| Age | Commit message (Collapse) | Author |
|---|
|
CB3.2 and earlier hardware has silicon bugs that are no longer needed with
the new hardware. We don't have to use a NULL op to signal interrupt for
RAID ops any longer. This code make sure the legacy workarounds only happen on
legacy hardware.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Dan Williams <djbw@fb.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Since we have proper ACPI DMA helpers implemented, the driver may use it. This
patch introduces custom filter function together with acpi_device_id table.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
The slave device could be enumerated by ACPI. In that case the
dma_request_slave_channel should use the acpi_dma_request_slave_channel()
helper.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
There is a new generic API to get a DMA channel for a slave device (commit
9a6cecc8 "dmaengine: add helper function to request a slave DMA channel"). In
similar fashion to the DT case (commit aa3da644 "of: Add generic device tree
DMA helpers") we introduce helpers to the DMAC drivers which are enumerated by
ACPI.
The proposed extension provides the following API calls:
acpi_dma_controller_register(), devm_acpi_dma_controller_register()
acpi_dma_controller_free(), devm_acpi_dma_controller_free()
acpi_dma_simple_xlate()
acpi_dma_request_slave_chan_by_index()
acpi_dma_request_slave_chan_by_name()
The first two should be used, for example, at probe() and remove() of the
corresponding DMAC driver. At the register stage the DMAC driver supplies a
custom xlate() function to translate a struct dma_spec into struct dma_chan.
Accordingly to the ACPI Fixed DMA resource specification the only two pieces of
information the slave device has are the channel id and the request line (slave
id). Those two are represented by struct dma_spec. The
acpi_dma_request_slave_chan_by_index() provides access to the specifix FixedDMA
resource by its index. Whereas dma_request_slave_channel() takes a string
parameter to identify the DMA resources required by the slave device. To make a
slave device driver work with both DeviceTree and ACPI enumeration a simple
convention is established: "tx" corresponds to the index 0 and "rx" to the
index 1. In case of robust configuration the slave device driver unfortunately
needs to call acpi_dma_request_slave_chan_by_index() directly.
Additionally the patch provides "managed" version of the register/free pair
i.e. devm_acpi_dma_controller_register() and devm_acpi_dma_controller_free().
Usually, the driver uses only devm_acpi_dma_controller_register().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
The alignment workaround is only necessary for cb3.2 or earlier platforms.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Dan Williams <djbw@fb.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
The PQ Val ops work on the newer hardware so we should actually provide support
for it and remove the disabling bits.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Dan Williams <djbw@fb.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Make it so only 3.2 and earlier platform need the PCI config register
clearings since this implementation does not have the registers.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Dan Williams <djbw@fb.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
The Intel Atom S1200 family ioatdma changed the channel reset behavior.
It does a reset similar to PCI FLR by resetting all the MSIX
registers. We have to re-init msix interrupts because of this. This
workaround is only specific to this platform and is not expected to carry
over to the later generations.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Dan Williams <djbw@fb.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
The channel status register for v3.3 is now 64bit. Use readq if available
on v3.3 platforms.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Dan Williams <djbw@fb.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
These should be good for the IOAT DMA devices on the Intel Atom S1269,
S1279, and S1289 platforms. We are also adding IOAT v3.3 definition for
the new DMA engine.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Dan Williams <djbw@fb.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Adding Haswell PCI device IDs for ioatdma and simplify the detection of
certain Xeon CPUs that has alignment bugs so that modifications can be
changed at a single place going forward.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Dan Williams <djbw@fb.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
If the device-tree blob is present during boot, then register the SDMA
controller with the device-tree DMA driver so that we can use device-tree
to look-up DMA client information.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
If CONFIG_OF is not set the of_node of the device will always be NULL.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
The patch to add the common DMA binding added a dummy dw_dma_slave
structure into the dw_dma_chan structure in order to configure the
masters correctly. It turns out that this can be simplified if we
pick the DMA masters in the dwc_alloc_chan_resources function instead
and save them in the dw_dma_chan structure directly.
This could be simplified further once all users that today use
dw_dma_slave for configuration get converted to device tree based
setup instead.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Cc: linux-arm-kernel@lists.infradead.org
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Since we will have not only DT cases in future let's rename DT related methods
to reflect their belonging.
The rename was done as follows:
struct dw_dma_filter_args -> struct dw_dma_of_filter_args
dw_dma_generic_filter() -> dw_dma_of_filter()
dw_dma_xlate() -> dw_dma_of_xlate()
dw_dma_id_table -> dw_dma_of_id_table
There is no functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Let's use capital letter as a first one in the comments.
There is no functional changes.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
The 'mask' parameter is not modified in __dma_request_channel and really
shouldn't be. Make this explicit by making the parameter const.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
there is hardcode which enabled the clock of dmaengine before,
this patch takes the clock by standard clock API and enable it
in probe.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
When we pause the channel after transfer is completed we might stuck in the
dwc_chan_pause() because the FIFO_EMPTY flag will never be asserted. To avoid
the endless loop we introduce a timeout here (*). The proper solution is to
somehow get the residue in FIFO and avoid busyloop when transfer is done, but
this task is not simple and fast.
Unfortunately we can't use cpu_relax() in conjunction with jiffies checker, due
to we have interrupts disabled by spin_lock_irqsave() and there is a big chance
that no interrupts will come to update the jiffies..
(*) The worst case is
AHB write * FIFO size / hclk = 5.12 us,
where
AHB write = 2 cycles,
hclk = 100 MHz,
burst size = 1 byte,
FIFO size = 256 bytes.
The proposed 40us timeout might be considered as a big one, though we enter
to that state only when we have the transfer already completed.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
kfree on NULL pointer is a no-op.
Signed-off-by: Syam Sidhardhan <s.syam@samsung.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Since commit 84c1e63c12 (dma: Remove erroneous __exit and __exit_p() references)
the following section mismatch happens:
WARNING: drivers/built-in.o(.text+0x20f94): Section mismatch in reference from the function ipu_remove() to the function .exit.text:ipu_idmac_exit()
The function ipu_remove() references a function in an exit section.
Often the function ipu_idmac_exit() has valid usage outside the exit section
and the fix is to remove the __exit annotation of ipu_idmac_exit.
Remove the '__exit' annotation from ipu_idmac_exit in order to fix it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Maxin B. John <maxin.john@enea.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Tegra only supports, and always enables, device tree. Remove all ifdefs
and runtime checks for DT support from the driver.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Use the newly introduced devm_ioremap_resource() instead of
devm_request_and_ioremap() which provides more consistent error handling.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Reviewed-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Comparison between buffers is stored to the dedicated structure.
Note that the verify result is now accessible only via file 'results' in the
debugfs.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
The patch provides a storage for the test results in the linked list. The
gathered data could be used after test is done.
The new file 'results' represents gathered data of the in progress test. The
messages collected are printed to the kernel log as well.
Example of output:
% cat /sys/kernel/debug/dmatest/results
dma0chan0-copy0: #1: No errors with src_off=0x7bf dst_off=0x8ad len=0x3fea (0)
The message format is unified across the different types of errors. A number in
the parens represents additional information, e.g. error code, error counter,
or status.
Note that the buffer comparison is done in the old way, i.e. data is not
collected and just printed out.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Its meaning is to limit amount of error messages to be printed out when buffer
mismatch is occured.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
The following command should return actual state of the test.
% cat /sys/kernel/debug/dmatest/run
To wait for test done the user may perform a busy loop that checks the state.
% while [ $(cat /sys/kernel/debug/dmatest/run) = "Y" ]
> do
> echo -n "."
> sleep 1
> done
> echo
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Instead of doing
modprobe dmatest ...
modprobe -r dmatest
we allow user to run tests interactively.
The dmatest could be built as module or inside kernel. Let's consider those
cases.
1. When dmatest is built as a module...
After mounting debugfs and loading the module, the /sys/kernel/debug/dmatest
folder with nodes will be created. They are the same as module parameters with
addition of the 'run' node that controls run and stop phases of the test.
Note that in this case test will not run on load automatically.
Example of usage:
% echo dma0chan0 > /sys/kernel/debug/dmatest/channel
% echo 2000 > /sys/kernel/debug/dmatest/timeout
% echo 1 > /sys/kernel/debug/dmatest/iterations
% echo 1 > /sys/kernel/debug/dmatest/run
After a while you will start to get messages about current status or error like
in the original code.
Note that running a new test will stop any in progress test.
2. When built-in in the kernel...
The module parameters that is supplied to the kernel command line will be used
for the first performed test. After user gets a control, the test could be
interrupted or re-run with same or different parameters. For the details see
the above section "1. When dmatest is built as a module..."
In both cases the module parameters are used as initial values for the test case.
You always could check them at run-time by running
% grep -H . /sys/module/dmatest/parameters/*
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Better to keep test parameters separate from internal variables.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
We don't need to have them global and later we would like to protect access to
them as well.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
The proposed change will remove usage of the module parameters as global
variables. In future it helps to run different test cases sequentially.
The patch introduces the run_threaded_test() and stop_threaded_test() functions
that could be used later outside of dmatest_init, dmatest_exit scope.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
This will help in future to hide a global variable usage.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
If user have the timeout alike issues and wants to cancel the thread
immediately, the current call of wait_event_freezable_timeout is preventing to
this until timeout is expired. Thus, user will experience the unnecessary
delays.
Adding kthread_should_stop() check inside wait_event_freezable_timeout() solves
that.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Looks like only the RAID channels are allowed to have irq coalescing support
in the existing code. Fixing that. The ioat3 cleanup code can handle memcpy
ops anyways
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Dan Williams <djbw@fb.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Making OP field a hex instead of integer to make it more readable. Also add
the dump out of the NEXT field.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Acked-by: Dan Williams <djbw@fb.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Removing the annotation with __exit and referencing with __exit_p()
present in dma driver module remove hooks.
Part of the __devexit and __devexit_p() purge.
Signed-off-by: Maxin B. John <maxin.john@enea.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Fix this compiler warning:
warning: 'td_remove' defined but not used [-Wunused-function]
Signed-off-by: Maxin B. John <maxin.john@enea.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
pdc_desc_get() is called from pd_prep_slave_sg, and the function is
called from interrupt context(e.g. Uart driver "pch_uart.c").
In fact, I saw kernel error message.
So, GFP_ATOMIC must be used not GFP_NOIO.
Signed-off-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Fix the logic to allow mc programming of second transfer after first
has been done, by removing immediate return upon success and iterating
until we detect QFull or DMAC dying.
Reported-by: Alvaro Moran <dirac3000@gmail.com>
Tested-by: Alvaro Moran <dirac3000@gmail.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Pull drm fixes from Dave Airlie:
"One fix for a hotplug locking regressions, and one fix for an oops if
you unplug the monitor at an inopportune moment on the udl device."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/fb-helper: Fix locking in drm_fb_helper_hotplug_event
udl: handle EDID failure properly.
|
|
Compiling the at91rm9200_wdt.c driver without at91rm9200
support was leading to several errors:
drivers/built-in.o: In function `at91_wdt_close':
at91_adc.c:(.text+0xc9fe4): undefined reference to `at91_st_base'
drivers/built-in.o: In function `at91_wdt_write':
at91_adc.c:(.text+0xca004): undefined reference to `at91_st_base'
drivers/built-in.o: In function `at91wdt_shutdown':
at91_adc.c:(.text+0xca01c): undefined reference to `at91_st_base'
drivers/built-in.o: In function `at91wdt_suspend':
at91_adc.c:(.text+0xca038): undefined reference to `at91_st_base'
drivers/built-in.o: In function `at91_wdt_open':
at91_adc.c:(.text+0xca0cc): undefined reference to `at91_st_base'
drivers/built-in.o:at91_adc.c:(.text+0xca2c8): more undefined references to
`at91_st_base' follow
So, reverting the modification of the "depends" Kconfig line
introduced by patch a6a1bcd37 (watchdog: at91rm9200: add DT support)
seems to be the good solution.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
Pull SCSI target fixes from Nicholas Bellinger:
"Here are remaining target-pending items for v3.9-rc7 code.
The tcm_vhost patches are more than I'd usually include in a -rc7
pull, but are changes required for v3.9 to work correctly with the
pending vhost-scsi-pci QEMU upstream series merge. (Paolo CC'ed)
Plus Asias's conversion to use vhost_virtqueue->private_data + RCU for
managing vhost-scsi endpoints has gotten alot of review + testing over
the past weeks, and MST has ACKed the full series.
Also, there is a target patch to fix a long-standing bug within
control CDB handling with Standby/Offline/Transition ALUA port access
states, that had been incorrectly rejecting the control CDBs required
for LUN scan to work during these port group states. CC'ing to
stable."
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
target: Fix incorrect fallthrough of ALUA Standby/Offline/Transition CDBs
tcm_vhost: Send bad target to guest when cmd fails
tcm_vhost: Add vhost_scsi_send_bad_target() helper
tcm_vhost: Fix tv_cmd leak in vhost_scsi_handle_vq
tcm_vhost: Remove double check of response
tcm_vhost: Initialize vq->last_used_idx when set endpoint
tcm_vhost: Use vq->private_data to indicate if the endpoint is setup
tcm_vhost: Use ACCESS_ONCE for vs->vs_tpg[target] access
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is a set of ten bug fixes (and two consisting of copyright year
update and version number change) pretty much all of which involve
either a crash or a hang except the removal of the random sleep from
the qla2xxx driver (which is a coding error so bad, we want it gone
before anyone has a chance to copy it)."
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
[SCSI] lpfc: fix potential NULL pointer dereference in lpfc_sli4_rq_put()
[SCSI] libsas: fix handling vacant phy in sas_set_ex_phy()
[SCSI] ibmvscsi: Fix slave_configure deadlock
[SCSI] qla2xxx: Update the driver version to 8.04.00.13-k.
[SCSI] qla2xxx: Remove debug code that msleeps for random duration.
[SCSI] qla2xxx: Update copyright dates information in LICENSE.qla2xxx file.
[SCSI] qla2xxx: Fix crash during firmware dump procedure.
[SCSI] Revert "qla2xxx: Add setting of driver version string for vendor application."
[SCSI] ipr: dlpar failed when adding an adapter back
[SCSI] ipr: fix addition of abort command to HRRQ free queue
[SCSI] st: Take additional queue ref in st_probe
[SCSI] libsas: use right function to alloc smp response
[SCSI] ipr: ipr_test_msi() fails when running with msi-x enabled adapter
|
|
Driver's and ->fill_modes functions are allowed to grab crtc mutexes
(for e.g. load detect). Hence we need to first only grab the general
kms mutex, and only in a second step grab all locks to do the
modesets.
This prevents a deadlock on my gm45 in the tv load detect code called
by drm_helper_probe_single_connector_modes.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Don't oops seems proper.
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Pull slave-dmaengine fixes from Vinod Koul:
"The first one fixes issue in pl330 to check for DT compatible and
the second one fixes omap-dma to start without delay"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: omap-dma: Start DMA without delay for cyclic channels
DMA: PL330: Add check if device tree compatible
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
- System reboot/halt fix related to CPU offline ordering from Huacai
Chen.
- intel_pstate driver fix for a delay time computation error
occasionally crashing systems using it from Dirk Brandewie.
* tag 'pm-3.9-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / reboot: call syscore_shutdown() after disable_nonboot_cpus()
cpufreq / intel_pstate: Set timer timeout correctly
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap revert from Mark Brown:
"regmap: Back out work buffer fix
This reverts commit bc8ce4 (regmap: don't corrupt work buffer in
_regmap_raw_write()) since it turns out that it can cause issues when
taken in isolation from the other changes in -next that lead to its
discovery. On the basis that nobody noticed the problems for quite
some time without that subsequent work let's drop it from v3.9."
* tag 'regmap-v3.9-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: Back out work buffer fix
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fix from Linus Walleij:
"Oneliner fix for the PCA 953x driver."
* tag 'gpio-fixes-v3.9-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: pca953x: fix irq_domain_add_simple usage
|
|
The dereference to 'put_index' should be moved below the NULL test.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
