summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2020-05-31ice: Increase timeout after PFRDan Nowlin
To allow for resets during package download, increase the timeout period after performing a PFR. The time waited is the global config lock timeout plus the normal PFSWR timeout. Signed-off-by: Dan Nowlin <dan.nowlin@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2020-05-31ice: Fix transmit for all software offloaded VLANsBrett Creeley
Currently the driver does not recognize when there is an 802.1AD VLAN tag right after the dmac/smac (outermost VLAN tag). If any DCB map is applied and/or DCB is enabled this is causing the hardware to insert a VLAN 0 tag after the 802.1AD VLAN tag that is already in the packet. Fix this by preventing VLAN tag 0 from being added when any VLAN is already present after dmac/smac (software offloaded) or skb (hardware offloaded). Signed-off-by: Brett Creeley <brett.creeley@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2020-05-31ice: support adding 16 unicast/multicast filter on untrusted VFPaul Greenwalt
Allow untrusted VF to add 16 unicast/multicast filters. VF uses 1 filter for the default/perm_addr/LAA MAC, 1 for broadcast, and 16 additional unicast/multicast filters. Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2020-05-31ice: allow host to clear administratively set VF MACBrett Creeley
Currently a user is not allowed to clear a VF's administratively set MAC on the PF. Fix this by allowing an all zero MAC address via "ip link set ${pf_eth} vf ${vf_id} mac 00:00:00:00:00:00". An example use case for this would be issuing a "virsh shutdown" command on a VM. The call to iproute mentioned above is part of this flow. Without this change the driver incorrectly rejects clearing the VF's administratively set MAC and prints unhelpful log messages. Also, improve the comments surrounding this change. Signed-off-by: Brett Creeley <brett.creeley@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2020-05-30ravb: Mask PHY mode to avoid inserting delays twiceGeert Uytterhoeven
Until recently, the Micrel KSZ9031 PHY driver ignored any PHY mode ("RGMII-*ID") settings, but used the hardware defaults, augmented by explicit configuration of individual skew values using the "*-skew-ps" DT properties. The lack of PHY mode support was compensated by the EtherAVB MAC driver, which configures TX and/or RX internal delay itself, based on the PHY mode. However, now the KSZ9031 driver has gained PHY mode support, delays may be configured twice, causing regressions. E.g. on the Renesas Salvator-X board with R-Car M3-W ES1.0, TX performance dropped from ca. 400 Mbps to 0.1-0.3 Mbps, as measured by nuttcp. As internal delay configuration supported by the KSZ9031 PHY is too limited for some use cases, the ability to configure MAC internal delay is deemed useful and necessary. Hence a proper fix would involve splitting internal delay configuration in two parts, one for the PHY, and one for the MAC. However, this would require adding new DT properties, thus breaking DTB backwards-compatibility. Hence fix the regression in a backwards-compatibility way, by letting the EtherAVB driver mask the PHY mode when it has inserted a delay, to avoid the PHY driver adding a second delay. This also fixes messages like: Micrel KSZ9031 Gigabit PHY e6800000.ethernet-ffffffff:00: *-skew-ps values should be used only with phy-mode = "rgmii" as the PHY no longer sees the original RGMII-*ID mode. Solving the issue by splitting configuration in two parts can be handled in future patches, and would require retaining a backwards-compatibility mode anyway. Fixes: bcf3440c6dd78bfe ("net: phy: micrel: add phy-mode support for the KSZ9031 PHY") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-30vxlan: few locking fixes in nexthop event handlerRoopa Prabhu
- remove fdb from nh_list before the rcu grace period - protect fdb->vdev with rcu - hold spin lock before destroying fdb Fixes: c7cdbe2efc40 ("vxlan: support for nexthop notifiers") Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-30vxlan: add check to prevent use of remote ip attributes with NDA_NH_IDRoopa Prabhu
NDA_NH_ID represents a remote ip or a group of remote ips. It allows use of nexthop groups in lieu of a remote ip or a list of remote ips supported by the fdb api. Current code ignores the other remote ip attrs when NDA_NH_ID is specified. In the spirit of strict checking, This commit adds a check to explicitly return an error on incorrect usage. Fixes: 1274e1cc4226 ("vxlan: ecmp support for mac fdb entries") Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-30Merge branch '100GbE' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue Jeff Kirsher says: ==================== 100GbE Intel Wired LAN Driver Updates 2020-05-28 This series contains updates to the ice driver only. Anirudh (Ani) adds a poll for reset completion before proceeding with driver initialization when the DDP package fails to load and the firmware issues a core reset. Jake cleans up unnecessary code, since ice_set_dflt_vsi_ctx() performs a memset to clear the info from the context structures. Fixed a potential double free during probe unrolling after a failure. Also fixed a potential NULL pointer dereference upon register_netdev() failure. Tony makes two functions static which are not called outside of their file. Brett refactors the ice_ena_vf_mappings(), which was doing the VF's MSIx and queue mapping in one function which was hard to digest. So create a new function to handle the enabling MSIx mappings and another function to handle the enabling of queue mappings. Simplify the code flow in ice_sriov_configure(). Created a helper function for clearing VPGEN_VFRTRIG register, as this needs to be done on reset to notify the VF that we are done resetting it. Fixed the initialization/creation and reset flows, which was unnecessarily complicated, so separate the two flows into their own functions. Renamed VF initialization functions to make it more clear what they do and why. Added functionality to set the VF trust mode bit on reset. Added helper functions to rebuild the VLAN and MAC configurations when resetting a VF. Refactored how the VF reset is handled to prevent VF reset timeouts. Paul cleaned up code not needed during a CORER/GLOBR reset. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-30r8169: improve handling power management opsHeiner Kallweit
Simplify handling the power management callbacks. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-30r8169: make rtl8169_down central chip quiesce functionHeiner Kallweit
Functionality for quiescing the chip is spread across different functions currently. Move it to rtl8169_down(). Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-30r8169: move some calls to rtl8169_hw_resetHeiner Kallweit
Move calls that are needed before and after calling rtl8169_hw_reset() into this function. This requires to move the function in the code. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-30r8169: don't reset tx ring indexes in rtl8169_tx_clearHeiner Kallweit
In places where the indexes have to be reset, we call rtl8169_init_ring_indexes() anyway after rtl8169_tx_clear(). Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-30r8169: enable WAKE_PHY as only WoL source when runtime-suspendingHeiner Kallweit
We go to runtime-suspend few secs after cable removal. As cable is removed "physical link up" is the only meaningful WoL source. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-30r8169: change driver data typeHeiner Kallweit
Change driver private data type to struct rtl8169_private * to avoid some overhead. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-30Merge tag 'wireless-drivers-next-2020-05-30' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next Kalle Valo says: ==================== wireless-drivers-next patches for v5.8 Third set of patches for v5.8. Final new features before the merge window (most likely) opens, noteworthy here is adding WPA3 support to old drivers rt2800, b43 and b43_legacy. Major changes: ath10k * SDIO and SNOC busses are not experimental anymore ath9k * allow receive of broadcast Action frames ath9k_htc * allow receive of broadcast Action frames rt2800 * enable WPA3 support out of box b43 * enable WPA3 support b43_legacy * enable WPA3 support mwifiex * advertise max number of clients to user space mt76 * mt7663: add remain-on-channel support * mt7915: add spatial reuse support * add support for mt7611n hardware iwlwifi * add ACPI DSM support * support enabling 5.2GHz bands in Indonesia via ACPI * bump FW API version to 56 ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-30net: dsa: sja1105: fix port mirroring for P/Q/R/SVladimir Oltean
The dynamic configuration interface for the General Params and the L2 Lookup Params tables was copy-pasted between E/T devices and P/Q/R/S devices. Nonetheless, these interfaces are bitwise different. The driver is using dynamic reconfiguration of the General Parameters table for the port mirroring feature, which was therefore broken on P/Q/R/S. Note that this patch can't be backported easily very far to stable trees (since it conflicts with some other development done since the introduction of the driver). So the Fixes: tag is purely informational. Fixes: 8aa9ebccae87 ("net: dsa: Introduce driver for NXP SJA1105 5-port L2 switch") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-30net: dsa: sja1105: suppress -Wmissing-prototypes in sja1105_static_config.cVladimir Oltean
Newer compilers complain with W=1 builds that there are non-static functions defined in sja1105_static_config.c that don't have a prototype, because their prototype is defined in sja1105.h which this translation unit does not include. I don't entirely understand what is the point of these warnings, since in principle there's nothing wrong with that. But let's move the prototypes to a header file that _is_ included by sja1105_static_config.c, since that will make these warnings go away. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-30Merge tag 'mlx5-cleanup-2020-05-29' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux Saeed Mahameed says: ==================== mlx5-cleanup-2020-05-29 Accumulated cleanup patches and sparse warning fixes for mlx5 driver. 1) sync with mlx5-next branch 2) Eli Cohen declares mpls_entry_encode() helper in mpls.h as suggested by Jakub Kicinski and David Ahern, and use it in mlx5 3) Jesper Fixes xdp data_meta setup in mlx5 4) Many sparse and build warnings cleanup ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-30net: hns3: remove some unused codes in hns3_nic_set_features()Huazhong Tan
NETIF_F_HW_VLAN_CTAG_FILTER is not set in netdev->hw_feature for the HNS3 driver, so the handler of NETIF_F_HW_VLAN_CTAG_FILTER in hns3_nic_set_features() won't be called, remove it. Reported-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-30net: hns3: fix two coding style issues in hclgevf_main.cHuazhong Tan
Remove a redundant blank line in hclgevf_cmd_set_promisc_mode(), and fix a reverse xmas tree coding style issue in hclgevf_set_rss_tc_mode(). Reported-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-30net: hns3: fix an incorrect comment for num_tqps in struct hclgevf_devHuazhong Tan
struct hclgevf_dev stands for VF device, its field num_tqps indicates the number of VF's task queue pairs, so the comment is incorrect, replace 'PF' with 'VF'. Reported-by: Jian Shen <shenjian15@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-30net: hns3: remove two unused macros in hclgevf_cmd.cHuazhong Tan
Macro hclgevf_ring_to_dma_dir and hclgevf_is_csq defined in hclgevf_cmd.c, but not used, so remove them. Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-30net: hns3: remove an unused macro hclge_is_csqHuazhong Tan
Macro hclge_is_csq defined in hcgle_cmd.c has not been used, so remove it. Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-30net: hns3: fix a print format issue in hclge_mac_mdio_config()Huazhong Tan
Use %d to print int variable 'ret' in hclge_mac_mdio_config(). Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-30Merge ath-next from git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/ath.gitKalle Valo
ath.git patches for v5.8. Major changes: ath9k * allow receive of broadcast Action frames ath9k_htc * allow receive of broadcast Action frames
2020-05-30ath11k: clear DCM max constellation tx valueMuna Sinada
According to 11ax spec. draft 4.0. DCM Max Constellation Tx data field should be set to "Reserved" for an AP, therefore bit is cleared. Signed-off-by: Muna Sinada <msinada@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/1590707417-29672-1-git-send-email-msinada@codeaurora.org
2020-05-30ath11k: reset trigger frame MAC padding durationMuna Sinada
The value was 3 and it's reserved value. Corrected to maintain fw defaults. Signed-off-by: Muna Sinada <msinada@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/1590706483-27609-1-git-send-email-msinada@codeaurora.org
2020-05-30ath10k: Remove ath10k_qmi_register_service_notifier() declarationDouglas Anderson
The ath10k/qmi.h header file contains a declaration for the function ath10k_qmi_register_service_notifier(). This function doesn't exist. Remove the declaration. This patch is a no-op and was just found by code inspection. Fixes: ba94c753ccb4 ("ath10k: add QMI message handshake for wcn3990 client") Signed-off-by: Douglas Anderson <dianders@chromium.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200528122105.1.I31937dce728b441fd72cbe23447bc4710fd56ddb@changeid
2020-05-30ath9k_htc: Set RX filter based to allow broadcast Action frame RXJouni Malinen
Advertise support for multicast frame registration and update the RX filter based on the recently added FIF_MCAST_ACTION to allow broadcast Action frames to be received. This is needed for Device Provisioning Protocol (DPP) use cases that use broadcast Public Action frames. Signed-off-by: Jouni Malinen <jouni@codeaurora.org> Reported-by: kbuild test robot <lkp@intel.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200426084733.7889-2-jouni@codeaurora.org
2020-05-30ath9k: Set RX filter based to allow broadcast Action frame RXJouni Malinen
Advertise support for multicast frame registration and update the RX filter based on the recently added FIF_MCAST_ACTION to allow broadcast Action frames to be received. This is needed for Device Provisioning Protocol (DPP) use cases that use broadcast Public Action frames. Signed-off-by: Jouni Malinen <jouni@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200426084733.7889-1-jouni@codeaurora.org
2020-05-29net/mlx5e: Make mlx5e_dcbnl_ops staticSaeed Mahameed
Fix sparse warning: drivers/net/ethernet/mellanox/mlx5/core/en_dcbnl.c:988:29: error: symbol 'mlx5e_dcbnl_ops' was not declared. Should it be static? Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2020-05-29net/mlx5e: en_tc: Fix cast to restricted __be32 warningSaeed Mahameed
Fixes sparse warnings: warning: cast to restricted __be32 warning: restricted __be32 degrades to integer Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Reviewed-by: Mark Bloch <markb@mellanox.com>
2020-05-29net/mlx5e: en_tc: Fix incorrect type in initializer warningsSaeed Mahameed
Fix some trivial warnings of the type: warning: incorrect type in initializer (different base types) Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Reviewed-by: Mark Bloch <markb@mellanox.com>
2020-05-29net/mlx5: Accel: fpga tls fix cast to __be64 and incorrect argument typesSaeed Mahameed
tls handle and rcd_sn are actually big endian and not in host format. Fix that. Fix the following sparse warnings: drivers/net/ethernet/mellanox/mlx5/core/en_accel/tls.c:177:21: warning: cast to restricted __be64 drivers/net/ethernet/mellanox/mlx5/core/en_accel/tls.c:178:52: warning: incorrect type in argument 2 (different base types) expected unsigned int [usertype] handle got restricted __be32 [usertype] handle Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2020-05-29net/mlx5: cmd: Fix memset with byte count warningSaeed Mahameed
Fix sparse warning: drivers/net/ethernet/mellanox/mlx5/core/cmd.c:1949:15: warning: memset with byte count of 271720 mlx5_cmd_stats array is too big to be held inline in mlx5_cmd. Allocate it separately. Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2020-05-29net/mlx5: DR: Fix incorrect type in return expressionSaeed Mahameed
dr_ste_crc32_calc() calculates crc32 and should return it in HW format. It is being used to calculate a u32 index, hence we force the return value of u32 to avoid the sparse warning: drivers/net/ethernet/mellanox/mlx5/core/steering/dr_ste.c:115:16: warning: incorrect type in return expression (different base types) expected unsigned int got restricted __be32 [usertype] Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Reviewed-by: Mark Bloch <markb@mellanox.com>
2020-05-29net/mlx5: DR: Fix cast to restricted __be32Saeed Mahameed
raw_ip actual type is __be32 and not u32. Fix that and get rid of the warning. drivers/net/ethernet/mellanox/mlx5/core/steering/dr_ste.c:906:31: warning: cast to restricted __be32 Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Reviewed-by: Mark Bloch <markb@mellanox.com>
2020-05-29net/mlx5: DR: Fix incorrect type in argumentSaeed Mahameed
HW spec objects should receive a void ptr to work on, the MLX5_SET/GET macro will know how to handle it. No need to provide explicit or wrong pointer type in this case. warning: incorrect type in argument 1 (different base types) expected unsigned long long const [usertype] *sw_action got restricted __be64 [usertype] *[assigned] sw_action Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Reviewed-by: Mark Bloch <markb@mellanox.com>
2020-05-29net/mlx5e: Use generic API to build MPLS labelEli Cohen
Make use of generic API mpls_entry_encode() to build mpls label and get rid of local function. Signed-off-by: Eli Cohen <eli@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2020-05-29net/mlx5: reduce stack usage in qp_read_fieldArnd Bergmann
Moving the mlx5_ifc_query_qp_out_bits structure on the stack was a bit excessive and now causes the compiler to complain on 32-bit architectures: drivers/net/ethernet/mellanox/mlx5/core/debugfs.c: In function 'qp_read_field': drivers/net/ethernet/mellanox/mlx5/core/debugfs.c:274:1: error: the frame size of 1104 bytes is larger than 1024 bytes [-Werror=frame-larger-than=] Revert the previous patch partially to use dynamically allocation as the code did before. Unfortunately there is no good error handling in case the allocation fails. Fixes: 57a6c5e992f5 ("net/mlx5: Replace hand written QP context struct with automatic getters") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2020-05-29net/mlx5e: Don't use err uninitialized in mlx5e_attach_decapNathan Chancellor
Clang warns: drivers/net/ethernet/mellanox/mlx5/core/en_tc.c:3712:6: warning: variable 'err' is used uninitialized whenever 'if' condition is false [-Wsometimes-uninitialized] if (IS_ERR(d->pkt_reformat)) { ^~~~~~~~~~~~~~~~~~~~~~~ drivers/net/ethernet/mellanox/mlx5/core/en_tc.c:3718:6: note: uninitialized use occurs here if (err) ^~~ drivers/net/ethernet/mellanox/mlx5/core/en_tc.c:3712:2: note: remove the 'if' if its condition is always true if (IS_ERR(d->pkt_reformat)) { ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~ drivers/net/ethernet/mellanox/mlx5/core/en_tc.c:3670:9: note: initialize the variable 'err' to silence this warning int err; ^ = 0 1 warning generated. It is not wrong, err is only ever initialized in if statements but this one is not in one. Initialize err to 0 to fix this. Fixes: 14e6b038afa0 ("net/mlx5e: Add support for hw decapsulation of MPLS over UDP") Link: https://github.com/ClangBuiltLinux/linux/issues/1037 Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2020-05-29net/mlx5: Kconfig: Fix spelling typoSaeed Mahameed
"mdoe"->"mode" Fixes: d956873f908c ("net/mlx5e: Introduce kconfig var for TC support") Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Reported-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
2020-05-29mlx5: fix xdp data_meta setup in mlx5e_fill_xdp_buffJesper Dangaard Brouer
The helper function xdp_set_data_meta_invalid() must be called after setting xdp->data as it depends on it. The bug was introduced in the cited patch below, and cause the kernel to crash when using BPF helper bpf_xdp_adjust_head() on mlx5 driver. Fixes: 39d6443c8daf ("mlx5, xsk: Migrate to new MEM_TYPE_XSK_BUFF_POOL") Reported-by: David Ahern <dsahern@kernel.org> Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com> Tested-by: David Ahern <dsahern@gmail.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2020-05-29nfp: flower: fix incorrect flag assignmentLouis Peens
A previous refactoring missed some locations the flags were renamed but not moved from the previous flower_ext_feats to the new flower_en_feats variable. This lead to the FLOW_MERGE and LAG features not being enabled. Fixes: e09303d3c4d9 ("nfp: flower: renaming of feature bits") Signed-off-by: Louis Peens <louis.peens@netronome.com> Signed-off-by: Simon Horman <simon.horman@netronome.com> Acked-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-29net: ethernet: dwmac: add ethernet glue logic for NXP imx8 chipFugang Duan
NXP imx8 family like imx8mp/imx8dxl chips support Synopsys MAC 5.10a IP. This patch adds settings for NXP imx8 glue layer: - clocks - dwmac address width - phy interface mode selection - adjust rgmii txclk rate v2: - adjust code sequences in order to have reverse christmas tree local variable ordering. Signed-off-by: Fugang Duan <fugang.duan@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-29stmmac: platform: add "snps, dwmac-5.10a" IP compatible stringFugang Duan
Add "snps,dwmac-5.10a" compatible string for 5.10a version that can avoid to define some plat data in glue layer. Signed-off-by: Fugang Duan <fugang.duan@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-29net: dsa: sja1105: avoid invalid state in sja1105_vlan_filteringVladimir Oltean
Be there 2 switches spi/spi2.0 and spi/spi2.1 in a cross-chip setup, both under the same VLAN-filtering bridge, both in the SJA1105_VLAN_BEST_EFFORT state. If we try to change the VLAN state of one of the switches (to SJA1105_VLAN_FILTERING_FULL) we get the following error: devlink dev param set spi/spi2.1 name best_effort_vlan_filtering value false cmode runtime [ 38.325683] sja1105 spi2.1: Not allowed to overcommit frame memory. L2 memory partitions and VL memory partitions share the same space. The sum of all 16 memory partitions is not allowed to be larger than 929 128-byte blocks (or 910 with retagging). Please adjust l2-forwarding-parameters-table.part_spc and/or vl-forwarding-parameters-table.partspc. [ 38.356803] sja1105 spi2.1: Invalid config, cannot upload This is because the spi/spi2.1 switch doesn't support tagging anymore in the SJA1105_VLAN_FILTERING_FULL state, so it doesn't need to have any retagging rules defined. Great, so it can use more frame memory (retagging consumes extra memory). But the built-in low-level static config checker from the sja1105 driver says "not so fast, you've increased the frame memory to non-retagging values, but you still kept the retagging rules in the static config". So we need to rebuild the VLAN table immediately before re-uploading the static config, operation which will take care, based on the new VLAN state, of removing the retagging rules. Fixes: 3f01c91aab92 ("net: dsa: sja1105: implement VLAN retagging for dsa_8021q sub-VLANs") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-29Merge branch 'mlx5-next' of ↵Saeed Mahameed
git://git.kernel.org/pub/scm/linux/kernel/git/mellanox/linux net/mlx5: Add ability to read and write ECE options net/mlx5: Add support for RDMA TX FT headers modifying net/mlx5: Move iseg access helper routines close to mlx5_core driver net/mlx5: Cleanup mlx5_ifc_fte_match_set_misc2_bits net/mlx5: Add support in forward to namespace {IB/net}/mlx5: Simplify don't trap code net/mlx5: Replace zero-length array with flexible-array Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2020-05-29net: phy: marvell: unlock after phy_select_page() failureDan Carpenter
We need to call phy_restore_page() even if phy_select_page() fails. Otherwise we are holding the phy_lock_mdio_bus() lock. This requirement is documented at the start of the phy_select_page() function. Fixes: a618e86da91d ("net : phy: marvell: Speedup TDR data retrieval by only changing page once") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-29net: phy: mscc: fix PHYs using the vsc8574_probeAntoine Tenart
PHYs using the vsc8574_probe fail to be initialized and their config_init return -EIO leading to errors like: "could not attach PHY: -5". This is because when the conversion of the MSCC PHY driver to use the shared PHY package helpers was done, the base address retrieval and the base PHY read and write helpers in the driver were modified. In particular, the base address retrieval logic was moved from the config_init to the probe. But the vsc8574_probe was forgotten. This patch fixes it. Fixes: deb04e9c0ff2 ("net: phy: mscc: use phy_package_shared") Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com> Reviewed-by: Michael Walle <michael@walle.cc> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.25.1) at 2024-10-26 08:31:50 +0000