| Age | Commit message (Collapse) | Author |
|---|
|
Description of the problem:
- i2c-scmi driver contains only two identifiers "SMBUS01" and "SMBUSIBM";
- the fist HID (SMBUS01) is clearly defined in "SMBus Control Method
Interface Specification, version 1.0": "Each device must specify
'SMBUS01' as its _HID and use a unique _UID value";
- unfortunately, BIOS vendors (like AMI) seem to ignore this requirement
and implement "SMB0001" HID instead of "SMBUS01";
- I speculate that they do this because only "SMB0001" is hard coded in
Windows SMBus driver produced by Microsoft.
This leads to following situation:
- SMBus works out of box in Windows but not in Linux;
- board vendors are forced to add correct "SMBUS01" HID to BIOS to make
SMBus work in Linux. Moreover the same board vendors complain that
tools (3-rd party ASL compiler) do not like the "SMBUS01" identifier
and produce errors. So they need to constantly patch the compiler for
each new version of BIOS.
As it is very unlikely that BIOS vendors implement a correct HID in
future, I would propose to consider whether it is possible to work around
the problem by adding MS HID to the Linux i2c-scmi driver.
v2: move the definition of the new HID to the driver itself.
Signed-off-by: Edgar Cherkasov <echerkasov@dev.rtsoft.ru>
Signed-off-by: Michael Brunner <Michael.Brunner@kontron.com>
Acked-by: Viktor Krasnov <vkrasnov@dev.rtsoft.ru>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
i2c/for-4.12
Pull in changes from the i2c-mux subsubsystem:
"Here are a new LTC4306/5 driver, a fix needed by the RT kernel and some
error message cleanup."
|
|
This patch adds support for the Analog Devices / Linear Technology
LTC4306 and LTC4305 4/2 Channel I2C Bus Multiplexer/Switches.
The LTC4306 optionally provides two general purpose input/output pins
(GPIOs) that can be configured as logic inputs, opendrain outputs or
push-pull outputs via the generic GPIOLIB framework.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Peter Rosin <peda@axentia.se>
|
|
i2c_mux_add_adapter already logs a message on failure.
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Peter Rosin <peda@axentia.se>
|
|
i2c_mux_add_adapter already logs a message on failure.
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Peter Rosin <peda@axentia.se>
|
|
i2c_mux_add_adapter already logs a message on failure.
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Peter Rosin <peda@axentia.se>
|
|
i2c_mux_add_adapter already logs a message on failure.
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Peter Rosin <peda@axentia.se>
|
|
i2c_mux_add_adapter already logs a message on failure.
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Peter Rosin <peda@axentia.se>
|
|
i2c_mux_add_adapter already logs a message on failure.
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Peter Rosin <peda@axentia.se>
|
|
No callers then need to report any further info, thus reducing both the
amount of code and the log noise.
Reviewed-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Peter Rosin <peda@axentia.se>
|
|
The preceding changes in this patch series now allow to simplify
the interrupt handler significantly.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
meson_i2c_write_tokens is always called directly after
meson_i2c_prepare_xfer (and only then). So we can simplify the code by
removing meson_i2c_write_tokens and moving the two statements of
meson_i2c_write_tokens to the end of meson_i2c_prepare_xfer.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
We can directly add the stop token to the token chain including the
last transfer chunk. This is more efficient than creating a separate
token chain just for the stop command.
And it allows us to get rid of state STATE_STOP completely.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
If state is STATE_IDLE no interrupt should occur. Return IRQ_NONE
if such a spurious interrupt is detected.
Not having to take care of STATE_IDLE later in the interrupt handler
allows to further simplify the interrupt handler in subsequent
patches of this series.
In addition move resetting REG_CTRL_START bit to the start of the
interrupt handler to ensure that the start bit is always reset.
Currently the start bit is not reset for STATE_STOP because
i2c->state is set to STATE_IDLE.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Variable count has always the same value as i, so we don't need it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
The clock divider has 12 bits, splitted into a 10 bit field and a
2 bit field. The extra 2 bits aren't used currently.
Change this to use the full 12 bits and warn if the requested
frequency is too low.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
We don't have to parse the DT manually to retrieve the bus frequency
and we don't have to maintain an own default for the bus frequency.
Let the i2c core do this for us.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
The bus frequency is fixed to what is set DT, therefore we can set
the clock divider in probe already and we don't have to set it for
each transfer.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Member irq can be replaced with a local variable in probe
because it's nowhere else accessed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Use min instead of min_t where min_t isn't needed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Add support for reading the system clock and the TWSI clock
frequency from ACPI DSDT.
TWSI clock was already covered by using device_property_read().
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
ARCH_VULCAN arm64 platform (for Broadcom Vulcan ARM64 processors) has
been discontinued. Cavium's ThunderX2 CN99XX (ARCH_THUNDER2) will be
the next revision of the platform.
Update compile dependencies and ACPI ID to reflect this change. There
is not need to retain ARCH_VULCAN since the Vulcan processor was never
in production and the config option will be removed soon.
Signed-off-by: Jayachandran C <jnair@caviumnetworks.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
As of commit bb475230b8e5 ("reset: make optional functions really
optional"), the reset framework API calls use NULL pointers to describe
optional, non-present reset controls.
This allows to return errors from devm_reset_control_get_optional and to
call reset_control_(de)assert unconditionally.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Enable the Tegra BPMP I2C adapter by default if the Tegra BPMP itself
is enabled. This adapter is used as the I2C interface for the PMIC on
the Tegra186 Jetson-TX2 platform.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Cherrytrail devices use the dw i2c-bus with uid 7 to access their PMIC.
Even if the i2c-bus to the PMIC is not shared with the SoC's P-Unit
and i2c-designware-baytrail.c thus does not set the pm_disabled flag,
we still need to disable pm so that ACPI PMIC opregions can access the
PMIC during late-suspend and early-resume.
This fixes errors like these blocking suspend:
i2c_designware 808622C1:06: timeout waiting for bus ready
ACPI Exception: AE_ERROR, Returned by Handler for [UserDefinedRegion]
acpi 80860F14:02: Failed to change power state to D3hot
PM: late suspend of devices failed
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Currently we are already setting a pm_runtime_disabled flag and disabling
runtime-pm for i2c-busses used for accessing the system PMIC on x86.
But this is not enough, there are ACPI opregions which may want to access
the PMIC during late-suspend and early-resume, so we need to completely
disable pm to be safe.
This commit renames the flag from pm_runtime_disabled to pm_disabled and
adds the following new behavior if the flag is set:
1) Call dev_pm_syscore_device(dev, true) which disables normal suspend /
resume and remove the pm_runtime_disabled check from dw_i2c_plat_resume
since that will now never get called. This fixes suspend_late handlers
which use ACPI PMIC opregions causing errors like these:
PM: Suspending system (freeze)
PM: suspend of devices complete after 1127.751 msecs
i2c_designware 808622C1:06: timeout waiting for bus ready
ACPI Exception: AE_ERROR, Returned by Handler for [UserDefinedRegion]
acpi 80860F14:02: Failed to change power state to D3hot
PM: late suspend of devices failed
2) Set IRQF_NO_SUSPEND irq flag. This fixes resume_early handlers which
handlers which use ACPI PMIC opregions causing errors like these:
PM: resume from suspend-to-idle
i2c_designware 808622C1:06: controller timed out
ACPI Exception: AE_ERROR, Returned by Handler for [UserDefinedRegion]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Our testing shows the semaphore failing to be transferred on CherryTrail
in about 0.5% of all cases. The existing timeout needs to be lengthened
to accommodate the worst cases.
V2: Rebased on https://cgit.freedesktop.org/drm-intel/commit/?h=topic/designware-baytrail
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
git://anongit.freedesktop.org/git/drm-intel into i2c/for-next
Pull immutable branch as a common base for further development:
"Baytrail PMIC vs. PMU race fixes from Hans de Goede
This time the right version (v4), with the compile fix."
|
|
Pull SCSI target fixes from Nicholas Bellinger:
"The bulk of the changes are in qla2xxx target driver code to address
various issues found during Cavium/QLogic's internal testing (stable
CC's included), along with a few other stability and smaller
miscellaneous improvements.
There are also a couple of different patch sets from Mike Christie,
which have been a result of his work to use target-core ALUA logic
together with tcm-user backend driver.
Finally, a patch to address some long standing issues with
pass-through SCSI export of TYPE_TAPE + TYPE_MEDIUM_CHANGER devices,
which will make folks using physical (or virtual) magnetic tape happy"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (28 commits)
qla2xxx: Update driver version to 9.00.00.00-k
qla2xxx: Fix delayed response to command for loop mode/direct connect.
qla2xxx: Change scsi host lookup method.
qla2xxx: Add DebugFS node to display Port Database
qla2xxx: Use IOCB interface to submit non-critical MBX.
qla2xxx: Add async new target notification
qla2xxx: Export DIF stats via debugfs
qla2xxx: Improve T10-DIF/PI handling in driver.
qla2xxx: Allow relogin to proceed if remote login did not finish
qla2xxx: Fix sess_lock & hardware_lock lock order problem.
qla2xxx: Fix inadequate lock protection for ABTS.
qla2xxx: Fix request queue corruption.
qla2xxx: Fix memory leak for abts processing
qla2xxx: Allow vref count to timeout on vport delete.
tcmu: Convert cmd_time_out into backend device attribute
tcmu: make cmd timeout configurable
tcmu: add helper to check if dev was configured
target: fix race during implicit transition work flushes
target: allow userspace to set state to transitioning
target: fix ALUA transition timeout handling
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull device-dax fixes from Dan Williams:
"The device-dax driver was not being careful to handle falling back to
smaller fault-granularity sizes.
The driver already fails fault attempts that are smaller than the
device's alignment, but it also needs to handle the cases where a
larger page mapping could be established. For simplicity of the
immediate fix the implementation just signals VM_FAULT_FALLBACK until
fault-size == device-alignment.
One fix is for -stable to address pmd-to-pte fallback from the
original implementation, another fix is for the new (introduced in
4.11-rc1) pud-to-pmd regression, and a typo fix comes along for the
ride.
These have received a build success notification from the kbuild
robot"
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
device-dax: fix debug output typo
device-dax: fix pud fault fallback handling
device-dax: fix pmd/pte fault fallback handling
|
|
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
signed-off-by: Giridhar Malavali <giridhar.malavali@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Current driver wait for FW to be in the ready state before
processing in-coming commands. For Arbitrated Loop or
Point-to- Point (not switch), FW Ready state can take a while.
FW will transition to ready state after all Nports have been
logged in. In the mean time, certain initiators have completed
the login and starts IO. Driver needs to start processing all
queues if FW is already started.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
For target mode, when new scsi command arrive, driver first performs
a look up of the SCSI Host. The current look up method is based on
the ALPA portion of the NPort ID. For Cisco switch, the ALPA can
not be used as the index. Instead, the new search method is based
on the full value of the Nport_ID via btree lib.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
The Mailbox interface is currently over subscribed. We like
to reserve the Mailbox interface for the chip managment and
link initialization. Any non essential Mailbox command will
be routed through the IOCB interface. The IOCB interface is
able to absorb more commands.
Following commands are being routed through IOCB interface
- Get ID List (007Ch)
- Get Port DB (0064h)
- Get Link Priv Stats (006Dh)
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Signed-off-by: Anil Gurumurthy <anil.gurumurthy@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Add routines to support T10 DIF tag.
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Anil Gurumurthy <anil.gurumurthy@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
If the remote port have started the login process, then the
PLOGI and PRLI should be back to back. Driver will allow
the remote port to complete the process. For the case where
the remote port decide to back off from sending PRLI, this
local port sets an expiration timer for the PRLI. Once the
expiration time passes, the relogin retry logic is allowed
to go through and perform login with the remote port.
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
The main lock that needs to be held for CMD or TMR submission
to upper layer is the sess_lock. The sess_lock is used to
serialize cmd submission and session deletion. The addition
of hardware_lock being held is not necessary. This patch removes
hardware_lock dependency from CMD/TMR submission.
Use hardware_lock only for error response in this case.
Path1
CPU0 CPU1
---- ----
lock(&(&ha->tgt.sess_lock)->rlock);
lock(&(&ha->hardware_lock)->rlock);
lock(&(&ha->tgt.sess_lock)->rlock);
lock(&(&ha->hardware_lock)->rlock);
Path2/deadlock
*** DEADLOCK ***
Call Trace:
dump_stack+0x85/0xc2
print_circular_bug+0x1e3/0x250
__lock_acquire+0x1425/0x1620
lock_acquire+0xbf/0x210
_raw_spin_lock_irqsave+0x53/0x70
qlt_sess_work_fn+0x21d/0x480 [qla2xxx]
process_one_work+0x1f4/0x6e0
Cc: <stable@vger.kernel.org>
Cc: Bart Van Assche <Bart.VanAssche@sandisk.com>
Reported-by: Bart Van Assche <Bart.VanAssche@sandisk.com>
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Normally, ABTS is sent to Target Core as Task MGMT command.
In the case of error, qla2xxx needs to send response, hardware_lock
is required to prevent request queue corruption.
Cc: <stable@vger.kernel.org>
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
When FW notify driver or driver detects low FW resource,
driver tries to send out Busy SCSI Status to tell Initiator
side to back off. During the send process, the lock was not held.
Cc: <stable@vger.kernel.org>
Signed-off-by: Quinn Tran <quinn.tran@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Cc: <stable@vger.kernel.org>
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Cc: <stable@vger.kernel.org>
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Instead of putting cmd_time_out under ../target/core/user_0/foo/control,
which has historically been used by parameters needed for initial
backend device configuration, go ahead and move cmd_time_out into
a backend device attribute.
In order to do this, tcmu_module_init() has been updated to create
a local struct configfs_attribute **tcmu_attrs, that is based upon
the existing passthrough_attrib_attrs along with the new cmd_time_out
attribute. Once **tcm_attrs has been setup, go ahead and point
it at tcmu_ops->tb_dev_attrib_attrs so it's picked up by target-core.
Also following MNC's previous change, ->cmd_time_out is stored in
milliseconds but exposed via configfs in seconds. Also, note this
patch restricts the modification of ->cmd_time_out to before +
after the TCMU device has been configured, but not while it has
active fabric exports.
Cc: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
A single daemon could implement multiple types of devices
using multuple types of real devices that may not support
restarting from crashes and/or handling tcmu timeouts. This
makes the cmd timeout configurable, so handlers that do not
support it can turn if off for now.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This adds a helper to check if the dev was configured. It
will be used in the next patch to prevent updates to some
config settings after the device has been setup.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
This fixes the following races:
1. core_alua_do_transition_tg_pt could have read
tg_pt_gp_alua_access_state and gone into this if chunk:
if (!explicit &&
atomic_read(&tg_pt_gp->tg_pt_gp_alua_access_state) ==
ALUA_ACCESS_STATE_TRANSITION) {
and then core_alua_do_transition_tg_pt_work could update the
state. core_alua_do_transition_tg_pt would then only set
tg_pt_gp_alua_pending_state and the tg_pt_gp_alua_access_state would
not get updated with the second calls state.
2. core_alua_do_transition_tg_pt could be setting
tg_pt_gp_transition_complete while the tg_pt_gp_transition_work
is already completing. core_alua_do_transition_tg_pt then waits on the
completion that will never be called.
To handle these issues, we just call flush_work which will return when
core_alua_do_transition_tg_pt_work has completed so there is no need
to do the complete/wait. And, if core_alua_do_transition_tg_pt_work
was running, instead of trying to sneak in the state change, we just
schedule up another core_alua_do_transition_tg_pt_work call.
Note that this does not handle a possible race where there are multiple
threads call core_alua_do_transition_tg_pt at the same time. I think
we need a mutex in target_tg_pt_gp_alua_access_state_store.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Userspace target_core_user handlers like tcmu-runner may want to set the
ALUA state to transitioning while it does implicit transitions. This
patch allows that state when set from configfs.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
The implicit transition time tells initiators the min time
to wait before timing out a transition. We currently schedule
the transition to occur in tg_pt_gp_implicit_trans_secs
seconds so there is no room for delays. If
core_alua_do_transition_tg_pt_work->core_alua_update_tpg_primary_metadata
needs to write out info to a remote file, then the initiator can
easily time out the operation.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
