| Age | Commit message (Collapse) | Author |
|---|
|
The SBCM register configures the shared buffer configuration according
to port and TC. So far all pools have had a dynamic size, where the
infinite size is easy to express by using max_buff of 0xff. However the
MC pool should be configured with static size, and the infinite size
thus needs to be set using the field SBCM.infi_max.
Therefore add the field infi_max to the SBCM register and to
mlxsw_reg_sbcm_pack(). Extend mlxsw_sp_sb_cm_write() to handle infinite
sizes as well. Report infinite pool limits as if the limit actually were
the total shared buffer size.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The MC pool should have an infinite size (i.e. no quota).
To that end, add infi_size to the SBPR register and extend
mlxsw_reg_sbpr_pack(). Also add MLXSW_SP_SB_INFI to denote
buffers that should have an infinite size.
Change mlxsw_sp_sb_pr_write() to take as parameter byte size,
instead of cell size, and add the special handling of infinite
buffers. Report pools with infinite size as if they actually
take the full shared buffer size.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Entities of infinite size will be reported as if they had the maximum
size allowed by the chip. To that end, keep track of maximum shared
buffer size in mlxsw_sp->sb.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Current code assumes that ingress and egress has the same number of
traffic classes. Since the introduction of MC-aware mode that assumption
hasn't held anymore, and there have been 16 TCs on the egress as opposed
to 8 on ingress.
Break the assumption of symmetry by splitting the artifacts related to
shared-buffer TC counting to ingress and egress parts.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, mlxsw assumes that each ingress pool has its egress
counterpart, and that pool index for purposes of caching matches the
index with which the hardware should be configured. As we want to expose
the MC pool, both of these assumptions break.
Instead, maintain the pool index as long as possible. Unify ingress and
egress caches and use the pool index as cache index as well. Only
translate to FW pool numbering when actually packing the registers. This
simplifies things considerably, as the pool index is the only quantity
necessary to uniquely identify a pool, and the pool/direction split is
not necessary until firmware is talked to.
To support the mapping between pool indices and pool numbers and
directions, which is not neatly mathematical anymore, introduce a pool
descriptor table, indexed by pool index, to facilitate the translation.
Include the MC pool in the descriptor table as well, so that it can be
referenced from mlxsw_sp_sb_cms_egress.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With introduction of MC-aware mode to mlxsw, it became necessary to
configure TCs above 7 as well. There is now code in mlxsw to disable ETS
for these higher classes, but disablement of max shaper was neglected.
By default, max shaper is currently disabled to begin with, so the
problem is just cosmetic. However, for symmetry, do like we do for ETS
configuration, and call mlxsw_sp_port_ets_maxrate_set() for both TC i
and i + 8.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Clang warns when more than one set of parentheses are used for single
conditional statements:
drivers/isdn/hisax/w6692.c:627:30: warning: equality comparison with
extraneous parentheses [-Wparentheses-equality]
if ((cs->dc.w6692.ph_state == W_L1IND_DRD)) {
~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~
drivers/isdn/hisax/w6692.c:627:30: note: remove extraneous parentheses
around the comparison to silence this warning
if ((cs->dc.w6692.ph_state == W_L1IND_DRD)) {
~ ^ ~
drivers/isdn/hisax/w6692.c:627:30: note: use '=' to turn this equality
comparison into an assignment
if ((cs->dc.w6692.ph_state == W_L1IND_DRD)) {
^~
=
1 warning generated.
Remove the parentheses to silence this warning.
Reported-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/atheros/atlx/atl1.c: In function 'atl1_set_link_ksettings':
drivers/net/ethernet/atheros/atlx/atl1.c:3280:6: warning:
variable 'advertising' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/intel/e1000/e1000_main.c: In function 'e1000_watchdog':
drivers/net/ethernet/intel/e1000/e1000_main.c:2436:9: warning:
variable 'txb2b' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The local variable 'index_specified' is never used after being assigned.
hence it should be redundant adn can be removed.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
NFP supports fairly enormous ring sizes (up to 256k descriptors).
In commit 466271703867 ("nfp: use kvcalloc() to allocate SW buffer
descriptor arrays") we have started using kvcalloc() functions to
make sure the allocation of software state arrays doesn't hit
the MAX_ORDER limit. Unfortunately, we can't use virtual mappings
for the DMA region holding HW descriptors. In case this allocation
fails instead of the generic (and fairly scary) warning/splat in
the logs print a helpful message explaining what happened and
suggesting how to fix it.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Setting register 0x82 to value 01 is done a few lines before for all
chip versions <= 06 anyway. And setting PHY register 0x0b to value 00
is done at the end of rtl8169s_hw_phy_config() already. So we can
remove this.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
PCI_LATENCY_TIMER is ignored on PCIe, therefore we have to do this
for the PCI chips (version <= 06) only. Also we can move setting
PCI_CACHE_LINE_SIZE.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
That local variable are never used after being assigned.
hence it should be redundant and can be removed.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The local variable 'k' is never used after being assigned.
hence it should be redundant adn can be removed.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
So far all the places calling hclge_tm_q_to_qs_map_cfg() are assigning
an u16 type value to "q_id", and in the processing of
hclge_tm_q_to_qs_map_cfg(), it also converts the "q_id" to le16.
The max tqp number for pf can be more than 256, we should use "u16" to
store the queue id, instead of "u8", which may cause data lost.
Fixes: 848440544b41 ("net: hns3: Add support of TX Scheduler & Shaper to HNS3 driver")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When roce is loaded before nic, the roce client will not be initialized
until nic client is initialized, but roce init flag is set before it.
Furthermore, in this case of nic initialized success and roce failed,
the nic init flag is not set, and roce init flag is not cleared.
This patch fixes it by set init flag only after the client is initialized
successfully.
Fixes: e2cb1dec9779 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Fixes: 46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
finished
If initialize client failed or finish uninitializing client, we should
clear the client pointer. It may cause unexpected result when use
uninitialized client. Meanwhile, we also should check whether client
exist when uninitialize it.
Fixes: 46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
According to hardware's description, the head pointer register should
be written before the tail pointer register while initializing the vf
command queue. Otherwise, it may trigger an interrupt even though there
is no command received.
Fixes: fedd0c15d288 ("net: hns3: Add HNS3 VF IMP(Integrated Management Proc) cmd interface")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The function of genphy_read_status is that reading phy information
from HW and using these information to update SW variable. If user
is using ethtool to setting the speed of phy and service task is calling
by hclge_get_mac_phy_link, the result of speed setting is uncertain.
Because ethtool cmd will modified phydev and hclge_get_mac_phy_link also
will modified phydev.
Because phy state machine will update phy link periodically, we can
just use phydev->link to check the link status. This patch removes
function call of genphy_read_status. To ensure accuracy, this patch
adds a phy state check. If phy state is not PHY_RUNNING, we consider
link is down. Because in some scenarios, phydev->link may be link up,
but phy state is not PHY_RUNNING. This is just an intermediate state.
In fact, the link is not ready yet.
Fixes: 46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
By default, HW link status is up. If hclge_update_link_status is called
before net up, driver will print "link up". It is not suitable. hdev
state check is needed when getting link status.
Fixes: 46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Fixes: e2cb1dec9779 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We clear STATE_DOWN bit of hdev state when starting net, but do not set
it again when stopping net. It causes that the net is down, but hdev state
is still up. STATE_DOWN bit of hdev state should be set when stopping net.
Fixes: 46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Fixes: e2cb1dec9779 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the .ndo_do_ioctl net_device_ops operation to support
the PHY MII ioctl for PF driver.
Fixes: 76ad4f0ee747 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Xi Wang <wangxi11@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All pf have permission to read packet statistics of public in hardware,
but the read operation will clear registers which cause statistical
inaccuracy.
This patch removes all packet statistics of public.
Signed-off-by: Junxin Chen <chenjunxin1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The the actual Tx work is minimal, driver can clean up as more
Tx descriptors as possible in a irq.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds unlikely for buf_num check.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All irq will float to cpu0 if do not set irq affinity.
This patch adds default irq affinity in hns3 driver, users can
also change the irq affinity in OS.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, but the implementation in this
driver returns an 'int'.
Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Shannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.
Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.
Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.
Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.
Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t',
which is a typedef for an enum type, so make sure the implementation in
this driver has returns 'netdev_tx_t' value, and change the function
return type to netdev_tx_t.
Found by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch removes the explicit call to netif_carrier_off() in
mvneta_open() as this is already handled in phylink_start().
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch removes the explicit call to netif_carrier_off() in PPv2's
open() path, as this is now handled in phylink_start().
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Phylink made an assumption about the carrier state being down when
calling phylink_start(). If this assumption isn't satisfied, the
internal phylink state could misbehave and a net device could end up not
being functional.
This patch fixes this by explicitly calling netif_carrier_off() in
phylink_start().
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As the mvpp2_percpu_read/write/... functions aren't really per-cpu but
per s/w thread, rename them to include 'thread' instead of 'percpu'.
This is a cosmetic patch.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Marvell PPv2 network controller has 9 internal threads. The driver
works fine when there are less CPUs available than threads. This isn't
true if more CPUs are available. As this is a valid use case, handle
this particular case.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch maps all uses of the CPU to threads. All this_cpu calls are
replaced, and all smp_processor_id() calls are wrapped into the
indirection.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch reworks the Marvell PPv2 driver to stop using directly the
CPU number to access per-thread registers.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the Marvell PPv2 driver the mvpp2_read_relaxed function is only used
in a single file. Make it static and remove its prototype from the
header.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Marvell PPv2 driver has per-cpu functions. As they only are used in
the main file, make them static and remove their prototype from the
header.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Updates the PPv2 driver so that all CPU variables are unsigned, as it
makes no sense to have a negative CPU number. This patch is cosmetic.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Marvell PPv2.2 engine only has 8 Rx queues per CPU, while PPv2.1 has
16 of them. This patch updates the code so that the Rx queues mask width
is selected given the version of the network controller used.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch updates the probing function so that the queue mode isn't
updated while probing, as the driver would silently end up using a
configuration not wanted by the user. The patch adds an extra check to
validate the chosen queue mode instead, and the driver will fail to
probe if the configuration is invalid.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch renames the IRQs in the Marvell PPv2 driver as their current
names match the way they are used in software. But this will change in
the future, and those IRQs have nothing to do with Rx/Tx interrupts
(this can be configured). The new binding also describe more interrupts
as some where left out.
The old binding support is kept for backward compatibility.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch sets the number of s/w threads to 9, its maximum value,
instead of 8. This is not a fix as only 4 of the s/w threads were used
so far, but more could be used in the future.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch sets from two descriptor to one descriptor because R-Car Gen3
does not have the 4 bytes alignment restriction of the transmission buffer.
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
phy_stop() may be called e.g. when suspending, therefore all needed
actions should be performed synchronously. Therefore add a synchronous
call to the state machine.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
FIELD_SIZEOF is defined as a macro to calculate the specified value. Therefore,
We prefer to use the macro rather than calculating its value.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
