| Age | Commit message (Collapse) | Author |
|---|
|
This enables the current list of dynamic IDs to be read out through
either new_id or remove_id.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit f397d7c4c5e8a1eb93f2ed15808a509318ccf1dd.
This series isn't quite ready for 3.5 just yet, so revert it and give
the author more time to get it correct.
Cc: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit bebc56d58dc780539777d2b1ca80df5566e2ad87.
The call here is fragile and not well thought out, so revert it, it's
not fully baked yet and I don't want this to go into 3.5.
Cc: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Basically, ->vbus_session() calls should be served when VBUS session
starts and ends (it's not whenever transciever drivers detect VBUS
_changes_). Otherwise, if UDC gadget drivers don't want for some
reason ->vbus_session() calls with the same "is_active" value, either
OTG or UDC drivers need to have some protection handlings.
Also, on platforms using this 'gpio_vbus' driver, the driver is only
allowed to check whether VBUS is applied. There is no kernel-standard
way prepared for UDC gadget drivers to do that.
With this in mind, gpio_vbus should try to prevent unnecessary
consecutive vbus_session calls being served with the same "in_active"
value.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Note that regulator_put() doesn't care about whether ->vbus_draw is
valid or not.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In commit c2344f13b59e007d782a3e591ebc551bc583a8b7 (USB: gpio_vbus:
add delayed vbus_session calls, 2009-01-24), usb_gadget_vbus_connect()
and ...disconnect() were extracted from the interrupt handler, so to
allow vbus_session handlers to deal with msleep() calls.
This patch takes the approach one step further.
USB2.0 specification (7.1.7.3 Connect and Disconnect Signaling) says
that the USB system software (shall) provide a debounce interval with
a minimum duration of 100 ms, which ensures that the electrical and
mechanical connection is stable before software attempts to reset
the attached device.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
'dev_id' has to be the same with the one passed to request_irq().
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If no default value is specified, then 'n' is used so the default value
used here is not needed. Furthermore, we should never change default
values depending on EXPERT mode. EXPERT mode should only make options
visible, not change them.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Currently usb_put_transceiver calls put_device so this is a no-op but it
is better to keep API usage consistent as ohci->transceiver is allocated
with usb_get_transceiver.
While at there remove one extra ohci->transceiver test as the code block
has already tested it.
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Currently usb_put_transceiver calls put_device so this is a no-op but it
is better to keep API usage consistent as ehci->transceiver is allocated
with usb_get_transceiver.
While at there remove one extra ehci->transceiver test as the code block
has already tested it.
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Move child's pointer to the struct usb_hub_port since the child device
is directly associated with the port. Provide usb_get_hub_child_device()
to get child's pointer.
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add struct usb_hub_port pointer port_data in the struct usb_hub and allocate
struct usb_hub_port perspectively for each ports to store private data.
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
ACPI offers two methods that allow us to infer whether or not a USB port
is removable. The _PLD method gives us information on whether the port is
"user visible" or not. If that's not present then we can fall back to the
_UPC method which tells us whether or not a port is connectable.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Built-in USB devices will typically have a representation in the system
ACPI tables. Add support for binding the two together so the USB code can
make use of the associated methods.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add a simple helper function to allow drivers to obtain the physical
device location data.
Acked-by: Len Brown <len.brown@intel.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
It's unreasonable to have CONFIG_ACPI for these in drivers, so add some
stub functions.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We have the chipidea driver now that supports both langwell and penwell,
so there is no need for this one any more.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
It was used as a shorthand for gadget's device in request mapping/unmapping
code, but now it's not used any more.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We're one of the remaining drivers to map/unmap requests by hand. Switch
to using generic gadget routines for that instead.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Some implementations need this limitation to work correctly.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This adds EHCI host support to the chipidea driver. We want it to be
part of the hdrc driver and not a standalone (sub-)driver module, as
the structure of ehci-hcd.c suggests, so for chipidea controller we
hack it to not provide platform-related code, but only the ehci hcd.
The ehci-platform driver won't work for us here too, because the
controller uses the same registers for both device and host mode and
also otg-related bits, so it's not really possible to put ehci registers
into a separate resource.
This is not a pretty solution, but the alternative is exporting symbols
from the chipidea driver to a ehci-chipidea driver and doing all the
module refcounting.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Some of the bits of USBMODE register are defined in <usb/ehci_def.h>,
use them instead of having our own definitions.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
These definitions are unused, and the same registers are also defined
in <linux/usb/msm_hsusb_hw.h>.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Currently, gadget can't be NULL in _gadget_stop_activity().
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Reported-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Move spin_lock under the done label, so the
lock will also be pulled in the error paths.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
[rebased on top of the patchset]
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Get rid of trailing comments in the structure definitions in favor of
kernel-doc.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The old implementation used global hw_bank, the new implementation uses
udc-local hw_bank. This field seems to be a leftover from previous coding
experiments.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add some generic code for roles and implement simple role switching
based on ID pin state and/or a sysfs file. At this, we also rename
the device to ci_hdrc, which is what it is.
The "manual" switch is made into a sysfs file and not debugfs, because
it might be useful even in non-debug context. For some boards, like
sheevaplug, it seems to be the only way to switch roles without modifying
the hardware, since the ID pin is always grounded.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Split the driver into the following parts:
* core -- resources, register access, capabilities, etc;
* udc -- device controller functionality;
* debug -- logging events.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Since chipidea is a dual role controller, it makes sense to move it
to its own directory, where we can also have host, otg and platform
code related to this controller. It also makes sense to break out
the driver into several compilation units like udc, host, debugging
code, etc.
Firstly, let's move the udc and platform code to drivers/usb/chipidea.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Report basic information about capabilities and register addresses on
probe.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Newer versions of the chipidea controller support the "advance" setting
of usb address, which means instead of setting it immediately, deferring
it till the status completion. Unfortunately, older versions of the
controller don't have this feature, so in order to support those too, we
simply don't use it. It's about 4 lines of extra code, and isn't in any
way critical to performance. While at it, change the return value of the
hw_usb_set_address() to void, since it can't fail in any measurable way.
With this patch, ci13xxx_udc driver works with the chipidea controller in
kirkwood (feroceon SoC), as found in, for example, sheevaplug.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The regmap field is an array of register pointers, not the other way
around.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There is no point in having tracing output in the kernel these days.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Don't try to initialize devices that don't have driver_data assigned
to their pci ids.
Reported-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Prevents dereferencing an invalid struct usb_interface
pointer.
Always delete entry from device list whether or not the
rest of the device state cleanup is postponed. The device
list uses desc->intf as key, and wdm_open will dereference
this key while searching for a matching device. A device
should not appear in the list unless probe() has succeeded
and disconnect() has not finished.
Cc: Oliver Neukum <oliver@neukum.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We cannot dereference a removed USB interface for
dev_printk. Use pr_debug instead where necessary.
Flush errors are expected if device is unplugged and are
therefore best ingored at this point.
Move the kill_urbs() call in wdm_release with dev_dbg()
for the non disconnect, as we know it has already been
called if WDM_DISCONNECTING is set. This does not
actually fix anything, but keeps the code more consistent.
Cc: Oliver Neukum <oliver@neukum.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Else the poll will be restarted indefinitely in a tight loop,
preventing final device cleanup.
Cc: Oliver Neukum <oliver@neukum.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The warning shown up when ran with randconfig,
warning: (USB_DWC3) selects USB_XHCI_PLATFORM which has unmet direct dependencies (USB_SUPPORT && USB_XHCI_HCD)
Signed-off-by: joseph daniel <josephdanielwalter@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use WARN_ON() instead of __WARN, which also means we won't use any
internal macros.
Signed-off-by: Sasha Levin <levinsasha928@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix driver to work properly in big endian mode.
Signed-off-by: Steven J. Hill <sjhill@mips.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The Kontron M2M development board, also known as the Fish River Island II,
has an optional daughter card providing access to the PCH_UART (EG20T) via
a ti_usb_3410_5052 uart to usb chip.
http://us.kontron.com/products/systems+and+platforms/m2m/m2m+smart+services+developer+kit.html
Signed-off-by: Darren Hart <dvhart@linux.intel.com>
CC: Al Borchers <alborchers@steinerpoint.com>
CC: Peter Berger <pberger@brimson.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
With a previous patch, the usb_driver suspend/resume callbacks got
overridden and were never called if a usb_serial driver defined them.
This patch fixes the opticon driver to move the suspend/resume callbacks
into the usb_serial_driver structure where they will be properly called.
It then removes the unused usb_driver structure.
Cc: Johan Hovold <jhovold@gmail.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Cc: Julia Lawall <julia@diku.dk>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There are a number of device ids that the quatech2 driver supports that
are duplicated in the serqt_usb2 driver, so remove them from the
serqt_usb2 driver as they do not belong there.
Reported-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Now that we have a "real" driver for the quatech devices, we can remove
the drivers/staging/quatech_usb2/ driver as it is no longer needed.
Thanks to Bill Pemberton for writing the new driver.
Cc: Richard Ash <richard@audacityteam.org>
Cc: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add a copyright and license statement to the head of quatech.c source
file. No code change here.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This supports the Quatech USB 2 usb to serial adapters.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add a variant of rndis_bind_config to let gadget drivers change
rndis vendorID and manufacturer parameters.
Signed-off-by: Benoit Goby <benoit@android.com>
[make rndis_bind_config a static inline function]
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
f_rndis checks if rndis_string_defs[0].id is null to setup rndis
and allocate string ids when it is bound to the first configuration:
/* maybe allocate device-global string IDs */
if (rndis_string_defs[0].id == 0) {
/* ... and setup RNDIS itself */
status = rndis_init();
if (status < 0)
return status;
rndis_string_defs[0].id must be reset to 0 on unbind for rndis to be
correctly initialized on the next composite_bind.
Signed-off-by: Benoit Goby <benoit@android.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
