_power_init()
and pm_qos_params.h. This is done because having the available parameters
being runtime configurable or changeable from a driver was seen as too easy to
abuse.
For each parameter a list of performance requirements is maintained along with
an aggregated target value. The aggregated target value is updated with
changes to the requirement list or elements of the list. Typically the
aggregated target value is simply the max or min of the requirement values
held in the parameter list elements.
>From kernel mode the use of this interface is simple:
pm_qos_add_requirement(param_id, name, target_value):
Will insert a named element in the list for that identified PM_QOS
parameter with the target value. Upon change to this list the new target is
recomputed and any registered notifiers are called only if the target value
is now different.
pm_qos_update_requirement(param_id, name, new_target_value):
Will search the list identified by the param_id for the named list element
and then update its target value, calling the notification tree if the
aggregated target is changed. with that name is already registered.
pm_qos_remove_requirement(param_id, name):
Will search the identified list for the named element and remove it, after
removal it will update the aggregate target and call the notification tree
if the target was changed as a result of removing the named requirement.
>From user mode:
Only processes can register a pm_qos requirement. To provide for
automatic cleanup for process the interface requires the process to register
its parameter requirements in the following way:
To register the default pm_qos target for the specific parameter, the
process must open one of /dev/[cpu_dma_latency, network_latency,
network_throughput]
As long as the device node is held open that process has a registered
requirement on the parameter. The name of the requirement is
"process_<PID>" derived from the current->pid from within the open system
call.
To change the requested target value the process needs to write a s32
value to the open device node. This translates to a
pm_qos_update_requirement call.
To remove the user mode request for a target value simply close the device
node.
[akpm@linux-foundation.org: fix warnings]
[akpm@linux-foundation.org: fix build]
[akpm@linux-foundation.org: fix build again]
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: mark gross <mgross@linux.intel.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: Len Brown <lenb@kernel.org>
Cc: Jaroslav Kysela <perex@suse.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Venki Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Adam Belay <abelay@novell.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Convert AGP alpha driver from nopage to fault.
NULL is NOPAGE_SIGBUS, so we aren't changing behaviour there.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Use ARRAY_SIZE macroto get maximum ports in ColdFire serial driver.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Checking if an address is a vmalloc address is done in a couple of places.
Define a common version in mm.h and replace the other checks.
Again the include structures suck. The definition of VMALLOC_START and
VMALLOC_END is not available in vmalloc.h since highmem.c cannot be included
there.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Use drivers/gpio/pca9539.c instead.
Signed-off-by: eric miao <eric.miao@marvell.com>
Acked-by: Ben Gardner <bgardner@wabtec.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Philipp Zabel <philipp.zabel@gmail.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This adds a new-style I2C driver with basic support for the sixteen bit
PCA9539 GPIO expanders. These chips have multiple registers, push-pull output
drivers, and (not supported in this patch) pin change interrupts.
Board-specific code must provide "pca9539_platform_data" with each chip's
"i2c_board_info". That provides the GPIO numbers to be used by that chip, and
callbacks for board-specific setup/teardown logic.
Derived from drivers/i2c/chips/pca9539.c (which has no current known users).
This is faster and simpler; it uses 16-bit register access, and cache the
OUTPUT and DIRECTION registers for fast access
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Philipp Zabel <philipp.zabel@gmail.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ben Gardner <bgardner@wabtec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Basic driver for 8-bit SPI based MCP23S08 GPIO expander, without support for
IRQs or the shared chipselect mechanism.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Eric Miao <eric.miao@marvell.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Philipp Zabel <philipp.zabel@gmail.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ben Gardner <bgardner@wabtec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This is a new-style I2C driver for most common 8 and 16 bit I2C based
"quasi-bidirectional" GPIO expanders: pcf8574 or pcf8575, and several
compatible models (mostly faster, supporting I2C at up to 1 MHz).
The driver exposes the GPIO signals using the platform-neutral GPIO
programming interface, so they are easily accessed by other kernel code. The
lack of such a flexible kernel API has been a big factor in the proliferation
of board-specific drivers for these chips... stuff that rarely makes it
upstream since it's so ugly. This driver will let such boards use standard
calls.
Since it's a new-style driver, these devices must be configured as part of
board-specific init. That eliminates the need for error-prone manual
configuration of module parameters, and makes compatibility with legacy
drivers (pcf8574.c, pc8575.c) for these chips easier (there's a clear
either/or disjunction).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Cc: Eric Miao <eric.miao@marvell.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Philipp Zabel <philipp.zabel@gmail.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ben Gardner <bgardner@wabtec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Provide new implementation infrastructure that platforms may choose to use
when implementing the GPIO programming interface. Platforms can update their
GPIO support to use this. In many cases the incremental cost to access a
non-inlined GPIO should be less than a dozen instructions, with the memory
cost being about a page (total) of extra data and code. The upside is:
* Providing two features which were "want to have (but OK to defer)" when
GPIO interfaces were first discussed in November 2006:
- A "struct gpio_chip" to plug in GPIOs that aren't directly supported
by SOC platforms, but come from FPGAs or other multifunction devices
using conventional device registers (like UCB-1x00 or SM501 GPIOs,
and southbridges in PCs with more open specs than usual).
- Full support for message-based GPIO expanders, where registers are
accessed through sleeping I/O calls. Previous support for these
"cansleep" calls was just stubs. (One example: the widely used
pcf8574 I2C chips, with 8 GPIOs each.)
* Including a non-stub implementation of the gpio_{request,free}() calls,
making those calls much more useful. The diagnostic labels are also
recorded given DEBUG_FS, so /sys/kernel/debug/gpio can show a snapshot
of all GPIOs known to this infrastructure.
The driver programming interfaces introduced in 2.6.21 do not change at all;
this infrastructure is entirely below those covers.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Eric Miao <eric.miao@marvell.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Philipp Zabel <philipp.zabel@gmail.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ben Gardner <bgardner@wabtec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add an empty drivers/gpio directory for gpiolib infrastructure and GPIO
expanders. It will be populated by later patches.
This won't be the only place to hold such gpio_chip code. Many external chips
add a few GPIOs as secondary functionality (such as MFD drivers) and platform
code frequently needs to closely integrate GPIO and IRQ support.
This is placed *early* in the build/link sequence since it's common for other
drivers to depend on GPIOs to do their work, so they must be initialized early
in the device_initcall() sequence.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Cc: Eric Miao <eric.miao@marvell.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Philipp Zabel <philipp.zabel@gmail.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ben Gardner <bgardner@wabtec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This is a one-line patch to add the following to __scsi_alloc_queue():
dma_set_seg_boundary(dev, shost->dma_boundary);
This is the simplest approach but the result looks odd,
__scsi_alloc_queue() does:
blk_queue_segment_boundary(q, shost->dma_boundary);
dma_set_seg_boundary(dev, shost->dma_boundary);
blk_queue_max_segment_size(q, dma_get_max_seg_size(dev));
I think that it would be better to set up segment boundary in the same
way as we did for the maximum segment size. That is, removing
shost->dma_boundary and LLDs call pci_set_dma_seg_boundary (or its
friends).
Then __scsi_alloc_queue() can set up both limits in the same way:
blk_queue_segment_boundary(q, dma_get_seg_boundary(dev));
blk_queue_max_segment_size(q, dma_get_max_seg_size(dev));
killing dma_boundary in scsi_host_template needs a large patch for
libata (dma_boundary is used by only libata and sym53c8xx). I'll send
a patch to do that if it is acceptable. James and Jeff?
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Greg KH <greg@kroah.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This adds PCI's accessor for segment_boundary_mask in device_dma_parameters.
The default segment_boundary is set to 0xffffffff, same to the block layer's
default value (and the scsi mid layer uses the same value).
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Greg KH <greg@kroah.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This sets the segment size limit properly via pci_set_dma_max_seg_size
and remove blk_queue_max_segment_size because scsi-ml calls it.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Acked-by: "Salyzyn, Mark" <mark_salyzyn@adaptec.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This sets the segment size limit properly via pci_set_dma_max_seg_size
and remove blk_queue_max_segment_size because scsi-ml calls it.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
request_queue and device struct must have the same value of a segment
size limit. This patch adds blk_queue_segment_boundary in
__scsi_alloc_queue so LLDs don't need to call both
blk_queue_segment_boundary and set_dma_max_seg_size. A LLD can change
the default value (64KB) can call device_dma_parameters accessors like
pci_set_dma_max_seg_size when allocating scsi_host.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Jeff Garzik <jeff@garzik.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch makes iommu respect segment size limits when merging sg
lists.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Acked-by: Grant Grundler <grundler@parisc-linux.org>
Cc: Matthew Wilcox <willy@debian.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This adds struct device_dma_parameters in struct pci_dev and properly
sets up a pointer in struct device.
The default max_segment_size is set to 64K, same to the block layer's
default value.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Mostly-acked-by: Jeff Garzik <jeff@garzik.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The clock to generate the desired baudrate with the MPSC is first divided
by the Baud Rate Generator (BRG) and then by the MPSC itself. So, when the
BRG divider is changed, the MPSC divider must also be changed to generate
the correct baudrate. During MPSC initialization, the BRG divider is
changed but the MPSC divider isn't changed until much later. This results
in some printk's coming out garbled. To fix that, set the MPSC divider at
the same time that the BRG divider is changed.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Coding style tweaks and printk levels.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Invalid speeds are forced to 9600. Update the code for this to encode new
style baud rates properly.
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Some ports seem to be unable to drain their transmitters on shut down. Such a
problem can occur if the port is programmed for hardware imposed flow control,
characters are in the FIFO but the CTS signal is inactive.
Normally, this isn't a problem because most places where we wait for the
transmitter to drain have a time-out. However, there is no timeout in the
suspend path.
Give a port 30ms to drain; this is an arbitary value chosen to avoid long
delays if there are many such ports in the system, while giving a reasonable
chance for a single port to drain. Should a port not drain within this
timeout, issue a warning.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When we boot, serial ports remain in low power mode until they're used either
by userspace or for the kernel console.
However, if you suspend the system, and then resume, all serial ports will be
taken out of low power mode. This is bad news for embedded devices where this
can mean higher power consumption.
Only bring a serial port out of low power mode if the port is being used as
the kernel console, or is in use by userspace.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Allow the private_data field to be specified in platform_data for the
standard 8250/16550 UART. This field is used by DW APB type UARTs and
without this patch it's only possible to set this field when registering
the port by hand. If private_data is not set then the driver will
potentially oops with a NULL pointer dereference.
Signed-off-by: Will Newton <will.newton@gmail.com>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add ADDI-DATA GmbH communication cards to 8250_pci driver. Supported cards
are:
APCI-7300, APCI-7420, APCI-7500, APCI-7800 APCI-7300-2, APCI-7420-2,
APCI-7500-2 APCI-7300-3, APCI-7420-3, APCI-7500-3, APCI-7800-3
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Krauth J. <krauth.julien@addi-data.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Remove dead config symbol.
Signed-off-by: Jiri Olsa <olsajiri@gmail.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ben Dooks <ben@fluff.org>
Cc: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
with reverting "x86, serial: convert legacy COM ports to platform devices",
we will have the serial console before the port is probled again.
uart_add_one_port==>uart_configure_port==>set_mcttrl(port, 0) will clear
the DTR setting by uart_set_options(). then I will lose my output from
serial console again.
So try to keep DTR in uart_configure_port()
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Andi Kleen <ak@suse.de>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
pci_get_slot does a pci_dev_get, so pci_dev_put needs to be called in an
error case.
An extract of the semantic match used to find the problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
type find1.T,T1,T2;
identifier find1.E;
statement find1.S;
expression x1,x2,x3;
expression find1.test;
int ret != 0;
@@
T E;
...
(
* E = pci_get_slot(...);
if (E == NULL) S
|
* if ((E = pci_get_slot(...)) == NULL)
S
)
... when != pci_dev_put(...,(T1)E,...)
when != if (E != NULL) { ... pci_dev_put(...,(T1)E,...); ...}
when != x1 = (T1)E
when != E = x3;
when any
if (test) {
... when != pci_dev_put(...,(T2)E,...)
when != if (E != NULL) { ... pci_dev_put(...,(T2)E,...); ...}
when != x2 = (T2)E
(
* return;
|
* return ret;
)
}
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
of_iomap calls ioremap, and so should be matched with an iounmap. At the
two error returns, the result of calling of_iomap is only stored in a local
variable, so these error paths need to call iounmap. Furthermore, this
function ultimately stores the result of of_iomap in an array that is local
to the file. These values should be iounmapped at some point. I have
added a corresponding call to iounmap at the end of the function
m8xx_remove.
The problem was found using the following semantic match.
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
type T,T1,T2;
identifier E;
statement S;
expression x1,x2,x3;
int ret;
@@
T E;
...
* E = of_iomap(...);
if (E == NULL) S
... when != iounmap(...,(T1)E,...)
when != if (E != NULL) { ... iounmap(...,(T1)E,...); ...}
when != x1 = (T1)E
when != E = x3;
when any
if (...) {
... when != iounmap(...,(T2)E,...)
when != if (E != NULL) { ... iounmap(...,(T2)E,...); ...}
when != x2 = (T2)E
(
* return;
|
* return ret;
)
}
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Vitaly Bordug <vitb@kernel.crashing.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Olof Johansson <olof@lixom.net>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Update the AT91 CF driver to use the generic GPIO calls instead of the
AT91-specific ones; and request exclusive use of those signals.
Minor tweaks to cleanup code paths: always in reverse order of how the
resources were allocated, with remove() matching the fault paths of
probe().
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fixing:
CHECK drivers/net/pcmcia/pcnet_cs.c
drivers/net/pcmcia/pcnet_cs.c:523:15: warning: symbol 'hw_info' shadows an earlier one
drivers/net/pcmcia/pcnet_cs.c:148:18: originally declared here
Signed-off-by: Richard Knutsson <ricknu-0@student.ltu.se>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fixing:
CHECK drivers/net/pcmcia/fmvj18x_cs.c
drivers/net/pcmcia/fmvj18x_cs.c:1205:6: warning: symbol 'i' shadows an earlier one
drivers/net/pcmcia/fmvj18x_cs.c:1179:9: originally declared here
Signed-off-by: Richard Knutsson <ricknu-0@student.ltu.se>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Use 'max(x,y)' instead of 'x < y ? y : x'.
Signed-off-by: Richard Knutsson <ricknu-0@student.ltu.se>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fixing:
CHECK drivers/net/pcmcia/axnet_cs.c
drivers/net/pcmcia/axnet_cs.c:994:5: warning: symbol 'ax_close' was not declared. Should it be static?
drivers/net/pcmcia/axnet_cs.c:1017:6: warning: symbol 'ei_tx_timeout' was not declared. Should it be static?
Signed-off-by: Richard Knutsson <ricknu-0@student.ltu.se>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fixing:
CHECK drivers/net/pcmcia/3c574_cs.c
drivers/net/pcmcia/3c574_cs.c:695:7: warning: symbol 'i' shadows an earlier one
drivers/net/pcmcia/3c574_cs.c:636:6: originally declared here
Signed-off-by: Richard Knutson <ricknu-0@student.ltu.se>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
