| Age | Commit message (Collapse) | Author |
|---|
|
A Davicom application note for the DM9000 network device recommends
performing software reset twice to correctly initialise the device.
Without this reset some devices fail to initialise correctly on
system startup.
Cc: David S. Miller <davem@davemloft.net>
Cc: Jingoo Han <jg1.han@samsung.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Michael Abbott <michael.abbott@diamond.ac.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Take the phy out of reset explicitly during system resume to avoid
losing network connectivity.
Cc: David S. Miller <davem@davemloft.net>
Cc: Jingoo Han <jg1.han@samsung.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some of the changes introduced in commit 6741f40 (DM9000B: driver
initialization upgrade) break functionality on DM9000A
(error message during NFS boot: "dm9000 dm9000.0: eth0: link down")
Since the changes were meant to serve only DM9000B, make them
dependent on the chip type.
Cc: David S. Miller <davem@davemloft.net>
Cc: Jingoo Han <jg1.han@samsung.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into char-misc-linus
Jonathan writes:
Third set of IIO fixes for the 3.12 cycle.
Two little ones this time:
1) A missing clk_unprepare in adf4350.
2) A missing free of the active_scan_mask when iio_disable_all_buffers is
called during an unexpected device removal. This leak was introduced by
the fix
a87c82e454f184a9473f8cdfd4d304205f585f65 iio: Stop sampling when the device is removed
and hence is a regression fix.
|
|
This reverts commit 90d33f3ec519db19d785216299a4ee85ef58ec97 as it's not
the correct fix for this issue, and it causes a build warning to be
added to the kernel tree.
Cc: K. Y. Srinivasan <kys@microsoft.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Two functions defined in device_pm.c, acpi_dev_pm_add_dependent()
and acpi_dev_pm_remove_dependent(), have no callers and may be
dropped, so drop them.
Moreover, they are the only functions adding entries to and removing
entries from the power_dependent list in struct acpi_device, so drop
that list too.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Previously, we wanted SCSI devices corrsponding to ATA devices to
be runtime resumed when the power resource for those ATA device was
turned on by some other device, so we added the SCSI device to the
dependent device list of the ATA device's ACPI node. However, this
code has no effect after commit 41863fc (ACPI / power: Drop automaitc
resume of power resource dependent devices) and the mechanism it was
supposed to implement is regarded as a bad idea now, so drop it.
[rjw: Changelog]
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
When inserting a wrong value to /sys/devices/system/memory/memoryX/state file,
following messages are shown. And device_hotplug_lock is never released.
================================================
[ BUG: lock held when returning to user space! ]
3.12.0-rc4-debug+ #3 Tainted: G W
------------------------------------------------
bash/6442 is leaving the kernel with locks still held!
1 lock held by bash/6442:
#0: (device_hotplug_lock){+.+.+.}, at: [<ffffffff8146cbb5>] lock_device_hotplug_sysfs+0x15/0x50
This issue was introdued by commit fa2be40 (drivers: base: use standard
device online/offline for state change).
This patch releases device_hotplug_lcok when store_mem_state returns EINVAL.
Signed-off-by: Yasuaki Ishimatsu <isimatu.yasuaki@jp.fujitsu.com>
Reviewed-by: Toshi Kani <toshi.kani@hp.com>
CC: Seth Jennings <sjenning@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device-mapper fix from Alasdair Kergon:
"A patch to avoid data corruption in a device-mapper snapshot.
This is primarily a data corruption bug that all users of
device-mapper snapshots will want to fix. The CVE is due to a data
leak under specific circumstances if, for example, the snapshot is
presented to a virtual machine: a block written as data inside the VM
can get interpreted incorrectly on the host outside the VM as
metadata, causing the host to provide the VM with access to blocks it
would not otherwise see. This is likely to affect few, if any,
people"
* tag 'dm-3.12-fix-cve' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm snapshot: fix data corruption
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull gpio fixes from Linus Walleij:
"Three GPIO fixes for the v3.12 series:
- A fix to the Lynxpoint IRQ handler
- Two late fixes to fallout from the gpiod refactoring"
* tag 'gpio-v3.12-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpiolib: let gpiod_request() return -EPROBE_DEFER
gpiolib: safer implementation of desc_to_gpio()
gpio/lynxpoint: check if the interrupt is enabled in IRQ handler
|
|
The index field of cpufreq_frequency_table has been renamed to
driver_data by commit 5070158 (cpufreq: rename index as driver_data
in cpufreq_frequency_table).
This patch updates the s3c64xx driver to match.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Cc: 3.11+ <stable@vger.kernel.org> # 3.11+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The mechanism causing devices depending on a given power resource
(that is, devices that can be in D0 only if that power resource is
on) to be resumed automatically when the power resource is turned
on (and their "inferred" power state becomes D0 as a result) is
inherently racy and in fact unnecessary.
It is racy, because if the power resource is turned on and then
immediately off, the device resume triggered by the first transition
to "on" may still happen, causing the power resource to be turned
on again. That again will trigger the "resume of dependent devices"
mechanism, but if the devices in question are not in use, they will
be suspended in the meantime causing the power resource to be turned
off. However, the "resume of dependent devices" will next resume
them again and so on. In some cases (USB port PM in particular) that
leads to an endless busy loop of flipping the resource on and off
continuously.
It is needless, because whoever turns a power resource on will most
likely turn it off at some point and the devices that go into "D0"
as a result of turning it on will then go back into D3cold
(generally, the state they were in before).
Moreover, turning on all power resources a device needs to go into
D0 is not sufficient for a full transition into D0 in general.
Namely, _PS0 may need to be executed in addition to that in some
cases. This means that the whole rationale of the "resume of
dependent devices" mechanism was incorrect to begin with and it's
best to remove it entirely.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The expression in line 398 of intel_pstate.c causes the following
warning to be emitted:
drivers/cpufreq/intel_pstate.c:398:3: warning: left shift count >= width of type
which happens because unsigned long is 32-bit on some architectures.
Fix that by using a helper u64 variable and simplify the code
slightly.
Tested-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Rescind of subchannels were not being correctly handled. Fix the bug.
Signed-off-by: K. Y. Srinivasan <kys@microsoft.com>
Cc: <stable@vger.kernel.org> [3.11+]
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The USB3503 driver had an incorrect depedency on REGMAP, instead of
REGMAP_I2C. This caused the build to fail since the necessary regmap
i2c pieces were not available.
Signed-off-by: Matthew Dawson <matthew@mjdsystems.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When CMA fails to initialize in v3.12-rc4, the chipidea driver oopses
the kernel while trying to remove and put the HCD which doesn't exist:
WARNING: CPU: 0 PID: 6 at /home/rmk/git/linux-rmk/arch/arm/mm/dma-mapping.c:511
__dma_alloc+0x200/0x240()
coherent pool not initialised!
Modules linked in:
CPU: 0 PID: 6 Comm: kworker/u2:0 Tainted: G W 3.12.0-rc4+ #56
Workqueue: deferwq deferred_probe_work_func
Backtrace:
[<c001218c>] (dump_backtrace+0x0/0x10c) from [<c0012328>] (show_stack+0x18/0x1c)
r6:c05fd9cc r5:000001ff r4:00000000 r3:df86ad00
[<c0012310>] (show_stack+0x0/0x1c) from [<c05f3a4c>] (dump_stack+0x70/0x8c)
[<c05f39dc>] (dump_stack+0x0/0x8c) from [<c00230a8>] (warn_slowpath_common+0x6c/0x8c)
r4:df883a60 r3:df86ad00
[<c002303c>] (warn_slowpath_common+0x0/0x8c) from [<c002316c>] (warn_slowpath_fmt+0x38/0x40)
r8:ffffffff r7:00001000 r6:c083b808 r5:00000000 r4:df2efe80
[<c0023134>] (warn_slowpath_fmt+0x0/0x40) from [<c00196bc>] (__dma_alloc+0x200/0x240)
r3:00000000 r2:c05fda00
[<c00194bc>] (__dma_alloc+0x0/0x240) from [<c001982c>] (arm_dma_alloc+0x88/0xa0)
[<c00197a4>] (arm_dma_alloc+0x0/0xa0) from [<c03e2904>] (ehci_setup+0x1f4/0x438)
[<c03e2710>] (ehci_setup+0x0/0x438) from [<c03cbd60>] (usb_add_hcd+0x18c/0x664)
[<c03cbbd4>] (usb_add_hcd+0x0/0x664) from [<c03e89f4>] (host_start+0xf0/0x180)
[<c03e8904>] (host_start+0x0/0x180) from [<c03e7c34>] (ci_hdrc_probe+0x360/0x670
)
r6:df2ef410 r5:00000000 r4:df2c3010 r3:c03e8904
[<c03e78d4>] (ci_hdrc_probe+0x0/0x670) from [<c0311044>] (platform_drv_probe+0x20/0x24)
[<c0311024>] (platform_drv_probe+0x0/0x24) from [<c030fcac>] (driver_probe_device+0x9c/0x234)
...
---[ end trace c88ccaf3969e8422 ]---
Unable to handle kernel NULL pointer dereference at virtual address 00000028
pgd = c0004000
[00000028] *pgd=00000000
Internal error: Oops: 17 [#1] SMP ARM
Modules linked in:
CPU: 0 PID: 6 Comm: kworker/u2:0 Tainted: G W 3.12.0-rc4+ #56
Workqueue: deferwq deferred_probe_work_func
task: df86ad00 ti: df882000 task.ti: df882000
PC is at usb_remove_hcd+0x10/0x150
LR is at host_stop+0x1c/0x3c
pc : [<c03cacec>] lr : [<c03e88e4>] psr: 60000013
sp : df883b50 ip : df883b78 fp : df883b74
r10: c11f4c54 r9 : c0836450 r8 : df30c400
r7 : fffffff4 r6 : df2ef410 r5 : 00000000 r4 : df2c3010
r3 : 00000000 r2 : 00000000 r1 : df86b0a0 r0 : 00000000
Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment kernel
Control: 10c53c7d Table: 2f29404a DAC: 00000015
Process kworker/u2:0 (pid: 6, stack limit = 0xdf882240)
Stack: (0xdf883b50 to 0xdf884000)
...
Backtrace:
[<c03cacdc>] (usb_remove_hcd+0x0/0x150) from [<c03e88e4>] (host_stop+0x1c/0x3c)
r6:df2ef410 r5:00000000 r4:df2c3010
[<c03e88c8>] (host_stop+0x0/0x3c) from [<c03e8aa0>] (ci_hdrc_host_destroy+0x1c/0x20)
r5:00000000 r4:df2c3010
[<c03e8a84>] (ci_hdrc_host_destroy+0x0/0x20) from [<c03e7c80>] (ci_hdrc_probe+0x3ac/0x670)
[<c03e78d4>] (ci_hdrc_probe+0x0/0x670) from [<c0311044>] (platform_drv_probe+0x20/0x24)
[<c0311024>] (platform_drv_probe+0x0/0x24) from [<c030fcac>] (driver_probe_device+0x9c/0x234)
[<c030fc10>] (driver_probe_device+0x0/0x234) from [<c030ff28>] (__device_attach+0x44/0x48)
...
---[ end trace c88ccaf3969e8423 ]---
Fix this so at least we can continue booting and get to a shell prompt.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Some USB drive enclosures do not correctly report an
overflow condition if they hold a drive with a capacity
over 2TB and are confronted with a READ_CAPACITY_10.
They answer with their capacity modulo 2TB.
The generic layer cannot cope with that. It must be told
to use READ_CAPACITY_16 from the beginning.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Interface 6 of this device speaks QMI as per tests done by us.
Credits go to Antonella for providing the hardware.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: Antonella Pellizzari <anto.pellizzari83@gmail.com>
Tested-by: Dan Williams <dcbw@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Due to missing braces on an if statement, in presence of a device_node a
port was always assigned -1, regardless of any alias entries in the
device tree. Conversely, if device_node was NULL, an unitialized port
ended up being used.
This patch adds the missing braces, fixing the issues.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Tony Prisk <linux@prisktech.co.nz>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The device descriptors are messed up after remote wakeup
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This fixes an oops caused by buslogic driver when initializing a BusLogic
MultiMaster adapter. Initialization code used scope of a variable
incorrectly which created a NULL pointer. Oops message is below:
BUG: unable to handle kernel NULL pointer dereference at 0000000c
IP: [<c150c137>] blogic_init_mm_probeinfo.isra.17+0x20a/0x583
*pde = 00000000
Oops: 002 [#1] PREEMPT SMP
Modules linked in:
CPU: 1 PID: 1 Comm: swapper/0 Not tainted 3.11.1.puz1 #1
Hardware name: /Canterwood, BIOS 6.00 PG 05/16/2003
task: f7050000 ti: f7054000 task.ti: f7054000
EIP: 0060:[<c150c137>] EFLAGS: 00010246 CPU:1
EIP is at blogic_init_mm_probeinfo.isra.17+0x20a/0x583
EAX: 00000013 EBX: 00000000 ECX: 00000000 EDX: f8001000
ESI: f71cb800 EDI: f7388000 EBP: 00007800 ESP: f7055c84
DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068
CR0: 8005003b CR2: 0000000c CR3: 0154f000 CR4: 000007d0
Stack:
0000001c 00000000 c11a59f6 f7055c98 00008130 ffffffff ffffffff 00000000
00000003 00000000 00000000 00000000 00000013 f8001000 00000001 000003d0
00000000 00000000 00000000 c14e3f84 f78803c8 00000000 f738c000 000000e9
Call Trace:
[<c11a59f6>] ? pci_get_subsys+0x33/0x38
[<c150c4fb>] ? blogic_init_probeinfo_list+0x4b/0x19e
[<c108d593>] ? __alloc_pages_nodemask+0xe3/0x623
[<c108d593>] ? __alloc_pages_nodemask+0xe3/0x623
[<c10fb99e>] ? sysfs_link_sibling+0x61/0x8d
[<c10b0519>] ? kmem_cache_alloc+0x8b/0xb5
[<c150cce5>] ? blogic_init+0xa1/0x10e8
[<c10fc0a8>] ? sysfs_add_one+0x10/0x9d
[<c10fc18a>] ? sysfs_addrm_finish+0x12/0x85
[<c10fca37>] ? sysfs_do_create_link_sd+0x9d/0x1b4
[<c117c272>] ? blk_register_queue+0x69/0xb3
[<c10fcb68>] ? sysfs_create_link+0x1a/0x2c
[<c1181a07>] ? add_disk+0x1a1/0x3c7
[<c138737b>] ? klist_next+0x60/0xc3
[<c122cc3a>] ? scsi_dh_detach+0x68/0x68
[<c1213e36>] ? bus_for_each_dev+0x51/0x61
[<c1000356>] ? do_one_initcall+0x22/0x12c
[<c10f3688>] ? __proc_create+0x8c/0xba
[<c150cc44>] ? blogic_setup+0x5f6/0x5f6
[<c14e94aa>] ? repair_env_string+0xf/0x4d
[<c14e949b>] ? do_early_param+0x71/0x71
[<c103efaa>] ? parse_args+0x21f/0x33d
[<c14e9a54>] ? kernel_init_freeable+0xdf/0x17d
[<c14e949b>] ? do_early_param+0x71/0x71
[<c1388b64>] ? kernel_init+0x8/0xc0
[<c1392222>] ? ret_from_kernel_thread+0x6/0x28
[<c1392227>] ? ret_from_kernel_thread+0x1b/0x28
[<c1388b5c>] ? rest_init+0x6c/0x6c
Code: 89 44 24 10 0f b6 44 24 3d 89 44 24 0c c7 44 24 08 00 00 00 00 c7 44 24 04 38 62 46 c1 c7 04 24 02 00 00 00 e8 78 13 d2 ff 31 db <89> 6b 0c b0 20 89 ea ee
c7 44 24 08 04 00 00 00 8d 44 24 4c 89
EIP: [<c150c137>] blogic_init_mm_probeinfo.isra.17+0x20a/0x583 SS:ESP 0068:f7055c84
CR2: 000000000000000c
---[ end trace 17f45f5196d40487 ]---
Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000009
Signed-off-by: Khalid Aziz <khalid.aziz@oracle.com>
Cc: <stable@vger.kernel.org> # 3.11.x
Reported-by: Pierre Uszynski <pierre@rahul.net>
Tested-by: Pierre Uszynski <pierre@rahul.net>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
This patch fixes a particular type of data corruption that has been
encountered when loading a snapshot's metadata from disk.
When we allocate a new chunk in persistent_prepare, we increment
ps->next_free and we make sure that it doesn't point to a metadata area
by further incrementing it if necessary.
When we load metadata from disk on device activation, ps->next_free is
positioned after the last used data chunk. However, if this last used
data chunk is followed by a metadata area, ps->next_free is positioned
erroneously to the metadata area. A newly-allocated chunk is placed at
the same location as the metadata area, resulting in data or metadata
corruption.
This patch changes the code so that ps->next_free skips the metadata
area when metadata are loaded in function read_exceptions.
The patch also moves a piece of code from persistent_prepare_exception
to a separate function skip_metadata to avoid code duplication.
CVE-2013-4299
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Cc: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
|
|
Pull device tree fixes and reverts from Grant Likely:
"One bug fix and three reverts. The reverts back out the slightly
controversial feeding the entire device tree into the random pool and
the reserved-memory binding which isn't fully baked yet. Expect the
reserved-memory patches at least to resurface for v3.13.
The bug fixes removes a scary but harmless warning on SPARC that was
introduced in the v3.12 merge window. v3.13 will contain a proper fix
that makes the new code work on SPARC.
On the plus side, the diffstat looks *awesome*. I love removing lines
of code"
* tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux:
Revert "drivers: of: add initialization code for dma reserved memory"
Revert "ARM: init: add support for reserved memory defined by device tree"
Revert "of: Feed entire flattened device tree into the random pool"
of: fix unnecessary warning on missing /cpus node
|
|
If the system is suspended while max_perf_pct is less than 100 percent
or no_turbo set policy->{min,max} will be set incorrectly with scaled
values which turn the scaled values into hard limits.
References: https://bugzilla.kernel.org/show_bug.cgi?id=61241
Reported-by: Patrick Bartels <petzicus@googlemail.com>
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Cc: 3.9+ <stable@vger.kernel.org> # 3.9+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull Xen fixes from Stefano Stabellini:
"A small fix for Xen on x86_32 and a build fix for xen-tpmfront on
arm64"
* tag 'stable/for-linus-3.12-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen: Fix possible user space selector corruption
tpm: xen-tpmfront: fix missing declaration of xen_domain
|
|
Commit 1696d9d (ACPI: Remove the old /proc/acpi/event interface)
left /proc/acpi/event in the ACPI_BUTTON help in Kconfig, so
remove it from there.
[rjw: Changelog]
Signed-off-by: Krzysztof Mazur <krzysiek@podlesie.net>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
In acpi_resume_power_resources() resource_lock should be released
when acpi_power_get_state() fails and before passing to next power
resource on the list.
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
DRI clients that tried to grab the TTM lock when the master (X server) was
switched away during a VT switch were sent the SIGTERM signal by the
kernel. Fix this so that they are only sent that signal when the master has
exited.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
The evict code may try to swap them out causing a BUG in the destroy
function.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Jakob Bornecrantz <jakob@vmware.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Usually the active scan mask is freed in __iio_update_buffers() when the buffer
is disabled. But when the device is still sampling when it is removed we'll end
up disabling the buffers in iio_disable_all_buffers(). So we also need to free
the active scan mask here, otherwise it will be leaked.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless into for-davem
|
|
This patch changes the behavior of TI SoC thermal driver
when there is a PCB thermal zone.
Instead of reporting an error code when reading from
PCB temperature sensor fails, this patch will make
the driver attempt to compose the hotspot extrapolation
based on bandgap readings only.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
|
|
Exynos4412
The commit d0a0ce3e77c795258d47f9163e92d5031d0c5221 ("thermal: exynos: Add
missing definations and code cleanup") has removed setting of test MUX address
value at TMU configuration setting.
This field is not present on Exynos4210 and Exynos5 SoCs. However on Exynos4412
SoC it is required to set this field after reset because without it TMU shows
maximal available temperature, which causes immediate platform shutdown.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
|
|
Up till now Exynos5250 and Exynos4412 had the same definitions for TMU
data. Following commit changes that, by introducing separate
exynos4412_default_tmu_data structure.
Since Exynos4412 was chronologically first, the corresponding name for
TMU registers and default data was renamed.
Additionally, new SOC_ARCH_EXYNOS4412 type has been defined.
Moreover, the SOC_ARCH_EXYNOS name has been changed to SOC_ARCH_EXYNOS5250.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
|
|
exynos_report_trigger()
The commit 4de0bdaa9677d11406c9becb70c60887c957e1f0
("thermal: exynos: Add support for instance based register/unregister")
broke check for presence of therm_dev at global thermal zone in
exynos_report_trigger().
The resulting wrong test prevents thermal_zone_device_update() call, which
calls handlers for situation when trip points are passed.
Such behavior prevents thermal driver from proper reaction (when TMU interrupt
is raised) in a situation when overheating is detected at TMU hardware.
It turns out, that after exynos thermal subsystem redesign (at v3.12) this
check is not needed, since it is not possible to register thermal zone
without valid thermal device.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@ti.com>
|
|
If EM Transmit bit is busy during init ata_msleep() is called. It is
wrong - msleep() should be used instead of ata_msleep(), because if EM
Transmit bit is busy for one port, it will be busy for all other ports
too, so using ata_msleep() causes wasting tries for another ports.
The most common scenario looks like that now
(six ports try to transmit a LED meaasege):
- port #0 tries for the 1st time and succeeds
- ports #1-5 try for the 1st time and sleeps
- port #1 tries for the 2nd time and succeeds
- ports #2-5 try for the 2nd time and sleeps
- port #2 tries for the 3rd time and succeeds
- ports #3-5 try for the 3rd time and sleeps
- port #3 tries for the 4th time and succeeds
- ports #4-5 try for the 4th time and sleeps
- port #4 tries for the 5th time and succeeds
- port #5 tries for the 5th time and sleeps
At this moment port #5 wasted all its five tries and failed to
initialize. Because there are only 5 (EM_MAX_RETRY) tries available
usually only five ports succeed to initialize. The sixth port and next
ones usually will fail.
If msleep() is used instead of ata_msleep() the first port succeeds to
initialize in the first try and next ones usually succeed to
initialize in the second try.
tj: updated comment
Signed-off-by: Lukasz Dorau <lukasz.dorau@intel.com>
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
Fix check within vmlogrdr_open() if the minor address is not larger
than the number of array elements.
Found with "smatch":
drivers/s390/char/vmlogrdr.c:318 vmlogrdr_open() warn:
buffer overflow 'sys_ser' 3 <= 3
Acked-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
The prefix command is used instead of a define extent to make use of
PAV alias devices during format. On some older storage servers the
prefix command may not be available and the IO request will fail.
Check for availability of prefix command and use define extent if
not available.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
This reverts commit 9d8eab7af79cb4ce2de5de39f82c455b1f796963. There is
still no consensus on the bindings for the reserved memory and various
drawbacks of the proposed solution has been shown, so the best now is to
revert it completely and start again from scratch later.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
|
|
Needed to prevent display corruption in high res panels.
v2: use correct unit names (Rodrigo)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Ulrich Drepper <drepper@gmail.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Pull vfio fix from Alex Williamson:
"Fix an incorrect break out of nested loop in iommu mapping code"
* tag 'vfio-v3.12-rc5' of git://github.com/awilliam/linux-vfio:
VFIO: vfio_iommu_type1: fix bug caused by break in nested loop
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband updates from Roland Dreier:
"Last batch of IB changes for 3.12: many mlx5 hardware driver fixes
plus one trivial semicolon cleanup"
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB: Remove unnecessary semicolons
IB/mlx5: Ensure proper synchronization accessing memory
IB/mlx5: Fix alignment of reg umr gather buffers
IB/mlx5: Fix eq names to display nicely in /proc/interrupts
mlx5: Fix error code translation from firmware to driver
IB/mlx5: Fix opt param mask according to firmware spec
mlx5: Fix opt param mask for sq err to rts transition
IB/mlx5: Disable atomic operations
mlx5: Fix layout of struct mlx5_init_seg
mlx5: Keep polling to reclaim pages while any returned
IB/mlx5: Avoid async events on invalid port number
IB/mlx5: Decrease memory consumption of mr caches
mlx5: Remove checksum on command interface commands
IB/mlx5: Fix memory leak in mlx5_ib_create_srq
IB/mlx5: Flush cache workqueue before destroying it
IB/mlx5: Fix send work queue size calculation
|
|
This reverts commit 9b0a1de3c85d99d881c86a29b3d52da7b9c7bd61.
Aaro writes:
With v3.12-rc4 I can no longer connect to N800 (OMAP2) with USB
(peripheral, g_ether).
According to git bisect this is caused by:
9b0a1de3c85d99d881c86a29b3d52da7b9c7bd61 is the first bad commit
So revert this patch, as Felipe says:
It's unfortunate that tusb6010 is so messed up
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Felipe Balbi <balbi@ti.com>
Cc: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The device is not responsive when resumed, unless it is reset.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
CC: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch adds missing cfg80211_disconnected event for P2P client
interface upon successful deauthenticate command, deauthenticate
event or disassociate event from FW.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
If device is surprise removed, commands sent to FW including
deauthenticate command fail as bus writes fail.
We update our media_connected status to false and inform cfg80211
about disconnection only when command is successful. Since cfg80211
assumes device is still connected, it results into following
WARN_ON during unload:
WARNING: CPU: 0 PID: 18245 at net/wireless/core.c:937
cfg80211_netdev_notifier_call+0x175/0x4d0 [cfg80211]()
Avoid this by emitting cfg80211_disconnected event even if the
deauthenticate command fails.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
|
|
These aren't necessary after switch blocks.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
"These fix two recent bugs in ACPIPHP (ACPI-based PCI hotplug) and
update a bunch of web links and e-mail addresses in MAINTAINERS, docs
and Kconfig that either are stale or will expire soon.
Specifics:
- The WARN_ON() in acpiphp_enumerate_slots() triggers as a false
positive in some cases, so drop it.
- Add a missing pci_dev_put() to an error code path in
acpiphp_enumerate_slots().
- Replace my old e-mail address that's going to expire with a new
one.
- Update ACPI web links and git tree information in MAINTAINERS.
- Update links to the Linux-ACPI project's page in MAINTAINERS.
- Update some stale links and e-mail addresses under Documentation
and in the ACPI Kconfig file"
* tag 'pm+acpi-3.12-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / hotplug / PCI: Drop WARN_ON() from acpiphp_enumerate_slots()
ACPI / hotplug / PCI: Fix error code path in acpiphp_enumerate_slots()
ACPI / PM / Documentation: Replace outdated project links and addresses
MAINTAINERS / ACPI: Update links to the Linux-ACPI project web page
MAINTAINERS / ACPI: Update links and git tree information
MAINTAINERS / Documentation: Update Rafael's e-mail address
|
|
This reverts commit 109b6236294b53d8eaa50be7d9e9ad37079f5f7e.
Tim Bird expressed concern that this will have a bad effect on boot
time, and while simple tests have shown it to be okay with simple tree,
a device tree blob can potentially be quite large and
add_device_randomness() is not a fast function. Rather than do this for
all platforms unconditionally, I'm reverting this patch and would like
to see it revisited. Instead of feeding the entire tree into the random
pool, it would probably be appropriate to hash the tree and feed the
hash result into the pool. There really isn't a lot of randomness in a
device tree anyway. In the majority of cases only a handful of
properties are going to be different between machines with the same
baseboard.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
