| Age | Commit message (Collapse) | Author |
|---|
|
The IBM virtual ethernet driver's polling function continues
to process frames after rescheduling NAPI, resulting in a warning
if it exhausted its budget. Do not restart polling after calling
napi_reschedule. Instead let frames be processed in the following
instance.
Signed-off-by: Thomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ax88772_bind() should return error code immediately when the PHY
was not reset properly through ax88772a_hw_reset().
Otherwise, The asix_get_phyid() will block when get the PHY
Identifier from the PHYSID1 MII registers through asix_mdio_read()
due to the PHY isn't ready. Furthermore, it will produce a lot of
error message cause system crash.As follows:
asix 1-1:1.0 (unnamed net_device) (uninitialized): Failed to write
reg index 0x0000: -71
asix 1-1:1.0 (unnamed net_device) (uninitialized): Failed to send
software reset: ffffffb9
asix 1-1:1.0 (unnamed net_device) (uninitialized): Failed to write
reg index 0x0000: -71
asix 1-1:1.0 (unnamed net_device) (uninitialized): Failed to enable
software MII access
asix 1-1:1.0 (unnamed net_device) (uninitialized): Failed to read
reg index 0x0000: -71
asix 1-1:1.0 (unnamed net_device) (uninitialized): Failed to write
reg index 0x0000: -71
asix 1-1:1.0 (unnamed net_device) (uninitialized): Failed to enable
software MII access
asix 1-1:1.0 (unnamed net_device) (uninitialized): Failed to read
reg index 0x0000: -71
...
Signed-off-by: Zhang Run <zhang.run@zte.com.cn>
Reviewed-by: Yang Wei <yang.wei9@zte.com.cn>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux
Sasha Levin says:
====================
Hyper-V hv_netvsc commits for 5.0
Three patches from Haiyang Zhang to fix settings hash key using ethtool,
and Adrian Vladu's first patch fixing a few spelling mistakes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2019-01-22
this is a pull request of 4 patches for net/master.
The first patch by is by Manfred Schlaegl and reverts a patch that caused wrong
warning messages in certain use cases. The next patch is by Oliver Hartkopp for
the bcm that adds sanity checks for the timer value before using it to detect
potential interger overflows. The last two patches are for the flexcan driver,
YueHaibing's patch fixes the the return value in the error path of the
flexcan_setup_stop_mode() function. The second patch is by Uwe Kleine-König and
fixes a NULL pointer deref on older flexcan cores in flexcan_chip_start().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Procedure mlx4_init_user_cqes() handles returns by copy_to_user
incorrectly. copy_to_user() returns the number of bytes not copied.
Thus, a non-zero return should be treated as a -EFAULT error
(as is done elsewhere in the kernel). However, mlx4_init_user_cqes()
error handling simply returns the number of bytes not copied
(instead of -EFAULT).
Note, though, that this is a harmless bug: procedure mlx4_alloc_cq()
(which is the only caller of mlx4_init_user_cqes()) treats any
non-zero return as an error, but that returned error value is processed
internally, and not passed further up the call stack.
In addition, fixes the following sparse warning:
warning: incorrect type in argument 1 (different address spaces)
expected void [noderef] <asn:1>*to
got void *buf
Fixes: e45678973dcb ("{net, IB}/mlx4: Initialize CQ buffers in the driver when possible")
Reported by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Driver reads the query HCA capabilities without the corresponding masks.
Without the correct masks, the base addresses of the queues are
unaligned. In addition some reserved bits were wrongly read. Using the
correct masks, ensures alignment of the base addresses and allows future
firmware versions safe use of the reserved bits.
Fixes: ab9c17a009ee ("mlx4_core: Modify driver initialization flow to accommodate SRIOV for Ethernet")
Fixes: 0ff1fb654bec ("{NET, IB}/mlx4: Add device managed flow steering firmware API")
Signed-off-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use a bitmap to keep track of which partition types we've already seen;
for duplicates, return -EEXIST from efx_ef10_mtd_probe_partition() and
thus skip adding that partition.
Duplicate partitions occur because of the A/B backup scheme used by newer
sfc NICs. Prior to this patch they cause sysfs_warn_dup errors because
they have the same name, causing us not to expose any MTDs at all.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix all typos from hyperv netvsc code comments.
Signed-off-by: Adrian Vladu <avladu@cloudbasesolutions.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: Sasha Levin <sashal@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: "Alessandro Pilotti" <apilotti@cloudbasesolutions.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
Changing mtu, channels, or buffer sizes ops call to netvsc_attach(),
rndis_set_subchannel(), which always reset the hash key to default
value. That will override hash key changed previously. This patch
fixes the problem by save the hash key, then restore it when we re-
add the netvsc device.
Fixes: ff4a44199012 ("netvsc: allow get/set of RSS indirection table")
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
[sl: fix up subject line]
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
These assignments occur in multiple places. The patch refactor them
to a function for simplicity. It also puts the struct to heap area
for future expension.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
[sl: fix up subject line]
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
Hyper-V hosts require us to disable RSS before changing RSS key,
otherwise the changing request will fail. This patch fixes the
coding error.
Fixes: ff4a44199012 ("netvsc: allow get/set of RSS indirection table")
Reported-by: Wei Hu <weh@microsoft.com>
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
[sl: fix up subject line]
Signed-off-by: Sasha Levin <sashal@kernel.org>
|
|
EtherAVB may provide a checksum of packet data appended to packet data. In
order to allow this checksum to be received by the host descriptor data
needs to be enlarged by 2 bytes to accommodate the checksum.
In the case of MTU-sized packets without a VLAN tag the
checksum were already accommodated by virtue of the space reserved for the
VLAN tag. However, a packet of MTU-size with a VLAN tag consumed all
packet data space provided by a descriptor leaving no space for the
trailing checksum.
This was not detected by the driver which incorrectly used the last two
bytes of packet data as the checksum and truncate the packet by two bytes.
This resulted all such packets being dropped.
A work around is to disable RX checksum offload
# ethtool -K eth0 rx off
This patch resolves this problem by increasing the size available for
packet data in RX descriptors by two bytes.
Tested on R-Car E3 (r8a77990) ES1.0 based Ebisu-4D board
v2
* Use sizeof(__sum16) directly rather than adding a driver-local
#define for the size of the checksum provided by the hw (2 bytes).
Fixes: 4d86d3818627 ("ravb: RX checksum offload")
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A few PHY drivers have the GPLv2+ license text. They then either have
a MODULE_LICENSE() of GPLv2 only, or an SPDX tag of GPLv2 only.
Since the license text is much easier to understand than either the
SPDX tag or the MODULE_LICENSE, use it as the definitive source of the
licence, and fixup the others when there are contradictions.
Cc: David Wu <david.wu@rock-chips.com>
Cc: Dongpo Li <lidongpo@hisilicon.com>
Cc: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
According to the device tree binding the phy-supply property is
optional. Use the regulator_get_optional API accordingly. The
code already handles NULL just fine.
This gets rid of the following warning:
fec 2188000.ethernet: 2188000.ethernet supply phy not found, using dummy regulator
Signed-off-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The connect_local_phy should return NULL (not negative errno) on
error, since its caller expects it.
Signed-off-by: Atsushi Nemoto <atsushi.nemoto@sord.co.jp>
Acked-by: Thor Thayer <thor.thayer@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Converted to use "imply" instead of "select" for PTP_1588_CLOCK
driver selecting. This could break the hard dependency between
the PTP clock subsystem and ethernet drivers.
This patch also set "default y" for dpaa2 ptp driver building to
provide user an available ptp clock in default.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the error recovery process in the qede driver.
The process includes a partial/customized driver unload and load, which
allows it to look like a short suspend period to the kernel while
preserving the net devices' state.
Signed-off-by: Tomer Tayar <tomer.tayar@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the detection and handling of a parity error ("process kill
event"), including the update of the protocol drivers, and the prevention
of any HW access that will lead to device access towards the host while
recovery is in progress.
It also provides the means for the protocol drivers to trigger a recovery
process on their decision.
Signed-off-by: Tomer Tayar <tomer.tayar@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Initiating final cleanup after an ungraceful driver unload can lead to bad
PCI accesses towards the host.
This patch revises the load sequence so final cleanup is sent while the
internal master enable is cleared, to prevent the host accesses, and clears
the internal error indications just before enabling the internal master
enable.
Signed-off-by: Tomer Tayar <tomer.tayar@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The recent addition of SPDX license identifiers to the files in
drivers/net/ethernet/sun created a licensing conflict.
The cassini driver files contain a proper license notice:
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of the
* License, or (at your option) any later version.
but the SPDX change added:
SPDX-License-Identifier: GPL-2.0
So the file got tagged GPL v2 only while in fact it is licensed under GPL
v2 or later.
It's nice that people care about the SPDX tags, but they need to be more
careful about it. Not everything under (the) sun belongs to ...
Fix up the SPDX identifier and remove the boiler plate text as it is
redundant.
Fixes: c861ef83d771 ("sun: Add SPDX license tags to Sun network drivers")
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Shannon Nelson <shannon.nelson@oracle.com>
Cc: Zhu Yanjun <yanjun.zhu@oracle.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Cc: stable@vger.kernel.org
Acked-by: Shannon Nelson <shannon.lee.nelson@gmail.com>
Reviewed-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit cbffaf7aa09e ("can: flexcan: Always use last mailbox for TX")
introduced a loop letting i run up to (including) ARRAY_SIZE(regs->mb)
and in the body accessed regs->mb[i] which is an out-of-bounds array
access that then resulted in an access to an reserved register area.
Later this was changed by commit 0517961ccdf1 ("can: flexcan: Add
provision for variable payload size") to iterate a bit differently but
still runs one iteration too much resulting to call
flexcan_get_mb(priv, priv->mb_count)
which results in a WARN_ON and then a NULL pointer exception. This
only affects devices compatible with "fsl,p1010-flexcan",
"fsl,imx53-flexcan", "fsl,imx35-flexcan", "fsl,imx25-flexcan",
"fsl,imx28-flexcan", so newer i.MX SoCs are not affected.
Fixes: cbffaf7aa09e ("can: flexcan: Always use last mailbox for TX")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: linux-stable <stable@vger.kernel.org> # >= 4.20
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Fix a static code checker warning:
drivers/net/can/flexcan.c:1435 flexcan_setup_stop_mode() warn: passing zero to 'PTR_ERR'
Fixes: de3578c198c6 ("can: flexcan: add self wakeup support")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
removing it
This patch revert commit 7da11ba5c506
("can: dev: __can_get_echo_skb(): print error message, if trying to echo non existing skb")
After introduction of this change we encountered following new error
message on various i.MX plattforms (flexcan):
| flexcan 53fc8000.can can0: __can_get_echo_skb: BUG! Trying to echo non
| existing skb: can_priv::echo_skb[0]
The introduction of the message was a mistake because
priv->echo_skb[idx] = NULL is a perfectly valid in following case: If
CAN_RAW_LOOPBACK is disabled (setsockopt) in applications, the pkt_type
of the tx skb's given to can_put_echo_skb is set to PACKET_LOOPBACK. In
this case can_put_echo_skb will not set priv->echo_skb[idx]. It is
therefore kept NULL.
As additional argument for revert: The order of check and usage of idx
was changed. idx is used to access an array element before checking it's
boundaries.
Signed-off-by: Manfred Schlaegl <manfred.schlaegl@ginzinger.com>
Fixes: 7da11ba5c506 ("can: dev: __can_get_echo_skb(): print error message, if trying to echo non existing skb")
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Pull networking fixes from David Miller:
1) Fix endless loop in nf_tables, from Phil Sutter.
2) Fix cross namespace ip6_gre tunnel hash list corruption, from
Olivier Matz.
3) Don't be too strict in phy_start_aneg() otherwise we might not allow
restarting auto negotiation. From Heiner Kallweit.
4) Fix various KMSAN uninitialized value cases in tipc, from Ying Xue.
5) Memory leak in act_tunnel_key, from Davide Caratti.
6) Handle chip errata of mv88e6390 PHY, from Andrew Lunn.
7) Remove linear SKB assumption in fou/fou6, from Eric Dumazet.
8) Missing udplite rehash callbacks, from Alexey Kodanev.
9) Log dirty pages properly in vhost, from Jason Wang.
10) Use consume_skb() in neigh_probe() as this is a normal free not a
drop, from Yang Wei. Likewise in macvlan_process_broadcast().
11) Missing device_del() in mdiobus_register() error paths, from Thomas
Petazzoni.
12) Fix checksum handling of short packets in mlx5, from Cong Wang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (96 commits)
bpf: in __bpf_redirect_no_mac pull mac only if present
virtio_net: bulk free tx skbs
net: phy: phy driver features are mandatory
isdn: avm: Fix string plus integer warning from Clang
net/mlx5e: Fix cb_ident duplicate in indirect block register
net/mlx5e: Fix wrong (zero) TX drop counter indication for representor
net/mlx5e: Fix wrong error code return on FEC query failure
net/mlx5e: Force CHECKSUM_UNNECESSARY for short ethernet frames
tools: bpftool: Cleanup license mess
bpf: fix inner map masking to prevent oob under speculation
bpf: pull in pkt_sched.h header for tooling to fix bpftool build
selftests: forwarding: Add a test case for externally learned FDB entries
selftests: mlxsw: Test FDB offload indication
mlxsw: spectrum_switchdev: Do not treat static FDB entries as sticky
net: bridge: Mark FDB entries that were added by user as such
mlxsw: spectrum_fid: Update dummy FID index
mlxsw: pci: Return error on PCI reset timeout
mlxsw: pci: Increase PCI SW reset timeout
mlxsw: pci: Ring CQ's doorbell before RDQ's
MAINTAINERS: update email addresses of liquidio driver maintainers
...
|
|
Pull virtio/vhost fixes and cleanups from Michael Tsirkin:
"Fixes and cleanups all over the place"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
vhost/scsi: Use copy_to_iter() to send control queue response
vhost: return EINVAL if iovecs size does not match the message size
virtio-balloon: tweak config_changed implementation
virtio: don't allocate vqs when names[i] = NULL
virtio_pci: use queue idx instead of array idx to set up the vq
virtio: document virtio_config_ops restrictions
virtio: fix virtio_config_ops description
|
|
Use napi_consume_skb() to get bulk free. Note that napi_consume_skb is
safe to call in a non-napi context as long as the napi_budget flag is
correct.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fixes from Dan Williams:
"A crash fix, a build warning fix, a miscellaneous small cleanups.
In case anyone is looking for them, there was a regression caught by
testing that caused two patches to be dropped from this update. Those
patches have been reworked and will soak for another week / re-target
5.0-rc4.
- Fix driver initialization crash due to the inability to report an
'error' state for a DIMM's security capability.
- Build warning fix for little-endian ARM64 builds
- Fix a potential race between the EDAC driver's usage of the NFIT
SMBIOS id for a DIMM and the driver shutdown path.
- A small collection of one-line benign cleanups for duplicate
variable assignments, a duplicate header include and a mis-typed
function argument"
* tag 'libnvdimm-fixes-5.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
libnvdimm/security: Fix nvdimm_security_state() state request selection
acpi/nfit: Remove duplicate set nd_set in acpi_nfit_init_interleave_set()
acpi/nfit: Fix race accessing memdev in nfit_get_smbios_id()
libnvdimm/dimm: Fix security capability detection for non-Intel NVDIMMs
nfit: Mark some functions as __maybe_unused
ACPI/nfit: delete the function to_acpi_nfit_desc
ACPI/nfit: delete the redundant header file
|
|
git://www.linux-watchdog.org/linux-watchdog
Pull watchdog fixes from Wim Van Sebroeck:
- mt7621_wdt/rt2880_wdt: Fix compilation problem
- tqmx86: Fix a couple IS_ERR() vs NULL bugs
* tag 'linux-watchdog-5.0-rc-fixes' of git://www.linux-watchdog.org/linux-watchdog:
watchdog: tqmx86: Fix a couple IS_ERR() vs NULL bugs
watchdog: mt7621_wdt/rt2880_wdt: Fix compilation problem
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"A set of 17 fixes. Most of these are minor or trivial.
The one fix that may be serious is the isci one: the bug can cause hba
parameters to be set from uninitialized memory. I don't think it's
exploitable, but you never know"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: cxgb4i: add wait_for_completion()
scsi: qla1280: set 64bit coherent mask
scsi: ufs: Fix geometry descriptor size
scsi: megaraid_sas: Retry reads of outbound_intr_status reg
scsi: qedi: Add ep_state for login completion on un-reachable targets
scsi: ufs: Fix system suspend status
scsi: qla2xxx: Use correct number of vectors for online CPUs
scsi: hisi_sas: Set protection parameters prior to adding SCSI host
scsi: tcmu: avoid cmd/qfull timers updated whenever a new cmd comes
scsi: isci: initialize shost fully before calling scsi_add_host()
scsi: lpfc: lpfc_sli: Mark expected switch fall-throughs
scsi: smartpqi_init: fix boolean expression in pqi_device_remove_start
scsi: core: Synchronize request queue PM status only on successful resume
scsi: pm80xx: reduce indentation
scsi: qla4xxx: check return code of qla4xxx_copy_from_fwddb_param
scsi: megaraid_sas: correct an info message
scsi: target/iscsi: fix error msg typo when create lio_qr_cache failed
scsi: sd: Fix cache_type_store()
|
|
Pull block fixes from Jens Axboe:
- block size setting fixes for loop/nbd (Jan Kara)
- md bio_alloc_mddev() cleanup (Marcos)
- Ensure we don't lose the REQ_INTEGRITY flag (Ming)
- Two NVMe fixes by way of Christoph:
- Fix NVMe IRQ calculation (Ming)
- Uninitialized variable in nvmet-tcp (Sagi)
- BFQ comment fix (Paolo)
- License cleanup for recently added blk-mq-debugfs-zoned (Thomas)
* tag 'for-linus-20190118' of git://git.kernel.dk/linux-block:
block: Cleanup license notice
nvme-pci: fix nvme_setup_irqs()
nvmet-tcp: fix uninitialized variable access
block: don't lose track of REQ_INTEGRITY flag
blockdev: Fix livelocks on loop device
nbd: Use set_blocksize() to set device blocksize
md: Make bio_alloc_mddev use bio_alloc_bioset
block, bfq: fix comments on __bfq_deactivate_entity
|
|
Since phy driver features became a link_mode bitmap, phy drivers that
don't have a list of features configured will cause the kernel to crash
when probed.
Prevent the phy driver from registering if the features field is missing.
Fixes: 719655a14971 ("net: phy: Replace phy driver features u32 with link_mode bitmap")
Reported-by: Scott Wood <oss@buserror.net>
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A recent commit in Clang expanded the -Wstring-plus-int warning, showing
some odd behavior in this file.
drivers/isdn/hardware/avm/b1.c:426:30: warning: adding 'int' to a string does not append to the string [-Wstring-plus-int]
cinfo->version[j] = "\0\0" + 1;
~~~~~~~^~~
drivers/isdn/hardware/avm/b1.c:426:30: note: use array indexing to silence this warning
cinfo->version[j] = "\0\0" + 1;
^
& [ ]
1 warning generated.
This is equivalent to just "\0". Nick pointed out that it is smarter to
use "" instead of "\0" because "" is used elsewhere in the kernel and
can be deduplicated at the linking stage.
Link: https://github.com/ClangBuiltLinux/linux/issues/309
Suggested-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2019-01-18
This series introduces some fixes to mlx5 driver.
Please pull and let me know if there is any problem.
For -stable v4.18
('net/mlx5e: Force CHECKSUM_UNNECESSARY for short ethernet frames')
The patch doesn't apply cleanly to 4.18.y, but it is very simple to
resolve, what should be the procedure here ?
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Previously the identifier used for indirect block callback registry
and for block rule cb registry (when done via indirect blocks) was the
pointer to the tunnel netdev we were interested in receiving updates on.
This worked fine if a single PF existed that registered one callback for
the tunnel netdev of interest. However, if multiple PFs are in place then
the 2nd PF tries to register with the same tunnel netdev identifier. This
leads to EEXIST errors and/or incorrect cb deletions.
Prevent this conflict by using the rpriv pointer as the identifier for
netdev indirect block cb registry, allowing each PF to register a unique
callback per tunnel netdev. For block cb registry, the same PF may
register multiple cbs to the same block if using TC shared blocks.
Instead of the rpriv, use the pointer to the allocated indr_priv data as
the identifier here. This means that there can be a unique block callback
for each PF/tunnel netdev combo.
Fixes: f5bc2c5de101 ("net/mlx5e: Support TC indirect block notifications
for eswitch uplink reprs")
Signed-off-by: Eli Britstein <elibr@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
For representors, the TX dropped counter is not folded from the
per-ring counters. Fix it.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Advertised and configured FEC query failure resulted in printing
wrong error code.
Fixes: 6cfa94605091 ("net/mlx5e: Ethtool driver callback for query/set FEC policy")
Signed-off-by: Shay Agroskin <shayag@mellanox.com>
Reported-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
When an ethernet frame is padded to meet the minimum ethernet frame
size, the padding octets are not covered by the hardware checksum.
Fortunately the padding octets are usually zero's, which don't affect
checksum. However, we have a switch which pads non-zero octets, this
causes kernel hardware checksum fault repeatedly.
Prior to:
commit '88078d98d1bb ("net: pskb_trim_rcsum() and CHECKSUM_COMPLETE ...")'
skb checksum was forced to be CHECKSUM_NONE when padding is detected.
After it, we need to keep skb->csum updated, like what we do for RXFCS.
However, fixing up CHECKSUM_COMPLETE requires to verify and parse IP
headers, it is not worthy the effort as the packets are so small that
CHECKSUM_COMPLETE can't save anything.
Fixes: 88078d98d1bb ("net: pskb_trim_rcsum() and CHECKSUM_COMPLETE are friends"),
Cc: Eric Dumazet <edumazet@google.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Cc: Nikola Ciprich <nikola.ciprich@linuxbox.cz>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The driver currently treats static FDB entries as both static and
sticky. This is incorrect and prevents such entries from being roamed to
a different port via learning.
Fix this by configuring static entries with ageing disabled and roaming
enabled.
In net-next we can add proper support for the newly introduced 'sticky'
flag.
Fixes: 56ade8fe3fe1 ("mlxsw: spectrum: Add initial support for Spectrum ASIC")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Alexander Petrovskiy <alexpe@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When using a tc flower action of egress mirred redirect, the driver adds
an implicit FID setting action. This implicit action sets a dummy FID to
the packet and is used as part of a design for trapping unmatched flows
in OVS. While this implicit FID setting action is supposed to be a NOP
when a redirect action is added, in Spectrum-2 the FID record is
consulted as the dummy FID index is an 802.1D FID index and the packet
is dropped instead of being redirected.
Set the dummy FID index value to be within 802.1Q range. This satisfies
both Spectrum-1 which ignores the FID and Spectrum-2 which identifies it
as an 802.1Q FID and will then follow the redirect action.
Fixes: c3ab435466d5 ("mlxsw: spectrum: Extend to support Spectrum-2 ASIC")
Signed-off-by: Nir Dotan <nird@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Return an appropriate error in the case when the driver timeouts on waiting
for firmware to go out of PCI reset.
Fixes: 233fa44bd67a ("mlxsw: pci: Implement reset done check")
Signed-off-by: Nir Dotan <nird@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Spectrum-2 PHY layer introduces a calibration period which is a part of the
Spectrum-2 firmware boot process. Hence increase the SW timeout waiting for
the firmware to come out of boot. This does not increase system boot time
in cases where the firmware PHY calibration process is done quickly.
Fixes: c3ab435466d5 ("mlxsw: spectrum: Extend to support Spectrum-2 ASIC")
Signed-off-by: Nir Dotan <nird@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a packet should be trapped to the CPU the device consumes a WQE
(work queue element) from an RDQ (receive descriptor queue) and copies
the packet to the address specified in the WQE. The device then tries to
post a CQE (completion queue element) that contains various metadata
(e.g., ingress port) about the packet to a CQ (completion queue).
In case the device managed to consume a WQE, but did not manage to post
the corresponding CQE, it will get stuck. This unlikely situation can be
triggered due to the scheme the driver is currently using to process
CQEs.
The driver will consume up to 512 CQEs at a time and after processing
each corresponding WQE it will ring the RDQ's doorbell, letting the
device know that a new WQE was posted for it to consume. Only after
processing all the CQEs (up to 512), the driver will ring the CQ's
doorbell, letting the device know that new ones can be posted.
Fix this by having the driver ring the CQ's doorbell for every processed
CQE, but before ringing the RDQ's doorbell. This guarantees that
whenever we post a new WQE, there is a corresponding CQE available. Copy
the currently processed CQE to prevent the device from overwriting it
with a new CQE after ringing the doorbell.
Note that the driver still arms the CQ only after processing all the
pending CQEs, so that interrupts for this CQ will only be delivered
after the driver finished its processing.
Before commit 8404f6f2e8ed ("mlxsw: pci: Allow to use CQEs of version 1
and version 2") the issue was virtually impossible to trigger since the
number of CQEs was twice the number of WQEs and the number of CQEs
processed at a time was equal to the number of available WQEs.
Fixes: 8404f6f2e8ed ("mlxsw: pci: Allow to use CQEs of version 1 and version 2")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Semion Lisyansky <semionl@mellanox.com>
Tested-by: Semion Lisyansky <semionl@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
"also enables" should not be spelled as one word.
Fixes: cfc80d9a1163 ("net: Introduce net_failover driver")
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In certain cases, pskb_trim_rcsum() may change skb pointers.
Reinitialize header pointers afterwards to avoid potential
use-after-frees. Add a note in the documentation of
pskb_trim_rcsum(). Found by KASAN.
Signed-off-by: Ross Lagerwall <ross.lagerwall@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
- a regression fix at v4l2 core, with affects multi-plane streams
- a fix at vim2m driver
* tag 'media/v5.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
media: vim2m: only cancel work if it is for right context
media: v4l: ioctl: Validate num_planes for debug messages
media: v4l: ioctl: Validate num_planes before using it
media: v4l2-ioctl: Clear only per-plane reserved fields
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas::
- Fix PCI kconfig menu organization (Rob Herring)
- Fix pci_alloc_irq_vectors_affinity() error return to allow "reduce
and retry" for drivers using IRQ sets (Ming Lei)
- Fix "pci=disable_acs_redir" initdata use-after-free problem (Logan
Gunthorpe)
* tag 'pci-v5.0-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: Fix __initdata issue with "pci=disable_acs_redir" parameter
PCI/MSI: Return -ENOSPC from pci_alloc_irq_vectors_affinity()
PCI: Fix PCI kconfig menu organization
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux
Pull i3c fixes from Boris Brezillon:
- Fix the error check on master->sysclk val in the Cadence driver
- Fix reattach implementation in the Designware driver
* tag 'i3c/fixes-for-5.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/i3c/linux:
i3c: master: dw-i3c-master: fix i3c_attach/reattach
i3c: master: Fix an error checking typo in 'cdns_i3c_master_probe()'
|
|
Pull mtd fixes from Boris Brezillon:
"Raw NAND changes:
- jz4740: fix a compilation warning
- fsmc: fix a regression introduced by ->select_chip() deprecation
- denali: fix a regression introduced by NAND_KEEP_TIMINGS addition"
* tag 'mtd/fixes-for-5.0-rc3' of git://git.infradead.org/linux-mtd:
mtd: rawnand: denali: get ->setup_data_interface() working again
mtd: nand: jz4740: fix '__iomem *' vs. '* __iomem'
mtd: rawnand: fsmc: Keep bank enable bit set
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap fixes from Mark Brown:
"The cleanups for the way we handle type information introduced during
the merge window revealed that we'd been abusing the irq APIs for a
long time, causing breakage for systems.
This has a couple of minimal fixes for that which restore the previous
behaviour for the time being, we'll fix it properly for v5.1 but
that'd be a bit much to do as a bug fix"
* tag 'regmap-fix-v5.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap-irq: do not write mask register if mask_base is zero
regmap: regmap-irq: silently ignore unsupported type settings
|
|
handling
The current code in __mdiobus_register() doesn't properly handle
failures returned by the devm_gpiod_get_optional() call: it returns
immediately, without unregistering the device that was added by the
call to device_register() earlier in the function.
This leaves a stale device, which then causes a NULL pointer
dereference in the code that handles deferred probing:
[ 1.489982] Unable to handle kernel NULL pointer dereference at virtual address 00000074
[ 1.498110] pgd = (ptrval)
[ 1.500838] [00000074] *pgd=00000000
[ 1.504432] Internal error: Oops: 17 [#1] SMP ARM
[ 1.509133] Modules linked in:
[ 1.512192] CPU: 1 PID: 51 Comm: kworker/1:3 Not tainted 4.20.0-00039-g3b73a4cc8b3e-dirty #99
[ 1.520708] Hardware name: Xilinx Zynq Platform
[ 1.525261] Workqueue: events deferred_probe_work_func
[ 1.530403] PC is at klist_next+0x10/0xfc
[ 1.534403] LR is at device_for_each_child+0x40/0x94
[ 1.539361] pc : [<c0683fbc>] lr : [<c0455d90>] psr: 200e0013
[ 1.545628] sp : ceeefe68 ip : 00000001 fp : ffffe000
[ 1.550863] r10: 00000000 r9 : c0c66790 r8 : 00000000
[ 1.556079] r7 : c0457d44 r6 : 00000000 r5 : ceeefe8c r4 : cfa2ec78
[ 1.562604] r3 : 00000064 r2 : c0457d44 r1 : ceeefe8c r0 : 00000064
[ 1.569129] Flags: nzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none
[ 1.576263] Control: 18c5387d Table: 0ed7804a DAC: 00000051
[ 1.582013] Process kworker/1:3 (pid: 51, stack limit = 0x(ptrval))
[ 1.588280] Stack: (0xceeefe68 to 0xceef0000)
[ 1.592630] fe60: cfa2ec78 c0c03c08 00000000 c0457d44 00000000 c0c66790
[ 1.600814] fe80: 00000000 c0455d90 ceeefeac 00000064 00000000 0d7a542e cee9d494 cfa2ec78
[ 1.608998] fea0: cfa2ec78 00000000 c0457d44 c0457d7c cee9d494 c0c03c08 00000000 c0455dac
[ 1.617182] fec0: cf98ba44 cf926a00 cee9d494 0d7a542e 00000000 cf935a10 cf935a10 cf935a10
[ 1.625366] fee0: c0c4e9b8 c0457d7c c0c4e80c 00000001 cf935a10 c0457df4 cf935a10 c0c4e99c
[ 1.633550] ff00: c0c4e99c c045a27c c0c4e9c4 ced63f80 cfde8a80 cfdebc00 00000000 c013893c
[ 1.641734] ff20: cfde8a80 cfde8a80 c07bd354 ced63f80 ced63f94 cfde8a80 00000008 c0c02d00
[ 1.649936] ff40: cfde8a98 cfde8a80 ffffe000 c0139a30 ffffe000 c0c6624a c07bd354 00000000
[ 1.658120] ff60: ffffe000 cee9e780 ceebfe00 00000000 ceeee000 ced63f80 c0139788 cf8cdea4
[ 1.666304] ff80: cee9e79c c013e598 00000001 ceebfe00 c013e44c 00000000 00000000 00000000
[ 1.674488] ffa0: 00000000 00000000 00000000 c01010e8 00000000 00000000 00000000 00000000
[ 1.682671] ffc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 1.690855] ffe0: 00000000 00000000 00000000 00000000 00000013 00000000 00000000 00000000
[ 1.699058] [<c0683fbc>] (klist_next) from [<c0455d90>] (device_for_each_child+0x40/0x94)
[ 1.707241] [<c0455d90>] (device_for_each_child) from [<c0457d7c>] (device_reorder_to_tail+0x38/0x88)
[ 1.716476] [<c0457d7c>] (device_reorder_to_tail) from [<c0455dac>] (device_for_each_child+0x5c/0x94)
[ 1.725692] [<c0455dac>] (device_for_each_child) from [<c0457d7c>] (device_reorder_to_tail+0x38/0x88)
[ 1.734927] [<c0457d7c>] (device_reorder_to_tail) from [<c0457df4>] (device_pm_move_to_tail+0x28/0x40)
[ 1.744235] [<c0457df4>] (device_pm_move_to_tail) from [<c045a27c>] (deferred_probe_work_func+0x58/0x8c)
[ 1.753746] [<c045a27c>] (deferred_probe_work_func) from [<c013893c>] (process_one_work+0x210/0x4fc)
[ 1.762888] [<c013893c>] (process_one_work) from [<c0139a30>] (worker_thread+0x2a8/0x5c0)
[ 1.771072] [<c0139a30>] (worker_thread) from [<c013e598>] (kthread+0x14c/0x154)
[ 1.778482] [<c013e598>] (kthread) from [<c01010e8>] (ret_from_fork+0x14/0x2c)
[ 1.785689] Exception stack(0xceeeffb0 to 0xceeefff8)
[ 1.790739] ffa0: 00000000 00000000 00000000 00000000
[ 1.798923] ffc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[ 1.807107] ffe0: 00000000 00000000 00000000 00000000 00000013 00000000
[ 1.813724] Code: e92d47f0 e1a05000 e8900048 e1a00003 (e5937010)
[ 1.819844] ---[ end trace 3c2c0c8b65399ec9 ]---
The actual error that we had from devm_gpiod_get_optional() was
-EPROBE_DEFER, due to the GPIO being provided by a driver that is
probed later than the Ethernet controller driver.
To fix this, we simply add the missing device_del() invocation in the
error path.
Fixes: 69226896ad636 ("mdio_bus: Issue GPIO RESET to PHYs")
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
