| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Many changes all over:
* HE (802.11ax) work continues
* WPA3 offloads
* work on extended key ID handling continues
* fixes to honour AP supported rates with auth/assoc frames
* nl80211 netlink policy improvements to fix some issues
with strict validation on new commands with old attrs
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
>From RTL8168e-vl the value in register MaxTxPacketSize is interpreted
differently, therefore use new helper rtl_is_8168evl_up to set this
register.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add helper rtl_is_8168evl_up to make the code better readable and to
simplify it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There's no rate control algorithm that *doesn't* want to call
it internally, and calling it internally will let us modify
its behaviour in the future.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Require that each vendor command give a policy of its sub-attributes
in NL80211_ATTR_VENDOR_DATA, and then (stricly) check the contents,
including the NLA_F_NESTED flag that we couldn't check on the outer
layer because there we don't know yet.
It is possible to use VENDOR_CMD_RAW_DATA for raw data, but then no
nested data can be given (NLA_F_NESTED flag must be clear) and the
data is just passed as is to the command.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
tp->coalesce_info is used in rtl_coalesce_info() only, so we can
remove this member. In addition replace phy_ethtool_get_link_ksettings
with a direct access to tp->phydev->speed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case of a timeout currently ~0 is returned. Callers often just check
whether a certain bit is set and therefore may behave incorrectly.
So let's return -ETIMEDOUT in case of a timeout.
r8168_phy_ocp_read is used in r8168g_mdio_read only, therefore we can
apply the same change.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We were accessing the pointer returned from platform_get_resource before
checking if it was valid, causing an oops if it was not. Move this access
after the call to devm_ioremap_resource which does the validity check.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We statically allocate 8 cmd buffers on the read channel, when the only
IO left that's still using them is the long-running READ.
Replace this with a single allocated cmd, that gets restarted whenever
the READ completed.
This introduces refcounting for allocated cmds, so that the READ cmd can
survive the IO completion.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current IDX sequence first sends one WRITE cmd to activate the
device, and then sends a second cmd that READs the response.
Using qeth_alloc_cmd(), we can combine this into a single IO with two
command-chained CCWs.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The RCD code is the last remaining IO path that doesn't use the
qeth_send_control_data() infrastructure. Doing so allows us to remove
all sorts of custom state machinery and logic in the IRQ handler.
Instead of introducing statically allocated cmd buffers for this single
IO on the data channel, use the new qeth_alloc_cmd() helper.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
qeth currently uses a fixed set of statically allocated cmd buffers for
the read and write IO channels. This (1) doesn't play well with the single
RCD cmd we need to issue on the data channel, (2) doesn't provide the
necessary flexibility for certain IDX improvements, and (3) is also rather
wasteful since the buffers are idle most of the time.
Add a new type of cmd buffer that is dynamically allocated, and keeps
its ccw chain in the DMA data area. Since this touches most callers of
qeth_setup_ccw(), also add a new CCW flags parameter for future usage.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Each cmd buffer maintains a pointer to the IO channel that it was/will
be issued on. So when dealing with cmd buffers, we don't need to pass
around a separate channel pointer.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The vast majority of SETUP-classified trace entries can be moved to
their device-specific trace file. This reduces pollution of the global
SETUP file, and provides a consistent trace view of all activity on the
device.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
OSN currently provides a custom code path to submit IPA cmds, without
waiting for the cmd response. Replace it with qeth_send_ipa_cmd(), which
uses the common qeth_send_control_data() IO infrastructure.
By setting a custom iob->callback, we can now provide feedback to the
caller about whether the cmd has been successfully submitted to HW.
Since the callback then immediately wakes up the reply-waiter object, we
maintain the old behaviour of returning early without waiting for the
response.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The basic MPC initialization sequence is strictly sequential, and
waiting for an available cmd buffer should never be necessary.
So this change only affects the OSN path, where dangling waiters on an
unbounded wait_event() are not desirable. Switch to qeth_get_buffers(),
and let OSN callers deal with -ENOMEM.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When called from qeth_core_probe_device(), qeth_determine_capabilities()
initializes the device's BLKT defaults. From all other callers, the
ccw_device has already been set online and the BLKT setting is skipped.
Clean this up by extracting the BLKT setting into a separate helper that
gets called from the right place.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The completion of a pending READ cmd is processed via
qeth_issue_next_read_cb(). Let this callback also start the next READ
cmd, instead of hardcoding that step into the IRQ handler.
While at it remove the check of the channel state,
__qeth_issue_next_read() already does this.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the tear down sequence in qeth_l?_stop_card() has finished, the
card is guaranteed to be in DOWN state and we don't have to check for
it again.
With this insight we can also remove the redundant setting of
card->state in qeth_l?_set_online()'s error path.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Slightly reduce the complexity of the core xmit path, by replacing some
open-coded logic with the corresponding helpers.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Current code suppresses debug entries when an TX buffer completes in
ERROR state with no error indication set in SBALF15.
This was introduced back with
commit 58490f18071d ("qeth: HiperSockets SIGA retry support on CC=2.").
But qeth no longer retries after CC=2, and this sort of suppression
make no sense anymore. Remove it.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Initialize the PTP physical hardware clock.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement physical hardware clock operations.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Publish scaled_ppm_to_ppb to allow drivers to use it.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The MTPPS register provides the device PPS capabilities, configure the PPS
in and out modules and holds the PPS in time stamp.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The MTUTC register configures the HW UTC counter.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Query free running clock PCI BAR and offsets during the pci_init.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add two new bus operations for reading the hardware free running clock.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add free running clock PCI BAR and offset to query firmware command.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Convert everything to phylink.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Start adding the phylink callbacks.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation for the convertion, split the adjust_link function into
mac_config and add the mac_link_up and mac_link_down functions.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix sparse warning:
drivers/net/ethernet/qlogic/qede/qede_main.c:963:6:
warning: symbol 'qede_lock' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qede/qede_main.c:969:6:
warning: symbol 'qede_unlock' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix sparse warnings:
drivers/net/dsa/sja1105/sja1105_main.c:1848:6:
warning: symbol 'sja1105_port_rxtstamp' was not declared. Should it be static?
drivers/net/dsa/sja1105/sja1105_main.c:1869:6:
warning: symbol 'sja1105_port_txtstamp' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Report devlink health on FW fatal issues via fw_fatal_reporter. The
driver recover flow for FW fatal error is now being handled by the
devlink health.
Having the recovery controlled by devlink health, the user has the
ability to cancel the auto-recovery for debug session and run it
manually.
Call mlx5_enter_error_state() before calling devlink_health_report() to
ensure entering device error state even if auto-recovery is off.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Add support of dump callback for mlx5 FW fatal reporter.
The FW fatal dump uses cr-dump functionality to gather cr-space data for
debug. The cr-dump uses vsc interface which is valid even if the FW
command interface is not functional, which is the case in most FW fatal
errors.
Command example and output:
$ devlink health dump show pci/0000:82:00.0 reporter fw_fatal
crdump_data:
00 20 00 01 00 00 00 00 03 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 80
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 ba 82 00 00
0c 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20
00 00 00 00 00 00 00 00 00 00 00 00 00 00 fa 00
a4 0e 00 00 00 00 00 00 80 c7 fe ff 50 0a 00 00
...
...
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Create mlx5_devlink_health_reporter for fw fatal reporter.
The fw fatal reporter is added in addition to the fw reporter and
implements the recover callback.
The point of having two reporters for FW issues, is that we
don't want to run FW recover on any issue, but only fatal ones.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Use devlink_health_report() to report any symptom of FW issue as FW
counter miss or new health syndrome.
The FW issues detected in mlx5 during poll_health which is called in
timer atomic context and so health work queue is used to schedule the
reports.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Add support of dump callback for mlx5 FW reporter. Once we trigger FW
dump, the FW will write the core dump to its raw data buffer. The tracer
translates the raw data to traces and save it to a cyclic array. Once
dump is done, the saved traces data is filled into the dump buffer. In
case syndrome is not zero the health buffer content will be printed as
well.
FW dump example:
$ devlink health dump show pci/0000:82:00.0 reporter fw
dump fw traces:
timestamp: 509006640427 lost: false event_id: 185 msg: dump general
info GVMI=0x0000
timestamp: 509006645474 lost: false event_id: 185 msg: GVMI
management info, gvmi_management context:
timestamp: 509006654463 lost: false event_id: 185 msg: [000]:
00000000 00000000 00000000 00000000
timestamp: 509006656127 lost: false event_id: 185 msg: [010]:
00000000 00000000 00000000 00000000
timestamp: 509006656255 lost: false event_id: 185 msg: [020]:
00000000 00000000 00000000 00000000
timestamp: 509006656511 lost: false event_id: 185 msg: [030]:
00000000 00000000 00000000 00000000
timestamp: 509006656639 lost: false event_id: 185 msg: [040]:
00000000 00000000 00000000 00000000
timestamp: 509006656895 lost: false event_id: 185 msg: [050]:
00000000 00000000 00000000 00000000
timestamp: 509006657023 lost: false event_id: 185 msg: [060]:
00000000 00000000 00000000 00000000
timestamp: 509006657180 lost: false event_id: 185 msg: [070]:
00000000 00000000 00000000 00000000
timestamp: 509006659839 lost: false event_id: 185 msg: CMDIF dbase
from IRON: active_dbase_slots = 0x00000000
timestamp: 509006667391 lost: false event_id: 185 msg: GVMI=0x0000
hw_toc context:
timestamp: 509006667647 lost: false event_id: 185 msg: [000]:
00000000 00000000 00000000 fffff000
timestamp: 509006667775 lost: false event_id: 185 msg: [010]:
00000000 00000000 00000000 80d00000
...
...
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Create mlx5_devlink_health_reporter for FW reporter. The FW reporter
implements devlink_health_reporter diagnose callback.
The fw reporter diagnose command can be triggered any time by the user
to check current fw status.
In healthy status, it will return clear syndrome. Otherwise it will
return the syndrome and description of the error type.
Command example and output on healthy status:
$ devlink health diagnose pci/0000:82:00.0 reporter fw
Syndrome: 0
Command example and output on non healthy status:
$ devlink health diagnose pci/0000:82:00.0 reporter fw
Syndrome: 8 Description: unrecoverable hardware error
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
If a FW assert is considered fatal, indicated by a new bit in the health
buffer, reset the FW. After the reset go through the normal recovery
flow. Only one PF needs to issue the reset, so an attempt is made to
prevent the 2nd function from also issuing the reset.
It's not an error if that happens, it just slows recovery.
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Since the FW can be shared between different PFs/VFs it is common
that more than one health poll will detected a failure, this can
lead to multiple resets which are unneeded.
The solution is to use a FW locking mechanism using semaphore space
to provide a way to allow only one device to collect the cr-dump and
to issue a sw-reset.
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
New mlx5 adapters allow the driver to reset the FW in the event of an
error, this action called "SW Reset". When an SW reset is issued on any
PF all PFs enter reset state which is a recoverable condition. The
existing recovery flow was designed to allow the recovery of a VF after
a PF driver reload. This patch adds the sw reset to the NIC states
as a preparation for sw reset handling.
When a software reset is issued the following occurs:
1. The NIC interface mode is set to 7 while the reset is in progress.
2. Once the reset completes the NIC interface mode is set to 1.
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Reviewed-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Crdump allows the driver to retrieve a dump of the FW PCI crspace.
This is useful in case of catastrophic issues which may require FW
reset. The crspace dump can be used for later debug.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Reviewed-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The Vendor Specific Capability (VSC) is used to activate a gateway
interfacing with the device. The gateway is used to read or write
device configurations, which are organized in different domains (spaces).
A configuration access may result in multiple actions, reads, writes.
Example usages are accessing the Crspace domain to read the crspace or
locking a device semaphore using the Semaphore domain.
The configuration access use pci_cfg_access to prevent parallel access to
the VSC space by the driver and userspace calls.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Centralize all devlink related callbacks in one file.
In the downstream patch, some more functionality will be added, this
patch is preparing the driver infrastructure for it.
Currently, move devlink un/register functions calls into this file.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Update driver version to match device specification.
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Let the compiler decide if the function should be inline in *.c files
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement the set_ringparam() function of the ethtool interface
to enable the changing of io queue sizes.
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If there is not enough memory to allocate io queues the driver will
try to allocate smaller queues.
The backoff algorithm is as follows:
1. Try to allocate TX and RX and if successful.
1.1. return success
2. Divide by 2 the size of the larger of RX and TX queues (or both if their size is the same).
3. If TX or RX is smaller than 256
3.1. return failure.
4. else
4.1. go back to 1.
Also change the tx_queue_size, rx_queue_size field names in struct
adapter to requested_tx_queue_size and requested_rx_queue_size, and
use RX and TX queue 0 for actual queue sizes.
Explanation:
The original fields were useless as they were simply used to assign
values once from them to each of the queues in the adapter in ena_probe().
They could simply be deleted. However now that we have a backoff
feature, we have use for them. In case of backoff there is a difference
between the requested queue sizes and the actual sizes. Therefore there
is a need to save the requested queue size for future retries of queue
allocation (for example if allocation failed and then ifdown + ifup was
called we want to start the allocation from the original requested size of
the queues).
Signed-off-by: Arthur Kiyanovski <akiyano@amazon.com>
Signed-off-by: Sameeh Jubran <sameehj@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
